ZYA-XS2HDD Multimedia Player

FCC STATEMENT 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

            !"# $% &  '   (!  )!!   * +,!*  , -,! #! . /!0   1 22222230(222. 4! . / !,!#! -,! 54- , -4- .-66 +,7#8  *  ,(#, 9(( 6!*6!4            6!3 !     1 !--  .!  !23 0( 22  !4 -- ,   #!  ,6  # 6!  !#  .#  !6,!6 #!! # ! 6!  , #! ,###.! #6  ,,-#!,#   , 64    6:##!    6:#!)6; 6)( ,  !,- !)! ##') <  # =,.< #!<  6  .> ! 

                         !"#  $    !! %  !!   &'  (  ) *    +,-./0 1    !" #1*          %  % %  2* 34&5  6'"%   !   ! %% !   '   %   " 7    8 %0* !   /  *%    %'! %  $'" ! %  %     !  % !   ' " %$' " % %  '! !"'!  '   %      9 "    % !     $'  %   '   % ,.+:,. '# %   '   %  %% !    %!  7  "!" ' ' ;  '   %     %#      <        < !=  ; =* %   % ! =  > " "=??#0%'  #  # # '@   

            !  "# $%&'(  '!   )! *+,-   .)'/       XTREAMER LIMITED  ˄0 ˖HDD Multimedia Player 'Xtreamer Sidewinder 2˅  1 22 ! 3/ 24   )1/ /5   44   /     62    678 27!   1 7 97 :, : &,2 2,2  ;     

FCC Certification label Sample

FCC Certification Label Location Sample Label location

1. RF EXPOSURE 1.1. The Requirement System operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See Section 15.247(b)(4) and Section 1.1307(b)(1) 1.2. Limit For Maximum Permissible Exposure (MPE) Limits for General Population/ Uncontrolled Exposure F = frequency in MHz, * Plane-wave equivalent power density 1.3. MPE Calculations E(V/m) = 30 P G d  , Power Density: S( 2 mW/cm) = 2 377 E Where E = Electric Field (V/m) P = Peak Output Power (mW) G = Antenna Numeric Gain (numeric) = 10 x , x = Antenna Gain(dBi) /10 d = Separation Distance (cm) Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) ( 2 mW/cm) Averaging Time 2 E, 2 H or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 f/1500 30 1500-100,000 1.0 30 We can change the formula to: S = 2 30 377 PG d   or, d = 30 377 PG S   Because the EUT is belong to general population/uncontrolled exposure. So 1.3.1. We considering the limit of minimum separation distance (d) is 20cm, Maximum Output Power = 53.95mW Antenna Gain = 5(dBi) = 3.16(numeric) S = 2 30 377 PG d   = 0.034 2 mW/cm < 1.0 2 mW/cm (limit) Calculated RF Exposure power density is 0.034 2 mW/cm , less than the limit. 1.3.2. We considering the limit of power density (S) is 1.0 2 mW/cm , Maximum Output Power = 53.95mW Antenna Gain = 5(dBi) = 3.16(numeric) d = 30 377 PG S   = 3.68cm < 20 cm Calculated RF Exposure separation distance is 3.68 cm, less than the minimum separation distance 1.3.3.FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm(8 inches) during normal operation. Proposed RF exposure safety information to include in User’s Manual.

Page 1 of 179 FCC ID: ZYA-XS2 ACCURATE TECHNOLOGY CO., LTD Report No.: ATE20111766 APPLICATION CERTIFICATION FCC Part 15C On Behalf of XTREAMER LIMITED HDD Multimedia Player Model No.: Xtreamer Sidewinder 2 FCC ID: ZYA-XS2 Prepared for : XTREAMER LIMITED Address : Unbo b/d 226-16, sukchon-dong, songpa-gu, Seoul, South Korea Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20111766 Date of Test : August 25-September 7, 2011 Date of Report : September 7, 2011 Page 2 of 179 FCC ID: ZYA-XS2 ACCURATE TECHNOLOGY CO., LTD Report No.: ATE20111766 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 5 1.1. Description of Device (EUT)....................................................................................................................5 1.2. Description of Test Facility ......................................................................................................................6 1.3. Measurement Uncertainty.........................................................................................................................6 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 7 3. OPERATION OF EUT DURING TESTING ................................................................................. 8 3.1. Operating Mode ........................................................................................................................................8 3.2. Configuration and peripherals ..................................................................................................................8 4. TEST PROCEDURES AND RESULTS ......................................................................................... 9 5. 6DB BANDWIDTH MEASUREMENT ........................................................................................ 10 5.1. Block Diagram of Test Setup..................................................................................................................10 5.2. The Requirement For Section 15.247(a)(2) ............................................................................................10 5.3. EUT Configuration on Measurement .....................................................................................................10 5.4. Operating Condition of EUT ..................................................................................................................10 5.5. Test Procedure ........................................................................................................................................11 5.6. Test Result ..............................................................................................................................................11 6. MAXIMUM PEAK OUTPUT POWER ....................................................................................... 22 6.1. Block Diagram of Test Setup..................................................................................................................22 6.2. The Requirement For Section 15.247(b)(3)............................................................................................22 6.3. EUT Configuration on Measurement .....................................................................................................22 6.4. Operating Condition of EUT ..................................................................................................................22 6.5. Test Procedure ........................................................................................................................................23 6.6. Test Result ..............................................................................................................................................23 7. POWER SPECTRAL DENSITY MEASUREMENT.................................................................. 34 7.1. Block Diagram of Test Setup..................................................................................................................34 7.2. The Requirement For Section 15.247(e).................................................................................................34 7.3. EUT Configuration on Measurement .....................................................................................................34 7.4. Operating Condition of EUT ..................................................................................................................34 7.5. Test Procedure ........................................................................................................................................35 7.6. Test Result ..............................................................................................................................................35 8. BAND EDGE COMPLIANCE TEST ........................................................................................... 46 8.1. Block Diagram of Test Setup..................................................................................................................46 8.2. The Requirement For Section 15.247(d) ................................................................................................46 8.3. EUT Configuration on Measurement .....................................................................................................46 8.4. Operating Condition of EUT ..................................................................................................................47 8.5. Test Procedure ........................................................................................................................................47 8.6. Test Result ..........................…

Text truncated - open the document above for the full version.

Conducted emissions test Radiated emissions test < 1GHz Radiated emissions test > 1GHz