2AD8UFZCWI2A1Wireless Access Point

Nokia Wi-Fi Access Point AC200i Regulatory Information Operation within 2.412-2.4835GHz / 5.15-5.25GHz / 5.725-5.85GHz frequency range is restricted to indoor environment. This device meets all the other requirements specified in Part 15E, Section 15.407 and 15.247 of the FCC Rules. Industry Canada statement: This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device does not cause harmful interference, and (2) this device must accept any interference received, including interference that can cause undesired operation. Ce dispositif est conforme à la norme CRN-247 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Wi-Fi Channels operating in the 5600-5650 MHz range are disabled by internal SW when this product is deployed in Canada and not configurable by the end user. Caution: (I) Users are also advised that high-power radars are allocated as primary users (for example priority users) of the bands 5600-5650MHz and that these radars can cause interference and/or damage to LE-LAN devices. Avertssement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les susmentionnées, notamment: (I) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radar de haute puissance sont désignés utilisateurs principaux (c.-à-d, qu’ils ont la priorité) pour les bandes 5600-5650MHz et que ces radars pourraient causer du brouillage et /ou des dommages aux dispositifs LAN-EL.

Package Contents • Access point • Bracket • Logo sticker • Quick Installation Guide Tools Required • Marker • Measuring tape • Screws • Screw driver • Hammer • Network cables • POE power or DC power adapter 1. Before unpacking the carton, ensure that the packaging is intact, not damaged or soaked. 2. Unpack the carton and check if all the items listed in the package contents are included. 3. Tools are not supplied with the WI2A-AC200i box. NOTE This Quick Installation Guide Nokia Wi-Fi Access Point WI2A-AC200i provides basic information and step-by-step installation instructions. Following these steps will enable you to properly install the WI2A-AC200i at your site. Thank you for buying a Nokia Wi-Fi Access Point WI2A-AC200i. Nokia Wi-Fi Access Point WI2A-AC200i Pre-requisites • Please read all the notes and safety statements in this guide before beginning the installation process. • The WI2A-AC200i is designed for an indoor environment (e.g. temperature range of 0°C to 40°C, non-condensing). • Allow 10 cm of space around the access point to ensure proper cooling. • Install the WI2A-AC200i away from heat sources, water/wet surfaces, and strong magnetic field sources or electrical appliances (ex: microwave ovens). • Using an incorrect power adapter may permanently damage the product. • Legal Notices The information contained herein is subject to change without notice. The only warranties for Nokia products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Nokia Solutions and Networks shall not be liable for technical or editorial errors or omissions contained herein. 1 234 Product Overview Off - LAN Connection Not Detected Red - LAN Connection Detected Red blinking - AP IP address Discovery process Green - AP IP address obtained (DHCP or Static but not factory default) Green blinking - LAN Activity after IP address has been obtained 2.4 GHz ETH 5 GHz Off - LAN Connection Not Detected or AP IP Address not available Red - AP IP address available but Controller IP is being discovered or Invalid Controller IP Red blinking - Controller IP Available and Connection in Progress Green -Connected to Controller and in steady state Green blinking - Connected to Controller and Configuration in Progress Amber blinking - Connected to Controller and Software Download in Progress PWR CTRL ETH 2.4G 5G LAN PORT Reset button Power port Security Lock Slot4 Used to reboot or restore WI2A-AC200i. Press and release the button to reboot WI2A-AC200i. Press and hold the button for 10 seconds to restore factory settings. Port for Ethernet cable to connect the WI2A-AC200i to LAN and POE (if available). Description Name Number 3 2 1 Specification Summary Weight Nokia WI2A-AC200i physical specification Nokia WI2A-AC200i electrical specification Nokia WI2A-AC200i environmental specification The following table describes the physical, electrical and environmental specifications. Item Description Dimensions 150mm x 150mm x 30mm (without bracket) 400g Item Description Power input +12V/1A ≤12W Power consumption Item Description Working temperature0°C ~ +40°C 5% to 95% non-condensing Operating humidity IP20 Dustproof and Waterproof • Regulatory Information Port to connect a DC power supply unit if POE is unavailable. Slot for security lock and cable for theft protection. PWR CTRL Off - No SSID Configured on 2.4 GHz Green - 2.4 GHz SSID Configured and Broadcasting Red – AP is locked by Controller Off - No SSID Configured on 5 GHz Green - 5 GHz SSID Configured and Broadcasting Red – AP is locked by Controller LED Color – Indication Off - No Power to AP Red - Board Power On Red blinking - Loading Software Green - Software Loaded Red blinking for more than 5 minutes - Failure to load Software properly (if LED control is working) Accessories Needed Label material and adhesive have been designed to last the lifetime of the product when installed in accordance with Nokia installation guidelines. © Nokia Solutions and Networks 2015. Label Statements Hardware Operation NOTE Ensure that Nokia WI2A-AC200i is securely installed. Poor installation may cause the device to fall and be damaged. There is a security lock slot with an anti-theft design provided on the WI2A-AC200i. 1. Fasten the security lock cable to an immovable object. 2. Insert the security lock cable into the security lock slot of the WI2A-AC200i and then lock it. Installing the security lock The box does not include a security lock cable. It needs to be purchased separately. 3 Voltage range: 37V~ 57V PD: 12.95W, support Category-5 Enhanced 100m cable 12 V DC nominal, +/- 5% PoE DC Power Adapter Item Name Description 1 2 1 The following figure illustrates the interface and cable connections of the WI2A-AC200i: Connecting cables • Category-5 Enhanced Ethernet cable is recommended. • Ensure that the WI2A-AC200i is connected to the LAN using a correct Ethernet cable. • The WI2A-AC200i might fail to power up or work if non-standard Ethernet cable is used. Ethernet cable DC Power adapter • A DC power adapter is required only if a PoE power supply is not available. 1. Align the securing hook of WI2A-AC200i with the bracket. 2. To firmly fasten the WI2A-AC200i to the bracket, rotate the bracket in the clockwise direction (as shown in the figure on the right) until it completely locks into the WI2A-AC200i. 3. Drive two screws in the wall with a distance of 79mm between them. 4. Align the bracket hole with the screws, and then pull the bracket down over the screws until it is tightly fastened. Recommended wall mounting for the WI2A-AC200i is with the cables run upward. If the cables are run downward, the Nokia Logo sticker can be placed on the WI2A-AC200i to display an upright Nokia logo. Cabling options are shown in the figure to the right. Scenario 2: Wall mounting 1 2 The WI2A-AC200i requires either PoE or DC power supply to operate. To use the PoE powe…

Text truncated - open the document above for the full version.

Declaration Letter Date: August 14, 2015 We, Nokia Solutions and Networks. declare that the product will be used in the system operators service area. Currently the end product is a non‐consumer product, certified and housed in a sealed enclosure, and is only accessible and installed by trained /approved maintenance personnel. This product is not marketed or available to the general public. FCC ID: 2AD8UFZCWI2A1 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! Terry Schwenk Title: R&D Engineer – Regulatory Compliance Nokia Solutions and Networks TEL: 1.847.809.6952 FAX: 1.224.248.8208 E‐mail: [email protected]

Date: 14 August 2015 GENERAL DECLARATION We,Nokia Solutions and Networks. declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: 2AD8UFZCWI2A1 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! ----------------------------------- Terry Schwenk Title: R&D Engineer – Regulatory Compliance Nokia Solutions and Networks TEL: 1.847.809.6952 FAX: 1.224.248.8208 E-mail: [email protected]

Request for Confidentiality Date: August 14, 2015 Confidentiality Request for: FCC ID: 2AD8UFZCWI2A1 IC: 109D-FZCWI2A01 To Whom It May Concern, Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, Nokia Solutions and Networks requests that a part of the subject FCC and/or IC application listed below be held permanently confidential and permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. • Operational Description • Block Diagram • Schematics/Parts List • Tu n e-up procedure • Operational description The Applicant has spent substantial effort in developing this product, some aspects of which are deemed to be trade secret and proprietary. Having the subject information easily available to our competitors in this market would negate the advantage we have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Sincerely yours, Terry Schwenk Title: R&D Engineer – Regulatory Compliance Nokia Solutions and Networks TEL:1.847.809.6952 FAX: 1.224.248.8208 E-mail: [email protected]

Internal photos Federal Communications Commission Authorization and Evaluation Division Date: August 14, 2015 Confidentiality Request FCC ID: 2AD8UFZCWI2A1 Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: Test Setup photos Thank you! Sincerely yours, Terry Schwenk Title: R&D Engineer – Regulatory Compliance Nokia Solutions and Networks TEL: 1.847.809.6952 FAX: 1.224.248.8208 E-mail: [email protected] External photos

AGENCY AUTHORIZATION LETTER Date: 2015-09-22 FCC ID: 2AD8UFZCWI2A1 We, the undersigned, hereby authorize MRT Technology (Suzhou) Co., Ltd to act on our behalf, to act on our behalf in all manners relating to FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by MRT Technology (Suzhou) Co., Ltd within the scope of this authorization shall have the same effects as our own. Name Representative of agent: Robin Wu Agent Company name: MRT Technology (Suzhou) Co., Ltd Address: D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone, City: Suzhou Country China If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, Terry Schwenk Title: R&D Engineer – Regulatory Compliance Nokia Solutions and Networks TEL: 1.847.809.6952 FAX: 1.224.248.8208 E-mail: [email protected]

Appendix - EUT Photograph (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo (8) EUT Photo (9) EUT Photo (POE) (10) EUT Photo (POE) (11) EUT Photo (POE)

Label Label Location

Appendix - EUT Photograph (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo (8) EUT Photo (9) EUT Photo (10) EUT Photo (11) EUT Photo (12) EUT Photo (13) EUT Photo

MRT Technology (Suzhou) Co., Ltd Report No.: 1506RSU00614 Phone: +86-512-66308358 Report Version: V01 Fax: +86-512-66308368 Issue Date: 10-01-2015 Web: www.mrt-cert.com FCC ID: 2AD8UFZCWI2A1 Page Number: 1 of 7 RF Exposure Evaluation Declaration FCC ID: 2AD8UFZCWI2A1 APPLICANT: Nokia Solutions and Networks Application Type: Certification Product: Wireless Access Point Model No.: WI2A-AC200i Trademark: Nokia FCC Classification: Digital Transmission System (DTS) Unlicensed National Information Infrastructure (UNII) Reviewed By : ( Robin Wu ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 1506RSU00614 FCC ID: 2AD8UFZCWI2A1 Page Number: 2 of 7 Revision History Report No. Version Description Issue Date 1506RSU00614 Rev. 01 Initial report 10-01-2015 Report No.: 1506RSU00614 FCC ID: 2AD8UFZCWI2A1 Page Number: 3 of 7 1. PRODUCT INFORMATION 1.1. Equipment Description Product Name Wireless Access Point Model No. WI2A-AC200i Brand Name Nokia Hardware Version v2.0 Wi-Fi Specification 802.11a/b/g/n/ac Frequency Range 2.4GHz: For 802.11b/g/n-HT20: 2412 ~ 2462 MHz For 802.11n-HT40: 2422 ~ 2452 MHz 5GHz: For 802.11a/n-HT20/ac-VHT20:: 5180~5240MHz, 5745~5825MHz For 802.11n-HT40/ac-VHT40: 5190~5230MHz, 5755~5795MHz For 802.11ac-VHT80: 5210MHz, 5775MHz Type of Modulation 802.11b: DSSS 802.11g/a/n/ac: OFDM Maximum Average Output Power For 2.4GHz Band: 802.11b: 26.36dBm 802.11g: 25.49dBm 802.11n-HT20: 25.39dBm 802.11n-HT40: 25.46dBm For 5GHz Band: 802.11a: 26.29dBm 802.11n-HT20: 26.09dBm 802.11n-HT40: 25.98dBm 802.11ac-VHT20: 26.18dBm 802.11ac-VHT40: 26.00dBm 802.11ac-VHT80: 21.15dBm Report No.: 1506RSU00614 FCC ID: 2AD8UFZCWI2A1 Page Number: 4 of 7 1.2. Antenna Description Antenna Type Frequency Band (MHz) Tx Paths Per Chain Max Antenna Gain (dBi) Beam Forming Directional Gain (dBi) CDD Directional Gain (dBi) Ant 1 Ant 2 PCB Antenna 2412 ~2462 2 3.23 2.38 5.83 5.83 5150 ~ 5250 2 5.40 4.53 7.99 7.99 5725 ~ 5850 2 6.00 5.86 8.94 8.94 1. The EUT supports Cyclic Delay Diversity (CDD) technology for 802.11a/b/g mode, and CDD signals are correlated. 2. The EUT supports Beam Forming technology for 802.11n/ac mode, and exclude 802.11b/g mode. Correlated signals include, but are not limited to, signals transmitted in any of the following modes:  Unequal Antenna gains, with equal transmit powers. For Antenna gains given by G 1 , G 2 , ..., G N dBi transmit signals are correlated, then  Directional gain = 10*log[(10 G1/20 + 10 G2/20 + ... + 10 GN/20 ) 2 /N ANT ] dBi [Note the “20”s in the denominator of each exponent and the square of the sum of terms; the object is to combine the signal levels coherently.] For example: 5250 ~ 5350MHz Directional Gain = 10*log[(10 5.40/20 + 10 4.53/20 ) 2 /2] = 7.99 dBi Report No.: 1506RSU00614 FCC ID: 2AD8UFZCWI2A1 Page Number: 5 of 7 2. RF Exposure Evaluation 2.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- f/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- f/1500 6 1500-100,000 -- -- 1 30 f= Frequency in MHz Calculation Formula: Pd = (Pout*G)/(4*pi*r2) Where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 r = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1mW/cm². If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Report No.: 1506RSU00614 FCC ID: 2AD8UFZCWI2A1 Page Number: 6 of 7 2.2. Test Result of RF Exposure Evaluation Product Wireless Access Point Test Item RF Exposure Evaluation Antenna Gain: The maximum Gain measured in fully anechoic chamber is 5.83dBi for 2.4GHz, 7.99dBi for 5.2GHz and 8.94dBi for 5.80GHz in logarithm scale. For 2.4GHz ISM Band: Test Mode Frequency Band (MHz) Maximum Average Output Power (dBm) Power Density at R = 20 cm (mW/cm 2 ) Limit (mW/cm 2 ) 802.11b/g/n-HT20/ n-HT40 2412 ~ 2462 26.36 0.3294 1 For 5GHz UNII Band: Test Mode Frequency Band (MHz) Maximum Average Output Power (dBm) Power Density at R = 20 cm (mW/cm 2 ) Limit (mW/cm 2 ) 802.11a/n-HT20/ n-H40/ac-VHT20 ac-VHT40/ac-VHT80 5180 ~ 5240 26.29 0.5330 1 5725 ~ 5825 26.22 0.6527 1 Report No.: 1506RSU00614 FCC ID: 2AD8UFZCWI2A1 Page Number: 7 of 7 CONCULISON: Both of the WLAN 2.4GHz Band and WLAN 5GHz Band can transmit simultaneously. Therefore, the Max Power Density at R (20 cm) = 0.3294mW/cm 2 + 0.6527mW/cm 2 = 0.9821mW/cm 2 < 1mW/cm 2 . So the EUT complies with the requirement. The End

MRT Technology (Suzhou) Co., Ltd Report No.: 1506RSU00611 Phone: +86-512-66308358 Report Version: V01 Fax: +86-512-66308368 Issue Date: 10-23-2015 Web: www.mrt-cert.com FCC ID: 2AD8UFZCWI2A1 Page Number: 1 of 219 IC: 109D-FZCWI2A01 FCC ID: 2AD8UFZCWI2A1 IC: 109D-FZCWI2A01 APPLICANT: Nokia Solutions and Networks Application Type: Certification Product: Wireless Access Point Model No.: WI2A-AC200i Trademark: Nokia FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15.247 IC Rule(s): RSS-247 Issue 1 Test Procedure(s): ANSI C63.10-2013, KDB 558074 D01v03r03, KDB 662911 D01v02r01 Test Date: June 16 ~ August 14, 2015 MEASUREMENT REPORT FCC PART 15.247 & IC RSS-247 WLAN 802.11b/g/n Reviewed By : ( Robin Wu ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 558074 D01v03r03. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 2 of 219 IC: 109D-FZCWI2A01 Revision History Report No. Version Description Issue Date 1506RSU00611 Rev. 01 Initial report 10-01-2015 1506RSU00611 Rev. 02 Revised the PSD test data 10-23-2015 Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 3 of 219 IC: 109D-FZCWI2A01 CONTENTS Description Page §2.1033 General Information .......................................................................................................... 5 1. INTRODUCTION ...................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ...................................................................................................... 7 2.1. Equipment Description ................................................................................................. 7 2.2. Working Frequencies.................................................................................................... 8 2.3. Description of Available Antennas ................................................................................ 9 2.4. Description of Antenna RF Port .................................................................................. 10 2.5. Test Mode .................................................................................................................. 10 2.6. Device Capabilities ...................................................................................................... 11 2.7. Test Configuration ...................................................................................................... 12 2.8. EMI Suppression Device(s)/Modifications ................................................................... 12 2.9. Labeling Requirements ............................................................................................... 12 3. DESCRIPTION of TEST ......................................................................................................... 13 3.1. Evaluation Procedure ................................................................................................. 13 3.2. AC Line Conducted Emissions ................................................................................... 13 3.3. Radiated Emissions .................................................................................................... 14 4. ANTENNA REQUIREMENTS................................................................................................. 15 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................. 16 6. MEASUREMENT UNCERTAINTY ......................................................................................... 17 7. TEST RESULT ....................................................................................................................... 18 7.1. Summary .................................................................................................................... 18 7.2. 6dB Bandwidth Measurement ..................................................................................... 20 7.2.1. Test Limit ................................................................................................................ 20 7.2.2. Test Procedure used ............................................................................................... 20 7.2.3. Test Setting ............................................................................................................. 20 7.2.4. Test Setup .............................................................................................................. 20 7.2.5. Test Result .............................................................................................................. 21 7.3. Output Power Measurement ....................................................................................... 30 7.3.1. Test Limit ................................................................................................................ 30 7.3.2. Test Procedure Used .............................................................................................. 30 7.3.3. Test Setting ............................................................................................................. 30 Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 4 of 219 IC: 109D-FZCWI2A01 7.3.4. Test Setup ............................................................…

Text truncated - open the document above for the full version.

Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 51 of 219 IC: 109D-FZCWI2A01 802.11b AVGPSD - Ant 2 / Ant 1 + 2 Channel 01 (2412MHz) Channel 06 (2437MHz) Channel 11 (2462MHz) Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 52 of 219 IC: 109D-FZCWI2A01 802.11g AVGPSD - Ant 2 / Ant 1 + 2 Channel 01 (2412MHz) Channel 06 (2437MHz) Channel 11 (2462MHz) Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 53 of 219 IC: 109D-FZCWI2A01 802.11n-HT20 AVGPSD - Ant 2 / Ant 1 + 2 Channel 01 (2412MHz) Channel 06 (2437MHz) Channel 11 (2462MHz) Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 54 of 219 IC: 109D-FZCWI2A01 802.11n-HT40 AVGPSD - Ant 2 / Ant 1 + 2 Channel 03 (2422MHz) Channel 06 (2437MHz) Channel 09 (2452MHz) Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 55 of 219 IC: 109D-FZCWI2A01 7.5. Conducted Band Edge and Out-of-Band Emissions 7.5.1. Test Limit The limit for out-of-band spurious emissions at the band edge is 30dB below the fundamental emission level, as determined from the in-band power measurement of the DTS channel performed in a 100 kHz bandwidth per the PSD procedure. 7.5.2. Test Procedure Used KDB 558074 D01v03r03 - Section 11.2 & Section 11.3 7.5.3. Test Settitng 1. Reference level measurement (a) Set instrument center frequency to DTS channel center frequency (b) Set the span to ≥ 1.5 times the DTS bandwidth (c) Set the RBW = 100 kHz (d) Set the VBW ≥ 3 x RBW (e) Detector = peak (f) Sweep time = auto couple (g) Trace mode = max hold (h) Allow trace to fully stabilize 2. Emission level measurement (a) Set the center frequency and span to encompass frequency range to be measured (b) RBW = 100kHz (c) VBW = 300kHz (d) Detector = Peak (e) Trace mode = max hold (f) Sweep time = auto couple (g) The trace was allowed to stabilize Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 56 of 219 IC: 109D-FZCWI2A01 7.5.4. Test Setup Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 57 of 219 IC: 109D-FZCWI2A01 7.5.5. Test Result Test Mode Data Rate (Mbps) Channel No. Frequency (MHz) Limit Result Ant 1 802.11b 1 01 2412 30dBc Pass 802.11b 1 06 2437 30dBc Pass 802.11b 1 11 2462 30dBc Pass 802.11g 6 01 2412 30dBc Pass 802.11g 6 06 2437 30dBc Pass 802.11g 6 11 2462 30dBc Pass 802.11n-HT20 6.5 01 2412 30dBc Pass 802.11n-HT20 6.5 06 2437 30dBc Pass 802.11n-HT20 6.5 11 2462 30dBc Pass 802.11n-HT40 13.5 03 2422 30dBc Pass 802.11n-HT40 13.5 06 2437 30dBc Pass 802.11n-HT40 13.5 09 2452 30dBc Pass Ant 2 802.11b 1 01 2412 30dBc Pass 802.11b 1 06 2437 30dBc Pass 802.11b 1 11 2462 30dBc Pass 802.11g 6 01 2412 30dBc Pass 802.11g 6 06 2437 30dBc Pass 802.11g 6 11 2462 30dBc Pass 802.11n-HT20 6.5 01 2412 30dBc Pass 802.11n-HT20 6.5 06 2437 30dBc Pass 802.11n-HT20 6.5 11 2462 30dBc Pass 802.11n-HT40 13.5 03 2422 30dBc Pass 802.11n-HT40 13.5 06 2437 30dBc Pass 802.11n-HT40 13.5 09 2452 30dBc Pass Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 58 of 219 IC: 109D-FZCWI2A01 802.11b Out-of-Band Emissions - Ant 1 100kHz PSD Reference Level Channel 01 (2412MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 59 of 219 IC: 109D-FZCWI2A01 Channel 11 (2462MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 60 of 219 IC: 109D-FZCWI2A01 802.11g Out-of-Band Emissions - Ant 1 100kHz PSD Reference Level Channel 01 (2412MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 61 of 219 IC: 109D-FZCWI2A01 Channel 11 (2462MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 62 of 219 IC: 109D-FZCWI2A01 802.11n-HT20 Out-of-Band Emissions - Ant 1 100kHz PSD Reference Level Channel 01 (2412MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 63 of 219 IC: 109D-FZCWI2A01 Channel 11 (2462MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 64 of 219 IC: 109D-FZCWI2A01 802.11n-HT40 Out-of-Band Emissions - Ant 1 100kHz PSD Reference Level Channel 03 (2422MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 65 of 219 IC: 109D-FZCWI2A01 Channel 09 (2452MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 66 of 219 IC: 109D-FZCWI2A01 802.11b Out-of-Band Emissions - Ant 2 100kHz PSD Reference Level Channel 01 (2412MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 67 of 219 IC: 109D-FZCWI2A01 Channel 11 (2462MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 68 of 219 IC: 109D-FZCWI2A01 802.11g Out-of-Band Emissions - Ant 2 100kHz PSD Reference Level Channel 01 (2412MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 69 of 219 IC: 109D-FZCWI2A01 Channel 11 (2462MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 70 of 219 IC: 109D-FZCWI2A01 802.11n-HT20 Out-of-Band Emissions - Ant 2 100kHz PSD Reference Level Channel 01 (2412MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 71 of 219 IC: 109D-FZCWI2A01 Channel 11 (2462MHz) High Band Edge Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 72 of 219 IC: 109D-FZCWI2A01 802.11n-HT40 Out-of-Band Emissions - Ant 2 100kHz PSD Reference Level Channel 03 (2422MHz) Low Band Edge Spurious Emission Channel 06 (2437MHz) Spurious Emission Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 73 of 219 IC: 109D-FZCWI2A01 Channel 09 (2452MHz) Hi…

Text truncated - open the document above for the full version.

Report No.: 1506RSU00611 FCC ID: 2AD8UFZCWI2A1 Page Number: 101 of 219 IC: 109D-FZCWI2A01 Test Mode: 802.11n-HT40 - Ant 2 Test Site: AC1 Test Channel: 09 Test Engineer: Roy Cheng Remark: 1. Average measurement was not performed if peak level lower than average limit. 2. Other frequency was 20dB below limit line within 1-18GHz, there is not show in the report. Mark Frequency (MHz) Reading Lev…

Text truncated - open the document above for the full version.