2ASIVPGD768FNULockly Guard Fingerprint Deadbolt 728FZ Z-Wave Smart Lock, Lockly Guard Deadbolt 728Z Z-Wave Smart Lock

ERP机型：PL4516FQ-GL-SMT00031A-V1 Designer：曹显贵Date：2024-05-23 描述: 说明书（双语）:PL4516FQ/PGD768FNU,SMT000,REV.A(UMPGD768FNU20240523), 196×196mm,80g书纸,双面印单黑,38页76面装订本,RoHS2.0,REACH,Prop65,POPs,PAHs ERP P/N： K K REV：1.1 封面 USER MANUAL MANUEL D'UTILISATION For commercial use & professional installation Pour usage commercial et installation professionnelle www.LocklyPRO.com DEADBOLT 728F ZU DEADBOLT 728 ZU Z-Wave Smart Lock Serrure intelligente Z-Wave PGD728F ZU | PGD728 ZU Table of Contents TABLE OF CONTENTS 2.1 Product Overview - Exterior 2.2 Product Overview - Interior 2.3 Understanding Your New Lock 2.4 Reset Button 2.5 Keypad Display Switch 2.6 Rebooting Your Lock 2.7 Low Battery 2.8 Changing The Battery Section 1 - Product Highlights Section 2 - Product Overview Section 3 - Using Your Smart Lock 3.1 Configuring Access 3.2 Entering Programming Mode 3.3 Adding an Access Code 3.4 Deleting an Access Code 3.5 Checking an Access Code 3.6 Z-Wave Settings 3.7 Adding a Fingerprint* 3.8 Fingerprint Scanning Directions* 3.9 Fingerprint Scanning Tips & Troubleshoot* 3.10 Deleting Stored Fingerprints* 3.11 Adding Secure Link Section 4 - Locking and Unlocking 1.1 Product Features 4.2 Unlocking with Fingerprints* 4.3 Locking / Unlocking with LocklyPRO App 4.4 Locking / Unlocking with Physical Key 4.5 Safe Mode 4.6 Rain Mode 4.7 Shine Mode 4.8 Welcome Mode Section 5 - Advanced Features 5.1 Offline Access Code TM (OAC) Section 6 - Important Notes 6.1 Important Notes Section 7 - Cleaning 7.1 Cleaning Section 8 - Safety Precautions 8.1 Safety Precautions For additional support, visit LocklyPRO.com/support or email [email protected] 1 2 3 4 5 5 6 7 8 9 10 11 13 15 17 16 20 21 22 23 24 25 26 27 28 30 31 31 32 33 34 35 4.1 Unlocking with Access Codes *only available on 728F ZU Patented Hack-Proof PIN Genie Keypad Digits are randomly displayed on the keypad ensuring access codes to be undetectable to intruders after repeated use. Numbers are randomly distributed across 4 buttons, with 3 numbers in each button. Users can press any button showing their number. Location of the numbers are always different every time someone uses the keypad, making it hard for prying eyes to guess the correct code. Built in Z-Wave® module Integrate with your Z-Wave smart home system, supports 2GIG GC2E and IQpanel QS9207 Z-Wave controller to lock and unlock from anywhere. Multiple Access Codes & Monitoring Store up to 43(Generate up to 33 PIN access codes on Lockly App & up to 10 PIN access codes via Z-Wave controller.) Access Codes for family, friends and guests, as well as monitor entry and exit records. Advanced 3D Fingerprint Recognition Biometric Fingerprint Recognition protocol allows up to 99 registered fingerprints to be used and accepts only actual fingerprints - preventing lifted prints from being used. ( only on PGD728F ZU ) Live Monitoring and Voice Control Through your smartphone, monitor door access from anywhere in the world and securely control who comes and goes with the Secure Link Wi-Fi Hub. (Requires Secure Link Wi-Fi hub, sold separately PGH200) Complete Privacy The exterior displayed keypad can be locked and switched off using the simple ON/OFF toggle from the inside panel. The owner can prevent others trying to input the passcode from the outside and entering the home. Offline Access Code™ (OAC) The Offline Access Code™ can allow owners to issue access codes, set the allowed access duration, all without Lock ever connecting to the internet, so in case of power outage, you can still magically and remotely issue Access Codes without any connection to the web. Backup Keys and 9V Battery Socket The door can be opened with physical backup keys. There is also a 9V battery connection socket for emergency power backup to access the keypad in case your smart lock runs out of battery. 1.1 Product Features SECTION 1.11 ENG 2.1 Product Overview - Exterior SECTION 2.12 ENG Reboot Welcome/Safe Mode Indicator Battery Indicator OK Button Key Hole Cover 9V Battery Socket Key Hole Fingerprint Sensor 2.2 Product Overview - Interior SECTION 2.2 3 ENG Battery Compartment ( Operated by 4 x AA Batteries) Battery Cover Display Keypad Switch Thumbturn Beep Alert Program Button Reset Button 2.3 Understanding Your New Lock SECTION 2.3 After the installation of your new Lockly Guard, understanding some key functions of operat- ing your smart lock is important. The following guides will walk you through resetting a lock, adding Access Codes, deleting Access Codes, adding and deleting fingerprints, and how to configure your OAC (Offline Access Code ™ ). For any questions you can always visit LocklyPRO.com/support for assistance. Don’t forget that Lockly Guard works best with our iOS and Android app. Please download the app by visiting the link below. 4 Scan or visit LocklyPRO.com/app ENG Lockly Guard supports working in both Z-Wave mode and LocklyPRO app mode. Z-Wave controller takes precedence over Lockly App. If you set the clock and time zone or auto-locking through Z-Wave, the door lock will prioritize the Z-Wave controller settings. 2.4 Reset Button SECTION 2.4 ~ 2.55 2.5 Keypad Display Switch The exterior keypad screen can be locked and turned off by using the ON/OFF switch at the back panel (interior) of the smart lock. When it is switched off, people who are outside cannot enter any access codes to unlock the door. OFF ON If you need to reset, you must have your Activation Code. The Activation Code can be found on the Activation Code Card that came with the smart lock. Once the smart lock has been reset, all the data previously stored will be deleted, after which you need to reset Z-Wave. See below which Reset procedure applies for you. ENG Never Connected to Lockly App Press Reset Button for 3 seconds, and the smart lock will restart and reset. Connected to Lockly App In the Settings menu of the App, select Perform Factory Reset. The smart lock will restart and reset. After reset, you'll need the Activation Code to reconnect to the App. …

Text truncated - open the document above for the full version.

PIN GENIE, INC. DBA LO C K LY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Rev 1/26/2023 Date: 2023-11-17 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d) (7) Filing Grantee Code: 2ASIV PIN GENIE, INC. DBA LOCKLY certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information: Name: PIN GENIE, INC. DBA LOCKLY FRN: 0028246908 Address: 676 Transfer Rd., St. Paul, Minnesota 55114, United States Contact Person: Cindy zhou Tel.: 4159109522 Email: [email protected] Sincerely, Signatory [Cindy zhou, COO]

PINGENIE,INC.DBALOCKLY 676TransferRd.,St.Paul,Minnesota55114,UnitedStates Date:2024-06-20 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing SUBJECT:FCCApplicationforFCCID:2ASIVPGD768FNU ToWhomItMayConcern: PINGENIE,INC.DBALOCKLYcertifiesthattheequipmentforwhichauthorizationissoughtisnot“covered” equipmentprohibitedfromreceivinganequipmentauthorizationpursuanttosection2.903oftheFCCrules. Sincerely, Signatory [Cindyzhou,COO]

PINGENIE,INC.DBALOCKLY 676TransferRd.,St.Paul,Minnesota55114,UnitedStates Date:2024-06-20 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing SUBJECT:FCCApplicationforFCCID:2ASIVPGD768FNU ToWhomItMayConcern: PINGENIE,INC.DBALOCKLYcertifiesthat,asofthedateofthefilingoftheapplication,theapplicantisnot identifiedontheCoveredList(asaspecificallynamedentityoranyofitssubsidiariesoraffiliates)asanentity producing“covered”equipment. Sincerely, Signatory [Cindyzhou,COO]

PINGENIE,INC.DBALOCKLY 676TransferRd.,St.Paul,Minnesota55114,UnitedStates Date:2024-06-20 FEDERALCOMMUNICATIONSCOMMISSION AUTHORIZATIONANDEVALUATIONDIVISION 7435OAKLANDMILLSROAD COLUMBIA,MD21046 SUBJECT:FCCID:2ASIVPGD768FNU ModelDeclarationLetter DearRegulatoryAuthority, Model(s):PGD728ZUaresametothemodelPGD728FZU,thesemodelsaresamePCBLayout,Schematics,BOM. Onlyfordifferentmodelname,Appearance,functionandlabelfordifferentmarketrequire. Thedifferenceslistasbelow LocationFunction(Appearance)ProductNameLabelinginformation Model: PGD728FZU Supportfingerprintunlocking LocklyGuard Fingerprint Deadbolt728FZ Z-WaveSmartLock Model: PGD728ZU Doesnotsupportfingerprint unlocking LocklyGuard Deadbolt728Z Z-WaveSmartLock Sincerely, Signatory [Cindyzhou,COO]

PINGENIE,INC.DBALOCKLY 676TransferRd.,St.Paul,Minnesota55114,UnitedStates Date:2024-06-20 FEDERALCOMMUNICATIONSCOMMISSION AUTHORIZATIONANDEVALUATIONDIVISION 7435OAKLANDMILLSROAD COLUMBIA,MD21046 SUBJECT:FCCApplicationforFCCID:2ASIVPGD768FNU ConfidentialityRequest Towhomitmayconcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,wearerequestingthe Commissiontowithholdthefollowingattachment(s)asconfidentialdocumentsfrompublicdisclosureindefinitely. ☒ BlockDiagram ☐ Tune-UpInformation ☒ OperationalDescription ☐ SecurityInformation ☒ Schematics ☐ SoftwareDefinedRadio(SDR)Information ☐ PartsList Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedtothepublic.The publicdisclosureofthesematerialsmaybeharmfultotheapplicantandprovideunjustifiedbenefitstoits competitors. Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulationsinTitle47CFR §2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthatbusinesssensitiveinformation remainsconfidentialuntiltheactualmarketingofnewlyauthorizeddevices,werequestShortTermConfidentiality ofthefollowingattachment(s); ☐ ExternalPhotos ☐ TestSetupPhotos ☐ InternalPhotos ☐ UserManual ☐For45days,pursuanttoPublicNoticeDA04-1705. or ☐For180dayspursuanttoKDB726920D01. TheapplicantunderstandsthatpursuanttoSection0.457oftheRules,disclosureofthisapplicationandall accompanyingdocumentationwillnotbemadebeforethedateoftheGrantforthisapplication. Sincerely, Signatory [CindyZhou,COO]

PINGENIE,INC.DBALOCKLY 676TransferRd.,St.Paul,Minnesota55114,UnitedStates Date:2024-06-20 FEDERALCOMMUNICATIONSCOMMISSION AUTHORIZATIONANDEVALUATIONDIVISION 7435OAKLANDMILLSROAD COLUMBIA,MD21046 SUBJECT:FCCApplicationforFCCID:2ASIVPGD768FNU POWEROFATTORNEY ToWhomItMayConcern: We,theundersigned,herebyauthorizeWaltekTestingGroup(Shenzhen)Co.,Ltd.JandySoonourbehalf,to applytotheFederalCommunicationsCommissiononourequipment.AnyandallactscarriedoutbyWaltek TestingGroup(Shenzhen)Co.,Ltd.JandySoonourbehalfshallhavethesameeffectasactsofourown. ThisistoadvisethatweareinfullcompliancewiththeAnti-DrugAbuseAct.We,PINGENIE,INC.DBA LOCKLYarenotsubjecttoadenialoffederalbenefitspursuanttoSection5301oftheAnti-DrugActof1988, 21USC853a,andnopartytotheapplicationissubjecttoadenialoffederalbenefitspursuanttothatsection. Sincerely, Signatory [Cindyzhou,COO]

Reference No.: WTX24X05111496W001/002 Page 2 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Reference No.: WTX24X05111496W001/002 Page 3 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 3 EUT View 4 Reference No.: WTX24X05111496W001/002 Page 4 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 5 EUT View 6 Reference No.: WTX24X05111496W001/002 Page 5 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 7 EUT View 8 Reference No.: WTX24X05111496W001/002 Page 6 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 9 EUT View 10 Reference No.: WTX24X05111496W001/002 Page 7 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 11 EUT View 12 Reference No.: WTX24X05111496W001/002 Page 8 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 13

Reference No.: WTX24X05111496W001/002 Page 1 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

Reference No.: WTX24X05111496W001/002 Page 9 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 EUT Housing and Board View 2 Reference No.: WTX24X05111496W001/002 Page 10 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT Housing and Board View 3 Solder Board-Component View 1 Reference No.: WTX24X05111496W001/002 Page 11 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 2 Solder Board-Component View 3 Reference No.: WTX24X05111496W001/002 Page 12 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 4 Solder Board-Component View 5 Reference No.: WTX24X05111496W001/002 Page 13 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 6 Solder Board-Component View 7 Reference No.: WTX24X05111496W001/002 Page 14 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 8 Solder Board-Component View 9 Reference No.: WTX24X05111496W001/002 Page 15 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 10 Solder Board-Component View 11 Reference No.: WTX24X05111496W001/002 Page 16 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 12 Antenna View 1 Zwave Antenna Reference No.: WTX24X05111496W001/002 Page 17 of 19 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Antenna View 2 BT Antenna

1. RF Exposure Requirements 1.1 General Information Client Information Applicant: PIN GENIE, INC. DBA LOCKLY Address of applicant: 676 Transfer Rd., St. Paul, MN 55114 Manufacturer: Smart Electronic Industrial (Dong Guan) Co., Ltd. Address of manufacturer: Qing Long Road, Long Jian Tian Village, Huang Jiang Town, Dong Guan, Guang Dong, China General Description of EUT: Product Name: Lockly Guard Fingerprint Deadbolt 728FZ Z-Wave Smart Lock; Lockly Guard Deadbolt 728Z Z-Wave Smart Lock Trade Name LOCKLY Model No.: PGD728F ZU Adding Model(s): PGD728 ZU Rated Voltage: DC6V Power Adapter: / Power Adapter: / FCC ID: 2ASIVPGD768FNU Equipment Type: Mobile device Technical Characteristics of EUT: Bluetooth Bluetooth Version: V5.0 (BLE mode) Frequency Range: 2402-2480MHz RF Output Power: -3.842dBm (Conducted) Data Rate: 1Mbps Modulation: GFSK Quantity of Channels: 40 Channel Separation: 2MHz Type of Antenna: FPC Antenna Antenna Gain: 1.8dBi Z-Wave Frequency Range: 908.42MHz Max. Field Strength: 94.71dBuV/m Modulation: FSK Quantity of Channels: / Channel Separation: / Antenna Type: FPC Antenna Antenna Gain: 0.77dBi 1.2 RF Exposure Exemption According to §1.1307(b)(3) and KDB 447498 D04 Interim General RF Exposure Guidance v01, system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. Option A: FCC Rule Part 1.1307 (b)(3)(i)(A):The available maximum time-averaged power is no more than 1mW, regardless of separation distance. Option B: FCC Rule Part 1.1307 (b)(3)(i)(B): The available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. P th is given by: Option C: FCC Rule Part 1.1307 (b)(3)(i)(C): The minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. R must be at least λ/2π, where λ is the free-space operating wavelength in meters. Single RF Sources Subject to Routine Environmental Evaluation RF Source frequency (MHz) Threshold ERP (watts) 0.3-1.34 1,920 R 2 1.34-30 3,450 R 2 /f 2 30-300 3.83 R 2 300-1,500 0.0128 R 2 f 1,500-100,000 19.2R 2 For Multiple RF sources: FCC Rule Part 1.1307(b)(3)(ii): (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging period, in which case they may be treated as a single source (separation is not required). (B) In the case of fixed RF sources operating in the same time-averaging period, or of multiple mobile or portable RF sources within a device operating in the same time averaging period, if the sum of the fractional contributions to the applicable thresholds is less than or equal to 1 as indicated in the following equation. 1.3 Calculated Result Radio Access Technology Prediction Frequency Output Power Antenna Gain Duty Cycle Tune-Up Time-Averaged Power ERP (MHz) (dBm) (dBi) (%) (dBm) (dBm) Bluetooth 2402 -3.842 1.8 100 -3.00 -3.35 Z-Wave 908.42 -1.32 0.77 100 -1.00 -2.38 Frequency Option Min. Distance Max. Power Exposure Limit Ratio Result (MHz) (cm) (dBm) (mW) (mW) Pass/Fail 2402 C 20.00 -3.35 0.46 768.00 0.01 Pass 908.42 C 20.00 -2.38 0.58 465.11 0.01 Pass Note: 1. a. Time-Averaged Power=Output Power * Duty Cycle; ERP= Time-Averaged Power+ Antenna gain-2.15dB; b. EIRP= E-104.8+20logD; Output Power=EIRP- Antenna Gain; ERP=EIRP-2.15dB 2. Option A, B and C refers as clause 1.2. 3. For option B, Max (time-averaged power, effective radiated power (ERP)) converts to Max. Power. For option C, ERP converts to Max. Power; 4. For option B, P th (mW) converts to Exposure Limit (mW); For option C, ERP (W) converts to Exposure Limit (mW). 5. Ratio= Tune-Up ERP (mW)/ Exposure Limit (mW) Mode for Simultaneous Multi-band Transmission: Radio Access Technology Ratio 1 Ratio 2 Simultaneous Ratio Limit Result Pass/Fail Bluetooth + Z-Wave 0.01 0.01 0.02 1 Pass Result: Pass

ShenzhenGolden-Resource Electronic Co.,Ltd. SPECIFICATION FOR APPROVAL Date 2024/06/16 File No 24061601 Revision 1.0 CUSTOMER: SMART ELECTRONIC INDUSTRIAL CO.,LTD. CUSTOMER NO: PGD728-V03 BT Antenna L 155mmMHF PART NAME: BT Antenna L=155mmMHF SUPPLIER NO: YJ029W.300146.W01 Date: Q"TY: PCS CUSTOMER APPROVED BY APPROVALCHIEFSUPERVISOR SUPPLIER SIGNATURE APPROVALCHECKDESIGN add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen APPROVALCHECKDESIGN ChenGuoqiangXieLiChenXingcheng YJ-RD-F04-A Spec ltem NO . Contents Number of Page Page Code 1 Spec Cover11 2 Spec Item 12 3Drawing133Drawing13 4 Antenna Specification14 5 S Parameter 15 6 Passive Test26 ~ 7 7 Radiation Pattern38 ~ 10 8 Antenna Profile111 9 Material Certificate 3412 ~ 45 10 RoHS Test Report **** 11N/AN/AN/A add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen 12--- 13--- Antenna Specification Electrical Properties Frequency 2.4-2.5GHz qy Impedance50 Ohm Nominal V.S.W.R2.0 Max Gain 18dBi Gain 1.8 dBi RadiationOmni-directional PolarizationLinear Physical Properties ConnectorNone Cable TypeO.D.1.13mm Cable Length155mm Cable ColorGray add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen Operating Temp.-40 ~ +85 ̊C Storage Temp / Humidity 25±5 ̊C / <70% AntennaPerformance Test Agilent Antenna Performance Te s t Agilent E5071B SS Parameter Test // BT add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen AntennaPassiveTe s tAntenna PassiveTe s t add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen Passive Test For BT Antenna FreqEffiEffiGain (MHz)(%)(dB)(dBi) 2400 51.5 -2.9 1.6 2410 50.6 -3.0 1.7 2420 49.7 -3.0 1.6 2430 48.4 -3.2 1.4 2440 47.7 -3.2 1.3 2450 51.6 -2.9 1.7 2460 50.7 -3.0 1.7 2470 51.3 -2.9 1.8 2480 50.0 -3.0 1.7 add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen 2490 51.1 -2.9 1.7 2500 50.6 -3.0 1.5 Radiation Pattern For BT Antenna add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen Radiation Pattern For BT Antenna add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen Radiation Pattern For BT Antenna add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen Antenna BT add： 17A-03A, Block B, Nanxian Commercial Plaza, Meilong Road, Longhua New District, Shenzhen PSM-800FSDM-A/SMH-800 ， 安 全 資 料 表 1 版權 2021-01-10 First, chemical products and materials for business Chemical name: PSM-800FSDM-A/SMH-800 liquid solid plate ink Other names: Use and restricted use of construction: flexible printed circuit board (PI/Cu), hand machine roof board Name, address and address of the creator, entrant or supplier: Creator: Yueli Reachability Co., Ltd. Address: No.22 Jingjian Fourth Road, Guanyin District, Taoyuan City: 886-3- 4836651 Urgent/true: 886-3-4836651, true: 886-3-4837487 Second, the hazard identification of resources and materials Hazard classification of chemical products: Health and environmental hazards: Acute toxicity (swallowing) 4, rot/skin irritation 2, heavy weight/eye irritation 2, skin Pass sensitive substance first, carcinogenic substance second, and hazardous substance second (acute toxicity). Indication of content: S y m b o l n u m b e r : Warning language: Warning hazard warning interest: Harmful to swallow Cause skin irritation Causing severe eye irritation may cause skin hypersensitivity and suspected carcinogenesis Toxic to aquatic organisms Hazard prevention measures: Put the container in a place with good ventilation far away from the high temperature Do not eat or drink when using Remove the blindfold/face mask immediately when your clothes are contaminated If you touch your eyes, wash them with plenty of water immediately, and then ask the mud to wear suitable gloves Do not inhale gas/gas/steam gas/gas before use Place it in the upper lock Do not place until you know all safety precautions Avoid releasing release in the environment Other hazards:- III. Composition identification of PSM-800FSDM-A/SMH-800 ， 安 全 資 料 表 2 版權 2021-01-10 capital mixture: Liquid solid plate ink PSM-800FSDM-A/SMH-800 Chemical geology: Chinese and English names of hazardous components Register number of Chemical Digest Service (CAS No.) Degree or degree (percentage of components) Oxygen acrylate oligmer Epoxy acrylate oligmer 28064-14-4 50% Silicon dioxide Fused silica 7631-86-9 13% Aromatic solution 64742-94-5 4% PSM-800FSDM-A/SMH-800 ， 安 全 資 料 表 3 版權 2021-01-10 Methyl dipropylene glycol 34590-94-8 4% Carbon black 1333-86-4 3.5% BaSO4 sulfate 13462-86-7 24% Photoinitiator and the others 5495-84-1 1.5% Fourth, first aid measures First aid methods for the same road: Inhalation: 1. Take self-protection measures before rescue. 2. Remove pollution sources or move patients to new places. 3. If a patient stops breathing, artificial respiration should be given immediately by the person who has been adalmed. If the heart stops, cardiopulmonary resuscitation should be given. When the patient inhales and swallows toxic substances, mouth-to-mouth artificial respiration should be used directly, and pocket masks and other medical equipment should be used for artificial respiration. 4. Maintain the patient's safety and normal temperature. 6. Treat the cure quickly. Pi Mo: Wash the contaminated area with harmonious water for at least 20 minutes, and remove contaminated clothes, shoes and leather products before water. Eye touching: Immediately open the eyelids and wash the contaminated eyes with water for at least 20 minutes, and immediately take care of them. Intake: 1. If the patient will be frustrated, or has been frustrated, he can feed anything. 2. It can induce vomiting and give 240-300ml of water. 3. If you vomit spontaneously, rinse your mouth and supply water repeatedly. The most importa…

Text truncated - open the document above for the full version.

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 36 TEST REPORT Reference No. .................... : WTX24X05111496W001 FCC ID ................................ : 2ASIVPGD768FNU Applicant ........................... : PIN GENIE, INC. DBA LOCKLY Address ............................. : 676 Transfer Rd., St. Paul, MN 55114 Manufacturer ..................... : Smart Electronic Industrial (Dong Guan) Co., Ltd. Address ............................. : Qing Long Road, Long Jian Tian Village, Huang Jiang Town, Dong Guan, Guang Dong, China Product Name ................... : Lockly Guard Fingerprint Deadbolt 728FZ Z-Wave Smart Lock; Lockly Guard Deadbolt 728Z Z-Wave Smart Lock Model No.. .......................... : PGD728F ZU Standards .......................... : FCC Part 15.247 Date of Receipt sample .... : 2024-05-15 Date of Test........................ : 2024-05-15 to 2024-06-12 Date of Issue ..................... : 2024-06-12 Test Report Form No. ....... : WTX_Part 15_247W Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Dashan Chen Jason Su Reference No.: WTX24X05111496W001 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 36 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ......................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................. 5 1.3 TEST METHODOLOGY ........................................................................................................................................... 5 1.4 TEST FACILITY ...................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE .............................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY ............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 11 3. ANTENNA REQUIREMENT ................................................................................................................................. 12 3.1 STANDARD APPLICABLE ..................................................................................................................................... 12 3.2 EVALUATION INFORMATION ................................................................................................................................ 12 4. POWER SPECTRAL DENSITY ........................................................................................................................... 13 4.1 STANDARD APPLICABLE ..................................................................................................................................... 13 4.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 13 4.3 TEST PROCEDURE .............................................................................................................................................. 13 4.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 13 5. DTS BANDWIDTH ................................................................................................................................................. 14 5.1 STANDARD APPLICABLE ..................................................................................................................................... 14 5.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 14 5.3 TEST PROCEDURE .............................................................................................................................................. 14 5.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 14 6. RF OUTPUT POWER ............................................................................................................................................ 15 6.1 STANDARD APPLICABLE .......................................…

Text truncated - open the document above for the full version.