2AXTH-A1Multi - Functional Charging Station

产品规格 USB输入: 5V 3A 9V 3A 手机输出: 15W(最大) 耳机输出: 5W(最大) 手表输出: 3W(最大) 眼镜输出: 5W(最大) 眼镜盒输出: 5W(最大) 手机充电距离: ≤4MM 材质: ABS+PC 五合一 磁吸无线充电器 使用说明书 User Manual Compatible Devices Warnings 1. Input Compatibility: Compatible with QC 2.0/3.0, PD 3.0, and other fast charging protocols. 2. Power Adapter Requirement: Do not use a charger with an output rating lower than 5V/3A. Insufficient power may cause failure to charge multiple devices simultaneously or intermittent charging. It is recommended to use an adapter with an output of 5V/3A, 9V/3A, or higher. 3. Device-Specific Maximum Charging Power: iPhone 12–17 series supports up to 7.5W; Samsung phones support up to 10W; Google phones, general Android models, and Huawei phones support up to 15W. 4. Non-Magnetic Phones: For non-magnetic phones, please attach a magnetic ring before using this product. 5. Physical Handling: Do not excessively squeeze or impact the device. 6. Magnetic Cards: Keep ID cards, bank cards, and other magnetic cards with strips or chips away from the phone 5in1 Charger Station 功能组件 1. 接通电源，给产品通电。 2. 将手机/手表/耳机/眼镜/眼镜盒放到对应的充 电位置，均正常充电。 使用步骤 注意事项 LED 智能指示灯 按键操控 1. 输入兼容：QC 2.0/3.0、PD 3.0等快充协议 2. 请勿使用输出规格低于5V/3A的充电头，功率不足 会出现无法同时充电或断充问题，建议搭配5V/3A 9V/3A 以上规格适配器进行供电。 3. iPhone 12-17系列最大充电功率7.5W；三星手机 最大充电功率10W；谷歌手机、安卓通用机型、华为 手机最高支持15W。 4. 非磁吸手机，请加装引磁环后再使用本产品。 5. 请勿过度挤压、撞击本设备。 6. 请勿将身份证、银行卡等带磁条/芯片的磁卡靠近 手机充电区域，避免磁卡消磁失效。 7. 充电区域严禁放置金属异物；手机请勿使用全包 金属壳、内置金属配件的保护壳，金属材质会阻隔 无线充电信号，造成充电异常、无法充电。 适用设备 1. 智能手机：iPhone 12～17全系列。（三星手机、谷 歌手机、通用安卓手机、华为手机需自带无线充电功 能方可使用，并佩戴磁吸手机壳） 2. 智能手表:Apple Watch全系列，支持无线磁吸充 电 3. 智能耳机: AirPods 3 MagSafe 版、AirPods Pro 手机无线 充电区域 耳机无线 充电区域 手表无线 充电区域 手表无线 充电区域 眼镜充电位 眼镜盒充电位 USB-C接口 加减按键 “-”按键“+”按键 功能按键 功能按键 显示屏 防滑垫 模式 通电时钟常亮,充电指示灯5S熄灭 功能 双击功能键 12、24小时制切换 （12小时制显示AM或PM， 两个都不显示是24小时制） 关闭/打开显示屏 （关屏后时钟功能正常） 长按2S 功能键 *注： 断电后时钟复位需重新设置时间 *Note: Clock resets after power cut, please reset time again. 单击功能键 分钟数字个位闪烁，单击“＋－”键 调整数字，可长按快速调整数字， 确认数字后再次单击进入时钟调整 单击功能键 两次 时钟数字个位闪烁，单击“＋－”键 调整数字，可长按快速调整数字， 确认数字后再次单击保存时间 模式 通电 待机 充电 检测到异物 时钟常亮,充电指示灯5S熄灭 时钟常亮 手机充电指示灯常亮5秒熄灭 无 眼镜充电指示灯常亮5秒熄灭 眼镜盒充电指示灯常亮5秒熄灭 手机充电位指示灯闪烁提醒， 耳机手表无指示灯 （眼镜+眼镜盒无此功能） 屏幕指示灯 充满 Touch Buttons ModeFunctions Mode Powered Standby Wireless Charging FOD Full Charged Magnetic Phone Charging Pad Anti-Slip Mat USB-C Power Input Port 1 × 5-in-1 Magnetic Wireless Charger 1 × QC3.0 Power Adapter 1 × USB-C Charging Cable 2 × Power Conversion Plugs 1 × User Manual Input: 5V 2A 9V 2A Phone Output: 15W (Max) Earbuds Output: 5W (Max) Watch Output: 3W (Max) Glasses Output: 5W (Max) Glasses Case Output: 5W (Max) Phone Charging Distance≤4MM Materials: ABS+PC 1. Connect the charger to power outlet. 2. Put devices on matched slots, auto charging starts. 1. Smartphones: iPhone 12–17 full series. (Samsung, Google, general Android, and Huawei phones must have built-in wireless charging capability and be used with a magnetic phone case.) Glasses Case Charging Slot Smart Glasses Charging Slot Time Adjust Buttons (+/-) Mode & Time Setting Button Digital Clock Display Powered Clock turned on; Light turns off after 5 seconds. Double-click the function button 12/24-Hour Mode Switch (In 12-hour mode, "AM" or "PM" is shown; when neither appears, the clock is in 24-hour mode.) Press and hold the function button for 2 seconds. Long press: Turn screen on/off. Clock keeps working. Press the function button once. The units digit of the minutes flashes. Press "+" or "‒" to adjust the number (long press for fast adjustment). Press the function button again to enter clock adjustment. Press the function button twice. The units digit of the hour flashes. Press "+" or "‒" to adjust the number (long press for fast adjustment). Press the function button again to save the time. Clock turned on; Light turns off after 5 seconds. Clock always on Phone charging indicator lights up for 5 seconds then turns off. Smart glasses charging indicator lights up for 5 seconds then turns off. Smart glasses case charging indicator lights up for 5 seconds then turns off. Charging indicator on the phone charging pad blinks as a reminder. No indicators for earbuds or watch. (Not available for glasses or glasses case.) Screen Indicator Light No light when fully charged Product Specs Package Contents FCC Statement How to Use LED Status Light 有问题请联系我们！ Functional component “-”Button“+”Button Function Button For questions, please contact us Warranty Warranty After-Sales Service The warranty period of this product is 24 months. From the date of purchase, you'll enjoy a free warranty within the warranty period with valid documents. Note: The following conditions are not covered by the warranty: 1. Unable to provide formal purchase certificate. 2. Damage caused by man-made or irresistible factors. 3. Accidental damage. (Misuse, abuse or neglect) 4. lmproper repair or alteration by unauthorized persons. 5. Operation without following the manual's instructions. * The company reserves the right to make the final interpretation of the above-mentioned after-sales terms and restrictions. If you have any questions or concerns, feel free to contact us via Amazon: 1. Go to your "Orders". 2. Find your order in the list. 3. Click "Get help with order". 4. Select the problem with your order. 5. Choose the "Subject" from the displayed list. 6. Contact the seller. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio Made in China frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to r…

Text truncated - open the document above for the full version.

1/1 FCC US Agent, LLC LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Telephone No: 708-571-3148 Email: [email protected] Applicant: Company name: Shenzhen Caibo Technology Co., Ltd. Product Description: Multi - Functional Charging Station Grantee code: 2AXTH FCC ID: 2AXTH-A1 FRN： 0030078273 Contact Name: Linjun Hu Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Telephone No: 13713719057 Email: [email protected] [Shenzhen Caibo Technology Co., Ltd.] certifies that, as of the date of this filing of the application with the TCB, [FCC US Agent, LLC] is our designated US agent for service of process for the above referenced FCC ID. [Shenzhen Caibo Technology Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2026/09/02 Applicant’s Name: Lin jun Hu US Agent’s Name: Tim Payne Title: CEO Title: Signature Signature

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Multi - Functional Charging Station Grantee code: 2AXTH FCC ID: 2AXTH-A1 FRN: 0030078273 Contact Name: Linjun Hu Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Telephone No: 13713719057 Fax No: / Email: [email protected] i. [Shenzhen Caibo Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Shenzhen Caibo Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Shenzhen Caibo Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment. Date: 2026-07-21 Applicant’s Name: Linjun Hu Title: CEO Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1

Shenzhen Caibo Technology Co., Ltd. Code 00018768 Ed. 1 Item 1. The device is able to install software/program installation? ☐ Yes, go to Item 2. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A Device Multi - Functional Charging Station Company name Shenzhen Caibo Technology Co., Ltd. Grantee code 2AXTH FCC ID 2AXTH-A1 FRN 0030078273 Contact name Linjun Hu Address F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao'an District, Shenzhen, China Telephone number 13713719057 E-mail [email protected] Chipset/module information IP6862, MCU-24 Operating System (if applicable) N/A Storage Capacity (hard drive or other permanent memory storage, if applicable) N/A 2 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A # General Requirements (For Linux system) Yes / No or N/A Comments 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher N/A 3 3 RAM: 1 GB N/A 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; N/A After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐ Yes, go to Item 3. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software Item 3. Connectivity Capabilities: # Physical Interface Purpose Justification 1 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications. 4 1 # Wireless Interface Purpose Justification 1 1 After the review of this items, the device: ☒ Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐ Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third- party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature: Name: Linjun Hu Date: 28/07/2026

TCB CALL página 1 File FCC ID: 2AXTH-A1 Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○ We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. On the official register from : https://opencorporates.com/companies/us_il/LLC_12842678 In google: TCB CALL página 2 Bank information TCB CALL página 3 TCB CALL página 4 TCB CALL página 5 TCB CALL página 6 TCB CALL página 7 TCB CALL página 8 TCB CALL página 9 ► CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "C5266091_X23_Ed1_US_Agent_Letter" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "C5266091_X23_Ed1_US_Agent_Letter" >

C5266091_X10_Ed.2 1/1 Shenzhen Caibo Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AXTH-A1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Linjun Hu Title: CEO

Shenzhen Caibo Technology Co., Ltd. C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Caibo Technology Co., Ltd. Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Product Name: Multi - Functional Charging Station Model Number: A1, AG16, AG17, AG18 FCC Identifier: 2AXTH-A1 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Linjun Hu Date: 27/07/2026 Title: CEO Signature of applicant:

Report No. ITA26B07001391W Page 1 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001391W Page 2 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001391W Page 3 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001391W Page 4 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view

FCC ID: 2AXTH-A1

Report No. ITA26B07001391W Page 1 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Internal view Details of:Internal view Report No. ITA26B07001391W Page 2 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Internal view Details of:Internal view Report No. ITA26B07001391W Page 3 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Internal view Details of:WPT antenna for watch view Report No. ITA26B07001391W Page 4 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:WPT antenna for phone view Details of:WPT antenna for earphone view Report No. ITA26B07001391W Page 5 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:PCB view Details of:PCB view Report No. ITA26B07001391W Page 6 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:PCB view Details of:PCB view Report No. ITA26B07001391W Page 7 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:PCB view Details of:PCB view

Test Report issued under the responsibility of: Itestek Testing Co., Ltd. (Dongguan) TEST REPORT RADIO FREQUENCY FOR WIRELESS POWER TRANSFER Report Number.............................:ITA26B07001391W 002 Sample date..................................:2026-07-17 Test date .......................................:2026-07-17 to 2026-08-21 Issue date .....................................:2026-08-21 Total number of pages ................:9 Standard/According to ...............:KDB 680106 D01 Wireless Power Transfer v04 Template version .........................:V2.0 Testing Laboratory ......................:Itestek Testing Co., Ltd. (Dongguan) Address ........................................:Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Tested by ......................................:Tom Zhang Checked by...................................:Oliver Qiao Approved by .................................:Joker Qi Applicant’s name .........................:Shenzhen Caibo Technology Co., Ltd. Address ........................................:F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao'an District, Shenzhen, China Manufacturer’s name...................:Same as applicant Address ........................................:Same as applicant Factory’s name ............................:Same as applicant Address ........................................:Same as applicant Trade Mark....................................:GEEKERA Product description .....................:Multi - Functional Charging Station Model/Type reference ..................:A1, AG16, AG17, AG18 Ratings..........................................:Input: 5Vdc, 3A; 9Vdc, 3A Output: Wireless charging of Phone: 15W (max) Wireless charging of Watch: 3W (max) Wireless charging of Earphone: 5W (max) Glasses output: 5W (max) Glasses Case output: 5W (max) FCC ID ...........................................:2AXTH-A1 Test result.....................................:Pass Report No.:ITA26B07001391W 002Page 2 of 9 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Declare: 1. This report shall not be partially reproduced without the consent of the laboratory. 2. If the report without tester's signature, auditor's signature, approver's signature and inspection seal, the report is invalid. 3. The test results are valid only for the tested samples. 4. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above relevant standards. 5. If the report is not stamped with the accreditation recognized seal, it will only be used for scientific research, education, and internal quality control activities, and is not used for the purpose of issuing supporting data to the society. Testing laboratory: Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China FCC designation number CN1436 A2LA has accredited, certificate Number 7609.01 Report No.:ITA26B07001391W 002Page 3 of 9 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 1. General test information 1.1.Description of EUT Details of technical specification refer to the description in follows: Test model numberA1 Test sample numberA-001 Model differentAll models are identical, except model number Frequency range (Hz) 110.1K-205K Hz: output power 5W, 7.5W, 10W, 15W for phone 110.1K-205K Hz: output power 5W for earphone 300K-350K Hz: output power 3W for watch Modulation techniqueASK Antenna typeCoil Antenna Antenna gain0 dBi Temperature range (°C)-20 ~ 50 Hardware versionV1.0 Software versionV1.0 Block diagram EUT configuration for test EUT/AEAC Mains 1.2.Test modes ModeTest Status 1 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 3W (300K-350KHz) + Glasses output: 5W (max) + Glasses Case output: 5W (max) 2 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 7.5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 3W (300K-350KHz) + Glasses output: 5W (max) + Glasses Case output: 5W (max) 3 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 10W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 3W (300K-350KHz) + Glasses output: 5W (max) + Glasses Case output: 5W (max) 4 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 15W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Report No.:ITA26B07001391W 002Page 4 of 9 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Wireless charging of watch for output 3W (300K-350KHz) + Glasses output: 5W (max) + Glasses Case output: 5W (max) 5 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Glasses output: 5W (max) + Glasses Case output: 5W (max) 6 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 7.5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Glasses output: 5W (max) + Glasses Case outp…

Text truncated - open the document above for the full version.

Test Report issued under the responsibility of: Itestek Testing Co., Ltd. (Dongguan) TEST REPORT FEDERAL COMMUNICATIONS COMMISSION FOR WIRELESS POWER TRANSFER Report Number.............................:ITA26B07001391W 001 Sample date..................................:2026-07-17 Test date .......................................:2026-07-17 to 2026-08-21 Issue date .....................................:2026-08-21 Total number of pages ................:18 Standard/According to ...............:FCC CFR Title 47 Part 15 Subpart C (ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a- 2024) Template version .........................:V2.0 Testing Laboratory ......................:Itestek Testing Co., Ltd. (Dongguan) Address ........................................:Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Tested by ......................................:Tom Zhang Checked by...................................:Oliver Qiao Approved by .................................:Joker Qi Applicant’s name .........................:Shenzhen Caibo Technology Co., Ltd. Address ........................................:F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao'an District, Shenzhen, China Manufacturer’s name...................:Same as applicant Address ........................................:Same as applicant Factory’s name ............................:Same as applicant Address ........................................:Same as applicant Trade Mark....................................:GEEKERA Product description .....................:Multi - Functional Charging Station Model/Type reference ..................:A1, AG16, AG17, AG18 Ratings..........................................:Input: 5Vdc, 3A; 9Vdc, 3A Output: Wireless charging of Phone: 15W (max) Wireless charging of Watch: 3W (max) Wireless charging of Earphone: 5W (max) Glasses output: 5W (max) Glasses Case output…

Text truncated - open the document above for the full version.