2AXTH-MG17Magnetic wireless charger

包 装 为了您的权益，请您认真填写，并妥善保管，作为维前凭证！ 请勿擅自修改内容，否则视为作废。 本公司保留对该产品售后服务条例的最终解释权。 本产品三包有效期：自购买日起（以寄回的客户回执或购机发票 日期为准），提供12个月保修服务，其它附件（如包装等）不属 三包范围，产品外观为人为损坏，附件损失，不在三包之列。不 在三包之内或超过三包期的产品，客户仍享受维修服务，但需要 交纳维修工本费。 保 修 产品规格 注意事项 MG17 使用说明书 功能组件 1.智能手机非磁吸手机，请增加引磁环后使用该产品。 2.请勿过度挤压或碰撞设备。 3. 请勿与带磁条或者芯片的磁卡（身份证、银行卡等）放置 太近,避免造成磁卡失效。 磁吸无线充*1 磁吸桌面支架*1 C-C 充电线*1 说明书*1 产品名称：MG17 输入电压：5V-3A/9V-3A/12V-3A/15V-3A 输出功率：5W/7.5W/10W/15W/25W工 作温度: -10～40°C 工作频率：110.1K-205KHz 360KHz 充电距离：≤4mm 磁铁吸力：1.6KG 产品保修卡 USER MANUAL 1. For smartphones that are not magnetic, please add a magnetic ring before using this product. 2. Do not over squeeze or collide with the equipment. 3. Please do not place it too close to the magnetic card (ID card, bank card, etc.) with magnetic stripe or chip to avoid magnetic card failure. Wireless charger*1 C-C cable*1 User manual*1 Model：MG17 Input：5V-3A/9V-3A/12V-3A/15V-3A Output power：5W/7.5W/10W/15W/25W Working temperature: -1040 Charging frequency：110.1K-205KHz 360KHz Induction distance：≤4mm Magnetic attraction：1.6KG Functional component 1 2 3 Wireless Charging Area Charging indicator light C-C interface Heat Dispatch Hole Lighting mode Caution Product specification Package Warranty For your rights and interests, please fill in carefully and keep it properly as a pre maintenance voucher! Do not modify the content without authorization, otherwise it will be deemed invalid. The company reserves the final right to interpret the after-sales service regulations of the product. Product Warranty Card The three guarantee period of this product: from purchasing date (Prevail to the customer receipt date or invoice date), provide 12 months guarantee. product surface man-made damage,accessories missed are not include in this guarantee, repair service for the product is out of the guarantee period or not covered by warranty ,customer need to pay the repair charge. 性能概述 1、本产品最大充电功率为25W，充电效率根据充电环境和手机会 有所不同。 2、制冷与风扇同时运行时，充电区域温度降低，为手机高效降 温；散热扇将半导体运行产生的热量向外排出，机器背面温度 微微升高属正常现象。 3、无线充的最佳距离是4mm以内并不能穿透金属，所以需要 避免用金属的或太厚的（大于4mm）手机保护壳，这样才能 保证手机快速的无线充电。 4、如果手机不支持无线充电或者检测到金属异物，红色指示灯 闪烁5秒后灯灭。 5、从产品上取下手机后，指示灯即刻常亮待机状态。停车熄火, 产品停止供电时，指示灯熄灭，手机依旧被磁力吸附在产品上, 可随时取下。 LED 智能指示灯 模式 通电 待机 充电 检测到异物 LED灯常亮 LED灯常亮 LED灯熄灭，风扇工作 LED灯快闪5S熄灭,风扇停止 指示灯 充满LED灯熄灭，风扇停止工作 Standby Charging Foreign Object Detected LED Light Stays On LED Light Stays On LED Light Off, Fan Operating The LED light flashes quickly for 5 seconds and turn off, but recovers after removing foreign objects Full chargeLED Light Off, Fan Stopped ModeIndicator light Power on 1.The maximum charging power of this product is 25W, and the charging efficiency may vary depending on the charging environment and the phone. 2. When the cooling and fan are running simultaneously, the temperature in the charging area decreases, which efficiently cools down the phone; It is normal for the temperature on the back of the machine to slightly increase ,when the heat generated by the operation of the semiconductor and discharged outward by the cooling fan. 3. The best distance of wireless charging is within 4mm, and it cannot penetrate metal, so it is necessary to avoid using metal or too thick (over 4mm) mobile phone case, so as to ensure fast wireless charging of mobile phone. 4. If the phone does not support wireless charging or detects a metal object, the red indicator light will flash for 5 seconds before turning off. 5. After the phone is removed from the product, the indicator will immediately show the standby status. When the car engined off and the power supply stops, the indicator light goes off. The mobile phone is still attached to the product by magnetic force and can be taken off at any time. Performance Overview MG17 1 4 3 5 2 MG17 手机无线充电区域 散热孔 1 2 C -C 接口 充电指示灯 4 3 风扇开关按键 5 按键操控 模式 单击充电状态下单击可打开/关闭风扇 关闭/打开灯光 双击 功能 1 4 3 5 2 MG17 4 Fan switch button 5 Touching button functions Mode Single clickWhen charging, single-click to turn the fan on/off. T urn the light off/on. Functions Double click FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. I f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).

1/1 FCC US Agent, LLC LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Telephone No: 708-571-3148 Email: [email protected] Applicant: Company name: Shenzhen Caibo Technology Co., Ltd. Product Description: Magnetic wireless charger Grantee code: 2AXTH FCC ID: 2AXTH-MG17 FRN： 0030078273 Contact Name: Linjun Hu Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Telephone No: 13713719057 Email: [email protected] [Shenzhen Caibo Technology Co., Ltd.] certifies that, as of the date of this filing of the application with the TCB, [FCC US Agent, LLC] is our designated US agent for service of process for the above referenced FCC ID. [Shenzhen Caibo Technology Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2026/09/02 Applicant’s Name: Lin jun Hu US Agent’s Name: Tim Payne Title: CEO Title: Signature Signature

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Magnetic wireless charger Grantee code: 2AXTH FCC ID: 2AXTH-MG17 FRN: 0030078273 Contact Name: Linjun Hu Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Telephone No: 13713719057 Fax No: / Email: [email protected] i. [Shenzhen Caibo Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Shenzhen Caibo Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Shenzhen Caibo Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment. Date: 2026-07-27 Applicant’s Name: Linjun Hu Title: CEO Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

Shenzhen Caibo Technology Co., Ltd. Code 00018768 Ed. 1 Item 1. The device is able to install software/program installation? ☐ Yes, go to Item 2. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A Device Magnetic wireless charger Company name Shenzhen Caibo Technology Co., Ltd. Grantee code 2AXTH FCC ID 2AXTH-MG17 FRN 0030078273 Contact name Linjun Hu Address F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao'an District, Shenzhen, China Telephone number 13713719057 E-mail [email protected] Chipset/module information IP6862 Operating System (if applicable) N/A Storage Capacity (hard drive or other permanent memory storage, if applicable) N/A 2 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A # General Requirements (For Linux system) Yes / No or N/A Comments 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher N/A 3 3 RAM: 1 GB N/A 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; N/A After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐ Yes, go to Item 3. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software Item 3. Connectivity Capabilities: # Physical Interface Purpose Justification 1 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications. 4 1 # Wireless Interface Purpose Justification 1 1 After the review of this items, the device: ☒ Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐ Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third- party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature: Name: Linjun Hu Date: 28/07/2026

TCB CALL página 1 File FCC ID: 2AXTH-MG 17 Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. On the official register from : https://opencorporates.com/companies/us_il/LLC_12842678 In google: TCB CALL página 2 Bank information TCB CALL página 3 TCB CALL página 4 TCB CALL página 5 TCB CALL página 6 TCB CALL página 7 TCB CALL página 8 TCB CALL página 9 ►CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "C5266091_X23_Ed1_US_Agent_Letter" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "C5266091_X23_Ed1_US_Agent_Letter" >

C5266091_X10_Ed.2 1/1 Shenzhen Caibo Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AXTH-MG17 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Linjun Hu Title: CEO

Shenzhen Caibo Technology Co., Ltd. C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Caibo Technology Co., Ltd. Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Product Name: Magnetic wireless charger Model Number: MG17, VDT-AL2B, ED74, T238-G FCC Identifier: 2AXTH-MG17 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Linjun Hu Date: 27/07/2026 Title: CEO Signature of applicant:

Report No. ITA26B07001395WPage 1 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001395WPage 2 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001395WPage 3 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001395WPage 4 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view

FCC ID: 2AXTH-MG17

Report No. ITA26B07001395WPage 1 of 2 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Internal view Details of:WPT antenna view Report No. ITA26B07001395WPage 2 of 2 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:PCB view Details of:PCB view

Test Report issued under the responsibility of: Itestek Testing Co., Ltd. (Dongguan) TEST REPORT RADIO FREQUENCY FOR WIRELESS POWER TRANSFER Report Number.............................:ITA26B07001395W 002 Sample date..................................:2026-07-17 Test date .......................................:2026-07-17 to 2026-08-21 Issue date .....................................:2026-08-21 Total number of pages ................:7 Standard/According to ...............:KDB 680106 D01 Wireless Power Transfer v04 Template version .........................:V2.0 Testing Laboratory ......................:Itestek Testing Co., Ltd. (Dongguan) Address ........................................:Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Tested by ......................................:Tom Zhang Checked by...................................:Oliver Qiao Approved by .................................:Joker Qi Applicant’s name .........................:Shenzhen Caibo Technology Co., Ltd. Address ........................................:F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Manufacturer’s name...................:Same as applicant Address ........................................:Same as applicant Factory’s name ............................:Same as applicant Address ........................................:Same as applicant Trade Mark....................................:/ Product description .....................:Magnetic wireless charger Model/Type reference ..................:MG17, VDT-AL2B, ED74, T238-G Ratings..........................................:Input: 5Vdc, 3A; 9Vdc, 3A; 12Vdc, 3A; 15Vdc, 3A Wireless charging output: 5W, 7.5W, 10W, 15W, 25W FCC ID ...........................................:2AXTH-MG17 Test result.....................................:Pass Report No.:ITA26B07001395W 002Page 2 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Declare: 1. This report shall not be partially reproduced without the consent of the laboratory. 2. If the report without tester's signature, auditor's signature, approver's signature and inspection seal, the report is invalid. 3. The test results are valid only for the tested samples. 4. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above relevant standards. 5. If the report is not stamped with the accreditation recognized seal, it will only be used for scientific research, education, and internal quality control activities, and is not used for the purpose of issuing supporting data to the society. Testing laboratory: Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China FCC designation number CN1436 A2LA has accredited, certificate Number 7609.01 Report No.:ITA26B07001395W 002Page 3 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 1. General test information 1.1.Description of EUT Details of technical specification refer to the description in follows: Test model numberMG17 Test sample numberA-001 Model differentAll models are identical, except model number Frequency range (Hz) 110.1K-205K Hz: output power 5W, 7.5W, 10W; 360K Hz: output power 15W, 25W Modulation techniqueASK Antenna typeCoil Antenna Antenna gain0 dBi Temperature range (°C)-10 ~40 Hardware versionV1.0 Software versionV1.0 Block diagram EUT configuration for test EUT/AEAC Mains 1.2.Test modes ModeTest Status 1 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) 2 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 7.5W (110.1K-205KHz) 3 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 10W (110.1K-205KHz) 4 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 15W (360KHz) 5 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 25W (360KHz) 6AC Mains (120Vac, 60Hz) + Standby mode Remark: The aforementioned testing modes were all conducted under battery Status ≤1% (full load), battery Status ≈50% (half load), and battery Status ≥99% (no load) conditions. After testing, it was found that the test data under battery Status ≤1% (full load) condition is the worst- case. The report reflecting only the worst-case test data. Report No.:ITA26B07001395W 002Page 4 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 1.3.Test environment conditions During the measurement the environmental conditions were within the listed ranges: Temperature range (°C)15-35 Humidity range (%)30-75 Pressure range (kPa)85-105 1.4.Test environment conditions ItemEquipmentMfr/BrandModel / TypeSeries No.Note 1LoadAppleIphone 17-- Wireless charging of phone: 5W, 7.5W, 15W, 25W 2LoadYBT P V3.1- Qi2.2/MPP -- Wireless charging of phone: 5W, 7.5W, 10W, 15W, 25W 3 XIAOMI Charge XIAOMIMDY-14-ED-- Input: 100-240Vac, 50/60Hz, 3.0A Output: USB-C1/C2/C3 5Vdc, 3A; 9Vdc, 3A; 15Vdc, 3A; 11Vdc, 6.1A; 20Vdc, 5A; 20Vdc, 6A USB-A 5Vdc, 3A; 9Vdc, 3A; 12Vdc, 2.25A Remark: The test utilized XIAOMI Charge and the input voltage of XIAOMI Charge was 120Vac, 60Hz. Report No.:ITA26B07001395W 002Page 5 of 7 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Buildin…

Text truncated - open the document above for the full version.

Test Report issued under the responsibility of: Itestek Testing Co., Ltd. (Dongguan) TEST REPORT FEDERAL COMMUNICATIONS COMMISSION FOR WIRELESS POWER TRANSFER Report Number.............................:ITA26B07001395W 001 Sample date..................................:2026-07-17 Test date .......................................:2026-07-17 to 2026-08-21 Issue date .....................................:2026-08-21 Total number of pages ................:19 Standard/According to ...............:FCC CFR Title 47 Part 15 Subpart C (ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a- 2024) Template version .........................:V2.0 Testing Laboratory ......................:Itestek Testing Co., Ltd. (Dongguan) Address ........................................:Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Tested by ......................................:Tom Zhang Checked by...................................:Oliver Qiao Approved by .................................:Joker Qi Applicant’s name .........................:Shenzhen Caibo Technology Co., Ltd. Address ........................................:F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Manufacturer’s name...................:Same as applicant Address ........................................:Same as applicant Factory’s name ............................:Same as applicant Address ........................................:Same as applicant Trade Mark....................................:/ Product description .....................:Magnetic wireless charger Model/Type reference ..................:MG17, VDT-AL2B, ED74, T238-G Ratings..........................................:Input: 5Vdc, 3A; 9Vdc, 3A; 12Vdc, 3A; 15Vdc, 3A Wireless charging output: 5W, 7.5W, 10W, 15W, 25W FCC ID ...........................................:2AXTH-MG17 Test result.....................................:Pass Report No.:ITA26B07001395W 001Page 2 of 19 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Declare: 1. This report shall not be partially reproduced without the consent of the laboratory. 2. If the report without tester's signature, auditor's signature, approver's signature and inspection seal, the report is invalid. 3. The test results are valid only for the tested samples. 4. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above relevant standards. 5. If the report is not stamped with the accreditation recognized seal, it will only be used for scientific research, education, and internal quality control activities, and is not used for the purpose of issuing supporting data to the society. Testing laboratory: Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China FCC designation number CN1436 A2LA has accredited, certificate Number 7609.01 1. Summary of test results RequirementCFR47 SectionResult Antenna requirement§15.203Pass AC Power Line Conducted Emission §15.207 Pass Spurious Emission§15.209Pass Occupied Bandwidth§15.215(c)Pass Report No.:ITA26B07001395W 001Page 3 of 19 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 2. General test information 2.1.Description of EUT Details of technical specification refer to the description in follows: Test model numberMG17 Test sample numberA-…

Text truncated - open the document above for the full version.