2AXTH-T164-in-1 Magnetic Wireless Charger

1. Connect the power supply and power up the product. 2. Place the phone/earphone/watch in the corresponding charging position and charge it normally. Package Functional component Use stepsWarranty Input: 9V-3A / 12V-3A / 15V-3A / 20V-3A Phone Output: 5W / 7.5W / 10W / 15W / 25W Earphone Output: 5W Watch Output: 2.5W (Apple / Samsung) Fan Power: Approx. 1W (5000 RPM) Cooling Power: 7W / 15W Phone Charging Distance: ≤ 4mm Frequency: 2.5W (326.5 kHz); 5W, 7.5W, 10W (110–205 kHz); MPP 15W / 25W (360 kHz) Input Port: USB-C Magnetic Force: 0.8 kg Size : 111mm × 145mm × 160mm Phone Adjust Angle: 90° Product specification For your rights and interests, please fill in carefully and keep it properly as a pre maintenance voucher! Do not modify the content without authorization, otherwise it will be deemed invalid. The company reserves the final right to interpret the after-sales service regulations of the product. Product Warranty Card 1. Smartphones: Compatible with iPhone 12 to 17 series and subsequent models, and all phones supporting Qi wireless charging protocol 2. Earphones: Compatible with Apple AirPods, Samsung earphones and other Qi-certified charging devices 3. Smart Watches: Compatible with Apple Watch and Samsung smart watches Applicable Devices 5V power supply is not applicable. - It is recommended to use adapters of 9V/3A and above. Max 25W charging power for single phone with input over 12V/3A. Simultaneous charging power: 25W for phone, 5W for earphone, 2.5W for watch with input over 20V/3A. To activate full power mode with semiconductor cooling and 25W fast charging, please use a 20V/3A adapter rated 60W or higher. The maximum output of QC adapter is 18W. 45W PD adapter only supports 7W cooling power. - The cooling function cannot be activated when input power is lower than 45W. 60W PD adapter supports full-power 3-in-1 charging, with 7W and 15W adjustable cooling levels. Power Supply & Power Parameters Caution 1. Please use the original iphone 12~17 phone case or take off the phone case to use 2. For non-MagSafe phones, please use anextra magnetic ring or MagSafe case to use this product 3. Do not excessively squeeze or bump the device. 4. Please do not place it too close to magnetic cards with magnetic stripes/chips (ID cards, bank cards, etc.) to avoid causing the magnetic cards to fail. 5.Please do not use thick phone cases/magnetic rings, which will affect the magnetic force and normal charging 6.Do not use a 5V power adapter, as it will prevent the device from charging properly. Please use a power adapter with an output voltage of 9V or higher The three guarantee period of this product: from purchasing date (Prevail to the customer receipt date or invoice date), provide 12 months guarantee. product surface man-made damage,accessories missed are not include in this guarantee, repair service for the product is out of the guarantee period or not covered by warranty ,customer need to pay the repair charge. LED intelligent indicator Touching button functions Mode Single click Long press Night light (cool light → warm light → off, cycle repeatedly) Adjust night light brightness (bright → dim, cycle repeatedly) Functions ModeFunctions Double click Adjust cooling power 7W cooling: LED indicator shows green 15W cooling: LED indicator shows red Cooling off: LED indicator shows ice blue Cycle mode: 7W → 15W → off. No memory function after power restart. Mode Power-on Standby Charging Metal foreign object detection Ice blue light light stays on for 30s Ice blue light turns off Corresponding colored light breathes for 30 seconds then turns off, cooling fan works Red light flashes rapidly continuously, fan stops operation; function recovers after removing foreign object *No indicator prompt for earphone and watch charging Indicator Light Full ChargedLED light off, cooling fan stops Touch switch (TEC Cooling + Desk Lamp) Mobile phone Wireless Charging Area Earphone charging area Earphone charging area Watch Wireless Charging Area Anti-slip mat Type-C interface Desk Lamp TEC Cooling 4-in-1 Magnetic Wireless Charger *1 Type-C charging cable*1 User Manual *1 4-in-1 Magnetic Wireless Charger USER MANUAL FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installat…

Text truncated - open the document above for the full version.

4-in-1 Magnetic Wireless Charger Model: T16 Input: 9V 3A,12V 3A,15V 3A,20V 3A Phone Output: 5W/7.5W/10W/25W Apple Watch Output: 2.5W AirPods Output: 5W Made in china type-c朝向 镭雕灰色：PANTONE 冷灰8C 耳机充-底壳 FCC ID: 2AXTH-T16 Label and Label location

Report No. ITA26B07001401WPage 1 of 2 It estek Testing Co., Ltd . (Dongguan) Room 116, Build ing 8 and Room 606, Building 3, Innovation Port of H anyuwan, Li yu an R oad, Tangwei, Fuhai Subdist rict, Bao'an Distri ct, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Conducted emission test view Details of:Radia ted emission test (30M-1G Hz) view Report No. ITA26B07001401WPage 2 of 2 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Radiated emission test (9K-30M Hz) view Details of:RF exposure test view

惠州启泰电子科技有限公司 HuizhouQitaiElectronicTechnologyCo.,LTD SPECIFICATIONSSHEET CUSTOMER: 客户 DESCRIPTION: 品名描述 CUSTOMERP/N: 客户品名 PARTNUMBER: 制造商料号 DATEOFAPPLICATION: 提出日期 中利冠达 ZLGD-A1-0485 2025-5-7 CLASSIFICATIONOFSPEC.PRESENTATION.(Ticktherelevantbox"√") oNewapplication新规格 √Newpartisaddedtoacceptedspecification新产品规格追加记录 oRevisionofacceptedspecification既存规格图面变更 ACCEPTANCESTAMP() APPROVALBY 承认 CHECKBY 审查 PREPAREBY 制作 ADDRESS:3rdFloor,No.181,Mingyue2ndRoad,ShiwanTown,BoluoCounty,Huizhoucity TELPHONE:0752-6668681 E-MAIL:[email protected] 惠州启泰电子科技有限公司 HuizhouQitaiElectronicTechnologyCo.,LTD HistoryForRevisedSpecification CUSTOMERP/N: 客户品名 中利冠达 PARTNUMBER: 制造商料号 ZLGD-A1-0485 Item 项次 DESCRIPTION(ContentOrReasonForChanged) 变更内容 Rev. 版本 CustRev. 客户版本 Date 日期 Revisor 修订者 1 InitialRelease(初版发行) A0 2025-5-7 冯欣 APPROVEDBY 承认 CHECKEDBY 审查 PREPAREDBY 制作 DATE 日期 PAGE 页码 晁子奇 冯欣 2025-5-7 1of3 惠州启泰电子科技有限公司 HuizhouQitaiElectronicTechnologyCo.,LTD Specification 规格内容 CUSTOMERP/N: 客户品名 中利冠达 PARTNUMBER: 制造商料号 ZLGD-A1-0485 1.DIMENSIONS():(Unit:mm) 单位（Unit）：毫米（mm） ABCDEF 21Max 14.5±0.57.5±0.545±242±326±1 1.该产品不贴背胶。 2.磁铁规格：φ7.5*4，磁场（4600GS±150GS）（磁铁不组装）。 3.软磁出线处开线槽。 APPROVEDBY 承认 CHECKEDBY 审查 PREPAREDBY 制作 DATE 日期 PAGE 页码 2025-5-7 2of3 惠州启泰电子科技有限公司 HuizhouQitaiElectronicTechnologyCo.,LTD Specification 规格内容 CUSTOMERP/N: 客户品名 中利冠达 PARTNUMBER: 制造商料号 ZLGD-A1-0485 2.WINDINGDETAILS(绕线详细说明) Coil1 圈数 Turns 线径 WireDia 绕线方式疏/密 Wdg.Type Spred/Close 绕线方向 Wdg.Direction 相交是/否 Intersect Yes/Not 13TS 0.08*24P热风绞线(HotAir strandedWire) 密绕（Close） 逆绕 是（Yes） 3.电气特性（ELECTRICALCHARACTERISTICS）: 温度TEMPERATURE:25±10,RELATIVEHUMIDITY:6510% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TESTFREQUENCY 测试仪器 TESTEQUIPMENTS Coil1 1. INDS-F 7.5uh-8.1uh 100kHz/VUC2906A 2.QS-F 20Min 100kHz/VUC2906A 3. DCRS-F 140Max 100kHz/VUC2906A APPROVEDBY 承认 CHECKEDBY 审查 PREPAREDBY 制作 DATE 日期 PAGE 页码 2025-5-7 3of3

Page1of 5 东莞市德弗力五金电子材料有限公司 产品规格书 PRODUCT SPECIFICATION 客 户： CUSTOMER:____________________________________________________________________ 客户料号： CUST P/N:____________________________________________________________________ 德弗力料号： K C P/N:____________________________________________________________________ 产品઻号： 22.0 39 80 0.08mm 80P 11TS D E S E : 日 期： 2025.08.22 D A T E :____________________________________________________________________ 版 本： A.0 VERSION :____________________________________________________________________ （客户承认受领印）ACCEPTANCE STAMP 拟制跟单员 PREPARED BY 曾小仙 Address:东莞市石碣镇新风西路107号Tel：86-076986016320 Http://www.hartai.com Fax：86-076986372427 MERCHANDISER 工程审核 ENGINEER CHECKED BY 批准 APPROVED BY 邱志辉 ZLGD 东莞市德弗力五金电子材料有限公司 Dongguan city DFL Electronic Technology Co.,LTD ZLGD-Y22.0 39-80-FR ZLGD-0535 Address: No. 107, Xinfeng West Road, Shijie Town, Dongguan City 版本 Rev. A.0 变更前 Before Change -- 变更后内容 DESCRIPTION(Content Or Reason ForChanged) 新发行（Initial Release） 日期 Date 修订者 Revisor 2025/08/22 曾小仙 拟制工程审核 PREPARED BY 曾小仙 ENGINEER CHECKED BY 邱志辉 版 本 变 更 履 历 Version Change History 东莞市德弗力五金电子材料有限公司 Dongguan city DFL Electronic Technology Co.,LTD Address:东莞市石碣镇新风西路107号Tel：86-076986016320 Http://www.hartai.com Fax：86-076986372427 客户料号： CUST P/N 德弗力料号： DFL P/N Page2of 5 ZLGD-Y22.0*39-80-FR ZLGD-0535 1.产品外形尺寸（OVERALL DIMENSIONS OF PRODUCTS): 2.单位(Unit):毫米(mm) A 42.5±0.5 J B 39±1.0 K C D 22.0±0.5 LM E N1/N2 F O G P HI 拟制工程审核 PREPARED BY 曾小仙 ENGINEER CHECKED BY 邱志辉 东莞市德弗力五金电子材料有限公司 Dongguan city DFL Electronic Technology Co.,LTD Address:东莞市石碣镇新风西路107号Tel：86-076986016320 Http://www.hartai.com Fax：86-076986372427 客户料号： CUST P/N 德弗力料号： DFL P/N 规 格 内 容 Specification 20±0.5 Page3of 5 80±3.0 3±2 1±0.2 77±1 A B D E F G H C 0.8±0.2 I 两引 线套 热缩 管 PE 膜 双 面 胶 ZLGD-Y22.0*39-80-FR ZLGD-0535 圈数 Turns 11TS 线径 Wire Dia. 0.08MM*80P热风线 （Silk-Covered Wire） 所有材料要求合格 ROHS 标准 绕线方式 疏/密 Wdg. Type Spred/Close 密绕（Close） 绕线方向 Wdg.Direction （Anticlockwise） 相交 是/否 Intersect Yes/Not 相交（Yes） 线圈 正/反贴 Coil Positive/Anti Paste （Anti/-Paste） 2.电气特性（ELECTRICAL CHARACTERISTICS): 温度 TEMPERATURE:25±10°C,湿度 RELATIVE HUMIDITY:65±10% 序号 NO. 1 2 3 项目 ITEM IND DCR 端子 TERMINAL S-F S-F Q 值 S-F 标准 SPECIFICATION 电感：8.3uH±0.3 阻值： Q 值：8.5 测试条件 TEST FREQUENCY 100kHz/V 100kHz/V 100kHz/V 测试仪器 TEST EQUIPMENTS 拟制工程审核 PREPARED BY 曾小仙 ENGINEER CHECKED BY 邱志辉 规 格 内 容 Specification 东莞市德弗力五金电子材料有限公司 Dongguan city DFL Electronic Technology Co.,LTD Address:东莞市石碣镇新风西路107号Tel：86-076986016320 Http://www.hartai.com Fax：86-076986372427 客户料号： CUST P/N 德弗力料号： DFL P/N SHDA 1062 SHDA 1062 SHDA 1062 Page4of 5 逆时针 反贴 ZLGD-Y22.0*39-80-FR ZLGD-0535 3. 材料清单（BILL OF MATERIAIS): 序号 NO. 材料名称 Material name 1线材 2磁片 3黑膜 4 双面胶 5锡条 6 金手指胶布 7胶水 品名描述 Description 0.08MM 80P热风线 环؊无铅焊锡条 物料代码 Material Code 无铅高温锡条 厂商代码 Vendor code RS ZH / / YX / 拟制工程审核 PREPARED BY 曾小仙 ENGINEER CHECKED BY 邱志辉 东莞市德弗力五金电子材料有限公司 Dongguan city DFL Electronic Technology Co.,LTD Address:东莞市石碣镇新风西路107号Tel：86-076986016320 Http://www.hartai.com Fax：86-076986372427 客户料号： CUST P/N 德弗力料号： DFL P/N 规 格 内 容 Specification / / / / Page5of 5 / / G42.5 0.8MM厚有孔异઻硬磁片+20 1磁片 背胶42无孔带耳朵（开口长13mm，宽11mm） 内孔8MM有耳朵 5MM宽 环؊万能胶+816硅胶 ZLGD-Y22.0 39-80-FR ZLGD-0535 黑膜42异形无孔无耳朵 8热缩管 1 77 MM 热缩管

承 认 书 客户名称(CUSTOMER): 客户料号(PART NO.): 品 名(DESCRIPTION): 规格(SPECIFICATION): 东 莞市德弗力五金电子材料有限公司Dongguan city DFL Electronic Technology Co.,LTD No. 107, Xinfeng West Road, Shijie Town, Dongguan City 电话：0769-86016320 传真：0769-86372427 第 1 页 共 2 页 日 期(DATE): 15x38.5,0.08×105P，磁边起15MM 20230923 SPECIFICATION FOR APPROVEAL 本司确认（TRX APPROVAL） 制作 审核 客户确认（CUSTOMER APPROVAL） 确认结果(Result): 合格不合格 其它 承认日期 工程 批准 承认日期 曾小仙 邱志辉 20230923 Coil + magnetic sheet线圈+磁片 ZLGD-Y15X38.5-15-FR ZLGD-A1-0053 产品型号: SPECIFICATION 二、原理图（schematic diagram:） 拟制/日期PREPARED BY/DATE 审核/日期CHECKED BY/DATE 东莞市德弗力五金电子材料有限公司 Dongguan city DFL Electronic Technology Co.,LTD DESC Rev:A 版本 Customer: Date: Description: 一、尺寸DIMENSION:(mm) A B C D E F G I 注: 三、绕线参数(WindingSpecification:) 序号 NO. 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 Winding Direction 四、电气特性 ELECTRICAL CHARACTERISTICS: 温度 TEMPERATURE:25±10°C,湿度 RELATIVE HUMIDITY:65±20% 序号 NO. 客户/日期CUSTOMEU/DATE 端子 TERMINAL 项目 ITEM 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS 1 2 3 4 IND. IND. Q值 DCR 20230923 15.0±1.0 38.5+1.5 1 0.08×105P丝包线 12TS Counterclockwise 1.线圈贴G44*0.8 硬磁 2.线圈出线位置缠 8MM高温胶带 3.磁片背面贴带耳 朵双面胶 4.线圈不可松线 J K L 44.0±1.0 M N O P 6.8uH±0.3加磁片 100KHz/1.0V SHDA 1062 H Coil + magnetic sheet 15.0±2.0 3.0±2.0 0.8±0.2 C D F ZLGD-Y15X38.5-15-FR ZLGD-A1-0053 B A E

Test Report issued under the responsibility of: Itestek Testing Co., Ltd. (Dongguan) TEST REPORT FEDERAL COMMUNICATIONS COMMISSION FOR WIRELESS POWER TRANSFER Report Number. ........................... : ITA26B07001401W 001 Sample date ................................. : 2026-07-24 Test date ....................................... : 2026-07-24 to 2026-08-27 Issue date ..................................... : 2026-08-27 Total number of pages ................ : 23 Standard/According to ............... : FCC CFR Title 47 Part 15 Subpart C ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a-2024 Template version ......................... : V2.0 Testing Laboratory ...................... : Itestek Testing Co., Ltd. (Dongguan) Address ........................................ : Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Tested by ...................................... : Tom Zhang Checked by .................................. : Oliver Qiao Approved by ................................ : Joker Qi Applicant’s name ......................... : Shenzhen Caibo Technology Co., Ltd. Address ........................................ : F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao'an District, Shenzhen China Manufacturer’s name .................. : Same as applicant Address ........................................ : Same as applicant Factory’s name ............................ : Same as applicant Address ........................................ : Same as applicant Trade Mark ................................... : / Product description .................... : 4-in-1 Magnetic Wireless Charger Model/Type reference ................. : T16, Y-WCS07, WLC05ML, T20, T642-G, T16R Ratings ......................................... : Input: 9Vdc, 3A; 12Vdc, 3A; 15Vdc, 3A; 20Vdc,3A Output: Wireless charging of Phone: 5W, 7.5W, 10W, 15W, 25W Wireless charging of Earphone: 5W Wireless charging of Watch: 2.5W FCC ID .......................................... : 2AXTH-T16 Test result .................................... : Pass Report No.: ITA26B07001401W 001 Page 2 of 23 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Declare: 1. This report shall not be partially reproduced without the consent of the laboratory. 2. If the report without tester's signature, auditor's signature, approver's signature and inspection seal, the report is invalid. 3. The test results are valid only for the tested samples. 4. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above relevant standards. 5. If the report is not stamped with the accreditation recognized seal, it will only be used for scientific research, education, and internal quality control activities, and is not used for the purpose of issuing supporting data to the society. Testing laboratory: Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China FCC designation number CN1436 A2LA has accredited, certificate Number 7609.01 1. Summary of test results Requirement CFR47 Section Result Antenna requirement §15.203 Pass AC Power Line Conducted Emission §15.207 Pass Spurious Emission §15.209 Pass Occupied Bandwidth §15.215(c) Pass Report No.: ITA26B07001401W 001 Page 3 of 23 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 2. General test information 2.1. Description of EUT Details of technical specification refer to the description in follows: Test model number T16 Test sample number A-001 Model different All models are identical, except model number Frequency range (Hz) 110.1K-205K Hz: output power 5W, 7.5W, 10W for phone, output power 5W for earphone, 326.5K Hz: output power 2.5W for watch 360K Hz: output power 15W, 25W for phone Modulation technique ASK Antenna type Coil Antenna Antenna gain 0 dBi Temperature range (°C) -20 ~ 50 Hardware version V1.0 Software version V1.0 Block diagram EUT configuration for test EUT/AE AC Mains Report No.: ITA26B07001401W 001 Page 4 of 23 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 2.2. Test modes Mode Test Status 1 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 2 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 7.5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 3 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 10W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 4 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 15W (360KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 5 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 25W (360KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 6 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) + Wireless …

Text truncated - open the document above for the full version.

Test Report issued under the responsibility of: Itestek Testing Co., Ltd. (Dongguan) TEST REPORT RADIO FREQUENCY FOR WIRELESS POWER TRANSFER Report Number. ........................... : ITA26B07001401W 002 Sample date ................................. : 2026-07-24 Test date ....................................... : 2026-07-24 to 2026-08-27 Issue date ..................................... : 2026-08-27 Total number of pages ................ : 8 Standard/According to ............... : KDB 680106 D01 Wireless Power Transfer v04 Template version ......................... : V2.0 Testing Laboratory ...................... : Itestek Testing Co., Ltd. (Dongguan) Address ........................................ : Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Tested by ...................................... : Tom Zhang Checked by .................................. : Oliver Qiao Approved by ................................ : Joker Qi Applicant’s name ......................... : Shenzhen Caibo Technology Co., Ltd. Address ........................................ : F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao'an District, Shenzhen China Manufacturer’s name .................. : Same as applicant Address ........................................ : Same as applicant Factory’s name ............................ : Same as applicant Address ........................................ : Same as applicant Trade Mark ................................... : / Product description .................... : 4-in-1 Magnetic Wireless Charger Model/Type reference ................. : T16, Y-WCS07, WLC05ML, T20, T642-G, T16R Ratings ......................................... : Input: 9Vdc, 3A; 12Vdc, 3A; 15Vdc, 3A; 20Vdc,3A Output: Wireless charging of Phone: 5W, 7.5W, 10W, 15W, 25W Wireless charging of Earphone: 5W Wireless charging of Watch: 2.5W FCC ID .......................................... : 2AXTH-T16 Test result .................................... : Pass Report No.: ITA26B07001401W 002 Page 2 of 8 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Declare: 1. This report shall not be partially reproduced without the consent of the laboratory. 2. If the report without tester's signature, auditor's signature, approver's signature and inspection seal, the report is invalid. 3. The test results are valid only for the tested samples. 4. After test and evaluation, our opinion is that the equipment provided for test compliance with the requirement of the above relevant standards. 5. If the report is not stamped with the accreditation recognized seal, it will only be used for scientific research, education, and internal quality control activities, and is not used for the purpose of issuing supporting data to the society. Testing laboratory: Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China FCC designation number CN1436 A2LA has accredited, certificate Number 7609.01 Report No.: ITA26B07001401W 002 Page 3 of 8 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 1. General test information 1.1. Description of EUT Details of technical specification refer to the description in follows: Test model number T16 Test sample number A-001 Model different All models are identical, except model number Frequency range (Hz) 110.1K-205K Hz: output power 5W, 7.5W, 10W for phone, output power 5W for earphone 326.5K Hz: output power 2.5W for watch 360K Hz: output power 15W, 25W for phone Modulation technique ASK Antenna type Coil Antenna Antenna gain 0 dBi Temperature range (°C) -20 ~ 50 Hardware version V1.0 Software version V1.0 Block diagram EUT configuration for test EUT/AE AC Mains Report No.: ITA26B07001401W 002 Page 4 of 8 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China 1.2. Test modes Mode Test Status 1 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 2 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 7.5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 3 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 10W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 4 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 15W (360KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 5 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 25W (360KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) + Wireless charging of watch for output 2.5W (326.5KHz) 6 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) 7 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 7.5W (110.1K-205KHz) + Wireless charging of earphone for output 5W (110.1K-205KHz) 8 AC Mains (120Vac, 60Hz) + Wireless charging of phone for output 10W (110.1K-205KHz) + W…

Text truncated - open the document above for the full version.

Report No. ITA26B07001401WPage 1 o f 4 I testek Testing Co., Ltd . (Dongguan) Room 116, Build ing 8 and Room 606, Building 3, Innovation Port of H anyuwan, Li yu an R oad, Tangwei, Fuhai Subdist rict, Bao'an Distri ct, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Int ernal view Details of:Int ernal view Report No. ITA26B07001401WPage 2 o f 4 I testek Testing Co., Ltd . (Dongguan) Room 116, Build ing 8 and Room 606, Building 3, Innovation Port of H anyuwan, Li yu an R oad, Tangwei, Fuhai Subdist rict, Bao'an Distri ct, Shenzhen, Guangdong, 518000, People's Republic of China Details of:Int ernal view Details of:PCB view Report No. ITA26B07001401WPage 3 o f 4 I testek Testing Co., Ltd . (Dongguan) Room 116, Build ing 8 and Room 606, Building 3, Innovation Port of H anyuwan, Li yu an R oad, Tangwei, Fuhai Subdist rict, Bao'an Distri ct, Shenzhen, Guangdong, 518000, People's Republic of China Details of:PCB view Details of:WPT antenna for watch view Report No. ITA26B07001401WPage 4 o f 4 I testek Testing Co., Ltd . (Dongguan) Room 116, Build ing 8 and Room 606, Building 3, Innovation Port of H anyuwan, Li yu an R oad, Tangwei, Fuhai Subdist rict, Bao'an Distri ct, Shenzhen, Guangdong, 518000, People's Republic of China Details of:WPT antenna for earphone view Details of:WPT antenna for phone view

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Telephone No: 708-571-3148 Email: [email protected] Applicant: Company name: Shenzhen Caibo Technology Co., Ltd. Product Description: 4-in-1 Magnetic Wireless Charger Grantee code: 2AXTH FCC ID:2AXTH-T16 FRN： 0030078273 Contact Name: Linjun Hu Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an District, Shenzhen, China Telephone No: 13713719057 Email: [email protected] [Shenzhen Caibo Technology Co., Ltd.] certifies that, as of the date of this filing of the application with the TCB, [FCC US Agent, LLC] is our designated US agent for service of process for the above referenced FCC ID. [Shenzhen Caibo Technology Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2026/08/31 Applicant’s Name: Linjun Hu US Agent’s Name: Tim Payne Title: CEO Title: President Signature Signature

Report No. ITA26B07001401W Pa ge 1 o f 4 I testek Testing Co., Ltd . (Dongguan) Room 116, Build ing 8 and Room 606, Building 3, Innovation Port of H anyuwan, Li yu an R oad, Tangwei, Fuhai Subdist rict, Bao'an Distri ct, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001401W Page 2 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001401W Page 3 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view Details of:External view Report No. ITA26B07001401W Page 4 of 4 Itestek Testing Co., Ltd. (Dongguan) Room 116, Building 8 and Room 606, Building 3, Innovation Port of Hanyuwan, Liyuan Road, Tangwei, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518000, People's Republic of China Details of:External view

Shenzhen Caibo Technology Co., Ltd. C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Caibo Technology Co., Ltd. Address: F4, Building 30, Fifth Industrial Zone, Huaide Cuigang Industrial Park, Fu Yong, Bao’an Dis…

Text truncated - open the document above for the full version.