AS5CMP-39Power Amplifier

1 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Front and Left Side of Primary Frame, showing DC supply voltage input Nominal Dimensions: 67 “ (170 cm) H x 28” (71 cm) W x 24 “ (61 cm) D 2 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Front and Right Side of Primary Frame Nominal Dimensions: 67 “ (170 cm) H x 28” (71 cm) W x 24 “ (61 cm) D 3 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Front and Right Side of Primary Frame, with door open to show interior configuration. Nominal Dimensions: 67 “ (170 cm) H x 28” (71 cm) W x 24 “ (61 cm) D 4 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Front Close-up of Lower Half of Primary Frame Showing TTU Amplifier, 2:1 Combiner and Band Pass Transmit Filter Shelf 5 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Front Close-up of PCS TDMA Transmit Units (TTU); FCC ID: AS5CMP-39 6 TTUs/Primary Frame 6 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Rear of Primary Frame, showing transmit and receive antenna terminals plus alarm and T1 cabels. 7 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 4: EXTERNAL PHOTOGRAPHS AUTOPLEX ™ System 1000, Series II, PCS TDMA Minicell, J41683A-1, Base Station Equipment View: Rear of Primary Frame with door removed to show interior configuration.

1 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 2: FCC ID LABEL SAMPLE AND LOCATION INFORMATION The FCC ID label that will be displayed on the PCS TDMA Transmit Unit (TTU) power amplifier shall be in accordance with the following drawing and displayed on the TTU as shown: TTU Label Placement FCC ID: AS5CMP-39

2 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Front and Left Side View: Device Side 3 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Front Faceplate 4 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Front and Right Side View: Heat Sink Side 5 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Heat Sink Close-Up View 6 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Device Side Cover Close-Up View 7 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Device Cover Removed Showing Interior Surfaces 8 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Device Side of Circuit Board Close-Up View

2 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Top View: PWB Device Surface Prior to Assembly 3 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Bottom View: PWB Bottom Surface Prior to Assembly

APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 13: PARTS LIST The Lucent Technologies AUTOPLEX™ System 1000, Series II, PCS TDMA Transmit Unit (TTU), subject of this application under FCC ID: AS5CMP-39, is a base station frequency up-converting, from cellular to PCS, power amplifier. There is no document that provides a separate listing of parts and components. The schematic diagrams in Exhibit 9 were supplied by Lucent’s contracted manufacturer and show the parts used on the circuit packs, which are considered as CONFIDENTIAL.

APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 12: TUNING PROCEDURE The Lucent Technologies AUTOPLEX™ System 1000, Series II PCS TDMA Transmit Unit (TTU), subject of this application under FCC ID: AS5CMP-39, is a base station frequency up-converting, from cellular to PCS, power amplifier. As such, it does not have and does not require any tuning procedure outside of the standard manufacturing test, evaluation and adjustment processes.

1 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 EXHIBIT 10: TEST REPORT The test report attached to this exhibit demonstrates that the Lucent Technologies, AUTOPLEX™ System 1000, Series II, PCS TDMA Transmit Unit (TTU), subject of this application for certification under FCC ID: AS5CMP-39, is in full compliance with all requirements of the Rules of the Commission as specified in the Code of Federal Regulations (CFR), Title 47 – Telecommunication; Part 24, Subpart E – Broadband PCS; Section 24.238 - Emission Limits; effective October 1, 2000. All testing was performed in accordance with CFR 47, Part 2, Subpart J – Equipment Authorization Procedures; Revised January 31, 2001. All testing was performed in the Lucent Technologies, Whippany, NJ, compliance laboratory by F. E. Chetwynd and M. P. Farina during the period February 20 to May 16, 2001. This test program was implemented in adherence to a test plan generated by M. P. Farina, in accordance with Lucent’s ISO-9001 Registration. All measurement instrumentation utilized were calibrated also in compliance with Lucent’s ISO-9001 Registration. The Whippany 3 & 10 Meter Open Area Test Site (OATS) is authorized by the Federal Communications Commission (FCC) under Registration Number: 90770, in compliance with the the requirements of Section 2.948 of the Rules of the Commission. Frequency stability measurements were performed by T. N. Tye, Lucent Technologies, Columbus, Ohio under the direction of M. P. Farina, and in adherence to the previously cited ISO 9001 test plan. This test program was conducted during the interval April 19 to May 17, 2001. 2 67 Whippany Road Whippany, NJ 07981 Subject: Application for Certification of the LucentMichael P. Farina Technologies PCS TDMA Transmit UnitJW10E0000 (TTU) Base Station Power Amplifier,Telephone: 973-386-4344 under FCC ID: AS5CMP-39.Facsimile: 973-386-3116 [email protected] May 25, 2001 TEST REPORT SYNOPSIS: The Lucent Technologies, AUTOPLEX™ System 1000, Series II, PCS TDMA Transmit Unit (TTU), subject of this application for certification under FCC ID: AS5CMP-39, is designed as a frequency up- converting, from cellular to PCS, base station power amplifier. The TTU is specifically designed as a single carrier amplifier specific to 30 kHz bandwidth, Time Domain Multiple Access (TDMA) technology carriers. The maximum rated average power output at the TTU RF output terminal 60 Watts (47.8 dBm), per single carrier. The TTU is also designed for utilization in Lucent’s AUTOPLEX ™ System 1000, Series II, PCS-TDMA Minicell J41683A-1. Path losses in the Minicell due to 2:1 combiner, dual band PCS transmit bandpass filter and coaxial cabling attenuate the 60 Watt TTU output power to nominally 16 Watts (42.0 dBm) average at the Minicell transmit antenna terminal (J4) per single carrier. All conducted emissions tests were performed at the J4 transmit antenna terminal with the single carrier power level adjusted to provide the antenna terminal rated power level of 16 Watts (42.0 dBm) average. The TDMA signal source, utilized for all tests in this report, is Lucent’s Enhanced Digital Radio Unit (EDRU) transceiver, which was previously authorized under FCC ID: AS5CMP-17. The EDRU transmits a single carrier, in the cellular frequency band (869-894 MHz), modulated in all three time slots using ¼- DQPSK TDMA modulation. The emission designator characteristic of this TDMA carrier is 40K0GXW. Using appropriate frequency mixing and filtering, the TTU up-converts the cellular frequency carrier input signal, nominally at +10 dBm, to the PCS frequency band (1930-1990 MHz) and then performs power amplification to provide the rated 60 Watts (47.8 dBm) average maximum at the TTU RF output terminal (J5). The 60 Watt PCS carrier is then transmitted through a 2:1 signal combiner, band pass transmit filter and coaxial cabling to provide a corresponding and attenuated power level at the J4 transmit antenna terminal of nominally 16 Watts (42.0 dBm) average, which is the rated transmit power level for the Minicell. The TTU is designed to provide a nominal gain of 37 dB across the PCS frequency band, at a nominal supply source of 27.25 Vdc. All testing was performed in the Lucent Technologies, Whippany, NJ, compliance laboratory by F. E. Chetwynd and M. P. Farina during the period February 20 to May 164rt, 2001. This test program was implemented in adherence to a test plan generated by M. P. Farina, in accordance with Lucent’s ISO-9001 Registration. All measurement instrumentation utilized were calibrated also in compliance with Lucent’s ISO-9001 Registration. The Whippany 3 & 10 Meter Open Area Test Site (OATS) is authorized by the Federal Communications Commission (FCC) under Registration Number: 90770, in compliance with the the requirements of Section 2.948 of the Rules of the Commission. 3 APPLICANT: LUCENT TECHNOLOGIESFCC ID: AS5CMP-39 Frequency stability measurements were performed by T. N. Tye, Lucent Technologies, Columbus, Ohio under the direction of M. P. Farina, and in adherence to the previously cited ISO 9001 test plan. This test program was conducted during the interval April 19 to May 17, 2001. This report fully documents all required tests and the test results, sufficient to show full compliance with the Rules of the Commission. APPLICABLE FCC RULES AND INDUSTRY STANDARDS: The AUTOPLEX™ System 1000, Series II PCS TDMA Transmit Unit (TTU), subject of this application for certification under FCC ID: AS5CMP-39, and the PCS-TDMA Minicell J41683A-1 were designed in accordance with the guidelines of TIA/EIA/IS-138-A, TDMA Cellular/PCS – Radio Interface – Minimum Performance Standards for Base Stations, July 1996. The TTU demonstrated full compliance with CFR 47, Part 24, Subpart E – Broadband PCS, and Part 24.238 Emission Limits, effective October 1, 2000; following the test procedures and requirements specified in CFR 47, Part 2, Subpart J – Equipment Authorization Procedures; Revised January 31, 2001. The specifi…

Text truncated - open the document above for the full version.