AS5ONEBTS-08Multi Carrier Radio 850 (MCR850)

Correspondence Summary Q & A November 16, 2004 SUBJECT: LUCENT TECHNOLOGIES INC.(HOLMDEL) - FCC ID: AS5ONEBTS-08 1. TCB Question: Radiated spurious emissions – part 2.1053/ SUBEXHIBIT 11.6: The FCC requires (since 1999) that the measurements for licensed devices be performed using the method of measurement as prescribed in ANSI/TIA/EIA- 102.CAAA or ANSI/TIA/EIA-603 (not ANSI C63.4 which is only for part 15 devices). The calculation method using the free space equation to derive the power into a ½ wave dipole from a field strength measurement is no longer accepted by the FCC. Please revise the test data and method of measurement accordingly. Applicant’s Answer: Radiated Spurious emissions test method submitted in AS5ONEBTS-08 have been used and submitted by Lucent and other manufactures for Part 22 and 24 applications many times since 1999 (see AS5CMP-46; AS5ONEBTS-06, IHET5DJ1, ...). CFR 47 Sect. 2.947 Measurement Procedure (3) states "Any measurement procedure acceptable to the commission may be used to prepare data demonstrating compliance with the requirements of this chapter." CFR 47 Sect. 1053 (a) states "...Information submitted shall include the relative radiated power of each spurious emission with reference to the rated power output of the transmitter, assuming all emission are radiated from halfwave dipole antennas." From FCC Interpretations Database Site, questions regarding 2.1053 INQUIRY: To date we have perform and submitted Harmonic emission compliance using a converted -13 dBm to a field strength limit @ 3 meters (82.2 dBuV/m for EIRP or 84.2 dBuV/m for ERP). Again, is this still the acceptable method or is the substitution now the only preferred test method? RESPONSE: FOR CONSISTENCY, WE WANT EVERYONE TO USE THE SUBSTITUTION METHOD. HOWEVER, WHEN THE INITIAL MEASURED FIELD STRENGTH LEVELS OF THE SPURIOUS EMISSIONS ARE MORE THAN 20 DB BELOW THE ABOVE CITED LEVELS, THEN CONTINUATION WITH THE SUBSTITUTION METHOD IS NOT NECESSARY. The information provided in AS5ONEBTS-08 Subexhibit 11.6 meets the above requirements (emissions more than 20 dB below cited levels). TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 [email protected]

APPLICANT: Lucent Technologies EXHIBIT 8 FCC ID: AS5ONEBTS-08 EXHIBIT 8 Section 2.1033 (c)(12) PHOTOGRAPHS OF THE EQUIPMENT Photographs (8 x 10) of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. Insofar as these requirements are met by photographs or drawings contained in instruction manuals supplied with the certification request, additional photographs are necessary only to complete the required showing. Response The following pages contain the required photographs of the AS5ONEBTS-08 MCR850 transceiver, subject of this application, showing the board layout and component placement. The attached photos include: 1) Front View of MCR850, 2) Rear View of MCR850, 3) Circuit Board Component Side View of MCR850, 4) Circuit Board Wiring Side View of MCR850, 5) Front View of Lucent Technologies Flexent® OneBTS® shelf with MCR850. Page 1 of 6 APPLICANT: Lucent Technologies EXHIBIT 8 FCC ID: AS5ONEBTS-08 Page 2 of 6 23.2 cm AS5ONEBTS-08 MCR850 Transceiver Front View 2.0 cm APPLICANT: Lucent Technologies EXHIBIT 8 FCC ID: AS5ONEBTS-08 AS5ONEBTS-08 MCR850 Transceiver Rear View Page 3 of 6 APPLICANT: Lucent Technologies EXHIBIT 8 FCC ID: AS5ONEBTS-08 Page 4 of 6 Front: Faceplate Rear 37.4 cm AS5ONEBTS-08 MCR850 Transceiver Circuit Board Component Side iew V APPLICANT: Lucent Technologies EXHIBIT 8 FCC ID: AS5ONEBTS-08 Page 5 of 6 AS5ONEBTS-08 MCR850 Transceiver Circuit Board Wiring Side View Rear Front APPLICANT: Lucent Technologies EXHIBIT 8 FCC ID: AS5ONEBTS-08 Page 6 of 6 Front View of Lucent Technologies Flexent® OneBTS® shelf AS5ONEBTS-08 MCR850

APPLICANT: Lucent Technologies EXHIBIT 7 FCC ID: AS5ONEBTS-08 EXHIBIT 7 Section 2.1033 (c)(11) EQUIPMENT IDENTIFICATION LABEL A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. Response The engineering drawing of the label for the AS5ONEBTS-08 MCR850 is attached to this exhibit. The photo showing the label placement is given in this exhibit as well. Page 1 of 3 APPLICANT: Lucent Technologies EXHIBIT 7 FCC ID: AS5ONEBTS-08 Page 2 of 3 APPLICANT: Lucent Technologies EXHIBIT 7 FCC ID: AS5ONEBTS-08 Photograph of Label Placement The left side view of the AS5ONEBTS-08 MCR850 transceiver is attached here. Front AS5ONEBTS-08 Label Placement Rear Page 3 of 3

APPLICANT: Lucent Technologies EXHIBIT 11 FCC ID: AS5ONEBTS-08 EXHIBIT 11 TEST REPORT This test report presents the measurement data required by the Commission for certifying the AS5ONEBTS-08 MCR850 cellular transceiver, subject of this application. All the testing was performed during the period of September 7 – November 5, 2004. The measurement results have demonstrated the AS5ONEBTS-08 MCR850 transceiver is in full compliance with the Rules of the Commission. For some of the required measurements where FCC Parts 2 and 22 did not give specific requirements, TIA/EIA-97-D’s requirements were used in the report, which are almost identical to the 3GPP2 C.S0010-A v1.0’s requirements. Page 1 of 42 APPLICANT: Lucent Technologies EXHIBIT 11 FCC ID: AS5ONEBTS-08 SUBEXHIBIT 11.1 Section 2.1033 (c)(14) REQUIRED MEASUREMENT DATA The required measurement data is presented in the following exhibits as follows: SUBEXHIBIT 11.2 Section 2.1046 Measurements Required: RF Power Output SUBEXHIBIT 11.3 Section 2.1047 Measurements Required: Modulation Characteristics SUBEXHIBIT 11.4 Section 2.1049 Measurements Required: Occupied Bandwidth SUBEXHIBIT 11.5 Section 2.1051 Measurements Required: Spurious Emissions at Antenna Terminals SUBEXHIBIT 11.6 Section 2.1053 Measurements Required: Field Strength of Spurious Radiation SUBEXHIBIT 11.7 Section 2.1055 Measurements Required: Frequency Stability SUBEXHIBIT 11.8 Section 2.947 Listing of Test Equipment Used Page 2 of 42 APPLICANT: Lucent Technologies EXHIBIT 11 FCC ID: AS5ONEBTS-08 SUBEXHIBIT 11.2 Section 2.1046 MEASUREMENT REQUIRED: RF POWER OUTPUT This test is a measurement of the RF power level transmitted at the AS5ONEBTS-08 MCR850 output terminal combiner, as shown in the accompanying test set-up diagram. All the carriers were configured with a combination of Pilot, Sync, Paging and Traffic channels. The Pilot/Sync/Page channels were set up according to the recommended test model for base stations given in TIA/EIA-97-D (Section 6), as shown in the following table. The AS5ONEBTS-08 MCR850 does not have transmit diversity. Table 11.2.1. Base Station Test Model, Nominal Type Number of Channels Fraction of Power (linear) Fraction of Power (dB) Comments Pilot 1 0.2000 -7.0 Walsh 0 Sync 1 0.0471 -13.3 Walsh 32, always 1/8 rate Paging 1 0.1882 -7.3 Walsh 1, full rate only Traffic 6 0.09412 each -10.3 each Variable Walsh assignments, full rate only Power measurements were made with a Giga-tronics 8542C Universal Power Meter with 80621A Power Sensor (0.01 – 18 GHz) in the average mode. The test set-up for conducting the RF power output measurement from the MCR850 is shown in the following figure. Before the testing was started, the Base Station was given a sufficient “warm-up” period as required. The measured channels and results are tabulated in the following table: Table 11.2.2.1 Results of RF Power Output – Single Carrier Cellular Channel No. Frequency (MHz) Cellular Frequency Band MCR850 Output (dBm) 1019 869.88 A” 4.92 37 871.11 A3 4.90 78 872.34 4.87 119 873.57 4.86 160 874.80 A2 4.89 201 876.03 4.91 242 877.26 A1 4.89 283 878.49 4.90 384 881.52 4.95 425 882.75 B1 4.94 466 883.98 4.90 507 885.21 4.89 548 886.44 B2 4.91 589 887.67 4.92 630 888.90 B3 4.89 691 890.73 A’ 4.90 777 893.31 B’ 4.95 Page 3 of 42 APPLICANT: Lucent Technologies EXHIBIT 11 FCC ID: AS5ONEBTS-08 Table 11.2.2.2 RF Power Output – Multi-Carrier Left Edge / Right Edge 2 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37 A”/A3 8.05 6.4 589, 630 B3/B2 8.05 6.47 3 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37, 78 A”/A3/A2 9.55 9.1 548, 589, 630 B3/B2 9.87 9.8 4 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37, 78, 119 A”/A3/A2 11.14 13 507, 548, 589, 630 B3/B2 11.14 13 5 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37, 78, 119, 160 A”/A3/A2 12.01 16 466, 507, 548, 589, 630 B3/B2/B1 12.02 16 6 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37, 78, 119, 160, 201 A”/A3/A2/A1 12.9 19.2 425, 466, 507, 548, 589, 630 B3/B2/A1 12.81 19 7 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37, 78, 119, 160, 201, 242 A”/A3/A2/A1 13.42 22.1 384, 425, 466, 507, 548, 589, 630 B3/B2/B1 13.4 22 8 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Milli-Watts) 1019, 37, 78, 119, 160, 201, 242, 283 A”/A3/A2/A1 13.97 25 Results: The above RF power measurements meet TIA/EIA-97-D, Section 4.3.1.3, which specifies that the total power per carrier should remain within +2dB and -4dB of the manufacturer’s rated power. The RF power outputs of the MCR850 across the Cellular Frequency Band 869.0 – 894 MHz are in full compliance with the Rules of the Commission. Page 4 of 42 APPLICANT: Lucent Technologies EXHIBIT 11 FCC ID: AS5ONEBTS-08 FIGURE 11.2.1 TEST SET-UP FOR MEASUREMENT OF RADIO FREQUENCY POWER OUTPUT Tx1 Tx2 C 1-4 C 5-8 15 MHz MCR850 AS5ONEBTS-08 Giga-tronic 8452C Power Meter With 80621A Power Senso r 2:1 Combiner Common Timing Unit & Oscillator Module Page 5 of 42 APPLICANT: Lucent Technologies EXHIBIT 11 FCC ID: AS5ONEBTS-08 SUBEXHIBIT 11.3 Section 2.1047 MEASUREMENT REQUIRED: MODULATION CHARACTERISTICS The MCR850 utilizes digital QPSK modulation. The modulation accuracy measures the ability of the transmitter to generate the ideal signal which is defined by the waveform quality. The waveform quality is measured by determining the normalized correlated power between the actual waveform and the ideal waveform. TIA/EIA-97D, Section 4.2.2.3, requires the normalized cross correlation coefficient ρ shall be greater than 0.912. The modulation accuracy measurements were performed with a carrier configured with the forward pilot channel only. The measurements were made at the output terminal of the MCR850 AS5ONEBTS-08. The measurements were performed with an Agilent E4440A PSA…

Text truncated - open the document above for the full version.