AS5ONEBTS-11UMTS-CDMA TRANSCEIVER SYSTEM (850)

1 APPLICANT: Lucent Technologies, Inc. FCC ID: AS5ONEBTS-11 67 Whippany Road Subject: Application for Certification under FCC ID: Whippany, NJ 07981 AS5ONEBTS-11, Covering the UMTS/W-CDMA Transceiver System Operating in the Cellular Rudolf J. Pillmeier Radiotelephone Service, 869-894 MHz, Spectrum. Telephone: 973-386-3837 E-Mail: [email protected] June 22, 2005 Mr. Sid Sanders, President Timco Engineering, Inc. 849 N. W. State Road 45, P. O. Box 370 Newberry, Florida 32669 Dear Mr. Sanders: Lucent Technologies’ UMTS-CDMA Transceiver System (850) is designed to operate in the Lucent UMTS 850 Flexent® OneBTS™ Wireless Base Station, configured for 3S1C operation over the Cellular Frequency Spectrum 869-894 MHz. The objective of this application is to obtain FCC authorization as a new filing, under FCC ID: AS5ONEBTS-11, for operation in the Universal Mobile Telecommunications System (UMTS) with a single 5 MHz emission bandwidth carrier (4M10F9W), set to a maximum power level at the antenna terminal of 40 Watts (3-second) per carrier. The UMTS850 Transceiver System consists of the principle RF components: (1) Crystal Reference Oscillator Module (OMA) 15 MHz, (2) UMTS-CDMA Multi-Carrier CDMA Radio MCR850, Model BNJ65, (3) C2PAM power amplifier, and (4) 25 MHz Dual Duplex (DDpx), low loss, transmit filter covering the Cellular Spectrum 869-894 MHz. These components are considered as a system due to (1) the DDpx filters providing RF feedback to the transceiver in the form of Closed Loop Gain Control (CLGC) to provide constant power over temperature, and (2) Lucent’s proprietary Enhanced Digital Pre-Distortion (EDPD-UL) technology which enables software to communicate between the transceiver, power amplifier and the transmit filter to achieve this goal. The MCR850 transceiver can transmit either Voice with 20 active channels or Voice + HSDPA ( High Speed Downlink Packet Access) with 24 active channels. The UMTS feature was developed for the North America Region (NAR) deployment, and is also known as Wideband CDMA (W-CDMA). The transceiver can be converted from Multi-Carrier CDMA to Single Carrier UMTS (or UMTS to CDMA) by software alone, which can be performed at the installation site. There are no physical, hardware or circuit changes to the transceiver. UMTS functionality for the MCR850 transceiver was developed in accordance to the guidelines of the ETSI TS 25.141 V5.9.0 (2004-09) standard: “Universal Mobile Telecommunications System (UMTS); Base Station Conformance Testing (FDD) (3GPP TS 25.141 version 5.9.0 Release 5)”. The measurement exhibits attached to this application demonstrate full compliance with both FCC Part 22 Subpart H – Cellular Radiotelephone Service and with ETSI TS 25.141, following the procedural requirements specified in FCC Part 2 Subpart J – Equipment Authorization Procedures. The data summarized below is in the form presently used by the Commission’s Radio Equipment List, Equipment Acceptable for Licensing. Manufacturer Lucent Technologies Equipment Identification AS5ONEBTS-11 Rules Part Number Part 22, Subpart H – Cellular Radiotelephone Service Frequency Ranges Transmit 869–894 MHz Output Power 40 Watts (+46 dBm) 3-second average at the Tx antenna terminal Frequency Tolerance ± 0.05 ppm Emission Designator 4M10F9W 2 APPLICANT: Lucent Technologies, Inc. FCC ID: AS5ONEBTS-11 Attached are the FCC Form 731 (Application for Equipment Authorization – Radio Frequency Devices) and the required measurement data and exhibits specific to this request for initial equipment authorization of the UMTS-CDMA Transceiver System (850) base station. The technical contact at Lucent Technologies will comply with any request for additional information should the need arise. The attached exhibits are assembled and presented in the sequence recommended by Timco Engineering, in accordance with the Table of Contents attachment. Confidentiality is requested for the following exhibits: Exhibit 5: Internal Photographs Exhibit 7: Operational Description (Theory of Operation, Functional Description) Exhibit 8: Block Diagrams Exhibit 9: Schematic Diagrams Exhibit 11: UMTS FLEXENT® UMTS Macrocell Indoor – Operation, Administration and Maintenance Document Exhibit 13: Parts List, if Applicable Sincerely, Rudolf J. Pillmeier Technical Manager FCC/EMC Compliance Test Group Whippany, NJ Att. Table of Contents for the UMTS-CDMA Transceiver System (850) Certification Report 3 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 TABLE OF CONTENTS Cover Letter Request for Confidentiality Exhibit 1: 731 Form Exhibit 2: FCC ID Label Sample and Location Information Exhibit 3: FCC Required Information (Part 2.1033) Exhibit 4: External Photographs Exhibit 5: Internal Photographs - LUCENT TECHNOLOGIES CONFIDENTIAL Exhibit 6: Test Set Up Photographs Exhibit 7: Operational Description (Theory of Operation, Functional Description) - LUCENT TECHNOLOGIES CONFIDENTIAL Exhibit 8: Block Diagrams - LUCENT TECHNOLOGIES CONFIDENTIAL Exhibit 9: Schematic Diagrams - LUCENT TECHNOLOGIES CONFIDENTIAL Exhibit 10: Test Report Exhibit 11: UMTS FLEXENT® UMTS Macrocell Indoor – Operation, Administration and Maintenance Document –LUCENT TECHNOLOGIES CONFIDENTIAL Exhibit 12: Tuning Procedure, if Applicable Exhibit 13: Parts List, if Applicable LUCENT TECHNOLOGIES CONFIDENTIAL

1 APPLICANT: Lucent Technologies, Inc. FCC ID: AS5ONEBTS-11 67 Whippany Road Subject: REQUEST FOR CONFIDENTIALITY Whippany, NJ 07981 for FCC ID: AS5ONEBTS-11, Covering the Cellular Frequency UMTS – CDMA Transceiver Rudolf J. Pillmeier System (850). Telephone: 973-386-3837 Facsimile: 973-386-3116 E-Mail: [email protected] Timco Engineering, Inc. June 22, 2005 849 N. W. State Road 45 P. O. Box 370 Newberry, Florida 32669 Dear Sid Sanders: On behalf of Lucent Technologies, I hereby request that the following exhibits, included in this Application for Certification, under FCC ID: AS5ONEBTS-11, covering the Lucent UMTS Flexent® OneBTS™ UMTS 850 wireless base station transceiver system be maintained as confidential information and not be made available for public inspection at any time. Exhibit 5: Internal Photographs Exhibit 7: Operational Description (Theory of Operation, Functional Description) Exhibit 8: Block Diagrams Exhibit 9: Schematic Diagrams Exhibit 11: UMTS Flexent® OneBTS™ Macrocell +24V Indoor Operation, Administration and Maintenance Exhibit 13: Parts List, if Applicable These exhibits contain Lucent Technologies proprietary information that is considered to be trade secrets, with possible patents pending, and the property of Lucent Technologies, pursuant to the provisions of Part 0.457(d) of the Commission’s Rules. These exhibits also contain design information that is highly proprietary to Lucent’s contracted manufacturer/supplier. Exhibits 5,7, 8, 9, and 13 are highly proprietary and contain critical design information that can not be made available for public inspection. This information is proprietary both to Lucent Technologies and to Lucent’s contracted manufacturer/supplier. The UMTS Flexent® OneBTS™ Macrocell +24V Indoor Operation, Administration and Maintenance document, included in Exhibit 11, is not furnished to the user, except under very exceptional and very limited circumstances. This manual contains highly proprietary circuit, equipment and architecture descriptions that must not be made available for public inspection. The cover/title page is explicitly labeled “Unpublished and Not for Publication”. Thank you for your consideration in this matter. Sincerely, Rudolf J. Pillmeier Technical Manager FCC/EMC Compliance Test Group Whippany, NJ

Page 1 of 6 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 4: EXTERNAL PHOTOGRAPHS Lucent UMTS Flexent® OneBTS™ 850 MHz Wireless Base Station, incorporating the UMTS-CDMA Multi-Carrier CDMA Radio (MCR850), BNJ65; the C2PAM power amplifier, and the 25 MHz wideband, low loss, Dual Duplex (DDpx) bandpass filters configured for 3S1C operation at 40 Watts/Carrier is shown in the following photographs. View: UMTS850 Macrocell Equipment Frame Front and Left Side View. Page 2 of 6 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 4: EXTERNAL PHOTOGRAPHS View: UMTS850 Macrocell Equipment Frame Rear and Right Side View. Page 3 of 6 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 4: EXTERNAL PHOTOGRAPHS View: UMTS850 Macrocell Equipment Frame Front View with Door Open Page 4 of 6 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 4: EXTERNAL PHOTOGRAPHS View: UMTS850 Macrocell Equipment Frame Front View Closeup, Showing the Digital Shelves with Multi-Carrier CDMA Radio (MCR850), BNJ65, and the Crystal Oscillator Module (OMA). Page 5 of 6 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 4: EXTERNAL PHOTOGRAPHS View: UMTS850 Macrocell Equipment Frame Front View Closeup, Showing the Power Amplifier Shelf . Page 6 of 6 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 4: EXTERNAL PHOTOGRAPHS View: UMTS850 Macrocell Equipment Frame Front View Closeup, Showing the 25 MHz Dual Duplex Filter Shelf .

1 1 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 2: FCC ID LABEL SAMPLE AND LOCATION INFORMATION SECTION 2.1033(c) (11) also SECTION 2.925 (a) (1) A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. The FCC ID label representing the UMTS Flexent® OneBTS™ wireless base station, UMTS-CDMA Transceiver System (850) will be displayed on the Multi-Carrier CDMA Radio MCR850, BNJ65, and shall be in accordance with the following drawing as shown: PCS Multi-Carrier CDMA Radio (MCR850), BNJ65 Lucent Technologies UMTS-CDMA Transceiver System (850) FCC ID: AS5ONEBTS-11

1 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 12: TUNING PROCEDURE Section 2.1033 (c)(9): Tune-up procedure over the power range, or at specific operating power levels. Response: The Lucent UMTS850 Flexent® OneBTS™ 850 MHz Wireless Base Station incorporates the UMTS- CDMA Multi-Carrier CDMA Radio (MCR850), BNJ65; the C2PAM power amplifier; and the 25 MHz wideband, low loss, Dual Duplex (DDpx) bandpass filter, which comprise the UMTS850 UMTS-CDMA Transceiver System (850), that is the subject of this application for certification, does not have and does not require any tuning procedure outside of the standard manufacturing test, evaluation and adjustment processes. There is no user tune-up procedure

Lucent Technologies Inc. - Proprietary Use pursuant to Company Instructions. Page 1 of 51 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 10: TEST REPORT SYNOPSIS The test report attached to this exhibit demonstrates that the Lucent Technologies’ Cellular Frequency UMTS-CDMA Transceiver System (850), which is designed to operate in the Lucent UMTS Flexent® OneBTS™ 850 MHz Wireless Base Station, is in full compliance with all requirements of the Rules of the Commission as specified in the Code of Federal Regulations (CFR), Title 47 – Telecommunication; Part 22, Subpart H – Cellular Radiotelephone Service; Section 22.917 - Emission Limitations for Cellular Equipment; effective October 1, 2004. All testing was performed in accordance with CFR 47, Part 2, Subpart J – Equipment Authorization Procedures; effective October 1, 2004. It also demonstrates compliance with the spurious emissions limitations specified in ETSI TS 125 141 V5.9.0 (2004-09): Universal Mobile Telecommunications System (UMTS); Base Station Conformance Testing (FDD), (3GPP TS 25.141, Version 5.9.0, Release 5), which is the standard used as a guideline in the design of the MCR850 transceiver. The objective of this application is to obtain FCC initial authorization, under FCC ID: AS5ONEBTS-11, for operation in the Universal Mobile Telecommunications System (UMTS) with a single 5 MHz emission bandwidth carrier (4M10F9W) set to a maximum power level at the antenna terminal of 40 Watts (3-second), over the entire Cellular Frequency Spectrum 869-894 MHz. The UMTS850 UMTS-CDMA Transceiver System (850) consists of the principle RF components: (1) Crystal Reference Oscillator Module (OMA) at 15 MHz, (2) UMTS-CDMA Multi-Carrier CDMA Radio (MCR850), Model BNJ65, which was previously authorized by the Federal Communications Commission under FCC ID: AS5ONEBTS-08, (3) single C2PAM power amplifiers per RF path, and (4) 25 MHz wide Dual Duplex (DDpx), low loss, transmit filters covering the cellular frequency spectrum: 869-894 MHz. These components are considered as a system due to (1) the DDpx filters providing RF feedback to the transceiver in the form of Closed Loop Gain Control (CLGC) to provide constant power over temperature, and (2) Lucent’s proprietary Enhanced Digital Pre-Distortion (EDPD-UL) technology which enables software to communicate between the transceiver, power amplifier and the transmit filter to achieve this goal. As a Transceiver System, all conducted RF characteristics and emissions measurements were performed at the transmit antenna terminal, using a production equipment frame. All testing was performed in the Lucent Technologies, Whippany, NJ, compliance laboratory by F. E. Chetwynd and M. P. Farina during the period June 13 to June 21, 2005; in adherence to a test plan generated by M. P. Farina, in accordance with Lucent’s ISO/TL9000 Registration. All measurement instrumentation utilized were also calibrated in compliance with Lucent’s ISO/TL9000 Registration. The Whippany 3 & 10 Meter Open Area Test Site (OATS) is authorized by the Federal Communications Commission (FCC) under Registration Number: 90770, in compliance with the requirements of Section 2.948 of the Rules of the Commission. Frequency stability measurements were performed by M. Coelho, Lucent Technologies, Swindon, United Kingdom, under the direction of M. P. Farina, and in adherence to the previously cited ISO/TL9000 test plan. A full report is attached to this exhibit. Lucent Technologies Inc. - Proprietary Use pursuant to Company Instructions. Page 2 of 51 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 10: TEST REPORT 67 Whippany Road Whippany, NJ 07981 Subject: Application for FCC Intial Authorization, under FCC ID: AS5ONEBTS-11, Covering the Cellular Michael P. Farina Frequency UMTS-CDMA Transceiver System (850), JW10D0000 Operating Over the Spectrum 869-894 MHz with Telephone: 973-386-4344 a 5 MHz Carrier Emission Bandwidth. [email protected] June 22, 2005 TEST REPORT INTRODUCTION: The exhibits presented in this test report demonstrate that the Lucent Technologies’ Cellular Frequency UMTS-CDMA Transceiver System (850), which is designed to operate in the Lucent UMTS Flexent® OneBTS™ 850 MHz Wireless Base Station, is in full compliance with all requirements of the Rules of the Commission as specified in the Code of Federal Regulations (CFR), Title 47 – Telecommunication; Part 22, Subpart H – Cellular Radiotelephone Service; Section 22.917 - Emission Limitations for Cellular Equipment; effective October 1, 2004. All testing was performed in accordance with CFR 47, Part 2, Subpart J – Equipment Authorization Procedures; effective October 1, 2004. It also demonstrates compliance with the spurious emissions limitations specified in ETSI TS 125 141 V5.9.0 (2004-09): Universal Mobile Telecommunications System (UMTS); Base Station Conformance Testing (FDD), (3GPP TS 25.141, Version 5.9.0, Release 5). This standard was the guideline used in the design of the MCR850 transceiver. The objective of this application is to obtain initial FCC authorization, under FCC ID: AS5ONEBTS-11, for operation in the Universal Mobile Telecommunications System (UMTS) with a single 5 MHz emission bandwidth carrier (4M10F9W) set to a maximum power level at the antenna terminal of 40 Watts (3-second), over the Cellular Frequency Spectrum 869-894 MHz. The UMTS850 Transceiver System consists of the principle RF components: (1) Crystal Reference Oscillator Module (OMA) at 15 MHz, (2) UMTS-CDMA Multi-Carrier CDMA Radio (MCR850), Model BNJ65, which was previously authorized by the Federal Communications Commission under FCC ID: AS5ONEBTS-08, (3) single C2PAM power amplifier per RF path, and (4) 25 MHz wide Dual Duplex (DDpx), low loss, transmit filters covering the cellular frequency spectrum: 869-894 MHz. These components are considered as a system due to (1) the DDpx filters providing RF feedback to the transceiver in the form of Closed Loop Gain Contr…

Text truncated - open the document above for the full version.

Page 1 of 4 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 3: FCC REQUIRED INFORMATION (PART 2.1033) The following information is presented in the content and format requested by the FCC: Section 2.1033 (c)(1): The full name and mailing address of the manufacturer of the device and the applicant for certification. Manufacturer: Lucent Technologies 6200 E Broad St Columbus, OH 43213-1569 U S Applicant: Lucent Technologies 101 Crawfords Corner Road, Holmdel, NJ 07733 Attention: Theresa I. Deaver Section 2.1033(c)(2): FCC Identifier AS5ONEBTS-11 Section 2.1033(c)(4): Type or types of emission: 4M10F9W Section 2.1033(c)(5): Frequency range Transmit: 869–894 MHz Section 2.1033(c)(6): Range of operating power values or specific operating power levels, and description of any means provided for variation of operating power. Lucent Technologies’ UMTS-CDMA Transceiver System (850), which is incorporated into the UMTS Flexent® OneBTS™ 850 MHz wireless base station, is the subject of this application for authorization by the Federal Communications Commission under the new FCC ID: AS5ONEBTS-11. The UMTS850 Transceiver System consists of the principle RF components: (1) Crystal Reference Oscillator Module (OMA) at 15 MHz, (2) UMTS-CDMA Multi-Carrier CDMA Radio (MCR850), Model BNJ65, which was previously authorized by the Federal Communications Commission under FCC ID: AS5ONEBTS-08, (3) P2PAM power amplifier, and (4) 25 MHz bandwidth Dual Duplex (DDpx) transmit filter covering the cellular frequency spectrum 869 – 894 MHz. These components are considered as a system due to the DDpx filters providing RF feedback to the transceiver in the form of Closed Loop Gain Control (CLGC) to provide constant power with over temperature and Lucent’s proprietary Enhanced Digital Pre-Distortion (EDPD-UL) technology which enables software to communicate between the transceiver, power amplifier and the transmit filter to achieve this goal. This UMTS850 Transceiver System is designed to operate in Lucent Flexent™ OneBTS™ UMTS/CDMA 850 MHz wireless base station. The MCR850 can operate for both multi-carrier CDMA and single carrier UMTS technologies; the subject of this request for certification is operation in the Universal Mobile Telecommunications System (UMTS) for a single 5 MHz emission bandwidth UMTS carrier (4M10F9W), The UMTS feature was developed for the North America Region (NAR) deployment, and is also known as Wideband CDMA (W-CDMA). The transceiver can be converted from CDMA to UMTS (or UMTS to CDMA) by software alone, which can be performed at the installation site. There are no physical, hardware or circuit changes to the transceiver. The subject of this application is UMTS. Page 2 of 4 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 3: FCC REQUIRED INFORMATION (PART 2.1033) - continued The maximum rated output power at the antenna terminal of 40 Watts (+46 dBm), 3-second average, per 5 MHz emission bandwidth carrier. Power adjustment is software controlled , using a digital signal to set and adjust voltage variable attenuators in the MCR850 transceiver. The range of attenuation control is 0 - 18 dB maximum, with a resolution of 0.05 dB. Section 2.1033(c)(7): Maximum power rating as defined in the applicable part (s) of the rules. The maximum power rating of the Lucent UMTS Flexent™ OneBTS™ 850 MHz wireless base station, UMTS-CDMA Transceiver System (850) has a maximum rated output power at the base station transmit antenna terminal of 40 Watts (+46 dBm), 3-second average, corresponding to a single 5 MHz emission bandwidth UMTS carrier with QPSK modulation. Section 2.1033 (c)(8): The dc voltages applied to and the dc currents into the several elements of the final radio frequency amplifying device for normal operation over the power range. The dc voltage applied to the UMTS Flexent™ OneBTS™ 850 MHz wireless base station equipment frame is nominally +24 Vdc; the equipment is rated to operate over the range +19-30 Vdc with a typical setting of +26.5 Vdc and a maximum input current of 75 Adc. The nominal dc voltage and range of dc currents input to a single UMTS 850 MHz Power Amplifier, C2PAM, of the UMTS-CDMA Transceiver System (850) is summarized as follows: Single C2PAM Power Amplifier Input Voltage Maximum Input Current: No RF Power Maximum Input Current: At Rated RF Power +19.0 Vdc 11.14 Adc 27.1 Adc +30.0 Vdc 7.11 Adc 16.89 Adc Section 2.1033 (c)(8): Tune-up procedure over the power range, or at specific operating power levels. The Lucent UMTS Flexent™ OneBTS™ 850 MHz wireless base station, UMTS-CDMA Transceiver System (850), subject of this request for certification under FCC ID: AS5ONEBTS-11, can not be “tuned-up” by the user. There are no user tune-up features. All tuning is performed by the manufacturer during, and as part of, the manufacturing process. Section 2.1033 (c)(10) A description of all circuitry and devices for determining and stabilizing frequency. The Lucent UMTS/W-CDMA Flexent™ OneBTS™ 850 MHz wireless base station, incorporating the UMTS-CDMA Transceiver System (850), which utilizes a 5 MHz carrier emission bandwidth, is designed to operate in the cellular frequency spectrum 869-894 MHz. Frequency stability of the carrier frequency is achieved with an accuracy better than the rated ± 0.05 ppm by the 15 MHz reference frequency generated by a stable Crystal Oscillator Module (OMA) plus proprietary phase locked loop (PLL) circuitry. Page 3 of 4 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 3: FCC REQUIRED INFORMATION (PART 2.1033) - continued Section 2.1033 (c)(10): Description of circuitry and devices for suppression of spurious radiation. Spurious emissions radiated from the UMTS Flexent™ OneBTS™ 850 MHz wireless base station equipment frame are suppressed by implementing sound Electromagnetic Compatibility (EMC) design practices extending from the circuit board level to the system level: 1) grounded RF shielding on coaxial cables, 2) grounded RF sh…

Text truncated - open the document above for the full version.

Page 1 of 5 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 6: TEST SET UP PHOTOGRAPHS The photographs in this exhibit show the test equipment configuration for each test performed. Lucent UMTS850 Flexent® OneBTS™ 850 MHz Wireless Base Station, incorporating the UMTS-CDMA Multi-Carrier CDMA Radio (MCR850), BNJ65; the C2PAM power amplifier; and the 25 MHz wideband, low loss, Dual Duplex (DDpx) bandpass filters covering the cellular frequency spectrum 869-894 MHz. TEST: Measurement of RF Power Output Measurement of Modulation Characteristics Measurement of Occupied Bandwidth Measurement of Spurious Emissions at the Antenna Terminals View: UMTS Equipment Frame Front View, Showing Test Configuration for Measuring Emissions and RF Characteristics Conducted to the Antenna Terminal . Page 2 of 5 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 6: TEST SET UP PHOTOGRAPHS View: UMTS Equipment Frame Rear View, Showing Test Configuration for Measuring Emissions and RF Characteristics Conducted to the Antenna Terminal . Page 3 of 5 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 6: TEST SET UP PHOTOGRAPHS TEST: Measurement of Radiated Spurious Emissions View: UMTS Equipment Frame Front View, Showing Test Configuration in the Whippany Semi-Anechoic Chamber. Page 4 of 5 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 6: TEST SET UP PHOTOGRAPHS TEST: Measurement of Frequency Stability View: UMTS 850 Equipment Frame Front View, Showing Test Configuration Utilized for the Measurement of Frequency Stability Temperature/Environmental Chamber Internal View Showing Equipment Frame Under Test (EUT). Page 5 of 5 APPLICANT: LUCENT TECHNOLOGIES FCC ID: AS5ONEBTS-11 EXHIBIT 6: TEST SET UP PHOTOGRAPHS TEST: Measurement of Frequency Stability View: UMTS 850 Equipment Frame Front View, Showing Test Configuration Utilized for the Measurement of Frequency Stability Temperature/Environmental Chamber External View Showing Test and Measurement Equipment Set-up.