AS5ONEBTS-13C2PAM POWER AMPLIFIER MODULE

APPLICANT: Lucent Technologies Exhibit10 FCC ID: AS5ONEBTS-13 Exhibit 9 Section 2.1033 (c)(12) PHOTOGRAPHS OF EQUIPMENT Photographs (8 x 10) of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. Insofar as these requirements are met by photographs or drawings contained in instruction manuals supplied with the certification request, additional photographs are necessary only to complete the required showing. Response: The following pages contain the required photographs of the C2PAM AS5ONBTS-13 amplifier, subject of this application, showing the following external views: 1) Front view of the C2PAM 2) Rear view of the C2PAM 3) Side View with cooling fins 4) Front view of the Flexent® OneBTS™ CDMA Modular Cell 4 Base Transceiver Station Page 1 of 5 APPLICANT: Lucent Technologies Exhibit10 FCC ID: AS5ONEBTS-13 AS5ONBTS-13 C2PAM 4 cm Amplifier Front View 22cm AS5ONEBTS-13 C2PAM Rear View Page 2 of 5 APPLICANT: Lucent Technologies Exhibit10 FCC ID: AS5ONEBTS-13 AS5ONEBTS-06 P2PAM Side View Page 3 of 5 APPLICANT: Lucent Technologies Exhibit10 FCC ID: AS5ONEBTS-13 AS5ONEBTS-13 C2PAM Side View with Cooling Fins Page 4 of 5 APPLICANT: Lucent Technologies Exhibit10 FCC ID: AS5ONEBTS-13 AS5ONEBTS-13 P2PAM Front view of the Flexent® OneBTS™ CDMA PCS Modular Cell 4 Compact AS5ONEBTS-13 C2PAM Amplifier AS5ONEBTS-08 MCR850 Radio Page 5 of 5

APPLICANT: Lucent Technologies Exhibit 8 FCC ID: AS5ONEBTS-13 EXHIBIT 8 Section 2.1033 (c)(11) EQUIPMENT IDENTIFICATION LABEL A photograph of the equipment identification plate or label showing the information to be placed theron. Response: The equipment label affixed to the C2PAM AS5ONEBTS-13 power amplifier will contain the following information. The photo showing the label placement is given in this exhibit as well. Lucent Technologies C2PAM Power Amplifier Module FCC ID:AS5ONEBTS-13 Page 1 of 2 APPLICANT: Lucent Technologies Exhibit 8 FCC ID: AS5ONEBTS-13 Photograph of Label Placement The left side view of the AS5ONEBTS-13 C2PAM amplifier is attached here. Rear AS5ONEBTS-13 Label Placement Front Page 2 of 2

APPLICANT: Lucent Technologies FCC ID: AS5ONEBTS-13 Exhibit 4 Section 2.1033 (c)(8): The dc voltages applied to and the dc currents into several elements of final radio frequency amplifying device for normal operation over the power range. Response The Flexent C2PAM Cellular transmit amplifier module has a normal operating input voltage of 24 VDC, and will operate fully within specifications with an input voltage of 19 VDC to 30 VDC. The amplifier operates at approximately 12% efficiency. The nominal dc voltage and range of dc current input to a single Flexent C2PAM Cellular power amplifier module is summarized below. Input Voltage Single C2PAM Minimum Single C2PAM Maximum Input Current Input Current +24 Vdc 5.4 Amps dc 20 Amps dc Section 2.1033 (c)(8): Tune-up procedure over the power range, or at specific operating levels. Response: The Lucent Technologies C2PAM can not be “tuned-up” by the user. There are no user tune-up Features. All tuning is performed by the manufacturer during, and as part of, the manufacturing Process. Page 1 of 1

APPLICANT: Lucent Technologies FCC ID: AS5 ONEBTS-13 EXHIBIT 13 TEST REPORT This test report presents the measurement data required by the Department for certifying the Flexent C2PAM Cellular transmit amplifier, subject of this application, under FCC ID: AS5 ONEBTS-13. All the testing was performed during the period of April 11 to May 20, 2005. The measurement results have demonstrated that Lucent Technologies Flexent C2PAM Cellular RF power amplifier is in full compliance with the Rules of the Department. For some of the required measurements where FCC Parts 2 and 22 did not give specific requirements, TIA/EIA-97-D’s requirements were used in the report, which are almost identical to the 3GPP2 C.S0010-A v1.0’s requirements. Page 1 of 37 APPLICANT: Lucent Technologies FCC ID: AS5 ONEBTS-13 SUBEXHIBIT 13.1 SECTION 2.1033 (c )(14): REQUIRED MEASUREMENT DATA The required measurement data is presented in the following exhibits as follows: SUBEXHIBIT 10.2 Section 2.1046 Measurements Required: RF Power Output SUBEXHIBIT 10.3 Section 2.1049 Measurements Required: Occupied Bandwidth SUBEXHIBIT 10.4 Section 2.1051 Measurements Required: Spurious Emissions at Antenna Terminal SUBEXHIBIT 10.5 Section 2.1053 Measurements Required: Field Strength of Spurious Radiation SUBEXHIBIT 10.6 Section 2.947 (d) List of Test Equipment Used Page 2 of 37 APPLICANT: Lucent Technologies FCC ID: AS5 ONEBTS-13 SUBEXHIBIT 13.2 Section 2.1046 MEASUREMENT REQUIRED: RF POWER OUTPUT This test is a measurement of the RF power level transmitted at the AS5ONEBTS-13 Flexent C2PAM power transmit amplifier output terminal, as shown in the accompanying test set-up diagram. All the carriers were configured with a combination of Pilot, Sync, Paging and Traffic channels. The Pilot/Sync/Page channels were set up according to the recommended test model for base stations given in TIA/EIA-97-D (Section 6), as shown in the following table. Table 13.2.1. Base Station Test Model, Nominal Type Number of Channels Fraction of Power (linear) Fraction of Power (dB) Comments Pilot 1 0.2000 -7.0 Walsh 0 Sync 1 0.0471 -13.3 Walsh 32, always 1/8 rate Paging 1 0.1882 -7.3 Walsh 1, full rate only Traffic 6 0.09412 each -10.3 each Variable Walsh assignments, full rate only Power measurements were made with a Giga-tronics 8542C Universal Power Meter with 80621A Power Sensor (0.01 – 18 GHz) in the average mode. The test set-up for conducting the RF power output measurement from the Flexent C2PAM power amplifier module is shown in the following figure. Before the testing was started, the Base Station was given a sufficient “warm-up” period as required. The measured channels and results are tabulated in the following table: Table 13.2.2.1 Results of RF Power Output – Single Carrier Cellular Channel No. Frequency (MHz) Cellular Frequency Band C2PAM Output (dBm) 1019 869.88 A” 43.55 37 871.11 A3 43.80 78 872.34 43.77 119 873.57 44.00 160 874.80 A2 43.90 201 876.03 43.72 242 877.26 A1 43.80 283 878.49 43.85 384 881.52 43.76 425 882.75 B1 43.72 466 883.98 43.66 507 885.21 43.80 548 886.44 B2 43.56 589 887.67 43.68 630 888.90 B3 43.67 691 890.73 A’ 43.70 777 893.31 B’ 43.80 Page 3 of 37 APPLICANT: Lucent Technologies FCC ID: AS5 ONEBTS-13 Table 13.2.2.2 RF Power Output – Multi-Carrier Left Edge / Right Edge 2 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37 A”/A3 46.84 48.2 589, 630 B3/B2 46.88 48.7 3 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37, 78 A”/A3/A2 46.92 49.2 548, 589, 630 B3/B2 46.98 49.9 4 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37, 78, 119 A”/A3/A2 47.15 50.8 507, 548, 589, 630 B3/B2 47.08 50.2 5 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37, 78, 119, 160 A”/A3/A2 46.30 41.35 466, 507, 548, 589, 630 B3/B2/B1 46.18 40.2 6 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37, 78, 119, 160, 201 A”/A3/A2/A1 45.39 38.9 425, 466, 507, 548, 589, 630 B3/B2/A1 45.05 37.01 7 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37, 78, 119, 160, 201, 242 A”/A3/A2/A1 44.80 30.40 384, 425, 466, 507, 548, 589, 630 B3/B2/B1 44.78 30.0 8 Carrier Channel No. Cellular Band Power Output (dBm) Power Output (Watts) 1019, 37, 78, 119, 160, 201, 242, 283 A”/A3/A2/A1 44.20 25.80 Results: The above RF power measurements meet TIA/EIA-97-D, Section 4.3.1.3, which specifies that the total power per carrier should remain within +2dB and -4dB of the manufacturer’s rated power. The RF power outputs of the Flexent C2PAM power amplifier module across the Cellular Frequency Band 869.0 – 894 MHz are in full compliance with the Rules of the Commission. Page 4 of 37 APPLICANT: Lucent Technologies FCC ID: AS5 ONEBTS-13 FIGURE 10.2.1 TEST SET-UP FOR MEASUREMENT OF RADIO FREQUENCY POWER OUTPUT CTU – Common Timing Module OM – Oscillator Module MCR850 ID:AS5ONEBTS08 C2PAM Power Amplifier Module ID:AS5ONEBTS13 Tx/Rx Filter 15MHz Modular Cell 4.0 CTU & OM Giga-tronic 8542C Power Meter with 80621A Power Sensor and 30dB RF Attenuator Page 5 of 37 APPLICANT: Lucent Technologies FCC ID: AS5 ONEBTS-13 SUBEXHIBIT 13.4 SECTION 2.1049 : MEASUREMENT REQUIRED: OCCUPIED BANDWIDTH In compliance with Section 2.1049(h), the Flexent C2PAM power amplifier module was configured with a combination of Pilot, Sync, Paging and Traffic channels according to the recommended test model for base stations given in TIA/EIA-97-D (Section 6), as shown in Table 10.2.1. The occupied bandwidth measurements were conducted with the following configurations: 1. the lowest available cellular CDMA channels in the A band, Ch 1019 at 869.88 MHz 2. two to eight contiguous A band channels (A”, A3, A2 and A1), 3. the highest available cellular CDMA channels in the B band, Ch 777 at 893.31 MHz (B’), Ch 691 at 890.73 MHz (A’), and Ch 630 at 888.90 MHz (B3) 4. two to seven contiguous B band channels (B3, B2 and B1) The carrier powe…

Text truncated - open the document above for the full version.