AS5ONEBTS-17UMTS Distributed Base Station 850 MHz

APPLICANT: Alcatel-Lucent Exhibit 7 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 1 of 2 Us Pursuant To Company Instructions EXHIBIT 7: BLOCK DIAGRAM Response: Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz), is the subject of this application for authorization by the Federal Communications Commission under the new FCC ID: AS5ONEBTS-17. Alcatel-Lucent’s Universal Mobile Telecommunications System (UMTS) Distributed Base Station System (850 MHz) is designed to operate in the North America Region (NAR) Cellular Frequency Spectrum 869-890 MHz, with bandwidth of 21 MHz over the A”, A and B Bands. The Distributed Base Station (DBS) can be configured for both single carrier (1S1C) operation at 40 Watts (+46 dBm) and for two carrier (1S2C) operation at 20 Watts (+43 dBm) per carrier with a total composite power of 40 Watts. The RF power rating is based the 3-second average, employing the Aggregate Overload Control (AOC) algorithm. Enhanced Digital Pre-Distortion (EDPD) and Closed Loop Gain Control (CLGC) are features are enabled for each carrier. The carrier power level and frequency are remotely controlled by software. The Distributed Base Station transceiver system, subject of this certification, is comprised of two separate modules interconnected by fiber optic cable: 1) the digital Base Band Unit (BBU), and 2) the Remote Radio Head (RRH). They have the flexibility of being installed either in close proximity to or remotely located from each other. The BBU has the capability of controlling up to 3 remotely located RRH units, via fiber optic cable, and incorporates the digital channel cards, reference oscillator module, T1/E1 and alarm interface, and the RF-to-Optical and Optical-to-RF conversion circuitry. The 850 MHz RRH incorporates the Future Technology Radio (FTR), power amplifier (PA) and passive filter with single transmit (Tx) and diversity receive functionality (Rx0, Rx1). This system complies both with the Federal Communication Commission (FCC) Rules and Regulations (47 CFR Part 22), and with the European Telecommunications Standards Institute (ETSI) 3 rd Generation Partnership Project (3GPP) Technical Specifications TS 25.104 and TS 25.141. This exhibit provides a block diagram showing how the system is interconnected. Block diagrams of the individual components are Alcatel-Lucent Confidential and are contained within documents and exhibits that are requested to be held confidential. APPLICANT: Alcatel-Lucent Exhibit 7 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 2 of 2 Us Pursuant To Company Instructions The UMTS Distributed Base Station Transceiver System (850 MHz): Block Diagram The interconnection between the BBU and RRH is fiber optic cable Base Band Unit (BBU) Digital Circuitry 15 MHz Reference Oscillator Antenna RF Remote Radio Head (RRH) 850 MHz FTR 850 Radio Power Amplifier 21 MHz Band Pass Filter 869-890 MHz

APPLICANT: Alcatel-Lucent FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 1 of 3 Us Pursuant To Company Instructions 67 Whippany Road Subject: Application for Certification under FCC ID: Whippany, NJ 07981 AS5ONEBTS-17, Covering the UMTS/W-CDMA Distributed Base Station System Operating in the Cellular Radiotelephone Service, 869-890 MHz. Rudolf J. Pillmeier Telephone: 973-386-3837 E-Mail: [email protected] October 25, 2007 Mr. Sid Sanders, President Timco Engineering, Inc. 849 N. W. State Road 45, P. O. Box 370 Newberry, Florida 32669 Dear Mr. Sanders: Alcatel-Lucent’s Universal Mobile Telecommunications System (UMTS) Distributed Base Station System (850 MHz) is designed to operate in the North America Region (NAR) Cellular Frequency Spectrum 869- 890 MHz, with bandwidth of 21 MHz over the A”, A and B Bands. The Distributed Base Station (DBS) can be configured for both single carrier (1S1C) operation at 40 Watts (+46 dBm) and for two carrier (1S2C) operation at 20 Watts (+43 dBm) per carrier with a total composite power of 40 Watts. The RF power rating is based the 3-second average, employing the Aggregate Overload Control (AOC) algorithm. Enhanced Digital Predistortion (EDPD) and Closed Loop Gain Control (CLGC) are features that are enabled for each carrier. The single UMTS carrier has a 5 MHz bandwidth, with an emission designator at 4M10F9W, based on measurement of the Necessary Bandwidth. UMTS modulation capability demonstrated includes 1) up to 68 active channels, consisting of 64 voice + 4 control, 2) up to 44 active channels, which include 8 High Speed Downlink Packet Access (HSDPA) channels, and 3) a single active channel Synchronization Channel (SCH). The Distributed Base Station (DBS) system, subject of this certification, is comprised of two separate modules interconnected by fiber optic cable: 1) the digital Base Band Unit (BBU), and 2) the Remote Radio Head (RRH). They have the flexibility of being installed either in close proximity to or remotely located from each other. The BBU has the capability of controlling up to 3 remotely located RRH units, via fiber optic cable, and incorporates the digital channels cards, reference oscillator module, T1/E1 and alarm interface, and the RF-to-Optical and Optical-to-RF conversion circuitry. The 850 MHz RRH incorporates the Future Technology Radio (FTR), power amplifier (PA) and passive filter with single transmit (Tx) and diversity receive functionality (Rx0, Rx1). This system complies both with the Federal Communication Commission (FCC) Rules and Regulations (47 CFR Part 22), and with the European Telecommunications Standards Institute (ETSI) 3 rd Generation Partnership Project (3GPP) Technical Specifications TS 25.104 and TS 25.141. UMTS functionality was developed in accordance to the guidelines of the ETSI TS 25.141 V7.4.0 (2006-06) standard: “Universal Mobile Telecommunications System (UMTS); Base Station Conformance Testing (FDD) (3GPP TS 25.141 version 7.4.0 Release 7)”. The measurement exhibits attached to this application demonstrate full compliance with both FCC Part 22 Subpart H – Cellular Radiotelephone Service and with ETSI TS 25.141, following the procedural requirements specified in FCC Part 2 Subpart J – Equipment Authorization Procedures. The data summarized below is in the form presently used by the Commission’s Radio Equipment List, Equipment Acceptable for Licensing. APPLICANT: Alcatel-Lucent FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 2 of 3 Us Pursuant To Company Instructions Manufacturer Alcatel-Lucent Equipment Identification AS5ONEBTS-17 Rules Part Number Part 22, Subpart H – Cellular Radiotelephone Service Frequency Ranges Transmit 869–890 MHz Output Power 40 Watts (+46 dBm) 3-second average at the Tx antenna terminal Frequency Tolerance ± 0.05 ppm Emission Designator 4M10F9W Attached are the FCC Form 731 (Application for Equipment Authorization – Radio Frequency Devices) and the required measurement data and exhibits specific to this request for initial equipment authorization of the Alcatel-Lucent UMTS, 850 MHz, Distributed Base Station. The technical contact at Alcatel-Lucent will comply with any request for additional information should the need arise. The attached exhibits are assembled and presented in the sequence recommended by Timco Engineering, in accordance with the Table of Contents attachment. Confidentiality is requested for the following exhibits: Exhibit 6: Operational Description (Theory of Operation, Functional Description) Exhibit 8: Schematic Diagrams Exhibit 10: UMTS Operation, Administration and Maintenance (OA&M) Documents. Sincerely, Rudolf J. Pillmeier Technical Manager FCC/EMC Compliance Test Group Whippany, NJ Att. Table of Contents for the UMTS Distributed Base Station System (850 MHz) Certification Report APPLICANT: Alcatel-Lucent FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 3 of 3 Us Pursuant To Company Instructions TABLE OF CONTENTS Cover Letter Request for Confidentiality Exhibit 1: 731 Form Exhibit 2: FCC ID Label Sample and Location Information Exhibit 3: FCC Required Information (Part 2.1033) Exhibit 4: Photographs of the Equipment (Part 2.1033 (c)(12)) Exhibit 5: Test Set Up Photographs Exhibit 6: Operational Description (Theory of Operation, Functional Description) - ALCATEL-LUCENT CONFIDENTIAL Exhibit 7: Block Diagrams - System Exhibit 8: Schematic Diagrams - ALCATEL-LUCENT CONFIDENTIAL Exhibit 9: Test Report Exhibit 10: UMTS – Operation, Administration and Maintenance Documents – ALCATEL-LUCENT CONFIDENTIAL

APPLICANT: Alcatel-Lucent FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 1 of 1 Us Pursuant To Company Instructions 67 Whippany Road Subject: REQUEST FOR CONFIDENTIALITY Whippany, NJ 07981 for FCC ID: AS5ONEBTS-17, Covering the UMTS 850 MHz Distributed Base Station. Rudolf J. Pillmeier Telephone: 973-386-3837 E-Mail: [email protected] October 25, 2007 Mr. Sid Sanders, President Timco Engineering, Inc. 849 N. W. State Road 45, P. O. Box 370 Newberry, Florida 32669 Dear Mr. Sanders: On behalf of Alcatel-Lucent, I hereby request that the following exhibits included in this Application for Certification, under FCC ID: AS5ONEBTS-17, covering the Alcatel-Lucent UMTS 850 MHz Distributed Base Station be maintained as confidential information and not be made available for public inspection at any time. Exhibit 6: Operational Description (Theory of Operation, Functional Description) Exhibit 8: Schematic Diagrams Exhibit 10: UMTS Distributed Base Station (850 MHz) Operation, Administration and Maintenance Documents These exhibits contain Alcatel-Lucent proprietary information that is considered to be trade secrets, with possible patents pending, and the property of Alcatel-Lucent, pursuant to the provisions of Part 0.457(d) of the Commission’s Rules. These exhibits also contain design information that is highly proprietary to Alcatel- Lucent’s contracted manufacturers/suppliers. Exhibits 6 and 8 are highly proprietary and contain critical design information that can not be made available for public inspection. This information is proprietary both to Alcatel-Lucent and to Alcatel-Lucent’s contracted manufacturers/suppliers. The UMTS Distributed Base Station (850 MHz) Operation, Administration and Maintenance documents, included in Exhibit 10, are not furnished to the user, except under very exceptional and very limited circumstances. These manuals contain highly proprietary circuit, equipment and architecture descriptions that must not be made available for public inspection. The cover/title page is explicitly labeled “Unpublished and Not for Publication”. Thank you for your consideration in this matter. Sincerely, Rudolf J. Pillmeier Technical Manager FCC/EMC Compliance Test Group Whippany, NJ

APPLICANT: Alcatel-Lucent Exhibit 3 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 1 of 5 Us Pursuant To Company Instructions EXHIBIT 3: FCC REQUIRED INFORMATION (PART 2.1033) The following information is presented in the content and format requested by the FCC: Section 2.911 (d) Qualification Of Engineers Section 2.911 (d): Technical test data shall be signed by the person who performs or supervises the tests. The person signing the test data shall attest to the accuracy of such data. The Commission may require such person to submit a statement showing that he is qualified to make or supervise the required measurements. Michael P. Farina is a Member of Technical Staff at Alcatel-Lucent, Whippany, NJ, formerly AT&T Bell Laboratories, with 47 years of Professional Experience in Research and Development. He holds a BS in Physics from Upsala College and an MSEE from New Jersey Institute of Technology. During the past 15 years, his expertise was focused on RF Engineering and Regulatory Agency EMC compliance and certification, covering Analog, TDM, CDMA and UMTS technologies. He has submitted numerous Applications for Certification filings to the FCC covering many product variations and evolutions in each of the four technologies. Currently, he is the Lead Engineer for filing UMTS Wireless Base Station products with the FCC. Rudolf J. Pillmeier Technical Manager FCC/EMC Compliance Test Group Whippany, New Jersey Section 2.911 (e)(g) Certification of Technical Test Data Section 2.911 (e) The signatures of the applicant and the person certifying the test data shall be made personally by those persons on the original application; copies of such document may be conformed. Signatures and certifications need not be made under oath. Section 2.911 (g) Signed, as used in this section, means an original handwritten signature; however, the Office of Engineering and Technology may allow signature by any symbol executed or adopted by the applicant with the intent that such symbol be a signature, including symbols formed by computer-generated electronic impulses. I hereby certify that the technical test data are the results of tests either performed or supervised by me. Michael P. Farina Member of Technical Staff FCC/EMC Compliance Test Group Whippany, New Jersey Section 2.1033 (c)(1): The full name and mailing address of the manufacturer of the device and the applicant for certification. Manufacturer: RF Remote Radio Head (RRH): Alcatel Lucent Thailand Ocean Tower 2, 40th Floor, 75/112-115 Sukhumvit 19 Rd. North, Klongtoey, Wattana, 10110 Bangkok, Thailand APPLICANT: Alcatel-Lucent Exhibit 3 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 2 of 5 Us Pursuant To Company Instructions Celestica Thailand Limited 49/18 Leam Chabang Inds. Est., Tungsukhla, Sriracha Chonburi, Thailand. 20230 Digital Base Band Unit (BBU): Celestica 6200 E Broad St Columbus, OH 43213-1569 U S Applicant: Alcatel-Lucent 800 Towers Crescent Drive, Suite 400 Vienna, VA 22182 Attention: Michael D. Garson, Corporate Counsel Section 2.1033(c)(2): FCC Identifier AS5ONEBTS-17 Section 2.1033(c)(4): Type or types of emission: 4M10F9W Section 2.1033(c)(5): Frequency range Transmit: 869–890 MHz Section 2.1033(c)(6): Range of operating power values or specific operating power levels, and description of any means provided for variation of operating power. Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz), is the subject of this application for authorization by the Federal Communications Commission under the new FCC ID: AS5ONEBTS-17. Alcatel-Lucent’s Universal Mobile Telecommunications System (UMTS) Distributed Base Station System (850 MHz) is designed to operate in the North America Region (NAR) Cellular Frequency Spectrum 869-890 MHz, with bandwidth of 21 MHz over the A”, A and B Bands. The Distributed Base Station (DBS) can be configured for both single carrier (1S1C) operation at 40 Watts (+46 dBm) and for two carrier (1S2C) operation at 20 Watts (+43 dBm) per carrier with a total composite power of 40 Watts. The RF power rating is based the 3-second average, employing the Aggregate Overload Control (AOC) algorithm. Enhanced Digital Pre-Distortion (EDPD) and Closed Loop Gain Control (CLGC) are features that are enabled for each carrier. The carrier power level and frequency are remotely controlled by software. The single UMTS carrier has a 5 MHz bandwidth, with an emission designator at 4M10F9W, based on measurement of the Necessary Bandwidth. UMTS modulation capability demonstrated includes 1) up to 68 active channels, consisting of 64 voice + 4 control, 2) up to 44 active channels, which include 8 High Speed Downlink Packet Access (HSDPA) channels, and 3) a single active channel Synchronization Channel (SCH). The Distributed Base Station (DBS) system, subject of this certification, is comprised of two separate modules interconnected by fiber optic cable: 1) the digital Base Band Unit (BBU), and 2) the Remote Radio Head (RRH). They have the flexibility of being installed either in close proximity to or remotely located from each other. The BBU has the capability of controlling up to 3 remotely located RRH units, via fiber optic cable, and incorporates the digital channel cards, reference oscillator module, T1/E1 and alarm interface, and the RF-to-Optical and Optical-to-RF conversion circuitry. The 850 MHz RRH incorporates the Future Technology Radio (FTR850), power amplifier (PA) and passive filter with single transmit (Tx) and diversity receive functionality (Rx0, Rx1). This system complies both with the Federal Communication Commission (FCC) Rules and Regulations (47 CFR Part 22), and with the European Telecommunications Standards Institute (ETSI) 3 rd Generation Partnership Project (3GPP) Technical Specifications TS 25.104 and TS 25.141. APPLICANT: Alcatel-Lucent Exhibit 3 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 3 of 5 Us Pursuant To Company Instructions EXHIBIT 3: FCC REQUIR…

Text truncated - open the document above for the full version.

APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 1 of 6 EXHIBIT 4: PHOTOGRAPHS OF THE EQUIPMENT Section 2.1033 (c)(12): Photographs of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. The UMTS Distributed Base Station (850 MHz) transceiver system, subject of this certification, is comprised of two separate modules interconnected by fiber optic cable: 1) the digital Base Band Unit (BBU), and 2) the RF Remote Radio Head (RRH). They have the flexibility of being installed either in close proximity to or remotely located from each other. The BBU has the capability of controlling up to 3 remotely located RRH units, via fiber optic cable, and incorporates the digital channel cards, reference oscillator module, T1/E1 and alarm interface, and the RF-to-Optical and Optical-to-RF conversion circuitry. The 850 MHz RRH incorporates the Future Technology Radio (FTR850), power amplifier (PA) and passive filter with single transmit (Tx) and diversity receive functionality (Rx0, Rx1). Photographs of the system equipment assembly and configuration and of the individual BBU and RRH components are shown in this exhibit. View Number 1: The RRH and BBU interconnected by fiber optic cable as a system. The RRH is floor mounted on a stand typical of installation. The BBU is an indoor model intended for 19” rack mounting. This is the EMC test lab setup and configuration for conducted emissions measurement. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 2 of 6 View Number 2: RRH removed from the floor stand to show the enclosure rear and face plate view. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 3 of 6 View Number 3: RRH removed from the floor stand to show the enclosure rear and antenna terminal view. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 4 of 6 View Number 4: RRH enclosure opened. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 5 of 6 View Number 5: BBU top, front and right side view showing 19” rack mounting brackets installed. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 6 of 6 View Number 6: BBU with cover remover.

APPLICANT: Alcatel-Lucent Exhibit 2 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 1 of 4 Us Pursuant To Company Instructions EXHIBIT 2: FCC ID LABEL SAMPLE AND LOCATION INFORMATION SECTION 2.1033(c) (11) also SECTION 2.925 (a) (1) A photograph or drawing of the equipment identification plate or label showing the information to be placed thereon. The Alcatel-Lucent UMTS Distributed Base Station (850 MHz) system, subject of this certification, is comprised of two separate modules interconnected by fiber optic cable: 1) the digital Base Band Unit (BBU), and 2) the Remote Radio Head (RRH). They have the flexibility of being installed either in close proximity to or remotely located from each other. The BBU has the capability of controlling up to 3 remotely located RRH units, via fiber optic cable, and incorporates the digital channel cards, reference oscillator module, T1/E1 and alarm interface, and the RF-to-Optical and Optical-to-RF conversion circuitry. The 850 MHz RRH incorporates the Future Technology Radio (FTR), power amplifier (PA) and passive filter with single transmit (Tx) and diversity receive functionality (Rx0, Rx1). Due to displayable space limitations, each of the two separate equipment units will have their respective labels incorporated onto a single conspicuously displayed label. The RF Remote Radio Head will display the Part 2, Subpart J, Section 2.925 FCC Identifier Label “FCC ID: AS5ONEBTS-17”. In addition, both the RF RRH and the digital Base Band Unit (BBU) will display the required Part 15, Section 15.19 label statement “This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.” Faceplate View of the RF Remote Radio Head Showing the Label Placement Label Location The RF Remote Radio Head label drawing is attached. APPLICANT: Alcatel-Lucent Exhibit 2 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 2 of 4 Us Pursuant To Company Instructions Top View of the Digital Base Band Unit Showing the Label Placement Label Location The digital Base Band Unit label drawing is attached. APPLICANT: Alcatel-Lucent Exhibit 2 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 3 of 4 Us Pursuant To Company Instructions RF Remote Radio Head Label Drawing Power DC Input: 24V 18.2A SELV Source Manufactured By Alcatel-Lucent 849064068 ER_0201_0012 SD-2R614-01 For Operating Temperature Ratings Reference The Site Preparation Document apply serial/ba rcode label he re area for system text 9341 RRH 40W 850 MHz9341 RRH 40W 1900 MHz This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. INFORMATION TECHNOLOG Y EQUIPMENT 97B4 area for FCC ID text area for UL These labels are to be applied to the above label to identify MHz and when certifications have been received FCC ID: AS5ONEBTS-17 area for FCC text COMCODE: 849064068 ISSUE#: 4 WORK#: 4IDEAL JACOBS: ISO 9001:2000, 14001:2004 REGISTERED APPLICANT: Alcatel-Lucent Exhibit 2 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 4 of 4 Us Pursuant To Company Instructions Digital Base Band Unit (BBU) Label Drawing

APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 1 of 6 EXHIBIT 4: PHOTOGRAPHS OF THE EQUIPMENT Section 2.1033 (c)(12): Photographs of the equipment of sufficient clarity to reveal equipment construction and layout, including meters, if any, and labels for controls and meters and sufficient views of the internal construction to define component placement and chassis assembly. The UMTS Distributed Base Station (850 MHz) transceiver system, subject of this certification, is comprised of two separate modules interconnected by fiber optic cable: 1) the digital Base Band Unit (BBU), and 2) the RF Remote Radio Head (RRH). They have the flexibility of being installed either in close proximity to or remotely located from each other. The BBU has the capability of controlling up to 3 remotely located RRH units, via fiber optic cable, and incorporates the digital channel cards, reference oscillator module, T1/E1 and alarm interface, and the RF-to-Optical and Optical-to-RF conversion circuitry. The 850 MHz RRH incorporates the Future Technology Radio (FTR850), power amplifier (PA) and passive filter with single transmit (Tx) and diversity receive functionality (Rx0, Rx1). Photographs of the system equipment assembly and configuration and of the individual BBU and RRH components are shown in this exhibit. View Number 1: The RRH and BBU interconnected by fiber optic cable as a system. The RRH is floor mounted on a stand typical of installation. The BBU is an indoor model intended for 19” rack mounting. This is the EMC test lab setup and configuration for conducted emissions measurement. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 2 of 6 View Number 2: RRH removed from the floor stand to show the enclosure rear and face plate view. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 3 of 6 View Number 3: RRH removed from the floor stand to show the enclosure rear and antenna terminal view. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 4 of 6 View Number 4: RRH enclosure opened. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 5 of 6 View Number 5: BBU top, front and right side view showing 19” rack mounting brackets installed. APPLICANT: Alcatel-Lucent Exhibit 4 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Us Pursuant To Company Instructions Page 6 of 6 View Number 6: BBU with cover remover.

APPLICANT: Alcatel-Lucent Exhibit 3 FCC ID: AS5ONEBTS-17 Alcatel-Lucent – Proprietary Page 3 of 5 Us Pursuant To Company Instructions EXHIBIT 3: FCC REQUIRED INFORMATION (PART 2.1033) - continued The maximum rated output power at the antenna terminal is 40 Watts (+46 dBm), 3-second average, per 5 MHz carrier emission bandwidth. Power adjustment is software controlled , using baseband digital scaling to set and adjust voltage variable attenuators in the transceiver. A full discussion of the power control and adjustment is contained in the documents requested to be held confidential. Section 2.1033(c)(7): Maximum power rating as defined in the applicable part (s) of the rules. The maximum power rating of Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz), at the base station transmit antenna terminal, is 40 Watts (+46 dBm), 3-second average, employing the Aggregate Overload Control (AOC) algorithm. Section 2.1033 (c)(8): The dc voltages applied to and the dc currents into the several elements of the final radio frequency amplifying device for normal operation over the power range. The dc voltage applied to Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz) is nominally +24 Vdc. The final radio frequency amplifying device is the power amplifier (PA) incorporated into the RF Remote Radio Head (RRH) module. The maximum rated power at the antenna terminal is 46.0 dBm, which corresponds to the maximum rated power at the PA output terminal of 47.9 dBm. At this power level, the PA nominal voltage and current rating is +31.0 Vdc ± 0.5 Vdc at 6.7 Adc. The worst case maximum current, in event of a 1-dB overdrive condition, could have an excursion up to 8.87 Adc. Section 2.1033 (c)(9): Tune-up procedure over the power range, or at specific operating power levels. Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz), subject of this request for certification under FCC ID: AS5ONEBTS-17, can not be “tuned-up” by the user. There are no user tune-up features. All tuning is performed by the manufacturer during, and as part of, the manufacturing process. Section 2.1033 (c)(10) A description of all circuitry and devices for determining and stabilizing frequency. Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz), incorporating the Future Technology Radio (FTR 850), with a 5 MHz carrier emission bandwidth, is designed to operate in the cellular frequency spectrum 869-890 MHz. The frequency is determined by the up-conversion of digital baseband signals to IF frequencies. Frequency stability of the carrier frequency is achieved with an accuracy better than the rated ± 0.05 ppm by the 15 MHz reference frequency generated by a stable Crystal Oscillator Module (OMA) plus proprietary phase locked loop (PLL) circuitry.

APPLICANT: Alcatel-Lucent Exhibit 9 FCC ID: AS5ONEBTS-17 Test Report Alcatel-Lucent – Proprietary Page 1 of 29 Us Pursuant To Company Instructions EXHIBIT 9: TEST REPORT SYNOPSIS The test report attached to this exhibit demonstrates that the Alcatel-Lucent Cellular Frequency UMTS Distributed Base Station Transceiver System (850), is in full compliance with all requirements of the Rules of the Commission as specified in the Code of Federal Regulations (CFR), Title 47 – Telecommunication; Part 22, Subpart H – Cellular Radiotelephone Service; Section 22.917 - Emission Limitations for Cellular Equipment; effective October 1, 2006. All testing was performed in accordance with CFR 47, Part 2, Subpart J – Equipment Authorization Procedures;effective October 1, 2006. It also demonstrates compliance with the spurious emissions limitations specified in ETSI TS 125 141 V7.4.0 (2006-06): Universal Mobile Telecommunications System (UMTS); Base Station Conformance Testing (FDD), (3GPP TS 25.141, Version 7.4.0, Release 7), which is the standard used as a guideline in the design of the Distributed Base Station transceiver system. The objective of this application is to obtain FCC initial authorization, under FCC ID: AS5ONEBTS-17, for operation in the Universal Mobile Telecommunications System (UMTS) with a single 5 MHz emission bandwidth carrier (4M10F9W) set to a maximum power level at the antenna terminal of 40 Watts (3-second), over 21 MHz of the Cellular Frequency Spectrum 869-890 MHz. Alcatel-Lucent’s wireless UMTS Distributed Base Station Transceiver System (850 MHz), is the subject of this application for authorization by the Federal Communications Commission under the new FCC ID: AS5ONEBTS-17. Alcatel-Lucent’s Universal Mobile Tel…

Text truncated - open the document above for the full version.