ASU-CRU0100Savant Remote

Savant Remote FCC Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC and IC Identifier For Savant Remote This device electronically displays the FCC declaration of conformity logo as well as the FCC and IC identifier. This information can be found on the device by accessing: Main Menu->Settings->About. Industry Canada Statement  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.  This Class B digital apparatus complies with Canadian ICES-003.  Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.  Cet appareil est conforme à la norme RSS-310 d'Industrie Canada. L'opération est soumise à la condition que cet appareil ne provoque aucune interférence nuisible.  This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. The County Code Selection feature is disabled for products marketed in the US/Canada.  Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées. La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada.

REMOTE QUICK START GUIDE Search for Savant in your app store and look for this icon. 2 ENSURE YOUR HOST IS ALREADY SET UP A Savant Host ™ is required to connect to the Remote. A solid green light indicates that the Host is connected to your Wi - Fi ® network. If you need help setting up your Host, please refer to the Host Quick Start Guide. THANKS FOR PURCHASING A SAVANT REMOTE. HERE’S HOW TO GET STARTED: 1 DOWNLOAD THE SAVANT APP ™ The Savant App is available for Apple and Android devices. Upon download, the app will walk you through the rest of your setup. If you need additional help, visit savant.com / support. CHARGE YOUR REMOTE Place your Remote in the Base. As long as you’re nearby, your app should recognize the Remote and will prompt you to connect it to the system. If you do not receive a prompt, tap the + icon in the Devices section of the Savant App. PLUG IN THE BASE Insert one end of the micro-USB power cord into the port located at the back of the Remote Base and the other end into the power adaptor, then plug the adaptor into a power outlet. The Base should be located within line of sight of your TV. 34 5 PLACE YOUR BLASTER If your entertainment devices are out of the line of sight of your Remote Base, you will need to use the included Blaster (included only with Savant Remote + Host package). When devices are on multiple shelves, you will need a Blaster for each shelf. Insert the two AAA batteries to power on the Blaster and place it in front of your devices. PLACE YOUR REMOTE BASE It’s best to place the Remote Base in full view and within 30 feet of all your entertainment devices. 6 TOUCHSCREEN D I S P L AY REMOTE BASE CHANNELVOLUME POWERMICROPHONE VOICE COMMAND 7 USE THE APP TO CONFIGURE YOUR REMOTE Use the Savant App to walk you through the rest of your set up. This will include the connecting of your entertainment devices and a brief voice tutorial. GET TO KNOW YOUR REMOTE The Power button is for turning active entertainment devices off; pressing Power again will turn the devices back on. The Remote will wake up when you lift it out of the Base and will sleep when not in use. To watch your Favorites, just say the name of the channel: “Food Network” or “HBO” To activate a service, say things like “Watch Cable,” “Listen to Sonos,” or “Apple TV” Adjust your environment by saying things like “Brighter,” “Dimmer,” or “Lights Off” Activate a Savant Scene like “Movie Time” by saying its name, or say “Capture” to save the settings of current services into a new scene VOICE COMMAND TIPS You can use your Remote to activate services, scenes, and environmental controls. To use voice control, press and hold the button with the image of a microphone and speak your command clearly. A full list of voice commands is available at savant.com / support. Savant Systems, LLC. 45 Perseverance Way, Hyannis, MA 02601 © 2015 Savant Systems, LLC. All rights reserved. Savant, Savant App, Savant Host, and the Savant logo are trademarks of Savant Systems, LLC. Android, Google, Google Play, and other Google marks are trademarks of Google Inc. Wi - Fi is a registered trademark of Wi - Fi Alliance ® . All other brand names, product names, and trademarks are the property of their respective owners. Product images are simulated and for instructional purposes only. They may differ from the actual products and are subject to change without notice. Savant Systems, LLC reserves the right to change product specifications without notice. Printed in China. Version # 1.0.D Part # HDH6B004010 Follow us: FOR MORE INFORMATION, TUTORIAL VIDEOS, AND FAQ’S, VISIT SAVANT.COM / SUPPORT OR CALL US TOLL - FREE AT 1 - 855 - 5 S AVA N T FCC ID: ASU-CRU0100 IC: 10052A-CRU0100

Page 1 of 10 Report No.: 150923C24 CONSTRUCTION PHOTOS OF EUT Page 2 of 10 Report No.: 150923C24 Page 3 of 10 Report No.: 150923C24 Page 4 of 10 Report No.: 150923C24 Page 5 of 10 Report No.: 150923C24 Page 6 of 10 Report No.: 150923C24 Page 7 of 10 Report No.: 150923C24 Page 8 of 10 Report No.: 150923C24

Model: SAV-CRU-0100-0010 APP ABOUT FLOW

Page 2 of 10 Report No.: 150923C24 Page 3 of 10 Report No.: 150923C24 Page 4 of 10 Report No.: 150923C24 Page 5 of 10 Report No.: 150923C24 Page 6 of 10 Report No.: 150923C24 Page 7 of 10 Report No.: 150923C24 Page 8 of 10 Report No.: 150923C24 Page 9 of 10 Report No.: 150923C24 Page 10 of 10 Report No.: 150923C24

FCC SAR Exclusion Report Report Format Version 5.0.0 Page No. : 1 of 7 Report No. : SA150923C24 Issued Date : Oct. 29, 2015 FCC SAR Exclusion Report Report No. : SA150923C24 Applicant : Savant Systems LLC Address : 45 Perseverance Way Hyannis, MA 02601 USA Product : Savant Remote Brand : Savant FCC ID : ASU-CRU0100 Model No. : SAV-CRU-0100XXXXX (The “X” can be -, A-Z, 0-9, blank and relate only to software.) Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a-2005 / KDB 865664 D01 v01r04 / KDB 865664 D02_v01r02 KDB 447498 D01 v06 Sample Received Date : Sep. 23, 2015 Date of Evaluation : Oct. 27, 2015 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Vera Huang / Specialist Approved By : Gordon Lin / Assistant Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Exclusion Report Report Format Version 5.0.0 Page No. : 2 of 7 Report No. : SA150923C24 Issued Date : Oct. 29, 2015 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement Evaluation .............................................................................................................................................. 6 3.1 Maximum Output Power ............................................................................................................................................... 6 3.2 SAR Testing Exclusions ............................................................................................................................................... 6 4. Information on the Testing Laboratories ............................................................................................................................. 7 Appendix A. Photographs of EUT and Setup FCC SAR Exclusion Report Report Format Version 5.0.0 Page No. : 3 of 7 Report No. : SA150923C24 Issued Date : Oct. 29, 2015 Release Control Record Issue No. Reason for Change Date Issued SA150923C24 Initial release Oct. 29, 2015 FCC SAR Exclusion Report Report Format Version 5.0.0 Page No. : 4 of 7 Report No. : SA150923C24 Issued Date : Oct. 29, 2015 1. Summary of Maximum SAR Value Equipment Class Mode Highest Reported SAR 1g (W/kg) DSS Bluetooth Not Required Note: 1. The SAR limit (Head & Body: SAR 1g 1.6 W/kg) for general population / uncontrolled exposure is specified in FCC 47 CFR part 2 (2.1093) and ANSI/IEEE C95.1-1992. FCC SAR Exclusion Report Report Format Version 5.0.0 Page No. : 5 of 7 Report No. : SA150923C24 Issued Date : Oct. 29, 2015 2. Description of Equipment Under Test EUT Type Savant Remote Brand Name Savant FCC ID ASU-CRU0100 Model Name SAV-CRU-0100XXXXX (The “X” can be -, A-Z, 0-9, blank and relate only to software.) Tx Frequency Bands (Unit: MHz) Bluetooth : 2402 ~ 2480 Uplink Modulations Bluetooth : GFSK, π/4-DQPSK, 8-DPSK Maximum Tune-up Conducted Power (Unit: dBm) Bluetooth : 7.5 Antenna Type PIFA Antenna EUT Stage Identical Prototype Note: 1. The above EUT information is declared by manufacturer and for more detailed features description please refers to the manufacturer's specifications or User's Manual. List of Accessory: Battery Brand Name GETAC Model Name MTT-AHA11122000-1530-0287-AIA Power Rating 3.7Vdc, 2200mAh Type Li-ion BT/WLAN Chip Brand Name Qualcomm Atheros Model Name AR3002 FCC SAR Exclusion Report Report Format Version 5.0.0 Page No. : 6 of 7 Report No. : SA150923C24 Issued Date : Oct. 29, 2015 3. SAR Measurement Evaluation 3.1 Maximum Output Power The maximum conducted power (Unit: dBm) including tune-up tolerance is shown as below. Mode 2.4G Bluetooth Bluetooth DH 7.5 3.2 SAR Testing Exclusions According to KDB 447498 D01, the SAR test exclusion condition is based on source-base…

Text truncated - open the document above for the full version.

Report No.: RF150923C24 Page No. 1 / 42 Report Format Version: 6.1.1 FCC Test Report Report No.: RF150923C24 FCC ID: ASU-CRU0100 Test Model: SAV-CRU-0100XXXXX (The “X” can be -, A-Z, 0-9, blank and relate only to software.) Received Date: Sep. 23, 2015 Test Date: Sep. 24, 2015 ~ Oct. 24, 2015 Issued Date: Oct. 29, 2015 Applicant: Savant Systems LLC Address: 45 Perseverance Way Hyannis, MA 02601 USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location (1): No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF150923C24 Page No. 2 / 42 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Modification Record .............................................................................................................................. 6 3 General Information ................................................................................................................................... 7 3.1 General Description of EUT .................................................................................................................. 7 3.2 Description of Test Modes..................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 9 3.3 Description of Support Units ................................................................................................................ 11 3.3.1 Configuration of System under Test .......................................................................................... 11 3.4 General Description of Applied Standards .......................................................................................... 12 4 Test Types and Results ............................................................................................................................ 13 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 13 4.1.2 Test Instruments ....................................................................................................................... 14 4.1.3 Test Procedures ........................................................................................................................ 15 4.1.4 Deviation from Test Standard ................................................................................................... 15 4.1.5 Test Set Up ............................................................................................................................... 16 4.1.6 EUT Operating Conditions ........................................................................................................ 16 4.1.7 Test Results .............................................................................................................................. 17 4.2 Conducted Emission Measurement .................................................................................................... 21 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 21 4.2.2 Test Instruments ....................................................................................................................... 21 4.2.3 Test Procedures ........................................................................................................................ 22 4.2.4 Deviation From Test Standard .................................................................................................. 22 4.2.5 Test Setup ................................................................................................................................. 22 4.2.6 EUT Operating Condition ...................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST (Below 1GHz) 3 RADIATED EMISSION TEST (Above 1GHz)

FCC SAR Exclusion Report Report Format Version 5.0.0 Issued Date : Oct. 29, 2015 Report No. : SA150923C24 Appendix A. Photographs of EUT and Setup FCC SAR Exclusion Report Report Format Version 5.0.0 Report No. : SA150923C24 <Photographs of EUT>