B8Q315390KRemote Control Transmitter for Garage Door Opener Operation

STEP1: This Wireless Keypad is compatible with all and CODEDODGER® 2 radio equipped GENIE® products. sDrill with 1/16" Drill Bit sPhillips Screwdriver sPencil sMounting Screws INCLUDED sAbility to Control up to three Overhead Door® CODEDODGER®1 or 2 Openers s Simple to Program and Install s PIN Codes can be up to 8 Characters s Low Battery Power Indicator s Stays Programmed During Battery Change s Temporary PIN for Special Purpose Access OPERATING INSTRUCTIONS(KEEP FOR FUTURE REFERENCE) 37257501192 STEP3: Following programming— On your Wireless Keypad: Enter your PIN. OPERATINGDOOROPENERS Proceed to Section 3 - Mounting Instructions. MOUNTINGINSTRUCTIONS The Keypad must be mounted in sight of the Door(s), at least 5 feet above the ground and clear of any moving Door parts. AMount Keypad. (Mounting screws located inside Battery Compartment.) sRemove Battery Cover and batteries. (See Figure 3). s Drill a 1/16” pilot hole for the top mounting screw. sInstall a screw into the drilled hole, leaving a 1/8" gap between the screw head and the wall. (See Figure 2.) sHook the Keypad over the screw. sMark and drill pilot hole and fasten bottom screw. snstall Batteries and Cover. For answers to questions, call 1-800-275-6187 , or visit www.overheaddoor.com Overhead Door Corp., 2501 S State Hwy.,Suite 200, Lewisville, TX 75067. Additional products can be ordered through local Overhead Door® Professional Dealers. To locate a dealer near you, call 1-800-929-DOOR. SECTION 2 SECTION 3 ADDITIONALOPERATIONS SECTION 4 USING ATEMPORARYPIN A temporary PIN allows temporary access to your home by If you have forgotten your PIN or you fear it may have fallen into unauthorized hands, you must erase the old programming. repair persons, meter readers, etc. if you so desire. NOTE DO NOT reprogram the Door Opener (s). s Temporary PIN remains active only until the next time nyour ormal PIN is entered. FORGOTYOURPIN (RESETTING WIRELESS KEYPAD) C HANGINGYOURPIN Enter your current PIN and press . Wall screw head gap Figure 2 FOR CONVENIENCE Program Keypad BEFOREmounting. MULTIPLE FEATURES: T OOLSNEEDED:     ‹2YHUKHDG'RRU&RUSRUDWLRQ FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: s Re-orient or relocate the receiver antenna. s Increase the separation between the opener and receiver. s Connect the opener into an outlet on a circuit different from that to which the receiver is connected. s Consult your local dealer. CHANGINGBAT T E R Y NOTE s If the Door does not move, check the LED on Keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN and try again. s Any Keypad Button will control the Door for 30 seconds after the Door starts moving. s Rapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over. If your garage door opener has a Serial Number sticker which looks like this, in which the first two numbers are 10 or higher, your opener is equipped with CODEDODGER®2. Follow the instructions on this page. Otherwise, follow the instructions on back. sPress in order . sPress . sEnter your PIN (3 to 8 c haracters). s sClose keypad cover and wait 30 seconds. Press . 357 STEP1: C REATINGYOURWIRELESSKEYPADPIN (PERSONALIDENTIFICATIONNUMBER) s s s s s s s s s s 123 Enter your current PIN and press 3 times. Press and hold . Release both buttons. You must now start from the beginning and reprogram your Wireless Keypad. Wile holding press and hold for 5 seconds. Enter your NEW PIN and press. Enter your TEMPORARY PIN and press . s Press the number of the door you wish to operate or . s Press any key to operate the door. s s Press . + AAA - + AAA - If the Keypad backlight does not come on, this indicates the need to replace the batteries. Figure 3 Press here Polarity markings Battery Cover Press in on the front of the battery cover and slide it down off of the Keypad. Remove used batteries and replace s No programming is lost during replacement of batteries. with "AAA." Make sure the batteries are inserted properly using the polarity markings. ATTENTION 2 MODEL AC SR3 OVERHEAD DOOR CORP. FCC ID: B8Q AC SR3 Residential Door Operator IC: 2133A-CSD1D 120V. 60HZ. 5A FOR HELP CALL 1-800-275-6187 OR WWW.OVERHEADDOOR.COM Interchangeable Flip-up Cover available in 3 optional Classic Colors to match your home’s exterior decor GREEN LED indicates Pre-Set to Intellicode® 2 Backlit Keypad for Ease of Use at Night Battery Compartment 2 AAA Batteries (included) Program Button Covers available in: sTan- P/N 37227T sAlmond- P/N 37227U sGray- P/N 37227S sWhite- - P/N 37227R STEP3: O PERATINGONEDOOROPENER ATo open or close the Garage Door. sEnter your PIN. sPress . FOR CONVENIENCE Program Keypad BEFOREmounting. SECTION 1 Proceed to Section 3 - Mounting Instructions. NOTE s If the Door does not move, check the LED on Keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN and try again. s Any Keypad Button will control the Door for 30 seconds after the Door starts moving. s Rapid blinking of the red LED indicates an error. After a few seconds the LED will t…

Text truncated - open the document above for the full version.

Date: 7/1/2014 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, Illinois 60515 Attn: Director of Certification FCC: B8Q315390K To whom it may concern, The following products are electrically and functionally identical with a slight physical variance between the models for branding purposes. The Genie Company Model: GK-A Overhead Door Corporation Model: OKP-A Sincerely, ____ ____James Midyette, P.E.__________ Signature Printed Title: ____RF Engineer____ On behalf of: ____The Genie Company a Division of Overhead Door Corporation Telephone: __330-763-8378____ Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com

Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, Illinois 60515-1082 FCC ID: B8Q315390K Product Name: Dual Frequency Wireless Keypad Model: GK-A and OKP-A Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions’ rules, we hereby request that the following documents be held confidential:  Electrical Schematics and Bills of Material  Theory of Operation Documentation  PCB Assembly and Block Diagram These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 10th Day of June 2014 By: James Midyette, P.E. Signature Printed Title: RF Engineer On behalf of : The Genie Company a Division of Overhead Door Corporation Telephone: 330-763-8378 Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com

Genie Front and Back OHD Front and Back Genie Open View OHD Open View

Figure 1: GK-A Label Location Figure 2: OKP-A Label Location

Figure 1: Internal / PCB Top Figure 2: PCB Top Figure 3: PCB Bottom

DIVERSIFIED T.E.S.T. TECHNOLOGIES, INC. – TEST REPORT Genie Company WAG Ring WAGWR1 Project Number: 6484 This report shall not be reproduced, except in full, without the written approval of DTT, Inc. 1 of 22 D D I I V V E E R R S S I I F F I I E E D D T.E.S.T. TECHNOLOGIES, INC. July, 15 2014 James Midyette Genie Company One Door Drive Mt. Hope, OH 44660 Dear Mr. Midyette: Enclosed is the test report for the NGX WKEP Transmitter 315/390 MHz garage door opener transmitter model GK and OKP tested at our facility, located at 4675 Burr Drive in Liverpool, NY. This facility is on file with the Federal Communications Commission (FCC) per 47 CFR 2.948 (Site File Number 306552) and Industry Canada Site# 3034a-1. We have completed our testing of Emissions to the FCC per 47 CFR Part 15.231 Class C for intentional radiators, and IC RSS 210 for Industry Canada Radio Standards Specification. Thank you for selecting Diversified T.E.S.T. Technologies, Inc. for your testing needs. We look forward to working with you on future projects. Should you have any questions or concerns regarding this report, contact me at 315-457-0245. Please feel free to visit our website at www.dttlab.com. Sincerely, Steve Frierson Technical Associate 4675 Burr Drive ● Liverpool, NY 13088● 1-800-724-6452● FAX: 315-457-0428● 315-457-0245 DIVERSIFIED T.E.S.T. TECHNOLOGIES, INC. – TEST REPORT Genie Company NGX WKEP Transmitter Project Number: 6484 This report shall not be reproduced, except in full, without the written approval of DTT, Inc. 2 of 22 Test Report – Table of Contents COVER PAGE ................................................................................................................................................... 1 TEST INFORMATION ............................................................................................................................... 3 TEST REGULATIONS ............................................................................................................................... 4 EQUIPMENT UNDER TEST (EUT) TESTING OPERATION MODE ................................................ 5 TEST SETUP PHOTOGRAPHS ................................................................................................................ 6 EMISSIONS TESTING CONDITIONS .................................................................................................... 7 TRANSMISSION REQUIREMENTS ....................................................................................................... 8 RATIONALE FOR COMPLIANCE WITH TRANSMISSION REQUIREMENTS ........................... 9 TEST DATA: TRANSMISSION REQUIREMENTS ................................................................. 10 T EST DATA: TRANSMISSION REQUIREMENTS ................................................................. 11 15.205 RESTRICTED BANDS OF OPERATION. .................................................................. 21 15.109 R ADIATED EMISSION LIMITS. ............................................................................. 22 DIVERSIFIED T.E.S.T. TECHNOLOGIES, INC. – TEST REPORT Genie Company NGX WKEP Transmitter Project Number: 6484 This report shall not be reproduced, except in full, without the written approval of DTT, Inc. 3 of 22 T T e e s s t t I I n n f f o o r r m m a a t t i i o o n n Laboratory Diversified TEST Technologies, Inc. 4675 Burr Drive Manufacturer Genie Company Liverpool, NY 13088 One Door Drive, Mt. Hope, OH 44660 Report Issue Date: July 15, 2014 Report Number: 6484-06202014- 15.231 (Edition 1) Project Number: 6484 Date Received: June 5, 2014 Date Tested: June 6, 2014 – June 20, 2014 Product: NGX WKEP Transmitter 315/390 MHz Models: GK and OKP Traceability: Reference standards of measurement have been calibrated by a competent body using standards traceable to NIST. The testing performed by Diversified TEST Technologies, Inc. has shown that the product referenced above complies with the electromagnetic compatibility requirements according to the FCC per 47 CFR Part 15.231, and IC RSS 210 for Industry Canada Radio Standards Specification. The results in this test report apply only to the NGX WKEP 315/390 MHz, Models: GK and OKP. . It is the responsibility of the manufacturer to ensure that the product identification and labeling are in compliance with the applicable standards requirements. The manufacturer is also responsible for ensuring that additional units are manufactured with identical mechanical and electrical characteristics. The equipment listed above conforms to the specified requirements of the test standards listed in the Test Regulations section of this report. Compiled by: Signature: _____________________________ Date: July 15, 2014 Steven Frierson Technical Lab Manager Authorized by: ______________ Signature: _____________________________ Date: July 18, 2014 T T o o m m S S i i m m s s President DIVERSIFIED T.E.S.T. TECHNOLOGIES, INC. – TEST REPORT Genie Company NGX WKEP Transmitter Project Number: 6484 This report shall not be reproduced, except in full, without the written approval of DTT, Inc. 4 of 22 T T e e s s t t R R e e g g u u l l a a t t i i o o n n s s The tests were performed according to the following standards: FCC Part 15.231& IC RSS 210 for Industry Canada RSS Class A Class C FCC Part 15 Class A Class B Certification Verification Summary of Test Data Name of Test Paragraph Number Results Transmission Requirements 15.231 (a) Complies Radiated Emissions 15.231 (b) Complies Occupied Bandwidth 15.231 (c) Complies Frequency Tolerance 15.231 (d) N/A Alternate Field Strength Requirements 15.231 (e) N/A Power line Conducted Emissions 15.207 N/A Note: 1.) The Device does not operate between 40.66 to 40.70 MHz 2.) The Device does not operate at a periodic rate 3.) The Device is battery powered DIVERSIFIED T.E.S.T. TECHNOLOGIES, INC. – TEST REPORT Genie Company NGX WKEP Transmitter Project Number: 6484 This report shall not be reproduced, except in full, without the written approval o…

Text truncated - open the document above for the full version.

DIVERSIFIED T.E.S.T. TECHNOLOGIES, INC. – TEST REPORT Genie Company NGX WKEP Transmitter Project Number: 6484 This report shall not be reproduced, except in full, without the written approval of DTT, Inc. 6 of 22 T T e e s s t t S S e e t t u u p p P P h h o o t t o o g g r r a a p p h h s s 1.1 Radiated Emissions above 1 GHz / Occupied Bandwidth 1.2. Radiated Emissions above 1 GHz