CCKPC0163Low Power Wireless Transceiver

CellComsl™ series Universal a larm CommUniC a tor InstallatIon and programmIng guIde Digital Monitoring Products CellComSL Series Universal Communicator Install/Programming Guide ii FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions. The installer may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402 Stock No. 004-000-00345-4 © 2015 Digital Monitoring Products, Inc. Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Industry Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Caution Notes Throughout this guide you will see caution notes containing information you need to know when installing the communicator. These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you completely read and understand its information. Failing to follow the caution note can cause damage to the equipment or improper operation of one or more components in the system. CellComSL Series Universal Communicator Installation and Programming Guide Digital Monitoring Products iii Table of ConTenTs Table of Contents Description .......................................................................................................................1 What is Included ...............................................................................................................1 System Components .............................................................................1 1.1 Terminals (J9) ........................................................................................................1 Power Connection Terminals ...................................................................................1 Control Panel Standby Power ..................................................................................1 Zones 1-4 ..............................................................................................................1 Dialer Connection ..................................................................................................2 1.2 System Battery Connection (BAT) ............................................................................2 System Battery ......................................................................................................2 1.3 Programming Connection ........................................................................................2 1.4 Tamper ..................................................................................................................3 1.5 Reset Button ..........................................................................................................3 1.6 Load Button ...........................................................................................................3 399 Programming Cable .........................................................................................3 Model 400 USB Flash Module ..................................................................................3 1.7 Backlit Logo ...........................................................................................................3 Mounting the CellComSL Series Communicator ....................................4 2.1 Selecting a Location ...............................................................................................4 Applications ...........................................................................................5 3.1 CID Dialer Connec…

Text truncated - open the document above for the full version.

Page 1 of 2 May 8, 2015 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Digital Monitoring Products, Inc. 2500 North Partnership Boulevard Springfield, MO 65802 Re: Confidentiality for submittal information regarding FCC ID number CCKPC0163 PRODUCT: Low power Transmitters operated under paragraph 15.249 Dear Sirs: Digital Monitoring Products, Inc. requests that the material in the Schematics, Block Diagram, and Operational Description be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. In support of this request, Digital Monitoring Products, Inc. submits the following information. CONFIDENTIAL FILES Conf BlkDia CellComSL.pdf Conf OpDes CellComSL.pdf Conf Schem CellComSL.pdf 1. Identification of the specific information for which confidential treatment is sought: The materials set forth in the Operational Description, block diagram, parts list, and Schematics, which are segregated, from the non-confidential exhibits of the application, are those for which confidentiality is sought. 2. Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission: The proceeding is that involving the application for equipment authorization (certification) under FCC ID No: CCKPC0163 3. Explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged: This material includes a detailed theory of operation, circuit diagrams, and schematic. As such, this material is treated as highly confidential business information. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 913 837-3214 Page 2 of 2 4. Explanation of the degree to which the information concerns a service that is subject to competition: The material for which confidentiality is sought is employed in the design and manufacture of this transmitting equipment that is offered on a highly competitive basis. Customers for this equipment have a variety of competing sources. 5. Explanation of how disclosure of the information could result in substantial competitive harm: Disclosure would, in effect, give away the fruits of the labors of Digital Monitoring Products, Inc.’s engineering personnel, who have designed the equipment and the manufacturing process. Disclosure would also offer competitors additional unwarranted insight into the state of the product development, thereby allowing competitors an advantage, not available to Digital Monitoring Products, Inc. 6. Identification of any measures taken by the submitting party to prevent unauthorized disclosure: The information for which confidential treatment is sought is kept confidential by Digital Monitoring Products, Inc. and not made available to third parties except pursuant to non-disclosure agreements. 7. Identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties: To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. While the general theory of operation of this equipment has been the subject of numerous disclosures in industry and standards groups as well as in rule making proceedings of the FCC, the protection sought is narrowly drawn and pertains to certain specific implementations of this radio technology. 8. Justification of the period during which the submitting party asserts that the material should not be available for public disclosure: This material should not be disclosed for at least 25 years. While improvements in design are made relatively frequently, disclosure of the design information would lead to insights into both design and manufacturing techniques that could have an adverse competitive effect for many years to come. As such, it is important that the design not be made available to unauthorized persons who might attempt to use knowledge of the design to compromise the applications for which the equipment will be employed. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers

January 3, 2008 Federal Communications Commission Equipment Approval Services Post Office Box 358315 Pittsburgh, Pennsylvania 15215-5315 To Whom It May Concern: Please be advised that Digital Monitoring Products, Inc. has authorized Scot Rogers of Rogers Labs, Inc. to act on behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters and submittals. All acts carried out by Scot Rogers of Rogers Labs, Inc. on our behalf shall have the same effects as our own. Rogers Labs, Inc. authorized to receive and exchange data between our company and the Commission. This Authorization is made pursuant to Paragraph 2.911 of FCC Rules CFR 47. This Authorization is in effect until otherwise notified in writing. Best regards, Terry Shelton Product Quality Assurance Manager Digital Monitoring Products, Inc. Lb

May 8, 2015 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Digital Monitoring Products, Inc. Equipment: FCC ID: CCKPC0163 2500 North Partnership Boulevard CORES number: 0009 86 9348 Springfield, MO 65802 FCC Rules: Parts 2 and 15.249 To Whom It May Concern: The form 731 and application have been electronically submitted and any attachments will be up loaded to your web site for use in obtaining a grant of certification. Confidentiality is requested as outlined below. Permanent Digital Monitoring Products, Inc. requests that the material in the Schematics, Block Diagram, and Operational Description be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. A statement of confidentiality will be attached with the application at the time of submittal. Exhibit File Schematics Conf Schem CellComSL.pdf Block diagram Conf BlkDia CellComSL.pdf Operational Description Conf OpDes CellComSL.pdf Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers Rogers Labs, Inc. Enclosures ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214

Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: ExtPho CellComSL Page 1 of 3 External photographs of equipment under test Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: ExtPho CellComSL Page 2 of 3 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: ExtPho CellComSL Page 3 of 3

May 11, 2015 Regarding FCC ID label placement for the Model CellComSLCZ, FCC ID: CCKPC0163 and IC: 5251A-PC0179 applications, DMP wishes to print the information directly onto the device printed circuit board. This location will ensure the end user is always able to view the information before operation. The identifier will be readily viewable upon installation and each time the cover is removed. The equipment is sold and required to be mounted before operation thus exposing the information before operation. This location will help ensure the longevity of the information as this equipment may be in service in harsh environments. Best Regards, Terry Shelton | Director of Technical Design Digital Monitoring Products | dmp.com 417.831.9362 | Fax 417.447.9698 Lb

Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: iComSL SN: ENG 1 FCC ID: CCKPC0179 Louisburg, KS 66053 Test #: 150406 IC: 5251A-PC0179 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: LabelSmpl iComSL Page 1 of 1 ID label and location Label Placement

Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: IntPho CellComSL Page 1 of 1 Internal Photographs

Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: TunPro CellComSL Page 1 of 1 Tune-up Procedure Each unit is evaluated during production and then given pass/fail status based on the measured parameters. The pass/fail threshold is determined by engineering during product development. Compliant samples continue through production and non-compliant units are removed.

NVLAP Lab Code 200087-0 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 12, 2015 Revision 2 File: DMP CellComSL TstRpt 150430 r2 Page 1 of 28 Application Submittal Report FOR FCC And Industry Canada Grant Of Certification FOR Model: CellComSL 908 MHz Low Power Transmitter FCC ID: CCKPC0163 IC: 5251A-PC0163 FOR Digital Monitoring Products, Inc. 2500 North Partnership Boulevard Springfield, MO 65802-6310 Test Report Number: 150430 IC Test Site Registration: 3041A-1 Authorized Signatory: Scot D. Rogers NVLAP Lab Code 200087-0 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 12, 2015 Revision 2 File: DMP CellComSL TstRpt 150430 r2 Page 2 of 28 Engineering Test Report For Application Submittal for Grant of Certification FOR CFR 47, PART 15C - Intentional Radiators Paragraph 15.249 and Industry Canada, RSS-210 License Exempt Intentional Radiator For Digital Monitoring Products, Inc. 2500 North Partnership Boulevard Springfield, MO 65802-6310 Model: CellComSL Low Power Transmitter Frequency Range 908 MHz FCC ID#: CCKPC0163 IC: 5251A-PC0163 Test Date: April 30, 2015 Certifying Engineer: Scot D. Rogers Rogers Labs, Inc. 4405 West 259 th Terrace Louisburg, KS 66053 Telephone/Facsimile: (913) 837-3214 This report shall not be reproduced except in full, without the written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214 NVLAP Lab Code 200087-0 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 12, 2015 Revision 2 File: DMP CellComSL TstRpt 150430 r2 Page 3 of 28 Table Of Contents TABLE OF CONTENTS .................................................................................................. 3 REVISIONS ..................................................................................................................... 4 FORWARD ..................................................................................................................... 5 OPINION / INTERPRETATION OF RESULTS ............................................................... 5 STATEMENT OF MODIFICATIONS AND DEVIATIONS ............................................... 5 EQUIPMENT TESTED .................................................................................................... 6 EQUIPMENT FUNCTION AND CONFIGURATION........................................................ 6 Equipment Configuration.................................................................................................................................... 6 APPLICATION FOR CERTIFICATION ........................................................................... 7 APPLICABLE STANDARDS & TEST PROCEDURES .................................................. 8 EQUIPMENT TESTING PROCEDURES ........................................................................ 8 AC Line Conducted Emission Test Procedure .................................................................................................. 8 Radiated Emission Test Procedure ..................................................................................................................... 8 Diagram 1 Test arrangement for Conducted emissions ....................................................................................... 9 Diagram 2 Test arrangement for radiated emissions of tabletop equipment ...................................................... 10 Diagram 3 Test arrangement for radiated emissions tested on Open Area Test Site (OATS) ........................... 11 TEST SITE LOCATIONS .............................................................................................. 11 LIST OF TEST EQUIPMENT ........................................................................................ 12 UNITS OF MEASUREMENTS ...................................................................................... 13 ENVIRONMENTAL CONDITIONS................................................................................ 13 INTENTIONAL RADIATORS ........................................................................................ 13 Antenna Requirements ...................................................................................................................................... 13 Restricted Bands of Operation .......................................................................................................................... 14 Table 1 Radiated Emissions in Restricted Bands Data ...................................................................................... 14 NVLAP Lab Code 200087-0 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: CellComSL SN: Tx 1 FCC ID: CCKPC0163 Louisburg, KS 66053 Test #: 150430 IC: 5251A-PC0163 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 12, 2015 Revision 2 File: DMP CellComSL TstRpt 150430 r2 Page 4 of 28 Summary of Results for Radiated Emissions in Restricted Bands ................................................................ 14 AC Line Conducted Emissions Procedure ....................................................................................................... 14 Figure 1 AC Line Conducted emissions of EUT line 1 (EUT AC Adapter) ..................................................... 16 Figure 2 AC Line Conducted em…

Text truncated - open the document above for the full version.

Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: iComSL SN: ENG 1 FCC ID: CCKPC0179 Louisburg, KS 66053 Test #: 150406 IC: 5251A-PC0179 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: TSup iComSL Page 1 of 4 Test setup photographs Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: iComSL SN: ENG 1 FCC ID: CCKPC0179 Louisburg, KS 66053 Test #: 150406 IC: 5251A-PC0179 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: TSup iComSL Page 2 of 4 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: iComSL SN: ENG 1 FCC ID: CCKPC0179 Louisburg, KS 66053 Test #: 150406 IC: 5251A-PC0179 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: TSup iComSL Page 3 of 4 Rogers Labs, Inc. Digital Monitoring Products, Inc. 4405 W. 259th Terrace Model: iComSL SN: ENG 1 FCC ID: CCKPC0179 Louisburg, KS 66053 Test #: 150406 IC: 5251A-PC0179 Phone/Fax: (913) 837-3214 Test to: FCC (15.249), RSS-210 Date: May 8, 2015 Revision 1 File: TSup iComSL Page 4 of 4