DZLCX3BLogitech Cordless Precision Controller for XBOX

INSTALLATIONINSTALLATION CORDLESS PRECISION ™ CONTROLLERCORDLESS PRECISION ™ CONTROLLER Logitech ® Logitech ® 1 ENGLISH Install batteries in controller. Remove battery compartment cover, insert batteries into controller, and then replace the cover. One set of batteries provides about 50 hours of operation with vibration motors on (more than 300 hours with motors off). ESPAÑOL Instalación de las pilas en el mando. Quite la tapa del compartimento de las pilas, introduzca las pilas en el mando y vuelva  a colocar la tapa. Cada juego de pilas permite unas 50 horas de uso con los motores de efecto de vibración encendidos (más de 300 horas  con los motores apagados). FRANÇAIS Installation des piles dans le contrôleur. Enlevez le couvercle du logement des piles, insérez les piles dans le contrôleur,  puis replacez le couvercle du logement. Un jeu de piles permet une utilisation de 50 heures avec les moteurs de vibration activés  (plus de 300 heures sans les moteurs). PORTUGUÊS Introduzir as pilhas no controlador. Remova a tampa do compartimento de pilhas, introduza as pilhas no controlador  e recoloque a tampa. Um conjunto de pilhas fornece 50 horas de funcionamento com os motores de vibração ligados (mais de 300 horas  com os motores desligados). ENGLISH Insert receiver connector into controller port of Xbox ® . ESPAÑOL Introduzca el conector del receptor en el puerto del mando de la Xbox ® . FRANÇAIS Insérez le connecteur du récepteur dans le port du contrôleur de la Xbox ® . PORTUGUÊS Insira o conector do receptor na porta do controlador de Xbox ® . 3 ENGLISH Turn on Xbox ® , and then load a game. Receiver Status light blinks slowly. ESPAÑOL Encienda la Xbox ® y cargue el juego. El diodo de estado del receptor parpadea lentamente. FRANÇAIS Allumez la Xbox ® et chargez un jeu. Le témoin d’état du récepteur clignote lentement. PORTUGUÊS Ligue Xbox ® e, em seguida, carregue o jogo. A luz de estado do receptor pisca lentamente. 4 ENGLISH To establish a connection with receiver, press any action button on controller. Receiver Status light turns solid green for 2 seconds  (then off) when connection has been made. If controller does not connect, press Connect button on receiver (see previous figure), and then press  any action button on controller. ESPAÑOL Para establecer una conexión con el receptor, pulse cualquiera de los botones de acción del mando. La luz verde del diodo  de estado del receptor permanece iluminada durante dos segundos (luego se apaga) una vez establecida la conexión. Si el mando no se conecta,  pulse el botón Connect del receptor (véase la figura anterior) y, a continuación, pulse cualquier botón de acción en el mando. FRANÇAIS Pour établir la connexion avec le récepteur, appuyez sur un bouton d’action du contrôleur. Le témoin d’état du récepteur  passe au vert en continu pendant 2 secondes, puis s’éteint, quand la connexion est établie. Si le contrôleur n’établit pas la connexion,  appuyez sur le bouton Connect du récepteur (voir illustration précédente), puis appuyez sur un bouton d’action sur le contrôleur. PORTUGUÊS Para estabelecer uma ligação com o receptor, prima qualquer botão de acção no controlador. A luz de estado do receptor  fica verde durante 2 segundos (depois apaga-se) quando a ligação é estabelecida. Se o controlador não ligar, prima o botão Connect no receptor  (ver a figura anterior) e, em seguida, prima qualquer botão de acção no controlador. 2.4 GHz CORDLESS FREEDOM 2.4 GHz DE LIBERTÉ SANS FIL 2 ENGLISH The controller enters sleep mode after 1) batteries are inserted, 2) when controller has not connected with receiver,  or 3) after 5 minutes of inactivity. Press any action button to activate the controller. ESPAÑOL El mando pasa al modo de suspensión 1) cuando se han introducido las pilas, 2) cuando el mando no se ha conectado  con el receptor, o 3) tras 5 minutos de inactividad. Pulse cualquiera de los botones de acción para activar el mando. FRANÇAIS Le contrôleur se met en veille 1) à l’insertion des piles, 2) quand il n’a pas établi la connexion avec le récepteur ou 3) après  5 minutes d’inactivité. Appuyez sur un bouton d’action pour activer le contrôleur. PORTUGUÊS O controlador entra no modo de suspensão 1) depois da introdução das pilhas, 2) quando o controlador não está ligado  no receptor ou 3) depois de 5 minutos de inactividade. Prima qualquer botão de acção para activar o controlador. ENGLISH Vibration Feedback. On by default. Press Vibration button to turn off vibration feedback (controller vibrates 1 / 2 sec.).  Press Vibration button again to turn on vibration feedback (controller vibrates 2 sec.). Low battery power causes vibration feedback to turn off. ESPAÑOL Efecto de vibración. Activado de manera predeterminada. Pulse el botón Vibration para desactivar el efecto de vibración  (el mando vibra durante 1 / 2 segundo). Pulse el botón Vibration nuevamente para activar el efecto de vibración (el mando vibra durante 2 segundos). Si las pilas tienen poca carga, se desactiva el efecto de vibración. FRANÇAIS Retour des vibrations. Activé par défaut. Appuyez sur le bouton Vibration pour désactiver le retour de vibrations (le contrôleur  vibre pendant une demie-seconde). Appuyez de nouveau sur le bouton Vibration pour activer le retour de vibrations (le contrôleur vibre pendant  deux secondes). Quand la charge des piles est faible, le retour de vibrations se désactive. PORTUGUÊS Reacção de vibração. Activada por predefinição. Prima o botão Vibração para desligar a reacção de vibração (o controlador  vibra por 1 / 2 segundo). Prima o botão Vibração novamente para ligar a reacção de vibração (o controlador vibra por 2 segundos). Quando as pilhas estão fracas, a reacção de vibração é desligada. ® 3 2 4 1 . ENGLISH Controller Mode/Status Light: 1) Normal mode (light off). Triggers and action buttons provide analog pressure input  (i.e., increased pressure on these controls increases action in supported games). ESPAÑOL Modo de m…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

(Fig. 1) FCC ID: DZLCX3B FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. FCC Label

Page 1 Page 2 Page 3 Page 4

FCC ID: DZLCX3B Report No.: RF930212H04 Operational Description The device is a Logitech ® Cordless Precision™ Controller for XBOX™, and employing FHSS (Frequency Hopping Spread Spectrum) modulation with 79 hopping channels in 2.4 GHz Band. The antenna type are Remote: PCB strip antenna and Host: Sheet metal inverted-F antenna and there is no antenna connector used. The other instruction, please have a look at the users manual.

FCC ID: DZLCX3B Report No.: RF930212H041Issued: Feb.25, 2004 FCC TEST REPORT REPORT NO.: RF930212H04 MODEL NO.: C-X3B18 RECEIVED: Feb. 12, 2004 TESTED: Feb. 18 to 23, 2004 APPLICANT:LOGITECH INC. ADDRESS:6505 Kaiser Drive Fremont, CA 94555-3615 ISSUED BY:Advance Data Technology Corporation LAB LOCATION:No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 33 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA or any government agencies. The test results in the report only apply to the tested sample. 0536 ILAC MRA FCC ID: DZLCX3B Report No.: RF930212H042Issued: Feb.25, 2004 TABLE OF CONTENTS 1CERTIFICATION .........................................................................................................................3 2SUMMARY OF TEST RESULTS.................................................................................................4 3GENERAL INFORMATION .........................................................................................................5 3.1GENERAL DESCRIPTION OF EUT............................................................................5 3.2DESCRIPTION OF TEST MODES..............................................................................6 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................6 3.4DESCRIPTION OF SUPPORT UNITS........................................................................7 4TEST PROCEDURES AND RESULTS .......................................................................................8 4.1CONDUCTED EMISSION MEASUREMENT ..............................................................8 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT ...........................................................8 4.1.2TEST INSTRUMENTS ................................................................................................................8 4.1.3TEST PROCEDURES .................................................................................................................9 4.1.4DEVIATION FROM TEST STANDARD .......................................................................................9 4.1.5TEST SETUP ............................................................................................................................10 4.1.6EUT OPERATING CONDITIONS..............................................................................................10 4.1.7TEST RESULTS ........................................................................................................................ 11 4.2RADIATED EMISSION MEASUREMENT .................................................................17 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT ..............................................................17 4.2.2TEST INSTRUMENTS ..............................................................................................................18 4.2.3TEST PROCEDURES ...............................................................................................................19 4.2.4DEVIATION FROM TEST STANDARD .....................................................................................19 4.2.5TEST SETUP ............................................................................................................................20 4.2.6TEST RESULTS ........................................................................................................................21 4.2.7TEST RESULTS ........................................................................................................................22 4.3BAND EDGES MEASUREMENT..............................................................................25 4.3.1LIMITS OF BAND EDGES MEASUREMENT ...........................................................................25 4.3.2TEST INSTRUMENTS ..............................................................................................................25 4.3.3TEST PROCEDURE .................................................................................................................25 4.3.4DEVIATION FROM TEST STANDARD .....................................................................................25 4.3.5EUT OPERATING CONDITION ................................................................................................26 4.3.6TEST RESULTS ........................................................................................................................26 5PHOTOGRAPHS OF THE TEST CONFIGURATION ...............................................................31 6INFORMATION ON THE TESTING LABORATORIES..............................................................33 FCC ID: DZLCX3B Report No.: RF930212H043Issued: Feb.25, 2004 1 CERTIFICATION PRODUCT : Logitech ® Cordless Precision™ Controller for XBOX™ BRAND NAME : Logitech MODEL NO : C-X3B18 TEST ITEM: Engineering Sample APPLICANT : LOGITECH INC. STANDARDS : 47 CFR Part 15, Subpart C (15.249) ANSI C63.4-1992 We, Advance Data Technology Corporation, hereby certify that one sample of the designation has been tested in our facility from Feb. 18 to 23, 2004. The test record, data evaluation and Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample's characteristics under the conditions herein specified. PREPARED BY: , DATE: Feb. 25, 2004 ( Amanda Chu ) APPROVED BY:, DATE: Feb. 25, 2004 ( Eric Lin, Manager ) FCC ID: DZLCX3B Report No.: RF930212H044Issued: Feb.25, 2004 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: 47 CFR Part 15, Subpart C Standard Paragraph Test TypeResultRemark 15.207Conducted Emission TestPASS Minimum passing margin is –1…

Text truncated - open the document above for the full version.

FCC ID: DZLCX3B Report No.: RF930212H0431Issued: Feb.25, 2004 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: DZLCX3B Report No.: RF930212H0432Issued: Feb.25, 2004 RADIATED EMISSION TEST