DZLS00112S-00112

English Safety information WARNING! ELECTRIC SHOCK HAZARD: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO WATER. Read and follow these instructions, heed all warnings, and keep this document for future reference. • Your product is suitable for use in semi-tropical and moderate climates only. Set up your product in accordance with Logitech’s product documentation, and place your product in a stable location so it will not fall and cause product damage or bodily harm. Operate your product only from the low-level, audio line output jack of your computer or audio component. • Do not use your product near water, including dripping or splashing sources (e.g., indoor fountains), or near objects filled with liquids, such as flower vases or fish tanks. • Do not use your product near heat sources (e.g., radiators, heat registers, stoves, open flames, such as lighted candles, or other heat-producing devices, such as audio amplifiers or TVs). • Do not block ventilation openings or push objects into product vents, ports, or slots. Doing so may create an electric shock or fire hazard. Maintain a minimum distance of at least 15 cm (6 inches) around your product for sufficient ventilation. Covering ventilation openings with such items as newspapers, tablecloths, or curtains may impede ventilation and cause a fire. • Do not, under any circumstance, modify your product’s power cord and plug, including the power cord and plug to your product’s power supply, if one has been included. If the plug does not fit into your AC outlet, have a certified electrician replace your obsolete AC outlet. Protect the power cord from being stepped on or pinched, especially where the cord exits the product or plugs into an AC outlet or power strip. • Unplug your product during lightning storms or when it’s not being used for long periods of time. Disconnect your product from the AC outlet by first turning off the product or by placing it in standby mode (see product documentation for more information) before unplugging the product’s power cord from the AC outlet. Your product’s power cord and plug must remain operational at all times, and the AC outlet (receptacle) should be near the product and easily accessible. • Only use approved attachments and accessories specified by Logitech. • Refer all servicing and repair to qualified service personnel. Servicing is required when your product does not operate normally, the power cord/plug has been damaged, the product has been exposed to water, rain, liquid, or moisture, the product has been dropped, or an object has been inserted into a product port or vent. • For portable products or products weighing less than 7 kg (15 lbs), the product label may be found on the product stand, under a lid, or on the bottom of the product itself. • Clean your product using only a dry cloth and no water or liquid. Warning Symbols Explained This symbol is placed on the product to tell you to proceed with CAUTION. Refer to your product documentation before continuing. Find the section in the manual that pertains to the product feature or function referenced by this symbol. This symbol is placed on the product as a WARNING. Access to this area of the product is restricted. Failure to comply could result in an electrical shock hazard. Protect your hearing Listening advice to avoid hearing damage Listening via headphones, earbuds, or headsets at a high volume may cause permanent hearing loss to occur. The louder the volume, the less time is required before your hearing could be affected. To establish a safe volume level: • Start your equipment with the volume control at its lowest setting. • Slowly increase the sound until you can hear it comfortably and clearly, and without distortion. • Avoid setting the volume at a level that prevents you from hearing conversations and other similar noises around you. Once you have established a comfortable sound level, leave it there. If you experience a ringing in your ears, discomfort or muffled speech, reduce the volume or stop listening and have your hearing checked. See the product support page on the Logitech website www.logitech.com for additional information. Disposal guidelines at product end of life Some Logitech products use non-serviceable, nickel-metal hydride (NiMH) batteries, which should last the duration of a product’s warranty period under normal use. Please do NOT attempt to change the battery yourself. If the battery has died and you do not want Logitech to replace the battery, you should follow the disposal instructions in the documentation that accompanies your product. Also consult local laws and regulations for the proper disposal of batteries and electronic devices in your region. If there are no local regulations concerning electronic waste disposal, place your product (and its battery) in a waste bin for electronic devices. Caution: Battery Warning! There is a risk of explosion, fire, or chemical burns if a battery is replaced by incorrect type, mutilated, or exposed to conducting materials, liquid, fire, or heat (above 54° C or 130° F). Do not use or recharge a damaged rechargeable battery. Do not use or charge a battery if it appears to be leaking, discolored, deformed, or in any way abnormal. Do not leave a battery discharged or unused for extended periods of time. Do not mix battery types. When a battery is misused, it may explode or leak, causing burns and personal injury. If a battery leaks, use normal precaution and discard it immediately following the local laws and regulations in your area. Power supply warning: Caution electric shock/fire hazard! For indoor use only. Do not expose to moisture, liquid, or heat. Do not use any other power supply with your Logitech product. FCC and IC Statements This Class B digital apparatus complies with Canadian ICES-003. (Cet appareil numérique de catégorie B est conforme à la norme canadienne ICES-003.) This device complies with Industry Canada licence-exempt RSS …

Text truncated - open the document above for the full version.

tt _4F- -g/- t ' oz d mo CVICES 2595 East Bayshore Road, Suite 100 Phone: +1650 5[oi]524 Palo Alto, CA 94303 Fax: +1 650 2-19 2600 March 31,2011 Subject: Attestation of Exclusion of IEEE 802.1 1b Capability To Whom It May Concern, We, Ozmo Devices, hereby attest that our device, OZMO2000, shall never use the IEEE 802.1lb protocol during the normal operation of Logitech's Model Number S-00112. The communication from the host device never uses IEEE 802.1 1b modulations or data rates when communicatins with Logitech's Model Number S-001 12. Furthermore, the user will never be able to force the S-00ll2to connect to an 802.11b network. Firmware for the radio limits operation to data rates of 6 - 24 Mbps for 802.11g and 802.1la. No higher data rates are possible. Please feel free to contact me at (650) 515-3519 or via e-mail at mschwartz(d,ozmodevices.com Sincerely, ' /W*-Q,.a,9 p.r&tru.,*"{- Michael Schwartz Vice President, Engineering Ozmo Devices

Logitech, Inc. 6505 Kaiser Drive, Fremont, CA 94555 USA Tel: (360) 817-1200 ; Fax (360) 817-1331 April 7, 2011 Subject: AttestationofConformity to 47 CFR 15.407(c) To Whom It May Concern, We,Logitech, Inc., hereby attestthat our device,FCC ID:DZLS00112, Model Number S-00112, shalldiscontinue transmission in case of either absence of information to transmit or operational failure in accordance with 47 CFR 15.407(c). The S-00112 device is a client device as defined within 47 CFR 15.202. The S-00112 only transmits acknowledge (ACK) packets to the access point when data is received from the access point to confirm (or not confirm) successful receipt of data from the access point. If no data is transmitted from the access point, no acknowledge packets are transmitted from S-00112. When no data is transmitted from the access point, only control information is transmitted between the access point to S-00112 to maintain a link between the two devices until data is available. If further clarification is needed, please feel free to contact me at (360) 817-1216 or via e-mail at [email protected]. Sincerely, Aaron Cohen Sr. Compliance Engineer Logitech, Inc.

Logitech, Inc. 6505 Kaiser Drive, Fremont, CA 94555 USA Tel: (360) 817-1200 ; Fax (360) 817-1331 April 8, 2011 Federal Communications Commission Authorization and Evaluation Division 7435Oakland Mills Road Columbia, Maryland 21046 Subject:Request forConfidentiality To Whom It May Concern, Request is hereby submitted by Logitech, Inc. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: Schematics Block diagrams Detailed Operational/Functional Description Request is hereby submitted by Logitech, Inc. to withhold from public review for a period of180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. Test setup photos External photos Internal photos User manual Logitech has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Please feel free to contact me at (360) 817-1216 or via e-mail at [email protected]. Sincerely, Aaron Cohen Sr. Compliance Engineer, Logitech Inc.

June 15, 2010 To Whom It M ay Concern, We, the undersigned, hereby authorizeAaron Cohen of Logitech, Inc.to act on our behalf, as our agent, in the following matters related to the FCCand/or Industry Canada app roval of our p roducts: rep ort submittal, related corr esp ondence, the signin g of all documents relatin g to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out byAaron Cohen of Logitech, Inc.within the scop e of this authorization shall havethe same affect as our own. Sincerely , M ark Ohnstad Senior M anager, Product Regulatory Comp liance Logitech, Inc.

Logitech, Inc. 6505 Kaiser Drive, Fremont, CA 94555 USA Tel: (360) 817-1200 ; Fax (360) 817-1331 March 9, 2011 Federal Communications Commission Authorization and Evaluation Division 7435Oakland Mills Road Columbia, Maryland 21046 Subject: Cover Letter To Whom It May Concern, Logitech is requesting an original certification for our unlicensedwirelessadapterproductcalled “Wireless Speaker Adapter for Intel (R) Wireless Music”, Model #S-00112,FCC ID: DZLS00112. The Logitechwirelessadapterproductwill operate under FCCrules 47 CFR 15.247as aDTSdevice and under FCC rules 47 CFR 15.407 as a UNII device.The product uses the IEEE 802.11a/gprotocolas a client device as defined within 47 CFR 15.202. Thewirelessadaptercontains atransceiverthatis a low powerdevicewhich is designed to be placed at least 20cm away from the userto enable a cordless two-way transmission witha source transceiver. Thewirelessadapterdevicewill be utilizing the frequency range of 2400MHz–2483.5MHz (802.11g Channels 1-11 with 1 channel spacing), 5150MHz–5250MHz(802.11a Channels 36- 48 with 2 channel spacing), and 5725MHz-5850MHz(802.11a Channels 149-165 with 4 channel spacing).All bands willemploy aOFDMmodulationscheme.Data rates of 6Mbps, 9Mbps, 12Mbps, 18Mbps, and 24Mbps are possible. The radio hasonedual-band antenna (Ethertronics WLAN 1000146). This configuration satisfies the requirements of 47 CFR 15.203, as shown in later exhibits. If further clarification is needed, please feel freeto contact me at (360)817-1216orvia e-mail at [email protected]. Sincerely, Aaron Cohen Sr.Compliance Engineer Logitech, Inc.

Northwest EMC TCB Compliance Opinion Rev. 12/08/09 LABT0416 Information about the Applicant Grantee (Company Name) Logitech, Inc. FCC Contact Person Mark Ohnstad Address 6505 Kaiser Drive City, State, Zip Fremont, ,CA 94555 Job Number LABT0416 Model S-00112 FCC ID DZLS00112 Agent Aaron Cohen Approval Type Original Equipment Class DTS Digital Transmission System NII Unlicensed National Information Infrastructure Rule Part 15.247 15.407 Overview This application is for a Logitech, Inc. Model S-00112, FCC ID: DZLS00112, which is called Wireless Speaker Adapter for Intel (R) Wireless Music. The device is an 802.11a/g compliant transceiver. The device will not be capable of using the 802.11b frequency bands. Although the device is normally used with at least a 20 cm separation distance between the antenna and all persons, the output power of the device is low enough to meet the requirements of a portable device, without routine RF exposure evaluation. Confidentiality requested for allowed files. Request is properly addressed and referenced. Short term confidentiality requested. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 4/8/2011

Logitech, Inc. 6505 Kaiser Drive, Fremont, CA 94555 USA Tel: (360) 817-1200 ; Fax (360) 817-1331 March 9, 2011 Federal Communications Commission Authorization and Evaluation Division 7435Oakland Mills Road Columbia, Maryland 21046 Subject: FCCID Label and Location To Whom It May Concern, We formally request the following statement, as required by FCC 15.19(a)(3), be allowed to be placed in the user manual for FCC ID DZLS00112: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. It is not practical to place this statement on the unit, as defined in FCC 15.19(a)(5). Please review the user manual to evaluate this substitute method. Please feel free to contact me at (360) 817-1216 or via e-mail at [email protected]. Sincerely, Aaron Cohen Compliance Engineer Logitech, Inc.

Logitech, Inc. 6505 Kaiser Drive, Fremont, CA 94555 USA Tel: (360) 817-1200 ; Fax (360) 817-1331 (10) Antenna Info for DZLS00112 a) Per FCC 15.203, the antenna is internal and permanently attached. It is not intended to be serviced by the customer and is, therefore only serviceable by Logitech, Inc. authorized personnel. (b) See the attached datasheet for more information. ModelEthertronics 1000146 Gain3dBi @ 2.4GHz band 4dBi @ 5GHz band(s) DescriptionDual-band proprietary antenna

Logitech, Inc. 6505 Kaiser Drive, Fremont, CA 94555 USA Tel: (360) 817-1200 ; Fax (360) 817-1331 (11) RF Exposure DZLS00112 Compliance with 47 CFR 15.247(i) “Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter.” The EUT is a transceiver that allows cordless communication of music between a source and the unit. It can be considered amobiletransmitter per 47 CFR 2.1091becausea separationdistance of at least 20 centimeters isnormally maintained between thetransmitter’s radiating structure and the body of the user or nearby persons. The antenna is internal to theunit and permanently attached. The antenna is aproprietary designwith3dBi gain. The maximum peak conducted output power is1.03mW. The maximum peak power is 5.01mW (EIRP) for FCC ID: DZLS00112. The transmit frequency is 2412to 2462MHz, therefore the EUT does not require routine SAR evaluation because it falls below the low power threshold of 60/f(GHz)mW. Please see this excerpt from KDB 447498D01 Mobile Portable RF Exposure v04, item 2)(a)(i): "a device may be used in portable exposure conditions withno restrictions on host platforms when either the source-based time-averaged output power is <=60/f(GHz)mW or all measured 1- g SAR are <0.4 W.kg." The applicant’s wireless radio, FCC ID: DZLS00112, is compliant with the requirements of 15.247(i). Compliance with 47 CFR 15.407(f) (f) U-NII devices are subject to the radio frequency radiation exposure requirements specified in §§ 1.1307(b), 2.1091 and 2.1093 of this chapter, as appropriate. All equipment shall be considered tooperate in a "general population/uncontrolled" environment. Applications for equipment authorization ofdevices operating under this section must contain a statement confirming compliance with theserequirements for both fundamental emissions and unwanted emissions. Technical information showingthe basis for this statement must be submitted to the Commission upon request. The EUT is a transceiver that allows cordless communication of music between a source and the unit. It can be considered a mobile transmitter per 47 CFR 2.1091 becausea separationdistance of at least 20 centimeters isnormally maintained between thetransmitter’s radiating structure and the body of the user or nearby persons. The antenna is internal to the unit and permanently attached. The antenna is a proprietary design with 4dBi gain. The maximum peak conducted output power is5.25mWfor the 5180 to 5240MHz band, and 0.76mW for the 5745 to 5825MHz band. The maximum peak poweris13.19mW (EIRP) for FCC ID: DZLS00112.Wehereby attestthe maximum duty cycleobserved in normal operation is less than 1%. Applyinga source-based duty cycle correction factor to the EIRP,the maximum output power after source-based time averaging is 0.1319mWEIRP. The transmit frequency is 5150 to 5250 MHz, and 5725 to 5850 MHz, therefore the EUT does not require routine SAR evaluation because it falls below the low power threshold of 60/f(GHz)mW. Please see this excerpt from KDB 447498D01 Mobile Portable RF Exposure v04, item 2)(a)(i): "a device may be used in portable exposure conditions with no restrictions on host platforms when either the source-based time-averaged output power is <=60/f(GHz)mW or all measured 1- g SAR are <0.4 W.kg." The applicant’s wireless radio, FCC ID: DZLS00112, is compliant with the requirements of 15.407(f).

Logitech, Inc. S-00112 Report No. LABT0415 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2011 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: March 29, 2011 Logitech, Inc. Model: S-00112 Emissions Test Description Specification Test Method Pass/Fail Occupied Bandwidth FCC 15.247:2011 ANSI C63.10:2009 Pass Output Power – Channel Power FCC 15.247:2011 ANSI C63.10:2009 Pass Band Edge Compliance FCC 15.247:2011 ANSI C63.10:2009 Pass Spurious Conducted Emissions FCC 15.247:2011 ANSI C63.10:2009 Pass Power Spectral Density FCC 15.247:2011 ANSI C63.10:2009 Pass Spurious Radiated Emissions FCC 15.247:2011 ANSI C63.10:2009 Pass AC Powerline Conducted Emissions FCC 15.207:2011 ANSI C63.10:2009 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 9349 W Broadway Ave. Brooklyn Park, MN 55445 Phone: (763) 425-2281 Fax: (763) 424-3469 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834E-1). Approved By: Tim O'Shea, Operations Manager NVLAP Lab Code: 200881-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 06/29/09 Barometric Pressure The recorded barometric pressure has been normalized to sea level. Revision Number Description Date Page Number 00 None Accreditations and Authorizations FCC Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP Northwest EMC, Inc. is accredited under the National Voluntary Laboratory Accreditation Program (NVLAP) for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. NVLAP is administered by the National Institute of Standards and Technology (NIST), an agency of the U.S. Commerce Department. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. Industry Canada Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. (Site Filing Numbers - Hillsboro: 2834D-1, 2834D-2, Sultan: 2834C-1, Irvine: 2834B-1, 2834B-2, Brooklyn Park: 2834E-1) CAB Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. Australia/New Zealand The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). Accreditations and Authorizations VCCI Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (Registration Numbers. - Hillsboro: C-1071, R-1025, G-84, C-2687, T- 1658, and R-2318, Irvine: R-1943, G-85, C-2766, and T-1659, Sultan: R-871, G-83, C-1784, and T-1511, Brooklyn Park: R-3125, G-86, G-141, C-3464, and T-1634). BSMI Northwest EMC has been designated by NIST and validated by C-Taipei (BSMI) as a CAB to conduct tests as described in the APEC Mutual Recognition Agreement (US0017). GOST Northwest EMC, Inc. has been assessed and accredited by the Russian Certification bodies Certinform VNIINMASH, CERTINFO, SAMTES, and Federal CHEC, to perform EMC and Hygienic testing for Information Technology Products. As a result of their laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification KCC Northwest EMC, Inc is a CAB designated by MRA partners and…

Text truncated - open the document above for the full version.

Logitech, Inc. S-00112 Report No. LABT0415.1 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2011 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: March 30, 2011 Logitech, Inc. Model: S-00112 Emissions Test Description Specification Test Method Pass/Fail Emission Bandwidth FCC 15.407:2011 ANSI C63.10:2009 Pass Peak Power Spectral Density FCC 15.407:2011 ANSI C63.10:2009 Pass Peak Excursion of the Modulation Envelope FCC 15.407:2011 ANSI C63.10:2009 Pass Frequency Stability FCC 15.407:2011 ANSI C63.10:2009 Pass Peak Transmit Power FCC 15.407:2011 ANSI C63.10:2009 Pass Spurious Radiated Emissions FCC 15.407:2011 ANSI C63.10:2009 Pass AC Powerline Conducted Emissions FCC 15.207:2011 ANSI C63.10:2009 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 9349 W Broadway Ave. Brooklyn Park, MN 55445 Phone: (763) 425-2281 Fax: (763) 424-3469 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834E-1). Approved By: Tim O'Shea, Operations Manager NVLAP Lab Code: 200881-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 06/29/09 Barometric Pressure The recorded barometric pressure has been normalized to sea level. Revision Number Description Date Page Number 00 None Accreditations and Authorizations FCC Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP Northwest EMC, Inc. is accredited under the National Voluntary Laboratory Accreditation Program (NVLAP) for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. NVLAP is administered by the National Institute of Standards and Technology (NIST), an agency of the U.S. Commerce Department. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. Industry Canada Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. (Site Filing Numbers - Hillsboro: 2834D-1, 2834D-2, Sultan: 2834C-1, Irvine: 2834B-1, 2834B-2, Brooklyn Park: 2834E-1) CAB Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. Australia/New Zealand The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). Accreditations and Authorizations VCCI Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (Registration Numbers. - Hillsboro: C-1071, R-1025, G-84, C-2687, T- 1658, and R-2318, Irvine: R-1943, G-85, C-2766, and T-1659, Sultan: R-871, G-83, C-1784, and T-1511, Brooklyn Park: R-3125, G-86, G-141, C-3464, and T-1634). BSMI Northwest EMC has been designated by NIST and validated by C-Taipei (BSMI) as a CAB to conduct tests as described in the APEC Mutual Recognition Agreement (US0017). GOST Northwest EMC, Inc. has been assessed and accredited by the Russian Certification bodies Certinform…

Text truncated - open the document above for the full version.