F5301NB918WLS918-433NA & PWLS918-433NA

The WLS918 Wireless Panic Pendant is a devicedesigned to transmit an emergency signal from anylocation within the range of the alarm system with whichit is used. Signals from the pendant will be transmittedwhether your alarm system is armed or disarmed.The pendant can be attached to a lanyard or a belt clip.The unit is even small and lightweight enough to beplaced in a shirt pocket or tucked inside a purse. Thependant is also water resistant. Signals will not be transmitted if the pendant is not within the range of the wireless receiver. To activate an alarm , press and hold both large outer buttons for two seconds. If the cap is not replaced, the LED will remain on until the cap is restored. Components of the WLS918The WLS918 is made up of the following components:• Cap - whether it is the tear away cap with attached lanyard (neck strap) or the cap with attached belt clip. • Rubber Boot - this boot adds water resistance to the product and provides a soft grip to be able to easily grab the unit to tear it away orpush the activation buttons • Clear Plastic Housing - the plastic housing holds the circuit board of the WLS918 and is put inside the rubber boot • LED - (Light indication) - the LED is used to indicate various conditions of the pendant and can be seen through the side of the clear plastichousing that is not covered by the rubber boot. • Lithium battery - the WLS918 is powered by a user replaceable lithium battery Assembling the WLS918:Tear Away Assembly:1. The WLS918 comes set up for tear away operation by default. The tear away cap will already be connected to the clear plastic housing. 2. Remove the cover over the bottom of the clear plastic housing3. Put the battery into the pendant (please see ‘Replacing the Battery’ for proper orientation) 4. Insert the clear plastic housing into the rubber boot © 2001 Digital Security Controls Ltd. Printed in Canada 29005932 R001 WLS918-433Wireless Panic PendantOPERATING INSTRUCTIONS FCC COMPLIANCE STATEMENTCAUTION : Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: n Re-orient the receiving antenna. n Increase the separation between the equipment and receiver. n Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. n Consult the dealer or an experienced radio/television technician for help. The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/ Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Wash-ington D.C. 20402, Stock # 004-000-00345-4.Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device.Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisationest autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateurdu dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptiblede compromettre le fonctionnement du dispositif.LIMITED WARRANTY Digital Security Controls Ltd. warrants that for a period of twelve months from the date ofpurchase, the product shall be free of defect in materials and workmanship under normal useand that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at itsoption, repair or replace the defective equipment upon return of the equipment to its repairdepot. This warranty applies only to defects in parts and workmanship and not to damageincurred in shipping or handling, or damage due to causes beyond the control of DigitalSecurity Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage,or damage arising out of abuse, alteration or improper application of the equipment.The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of anyand all other warranties, whether expressed or implied and of all other obligations or liabilitieson the part of Digital Security Controls Ltd. This warranty contains the entire warranty. DigitalSecurity Controls Ltd. neither assumes responsibility for, nor authorizes any other personpurporting to act on its behalf to modify or to change this warranty, nor to assume for it anyother warranty or liability concerning this product.In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequentialdamages, loss of anticipated profits, loss of time or any other losses incurred by the buyer inconnection with the purchase, installation or operation or failure of this product.WARNING: Digital Security Controls Ltd. recommends that the entire system be com-pletely tested on a regular basis. However, despite frequent testing, and due to, but notlimited to, criminal tampering or electrical disruption, it is possible for this product to failto perform …

Text truncated - open the document above for the full version.

September 11, 2001 Office of Engineering & Technology Federal Communications Commission Washington, D.C. 20554 Subject:Request for continuous confidentiality of technical information per sections 0.459 and 0.457 (d) (2) ( I) of CFR 47. FCC ID:F5301NB918 Dear Sir or Madam: Digital Security Controls Canada Ltd. is hereby filing this request for continuous confidentiality of the specified items submitted with the application for certification ( Form731 ) with proposed identifier F5301NB918. The technical documentation for which continuous confidentiality is sought is: (1) Schematic diagrams, PCB Layers (2) Parts List (3) Operational Description (4) Block Diagram This technical documentation is a part of the material supporting the Form 731 application for certification, which this request for confidentiality accompanies. The schematic diagrams disclose proprietary information and technical data which Digital Security Controls Ltd. would guard from its competitors and would not make available to the public. This proprietary information constitutes a trade secret and is not a part of the product documentation that would be made available to the customers of Digital Security Controls Ltd. It would be potentially injurious to Digital Security Controls Ltd. and to its investment in the development of this innovative proprietary product to make available for public disclosure the trade secret technical information specified in this request. If there are any questions about this request for continuous confidentiality regarding trade secrets and proprietary information embodied in the technical documentation filed in support of this Form 731 application, then please contact me via our toll-free telephone number. Yours truly, Kevin Harris Approval Services Manager 905-760-3000 Ext. 2378 Email: [email protected]

T H E A R T O F S E C U R I T Y September 10, 2001 Ref.: Industry Canada Registration of the model PWLS918-433 To Whom It May Concern: The radio applications between the WLS918-433 and PWLS918-433 are identical. The only difference between the two models being marketing literature. Yours tr ul y, Kevin Harris Approvals Services Manager Email: [email protected] Tel: 1-888-888-7838 Ext. 2378

PWLS918-433 WIRELESS PANIC PENDANT FCC/IC LABELING File: [pwls918-433_fcc+ices_lb_18011111_r001.cdr] August 2, 2001 Front of the unit showing placement of label (actual size) ! ! ! Dashed line indicates cut edge of label Label to be printed on self-adhesive material Label shown 250% of actual size 35 mm 12.7 mm Digital Security Controls Ltd. ISO9001 Registered 3301 Langstaff Road, Concord Ontario, Canada L4K 4L2 Phone: 905-760-3000 Toll Free: 1-888-888-7838 Fax: 905-760-3030 ® PWLS918-433 Digital Security Controls Ltd. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: F5301NB918 IC: RSS/CNR210 CANADA 160 XXX XXXX MADE IN CANADA18011111 R001 This Class B digital apparatus meets all requirements of the ICES-003. Cet appareil numérique de la classe B respecte toutes les exigences du ICES-003. PWLS918-433 Digital Security Controls Ltd. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: F5301NB918 IC: RSS/CNR210 CANADA 160 XXX XXXX MADE IN CANADA18011111 R001 This Class B digital apparatus meets all requirements of the ICES-003. Cet appareil numérique de la classe B respecte toutes les exigences du ICES-003.

WLS918-433 Digital Security Controls Ltd. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: F5301NB918 IC: RSS/CNR210 CANADA 160 XXX XXXX MADE IN CANADA18011110 R001 This Class B digital apparatus meets all requirements of the ICES-003. Cet appareil numérique de la classe B respecte toutes les exigences du ICES-003. WLS918-433 WIRELESS PANIC PENDANT FCC/IC LABELING File: [wls918-433_fcc+ices_lb_18011110_r001.cdr] August 2, 2001 Front of the unit showing placement of label (actual size) ! ! ! Dashed line indicates cut edge of label Label to be printed on self-adhesive material Label shown 250% of actual size 35 mm 12.7 mm Digital Security Controls Ltd. ISO9001 Registered 3301 Langstaff Road, Concord Ontario, Canada L4K 4L2 Phone: 905-760-3000 Toll Free: 1-888-888-7838 Fax: 905-760-3030 ® WLS918-433 Digital Security Controls Ltd. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: F5301NB918 IC: RSS/CNR210 CANADA 160 XXX XXXX MADE IN CANADA18011110 R001 This Class B digital apparatus meets all requirements of the ICES-003. Cet appareil numérique de la classe B respecte toutes les exigences du ICES-003.

Master:PT15231 Date: February 25, 2001 Test Report:1W04030 Applicant:Digital Security Controls Ltd. 3301 Langstaff Road Vaughan, Ontario L4K 4L2 Equipment Under Test:UA 206 WLS 918 (EUT)433MHz Product In Accordance With:FCC Part 15, Subpart C For Low Power Transmitters Operating Periodically In The Band 40.66 - 40.77 MHz And Above 70 MHz Tested By:Nemko Canada Inc. 3325 River Road, R.R. 5 Ottawa, Ontario K1V 1H2 Authorized By: R. Grant, Wireless Group Manager Date: Total Number of Pages:21 Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 2 of 21 Table of Contents Section 1. Summary of Test Results.......................................................................................... 3 Section 2. Equipment Under Test (EUT) ................................................................................. 5 Section 3. Transmission Requirements .................................................................................. 11 Section 4. Radiated Emissions................................................................................................. 14 Section 5. Occupied Bandwidth.............................................................................................. 17 Section 6. Block Diagrams.......................................................................................................19 Section 7. Test Equipment List ............................................................................................... 21 Annex A Restricted Bands.................................................................................................... A1 Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 3 of 21 Section 1.Summary of Test Results General All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C, Paragraph 15.231. All tests were conducted using measurement procedure ANSI C63.4-1992. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. New SubmissionProduction Unit Class II Permissive ChangePre-Production Unit DS C Equipment Code THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. NVLAP LAB CODE: 100351-0 TESTED BY: ___________________________ DATE: ___________________ Wayne Clarke, Wireless Technologist Nemko Canada Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 4 of 21 Summary Of Test Data Name of TestPara. NumberResults Transmission Requirements15.231(a)Complies Radiated Emissions15.231(b)Complies Occupied Bandwidth15.231(c)Complies Frequency Tolerance15.231(d)N/A Periodic Alternate Field Strength Requirements15.231(e)N/A Powerline Conducted Emissions15.207N/A Footnotes For N/A’s:The EUT is battery operated 433MHz Emergency Pendant Transmitter Test Conditions: IndoorTemperature: 23 °C Humidity:50 % OutdoorTemperature: 26 °C Humidity:78 % Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 5 of 21 Section 2.Equipment Under Test (EUT) General Equipment Information Manufacturer:Digital Security Controls Ltd. Model No.:UA 206 WLS 918 Serial No.:None Date Received In Laboratory:June 14, 2001 Nemko Identification No.:Item #2 Frequency Range:433 MHz Operating Frequency(ies) of Sample:433.92 MHz Type of Emission:L1D Emission Designator:35K0L1D Supply Power Requirement:3V Lithium Battery CR 3032 Duty Cycle Calculation:20 log 12.25ms 100 ms -18.2dB as declared by the manufacturer. Graphs confirm declaration. Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 6 of 21 Wide Pulse On Time Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 7 of 21 Narrow Pulse On Time Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 8 of 21 On Time In 100ms Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 9 of 21 Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 10 of 21 Nemko Canada Inc. FCC PART 15, SUBPART C FOR LOW POWER TRANSMITTERS PROJECT NO.: 1R04030 EQUIPMENT: UA 206 WLS 918, 433MHz Product Page 11 of 21 Section 3.Transmission Requirements Para. No.: 15.231(a) Test Performed By: Wayne ClarkeDate of Test: June 15, 2001 Minimum Standard:15.231(a) Continuous transmissions such as voice, video or data transmissions are not permitted. 15.231(a)(1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds after being released. 15.231(a)(2) A transmitter activated automatically shall cease transmission within 5 seconds of activation. 15.231(a)(3) Periodic transmissions at regular pre-determined intervals are not permitted. However polling or superviso…

Text truncated - open the document above for the full version.