F5323MC312NDoor/Window Outdoor Contact

MC-312N NBIoT Outdoor wireless magnetic contact with auxiliary input Installation Guide Overview of the MC-312N NBIoT The reference to MC-312N NBIoT throughout this manual includes the model MC-312N NBIoT. Figure 1: MC-312N NBIoT 1 2 Table 1: Device overview CalloutComponent 1Device 2Magnet The MC-312 NBIoT is a wireless outdoor magnetic contact with an auxiliary input. This outdoor contact is an internet of things (IoT) device and works in narrowband (NB) IoT networks while connecting with data and device management (DM) servers. The MC-312N NBIoT has a range of features, which include: • Flat and curved surface installation • Weatherproof and water-resistant IP66 outdoor transceiver • Separate transmissions from sensor and auxiliary input that trigger the same cellular transmitter • Battery life of up to 2 years with typical use • Integrated magnetic sensor • Anti-masking detection • Auxiliary hardwired input, programmable as either normally open, normally closed, end of line or double end of line for use with an additional device • Front and back tamper detection • Paintable using non-metallic paint. Suggested paints include: DUPLI-COLOR Vinyl & Fabric Coating, RUST-OLEUM Plastic, KRYLON Fusion for Plastic • Temperature level reports • Bluetooth low energy (BLE) interface supporting the Installer and User Apps for local settings • Over the air (OTA) and firmware over the air (FOTA) upgrade capability D-308914 *D-308924* D-308914 MC-312N NBIoT Rev. 0 • Power Save Mode (PSM) Getting Started Inserting the Micro SIM card Important: - In order to match the temperature range of the device, use an industrial grade IoT/ M2M Micro SIM card. For more information, see Specifications. - The Micro SIM card tray is located behind the batteries in the device. Before inserting the Micro SIM card you must remove the batteries. For more information, see Inserting or replacing the batteries 1. Slide up the metal cover to the OPEN position. 2. Open the cover. 3. Place the Micro SIM card in the tray with the chip face down. 4. Close the metal cover. 5. Slide the cover back to the LOCK position. Figure 2: Inserting the Micro SIM card Inserting or replacing the batteries WARNING: - There is a risk of explosion if you replace the batteries with an incorrect type. - Dispose of used batteries according to the battery manufacturer's instructions and according to local rules and regulations. 1. Insert a flat-head screwdriver into the slots provided and push upward to remove the decorative cover. See Figure 6 2. Unscrew the battery cover screw, then remove the battery cover. See Figure 3. MC-312N NBIoT Outdoor wireless magnetic contact with auxiliary input Installation Guide2 D-308914 MC-312N NBIoT Rev. 0 Figure 3: Removing the battery cover 3. To replace the batteries, remove the old batteries and wait one minute. 4. Insert the new batteries with the + and - symbols matching the illustration in the battery compartment. 5. Replace the battery cover and close the screw. Reattach the decorative cover. See Figure 4 . Figure 4: Replacing the battery cover Enrolling the NBIoT device Note: Before enrolling the device you should perform a link quality test. For more information, see Performing a link quality test For the device to operate as expected you must enroll or register the device at the device manager (DM) server. To do so, complete the following steps: 1. Insert the SIM card into the device. For more information, see Figure 2 2. Insert the batteries. For more information, see Inserting or replacing the batteries 3. Leave the battery cover open. 4. Follow the instruction on the application to enroll and register the device. Note: You can find your 15 digit IMEI number and PIN code printed on the box of the device when prompted by the application. 3MC-312N NBIoT Outdoor wireless magnetic contact with auxiliary input Installation Guide D-308914 MC-312N NBIoT Rev. 0 Installation guidelines • Only qualified service personnel can install the device. • Place the device above the door or window on the fixed frame. Place the magnet on the movable part of the door or window. Do not place the magnet more than 44.5 mm or 1.75 in. from the marked side of the device. • Mount the magnet either parallel or perpendicular to the device. For more information, see Figure 12 or Figure 13 • For devices with a back tamper, ensure the device is seated firmly within the bracket at all times and that the break-away bracket segment is fastened securely to the mounting surface. For more information, see callout 2 and callout 3 in Figure 7. For more information about tamper detection, see Tamper detection Figure 5: Device interior CalloutDescription 1Front tamper switch 2Sim card holder 3Anti-masking calibration button Mounting the NBIoT device on a flat or curved surface 1. Note: Align the device and magnet according to the specifications in Range coverage directions. To remove the decorative cover, insert a flat-head screwdriver into the slot provided and push upward. See Figure 6 MC-312N NBIoT Outdoor wireless magnetic contact with auxiliary input Installation Guide4 D-308914 MC-312N NBIoT Rev. 0 Figure 6: Removing decorative cover 2. Unscrew the lower screw from the device cover and separate the device from the bracket. See Figure 7 Figure 7: Seperating the device 3. Mark, drill, and screw the required amount of holes in the mounting surface with one of the following options: - For tamper protection, use both middle holes. See Figure 8 and callout 2 and callout 3 in Figure 7. - For a standard mount, use the uppermost and lowermost hole in the device bracket only. See Figure 8 and callouts 1 and 4 in Figure 7. - To mount the device impermanently on a curved surface, insert the straps through the slots in the device and magnet brackets. Fasten both straps to the curved surfaces. See Figure 9 Note: Straps are not included with the product. 5MC-312N NBIoT Outdoor wireless magnetic contact with auxiliary input Installation Guide D-308914 M…

Text truncated - open the document above for the full version.

Tyco Safety Products Canada Ltd. 3301 Langstaff Road Concord, Ontario, Canada L4K 4L2 Tele: 1-647-480-0200 https://www.tycosafetyproducts.com Certification Application Attestation Statements Tyco Safety Products Canada Ltd. 3301 Langstaff Road L4K 4L2 Ontario, Canada To Whom It May Concern: FCC ID: F5323MC312N Statement for 47 CFR section 2.911(d)(5)(i) Tyco Safety Products Canada Ltd. certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) Tyco Safety Products Canada Ltd. (“the applicant”) certifies that, as of the date of the filing of this application, the applicant - is / - is not (3) identified on the Covered List as an entity producing “covered” equipment. Date: 12-Feb.-23 City: Concord Name (2) : Dan Nita Function: Approvals Manager Telephone number: 1-647-480-0430 Email address: [email protected] Signature: 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . (2): For FCC it must be the Grantee Code “owner” or the authorized agent. (3): double click on the appropriate box and select ‘’checked” then “OK”

Tyco Safety Products Canada Ltd. 3301 Langstaff Road Concord, Ontario, Canada L4K 4L2 Tele: 1- 647-480-0200 https://www.tycosafetyproducts.com U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Kiwa Nederland B.V. Wilmersdorf 50 7327 AC Apeldoorn Postbus 137 7300 AC Apeldoorn Netherlands ATTEN TION: FCC Certification – Section 2.911(d)(7) Information Desi gnated U.S. Agent Company name: Qolsys Inc. FRN: 0022572226 Contact person name: Mark Skeen Street address: 1919 S. Bascom Ave. ZIP/City/State Campbell, CA 95008, USA Telephone number: Email address: [email protected] Signature: Date: 20230316 This l etter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. The App licant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applic ant Company name: Tyco Safety Products Canada Ltd. Grantee Code: F53 Contact person name: Dan Nita Street address: 3301 Langstaff Road ZIP/City/State LK4 4L2, Concord, Ontario, Canada Telephone number: Email address: [email protected] Signature: Date: 20.3.2023 +1 (855) 476-5797 +1 (647) 8000430 Revision Record Sheet: Revision Section number Page number Date Remark(s) issued by 01 07-02-2023 1 st version RvdM 02 1 15-05-2023 Added FRN to Agent details RvdM Issued/modified by : Richard van der Meer Function : Certification assessor Revision : 02 Date : 15-02-2023 Verified by : Willem Jan Jong Function : Team Lead Date : __-02-2023 Released by : Axel Gase Function : Manager Quality Assurance Date of release: : __-02-2023

March 23, 2023 Telefication B.V. Attn: Dept. FCC TCB Wilmersdorf 50 7327 AC Apeldoorn The Netherlands Subject: Application for certification for a Door/Window Outdoor Contact, FCC ID: F5323MC312N Dear Gentlemen, Please find attached our application for certification for a Door/Window Outdoor Contact, FCC ID: F5323MC312N, prepared in accordance with FCC Rules, parts 2 and 15, section 15.247(DTS). The product testing and this application for certification were performed by Hermon Laboratories, which is recognized and accredited by FCC, Test Firm Registration Number i s 927748, Designation Number is IL1001. Hermon Labs responsible person is Mr. Michael Nikishin, tel: +972 4626 8440, fax:+972 4628 8277, e-mail: [email protected]. We hope this application satisfies your requirements. Please send an invoice to Hermon Labs. Dan Nita, Approvals Manager Tyco Safety Products Canada Ltd.

Tyco Safety Products Canada Ltd. 3301 Langstaff Road Concord, Ontario, Canada L4K 4L2 Tele: 1-647-480-0200 https://www.tycosafetyproducts.com Declaration of Authorization We Name: Tyco Safety Products Canada Ltd. Address: 3301 Langstaff Road City: Concord L4K 4L2 Country: Ontario, Canada Declare that: Name Representative of agent: ....................... (1) Agent Company name: Hermon Laboratories Ltd. Address: Harakevet Industrial Zone City: Binyamina 30500 Country Israel is authorized to apply for Certification of the following product(s): Product description: Door/Window Outdoor Contact Type designation: MC-312NNBIOT Trademark: Johnson Controls Validity/ expiry date: January 11, 2024 on our behalf. Date: January 12, 2023 Name: Dan Nita (2) Function: Approvals Manager Signature: Notes: (1) : Required for FCC application (2) : For FCC it must be the Grantee Code “owner” or the authorized agent

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Company Name: Tyco Safety Products Canada Ltd. Address: 3301 Langstaff Road City: Concord L4K 4L2 Country: Ontario, Conada To: Telefication B.V., Dept. FCC TCB Wilmersdorf 50 7327 AC Apeldoorn The Netherlands Subject: Request for confidentiality FCC ID: F5323MC312N Reference number: 47336 Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: in order to avoid exposed of the technology to the competitors Date: March 23, 2023 Name and signature of applicant: Mr. Dan Nita Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 1 of 5 EXTERNAL PHOTOGRAPHS This document contains 2 photographs Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 2 of 5 Photograph No.1 Door/Window Outdoor Contact Front view Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 3 of 5 Photograph No.2 Door/Window Outdoor Contact Botton view Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 4 of 5 Photograph No.3 Door/Window Outdoor Contact Rear side view Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 5 of 5 Photograph No.4 Door/Window Outdoor Contact Rear side view

Change Title: JCI LABEL DRAWING New FCC ID/IC Product Name: LABEL NBIOT MC-312N PRODUCT Date Name Update Picture Document No: 4017747 17.01.2023 Albert F. Created Document Rev: Draft02 29.03.2023 Albert F. Updated Sheet 1 of 1 29.03.2023 Shay A. Approved MATERIAL: PVR S -303665 SIZE: Label Polyester 14*40mm

Tyco Safety Products Canada Ltd. FCC ID: F5323MC312N IC: 160A- MC312N Page 1 of 4 INTERNAL PHOTOGRAPHS This document contains 6 photographs Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 2 of 4 Photograph No.1 Door/Window Outdoor Contact Internal view Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 3 of 4 Photograph No.2 Door/Window Outdoor Contact Print side of the main PCB Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A- MC312NNBIoT Page 4 of 4 Photograph No.3 Door/Window Outdoor Contact Antenna assembly

FCC ID: F5323MC312N Page 1 of 2 Environmental evaluation and exposure limit according to FCC CFR 47part 1, §1.1307, §1.1310 The Home unit is classified as a mobile device. The Home unit includes transmitter operating according to FCC part 15 subpart C section 15.247 (DTS) and Cellular module approval under FCC ID: RI7ME310G1W1. BLE and the Cellular work together only at the installation stage. Limit for power density for general population/uncontrolled exposure is 1mW/cm 2 for 1500 -100000 MHz frequency range. The power density P (mW/cm 2 ) = P T / 4 r 2 , where PT is the transmitted power, which is equal to the peak transmitter output power 3.34 dBm plus maximum antenna gain (-13)dBi, the maximum equivalent isotropically radiated power EIRP is PT = 3.34dBm + (-13)dBi = -9.66dBm = 0.108mW 3.34 dBm is the EUT maximum output power with the tune up tolerance, -13 dBi – antenna gain. The power density at 20 cm (minimum safe distance, required for mobile devices), calculated as follows: 0.108mW / 4 (20 cm) 2 = 0.0002mW/cm 2 << 1mW/cm 2 Maximum conducted power given in FCC ID: RI7ME310G1W1 module grant is 158mW (21.99dBm) in band 2, 153mW (21.85dBm) in band 4, 138mW (21.4dBm) in band 5, 157mw (21.96dBm) in band 12, 138mW (21.4dBm) in band 13, 147mW (21.67dBm) in band 25, 145mW (21.61dBm) in band 26, 158mW (21.99dBm) in band 66, 142mW (21.52dBm) in band 71 and 129mW (21.11dBm) in band. Limit for power density is f/1500= 0.56mW/cm2 for band 5 (824-849 MHz), 0.47mW/cm2 for band 12 (699-716 MHz), 0.52mW/cm2 for band 13 (777-787 MHz), 0.56mW/cm2 for band 26 (814-849 MHz), 0.46mW/cm2 for band 71 (663-698 MHz), 0.47mW/cm2 for band 85 (698-716 MHz) and 1mW/cm2 for 1500 -100000 MHz for general population/uncontrolled exposure for bands 25, 4, 66 and 2. The gain of antennas used with the module are 11dBi for band 2 and band 25, 8dBi for band 4 and band 66, 12.4dBi for band 5, 11.6dBi for band 12, 12.1dBi for band 13, 12.3dBi for band 26, 11.6dBi for band 85 and 11.4dBi for band 71. The maximum equivalent isotropic radiated power EIRP is for band 26: PT = 21.61dBm + 12.3dBi = 33.91 dBm = 2460.36mW The power density at 20 cm (minimum safe distance, required for mobile devices), calculated as follows: 2460.36mW / 4 (20 cm) 2 = 0.489mW/cm 2 << 0.56mW/cm 2 FCC ID: F5323MC312NNBIoT Page 2 of 2 Assessment of RF hazard from BLE and LTE wireless module S1/limit + S2/limit ≤ 1, i.e 0.0002/1 + 0.489/0.56 = 0.0002 + 0.8732 = 0.8734 ≤ 1 The aggregate ratio of transmit power to the relevant power limits does not exceed 100% and meets the safety requirements.

Hermon Laboratories Ltd. P.O. Box 23, Binyamina 3055001, Israel Tel. +972 4628 8001 Fax. +972 4628 8277 E-mail: [email protected] Page 1 of 56 Report ID: TYCRAD_FCC.47336_Rev1.docx Date of Issue: 23-Mar-23 ELECTRICAL TESTING 0839.01 TEST REPORT ACCORDING TO: FCC 47CFR part 15 subpart C §15.247 (DTS) and subpart B, RSS-247 Issue 2:2017, RSS-Gen Issue 5, ICES-003 Issue 7:2020 FOR: Tyco Safety Products Canada Ltd. Door/Window Outdoor Contact Model: MC-312N NBIOT FCC ID: F5323MC312N IC: 160A- MC312N This report is in conformity with ISO/ IEC 17025. The "A2LA Accredited" symbol endorsement applies only to the tests and calibrations that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: TYCRAD_FCC.47336_Rev1.docx Date of Issue: 23-Mar-23 Page 2 of 56 Table of contents 1 Applicant information ..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details .................................................................................................................................................................... 3 5 Tests summary .............................................................................................................................................................. 4 6 EUT description ............................................................................................................................................................. 5 6.1 General information ....................................................................................................................................................... 5 6.2 Test configuration .......................................................................................................................................................... 5 6.3 Changes made in EUT .................................................................................................................................................. 5 6.4 Transmitter characteristics ............................................................................................................................................ 6 7 Transmitter tests according to 47CFR part 15 subpart C and RSS-247 requirements .................................................. 7 7.1 Minimum 6 dB and 99% bandwidth ............................................................................................................................... 7 7.2 Field strength of spurious emissions ........................................................................................................................... 12 7.3 Peak output power ...................................................................................................................................................... 31 7.4 Band edge radiated emissions .................................................................................................................................... 36 7.5 Peak spectral power density ....................................................................................................................................... 42 7.6 Antenna requirements ................................................................................................................................................. 46 8 Unintentional emissions .............................................................................................................................................. 47 8.1 Radiated emission measurements .............................................................................................................................. 47 9 APPENDIX A Test equipment and ancillaries used for tests ....................................................................................... 50 10 APPENDIX B Test equipment correction factors ......................................................................................................... 51 11 APPENDIX C Measurement uncertainties .................................................................................................................. 53 12 APPENDIX D Test laboratory description ................................................................................................................... 54 13 APPENDIX E Specification references........................................................................................................................ 55 14 APPENDIX F Abbreviations and acronyms ................................................................................................................. 56 Report ID: TYCRAD_FCC.47336_Rev1.docx Date of Issue: 23-Mar-23 Page 3 of 56 1 Applicant information Client name: Tyco Safety Products Canada Ltd. Address: 3301 Langstaff Road, Concord, Ontario L4K 4L2, Canada Telephone: 1-647-480-0430 Fax: 1-647-480-0531 E-mail: [email protected] Contact name: Mr. Dan Nita 2 Equipment under test attributes Product name: Door/Window Outdoor Contact Product type: Transceiver Model(s): MC-312N NBIOT Serial number: NA Hardware version: 90-210072 Software release: JS-704032 Receipt date 02-Jun-22 3 Manufacturer information Manufacturer name: Tyco Safety Products Canada Ltd. Address: 3301 Langstaff Road, Concord, Ontario L4K 4L2, Canada Telephone: 1-647-480-0430 Fax: 1-647-480-0531 E-Mail: [email protected] Contact name: Mr. Dan Nita 4 Test details Project ID: 47336 Location: Hermon Laborat…

Text truncated - open the document above for the full version.

Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A-MC312NNBIoT Page 1 of 6 SETUP PHOTOGRAPHS This document contains 5 photographs Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A-MC312NNBIoT Page 2 of 6 Photograph No.1 Setup for spurious field strength measurements in anechoic chamber from 9 kHz to 30 MHz Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A-MC312NNBIoT Page 3 of 6 Photograph No.2 Setup for carrier and spurious emissions measurements in anechoic chamber from 30 MHz to 1 GHz Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A-MC312NNBIoT Page 4 of 6 Photograph No.3 Setup for field strength measurements in anechoic chamber above 1 GHz Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A-MC312NNBIoT Page 5 of 6 Photograph No.4 Setup for carrier field strength measurements, EUT cabling Tyco Safety Products Canada Ltd. FCC ID: F5323MC312NNBIoT IC: 160A-MC312NNBIoT Page 6 of 6 Photograph No.5 Setup for 20 dB bandwidth measurements