I4U27VT2-L5-E1P5Microwave Transmitter

NEWSCASTER VT2 ENG/OB Microwave Transmitter User Manual M17-0002-00A (rev 1.0) (software version D3.xx) Nucomm Inc. 101 Bilby Road Hackettstown, NJ 07840 Tel: 908-852-3700 Fax: 908-813-0399 www.nucomm.com NewsCaster VT2 M17-0002-00A Rev 4 2 User Manual Warranty Equipment manufactured by Nucomm, Inc. is warranted to meet all customer specifications and to be free from defects in material and workmanship within a period of two years from date of shipment from Nucomm. The company’s liability under this warranty is limited to: • Servicing or adjusting equipment. • Replacement of defective parts. Any equipment returned to the factory shall have the freight paid for by the buyer. Equipment showing damage by misuse, abnormal conditions of operation, or attempts to repair by other than authorized service personal shall be excluded from this warranty. Nucomm, Inc. shall in no event be responsible for incidental injury or property damage. Since Nucomm, Inc. has no control over conditions of use, no warranty is made or implied as to suitability for the customer’s intended use, beyond such performance specifications as are made part of the purchase order. There are no warranties expressed or implied, except as stated herein. This limitation on warranties shall not be modified by verbal representations. Proprietary & Disclaimer Notice All information and graphic images herein contained within this manual are considered the sole property of Nucomm, Inc. and is issued in the strictest of confidence. This material may not be reproduced, stored, copied, or converted in any form, nor shall it be disclosed to others or used for manufacturing or any other purpose without the written permission of an authorized representative of Nucomm, Inc. Nucomm, Inc. has made every effort to ensure the accuracy of this material at the time of printing. However, as the specifications, equipment, and this manual are subject to change without notice, Nucomm, Inc. assumes no responsibility or liability whatsoever for any errors or inaccuracies that may appear in this manual, or for any decisions based on its use. This manual is supplied for informational purposes only and should not be construed as a commitment by Nucomm, Inc. © Copyrighted 2005, Nucomm, Inc., Hackettstown, New Jersey 08740 NewsCaster VT2 M17-0002-00A Rev 4 3 User Manual Customer Service Information Equipment Returns Customer Service technicians at Nucomm are available to extend technical assistance to customers installing or operating Nucomm equipment. They will also assist customers with equipment troubleshooting. If this cannot be successfully accomplished by telephone, the equipment may be returned to the factory for repair. Loaner equipment is often available until Nucomm is able to ship repaired units. The Nucomm Customer Service telephone number is (908) 852-3700. Do not return any Nucomm product to the factory until you have received a return authorization (RA) number and shipping instructions from Nucomm. When returning equipment to Nucomm, please enclose a letter containing the following: • RA number. • Model number. • Serial number. • Frequency operating range (in the case of modules). • A detailed description of the problem. • Name of an engineer or technician we may contact in regards to this problem. • Include a “ship to” and “bill to” address. Ship to: Nucomm, Inc. 101 Bilby Road Hackettstown, New Jersey 07840 For International orders In the case of units being shipped from outside the United States, Nucomm recommends the use of a courier such as Federal Express, UPS, etc, and that the goods be shipped DOOR-TO-DOOR PRE-PAID. This will eliminate Customs costs, handling charges and delays. Enclose all the information above, plus a statement that the equipment was manufactured in the United States (the latter is needed to expedite customs processing). Nucomm evaluates all returned units free of charge, and then confers with customers on corrective action. Telephone Consultation Should there be a need for emergency telephone consultation, please have your model number and serial number available for the Customer Service representative. Nucomm Customer Service representatives are available to deal with all technical questions or difficulties. NewsCaster VT2 M17-0002-00A Rev 4 4 User Manual Replacement Modules Troubleshooting to the component level is often not cost-effective and frequently impossible. Often the practical method of effecting field repairs is to substitute known good spare modules for suspect units. Nucomm maintains an inventory of replacement modules for its complete line of products. Field Repair Nucomm products are designed with easy access to components to facilitate service. When troubleshooting the VT2 Transmitter, the user is cautioned to read all module descriptions in this manual. Some Nucomm modules cannot be serviced in the field. Warnings are included in the circuit descriptions and on certain modules themselves, however the lack of a warning cannot be construed as a statement of safety. To prevent voiding of the Nucomm warranty that protects the equipment, please contact Nucomm before servicing or making any repairs. Shipping Damage Equipment shipped FOB Nucomm, Inc.; shall become the property of buyer upon delivery to and receipt from carrier. Any damage in shipment should be handled by the buyer directly with the carrier. Immediately request the carrier’s inspection upon evidence of damage in shipment. Do not return any Nucomm product to the factory until a return authorization (RA) number has been given, along with shipping instructions, as discussed previously. Contact Information Nucomm Inc. 101 Bilby Road Hackettstown, NJ 07840 Tel: 908-852-3700 Fax: 908-813-0399 www.Nucomm.com For 24-hour emergency service, our Customer Service Manager can be contacted by pager at (908) 515-3709. NewsCaster VT2 M17-0002-00A Rev 4 5 User Manual CAUTION! RISK OF ELECTRICAL SHOCK. DO NOT REMOVE COVERS. • Do not remove any covers. • R…

Text truncated - open the document above for the full version.

101 Bilby Road, Hackettstown, N.J. 07840 Phone: 908-852-3700 FAX: 908-813-0399 Date: 4/10/07 To Whom It May Concern: Nucomm, Inc. in support of the FCC Broadcast Auxiliary Services Relocation (BAS) plan are building radios which will be moving off of the existing (Incumbent) frequency channel plan identified in Table 1: Power Output: 1990-2500 MHz (Incumbent Frequencies) onto a new channel frequency and band width plan identified in a Table 2: Power Output: 2031.5-2500 MHz (BAS New Frequencies). The channel and frequencies identified in all three tables are being exclusively used in support of electronic news gathering. Table 1: Power Output: 1990-2500 MHz (Incumbent Frequencies) Analog Mode (Watts) Digital Mode (Watts) Channel Frequency (MHz) High Low High Low 1 1999.0 12.30 2.95 4.90 1.20 4 2050.5 12.59 3.02 5.01 1.23 7 2101.5 12.88 3.09 5.13 1.26 9 2475.5 11.48 2.75 4.47 1.12 10 2492.5 10.96 2.69 4.37 1.10 Table 2: Power Output: 2031.5-2500 MHz (BAS New Frequencies) Analog Mode (Watts) Digital Mode (Watts) Channel Frequency (MHz) High Low High Low 1 2031.5 12.59 3.09 5.01 1.26 3 2055.5 12.88 3.09 5.13 1.26 101 Bilby Road, Hackettstown, N.J. 07840 Phone: 908-852-3700 FAX: 908-813-0399 Analog Mode (Watts) Digital Mode (Watts) Channel Frequency (MHz) High Low High Low 5 2079.5 12.88 3.16 5.13 1.29 7 2103.5 12.88 3.16 5.25 1.32 10 2492.5 11.22 2.69 4.57 1.12 Table 3 Power Output: 6425-7125 MHz (BAS New Frequencies) Analog Mode (Watts) Digital Mode (Watts) Channel Frequency (MHz) High Low High Low 1 6887.5 5.62 1.32 1.41 0.46 4 6962.5 5.50 1.32 1.38 0.45 7 7037.5 5.50 1.32 1.38 0.45 10 7112.5 5.50 1.29 1.38 0.44 14 6512.5 6.31 1.51 1.66 0.51 Sincerely, ____________________________ George Williamson Project Management, Nucomm, Inc.

101 Bilby Rd Hackettstown, NJ 07840 USA (908) 852-3700 www.nucomm.com Date: 4/2/07 Page 1 of 1 Confidentiality Request Pertaining to Request for Certification of FCC ID: I4U27VT2-L5-E1P5 Nucomm hereby respectfully requests confidentiality of certain materials pursuant to published FCC guidelines, with respect to our Request for Certification of FCC ID: I4U27VT2-L5-E1P5, in accordance with FCC Sections 0.459(b), and 0.457(d) Nucomm has submitted a Technical Report, as required by FCC guidelines, in conjunction with the Request for Certification. Certain parts of this Technical Report and/or the attendant submittals contain information that are trade secrets and are requested to be withheld from public inspection. The attachments and/or exhibits, henceforth collectively “Materials”, designated as (a) Schematics, including descriptions of circuitry, (b) Parts Lists, (c) Block Diagrams, (d) Operational descriptions and (e) All internal photographs and Trace Layouts are requested to remain confidential. These materials contain commercial trade secret information that would reveal our unique proprietary system design which is a result of our proprietary Research and Development. These materials comprise information that differentiates our products from those of our significant market competition, and which allow us operate in the very competitive market for this product. These materials, if released, would result in substantial competitive harm due to unlicensed copying of our proprietary design(s) in whole or in part. To protect these materials, Nucomm does not release them to the public, and protects them from unauthorized disclosure by third parties via the execution of Non-Disclosure Agreement’s. In respect to the internal photographs of the Final Power Amplifiers, Nucomm feels that additional justification for confidentiality exists due to the fact that the amplifier circuit board(s) are mounted inside a sealed component that can sustain damage upon opening, and that said component itself is mounted inside an enclosure that the end-user may not readily open, and that so opening would nullify any equipment warranty since the equipment is only serviceable by Nucomm or our designated technicians, and that the all internal photographs of the amplifier would provide any reasonably savvy RF engineer the means to replicate the amplifier and result in substantial competitive harm to Nucomm. Nucomm requests that these materials be withheld from public inspection in perpetuity due to the possibility and likelihood that the designs will be utilized, in whole or in part, by Nucomm as the basis for future products which would likewise be subject to the same competitor interest. . John B Payne IV, Chief Engineer Nucomm, Inc.

Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 1 of 8 Nucomm - FCC Certification Report Product Photographs Newscaster VT2 Digital/Analog ENG/OB Van Transmitter FCC ID: I4U27VT2-L5-E1P5 Product Model Number: 2/7NCVT2-L5E1.5-326-A2C2K (Per CFR TITLE 47, PART 2, SUB-PART J) Nucomm, Inc. 101 Bilby Road Hackettstown, NJ 07840 Tel: 908 852-3700 FAX: 908 813-0399 www.Nucomm.com Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 2 of 8 PROPRIETARY INFORMATION This document contains proprietary information, which shall not be reproduced or transferred to other documents or disclosed to others or used for manufacturing or any other purpose without prior written permission of: Nucomm, INCORPORATED 101 Bilby Road Hackettstown, NJ 07840 Specifications are subject to change in order to allow for the introduction of design improvements Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 3 of 8 Table of Contents 1 INTRODUCTION ...................................................................................................................................................................... 6 1.1 NCVT2 DUAL BAND TRUCK UNIT PRODUCT PHOTOGRAPH................................................................................................ 7 Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 4 of 8 List of Tables Table 1 Revision History ....................................................................................................................5 List of Figures Figure 1: Front View of Product..........................................................................................................7 Figure 2: Rear View of Product ..........................................................................................................8 Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 5 of 8 Table 1 Revision History Date Revision Changed by Reason for Change 3/26/07 1.0 George Williamson Initial release. Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 6 of 8 1 Introduction This document contains photographs depicting the Dual Band News Caster Truck transmitter and Control Drawer of the NCVT2 unit model number 2/7NCVT2-L5E1.5-326-A2C2K required to support the FCC type certification (Per CFR TITLE 47, PART 2, SUB-PART J). It is an addendum to the Nucomm - FCC Certification Report for I4U27VT2-L5-E1P5. Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 7 of 8 1.1 NCVT2 Dual Band Truck Unit Product photograph Figure 1: Front View of Product Nucomm NCVT2 FCC Technical Report (I4U27VT2-L5-E1P5) Date: 3/26/07 Revision: 1.0 Page 8 of 8 Figure 2: Rear View of Product

Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 3 Date: 3/18/07 Revision: 1.0 Page 1 of 5 Nucomm - FCC Certification Report Addendum 3 FCC Identification Location FCC ID: I4U27VT2-L5-E1P5 Product Model Number: 2/7NCVT2-L5E1.5-326-A2C2K Newscaster VT2 Dual Band (2/7 GHz) Digital/Analog ENG/OB Van Transmitter (Per CFR TITLE 47, PART 2, SUB-PART J) Nucomm, Inc. 101 Bilby Road Hackettstown, NJ 07840 Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 3 Date: 3/18/07 Revision: 1.0 Page 2 of 5 Tel: 908 852-3700 FAX: 908 813-0399 www.Nucomm.com PROPRIETARY INFORMATION This document contains proprietary information, which shall not be reproduced or transferred to other documents or disclosed to others or used for manufacturing or any other purpose without prior written permission of: Nucomm, INCORPORATED 101 Bilby Road Hackettstown, NJ 07840 Specifications are subject to change in order to allow for the introduction of design improvements Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 3 Date: 3/18/07 Revision: 1.0 Page 3 of 5 Table of Contents 1 INTRODUCTION.........................................................................................................................5 1.1 FCC EQUIPMENT IDENTIFICATION PLATE..................................................................................5 List of Tables Table 1 Revision History ....................................................................................................................4 List of Figures Figure 1: FCC Equipment Identification Plate ....................................................................................5 Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 3 Date: 3/18/07 Revision: 1.0 Page 4 of 5 Table 1 Revision History Date Revision Changed by Reason for Change 3/18/07 1.0 George Williamson Initial release. Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 3 Date: 3/18/07 Revision: 1.0 Page 5 of 5 1 Introduction This document contains the photograph depicting the location of the FCC Identifier on the Channel Master Portable unit model number 2/7NCVT2-L5E1.5-326-A2C2K required to support the FCC type certification (Per CFR TITLE 47, PART 2, and SUB-PART J). It is an addendum to the Nucomm - FCC Certification Report dated 3/18/07. 1.1 FCC Equipment Identification Plate Figure 1: FCC Equipment Identification Plate

Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 4 Date: 3/3/07 Revision: 1.0 Page 1 of 5 Nucomm - FCC Certification Report Addendum 4 FCC Equipment Identification Plate FCC ID: I4U27VT2-L5-E1P5 Product Model Number: 2/7NCVT2-L5E1.5-326-A2C2K Newscaster VT2 Dual Band (2/7 GHz) Digital/Analog ENG/OB Van Transmitter (Per CFR TITLE 47, PART 2, SUB-PART J) Nucomm, Inc. 101 Bilby Road Hackettstown, NJ 07840 Tel: 908 852-3700 FAX: 908 813-0399 Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 4 Date: 3/3/07 Revision: 1.0 Page 2 of 5 www.Nucomm.com PROPRIETARY INFORMATION This document contains proprietary information, which shall not be reproduced or transferred to other documents or disclosed to others or used for manufacturing or any other purpose without prior written permission of: Nucomm, INCORPORATED 101 Bilby Road Hackettstown, NJ 07840 Specifications are subject to change in order to allow for the introduction of design improvements Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 4 Date: 3/3/07 Revision: 1.0 Page 3 of 5 Table of Contents 1 INTRODUCTION.........................................................................................................................5 1.1 FCC EQUIPMENT IDENTIFICATION PLATE..................................................................................5 List of Tables Table 1 Revision History ....................................................................................................................4 List of Figures Figure 1: FCC Equipment Identification Plate ....................................................................................5 Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 4 Date: 3/3/07 Revision: 1.0 Page 4 of 5 Table 1 Revision History Date Revision Changed by Reason for Change 3/18/07 1.0 George Williamson Initial release. Nucomm NCVT2 Dual Band FCC Technical Report (2/7NCVT2-L5E1.5-326-A2C2K) Addendum 4 Date: 3/3/07 Revision: 1.0 Page 5 of 5 1 Introduction This document contains the photograph depicting the location of the FCC Identifier on the Channel Master Portable unit model number 2/7NCVT2-L5E1.5-326-A2C2K required to support the FCC type certification (Per CFR TITLE 47, PART 2, and SUB-PART J). It is an addendum to the Nucomm - FCC Certification Report dated 3/18/07. 1.1 FCC Equipment Identification Plate Figure 1: FCC Equipment Identification Plate

Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 1 of 30 GENERAL INFORMATION REQUIREMENTS Paragraph 2.983(a) Name of Applicant: Nucomm, Inc. Address of Applicant: 101 Bilby Road Hackettstown, NJ 07840 Name of Manufacturer: Nucomm, Inc. Paragraph 2.983(b) Equipment Identification: FCC ID: I4U27VT2-L5-E1P5 Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 2 of 30 Para. 2.1053 FIELD STRENGTH of SPURIOUS EMISSIONS, EFFECTIVE RADIATED POWER Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 3 of 30 FIELD STRENGTH of SPURIOUS EMISSIONS, EFFECTIVE RADIATED POWER (Para. 2.1053) A. Measurement Procedure: The spurious emissions of the transmitter from 30 MHz to 40 GHz were measured in accordance with TIA/EIA603, Paragraph 2.2.1.2 as described below: The transmitter under test was placed on an 80-cm high non-metallic table on the Open Air Test Site with its antenna terminated into a shielded load. A receive antenna was placed three meters away from the transmitter. The turntable was rotated 360 degrees and the receive antenna was raised and lowered from 1 to 4 meters until a maximum reading was obtained at each spurious emission detected. This reading was recorded. The transmitter under test was replaced with a dipole (or equivalent antenna) and signal generator. The signal generator was set to the frequency for the spurious emission. The level of the signal generator was increased until the level was equal to that previously measured. The required input level from the signal generator in dBm was recorded and the antenna gain (in dB) of the transmit antenna was added. This was the Effective Radiated Power of the spurious emission. Setup of the test is shown below: A. Test Results: The EUT was found to comply with the requirements specified for this test method Spectrum Analyzer Test Sample 3M 4M Broadband Antenna Pre Amplifier Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 4 of 30 EQUIPMENT LIST TIA/EIA-603-1992, Section 2.2.12, Radiated Spurious Emissions (30MHz – 40GHz) EN Type Manufacturer Description Model No. Cal Date Due Date 067 Open Area Test Site Retlif 3 Meter RNY 9/12/2006 9/12/2009 127B Biconical Antenna Electro-Metrics 20 MHz - 200 MHz BIA-25 6/5/2006 6/5/2007 128 Double Ridged Guide Electro-Mechanics 1 GHz - 18 GHz 3105 3/27/2006 3/27/2007 133 Broadband Pre-Amplifier Electro-Metrics 10 kHz - 1 GHz, 26dB BPA-1000 6/27/2006 6/27/2007 206B 6.0 dB Attenuator Texscan 0 - 1.0 GHz FP-50 - 6 dB 6/27/2006 6/27/2007 450B Tuned Dipole Antenna Empire Devices 140 - 400 MHz DM-105-T2 8/12/2003 11/12/2006 450C Tuned Dipole Antenna Empire Devices 400 - 1000 MHz DM-105-T3 8/12/2003 11/12/2006 543 Preamplifier Hewlett Packard 1.0 GHz - 26.5 GHz 8449B 9/9/2005 9/9/2007 574 AM/FM Signal Generator Marconi Instru. 9 kHz - 2.4 GHz 2024 7/25/2006 7/25/2007 648A Power Meter Boonton Electronics 10 kHz - 100 GHz 4232A 6/1/2006 6/1/2007 649A Power Sensor Boonton Electronics 10 kHz - 8 GHz 51011-EMC 10/20/2005 10/25/2006 712A Cable Retlif 10 kHz - 18 GHz R&S Analyzer 6/3/2006 6/3/2007 712B Cable Retlif 10 kHz - 18 GHz R&S Analyzer 8/21/2006 8/21/2007 712C Cable Retlif 10 kHz - 18 GHz R&S Analyzer 6/3/2006 6/3/2007 723 H.P. Filter Mini-Circuits 1 GHz BHP-1000 8/7/2006 8/7/2007 731 Log Periodic Antenna Electro-Metrics 200 - 1000 MHz LPA-30 3/17/2006 3/17/2007 763 Spectrum Analyzer Agilent 30 Hz - 13.2 GHz E4405B 8/18/2006 8/18/2007 Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 5 of 30 Test Method: TIA / EIA-603-1992, Section 2.2.12, Radiated Spurious Emissions ( 30 MHz – 26 GHZ) Customer: Nucomm, Inc. Job No.: R-11489 Test Sample: 2 GHz / 7 GHz Digital / Analog ENG/OB Van Transmitter. Part No.: 2 / 7NCVT2-L5E1.5-326-A2C2K FCC ID.: I4U27VT2-L5-E1P5 Operating Mode: Color bars plus audio, High power, Channel 1, Analog FM Modulation, 12 MHz channel Transmitting at 2031.5 MHz. Technician: R. Soodoo Date: October 12, 2006. Notes: Test Distance: 3 Meters Temp: 20°C Humidity: 15% Detector: Peak Limit: ( 43+10 log P) down from fundamental level = -13dBm Frequency Antenna Position EUT Orientation Meter Readings Power Meter Reading Gain Above Isotropic Cable loss ERP Limit MHz (V/H) / Meters Degrees dBuV dBm dB dB dBm dBm 30.00 -13.0 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 26000.0 -13.0 The EUT was placed on a table, and the radiated output level was measured with a receive antenna. After the level was maximized, the EUT was replaced with a transmit antenna and a signal generator. The level of the generator was raised until it matched the level recorded from the EUT and this plus the antenna gain was considered the output power. All emissions not recorded were more than 20 dB below the limit Page 1 of 26 NO EMISSIONS OBSERVED AT THE SPECIFIED TEST DISTANCE Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 6 of 30 Test Method: TIA / EIA-603-1992, Section 2.2.12, Radiated Spurious Emissions ( 30 MHz – 26 GHZ) Customer: Nucomm, Inc. Job No.: R-11489 Test Sample: 2 GHz / 7 GHz Digital / Analog ENG/OB Van Transmitter. Part No.: 2 / 7NCVT2-L5E1.5-326-A2C2K FCC ID.: I4U27VT2-L5-E1P5 Operating Mode: Color bars plus audio, High power, Channel 1, Digital COFDM Modulation, 12 MHz channel Transmitting at 2031.5 MHz. Technician: R. Soodoo Date: October 12, 2006. Notes: Test Distance: 3 Meters Temp: 20°C Humidity: 15% Detector: Peak Limit: ( 43+10 log P) down from fundamental level = -13dBm Frequency Antenna Position EUT Orientation Meter Readings Power Meter Reading Gain Above Isotropic Cable loss ERP Limit MHz (V/H) / Meters Degrees dBμV dBm dB dB dBm dBm 30.00 -13.0 | | | | | | | | | | | | | | | | | | 378.0 H / 1.0 158.0 48.4 -53.7 2.2 1.6 -49.9 | | | | | |…

Text truncated - open the document above for the full version.

Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 1 of 34 GENERAL INFORMATION REQUIREMENTS Paragraph 2.983(a) Name of Applicant: Nucomm, Inc. Address of Applicant: 101 Bilby Road Hackettstown, NJ 07840 Name of Manufacturer: Nucomm, Inc. Paragraph 2.983(b) Equipment Identification: FCC ID: I4U27VT2-L5-E1P5 Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 2 of 34 Para. 2.1051 Spurious Emissions at Antenna Terminals Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 3 of 34 Spurious Emissions at Antenna Terminals (Para. 2.1051) A. Measurement Procedure: The RF output of the transmitter was directly coupled through either attenuators or a waveguide transmission line to the input of a spectrum analyzer. With the transmitter on, the spectrum analyzer was swept from 30 MHz to 26 or 40 GHz. (Dependant of fundamental operating frequency). It was verified that all emissions not associated with the fundamental transmission were at least 43 +10 log (P) down from the fundamental transmit power level (P). Setup of the test is shown below: B. Test Results: The EUT was found to comply with the requirements specified for this test method. Spectrum Analyzer Test Sample Attenuator Or Waveguide RF Output Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 4 of 34 EQUIPMENT LIST FCC Part 2, Antenna Conducted Emissions. EN Type Manufacturer Description Model No. Cal Date Due Date 032G H.P. Filter Microlab/FXR 3 GHz HA-30N 5/25/2006 5/25/2007 1008 20.0 dB Attenuator Narda DC - 18 GHz 776C-20 11/29/2005 11/29/2006 1009 30.0 dB Attenuator Narda DC - 18 GHz 776C-30 11/29/2005 11/29/2006 896 EMI Test Receiver Rohde & Schwarz 20 Hz - 40 GHz ESIB40 9/5/2006 9/5/2007 R126 Signal Generator Hewlett Packard 10 MHz - 40 GHz 83640B 8/2/2005 8/2/2007 Applicant: Nucomm, Inc. FCC ID: I4U27VT2-L5-E1P5 Retlif Testing Laboratories Report No.: R-11489 Page 5 of 34 2 GHz Antenna Port Conducted Emissions, 12 MHz channel spacing plan Page 6 of 34 Retlif Testing Laboratories, Job Number R-11489 FCC Antenna Conducted Emissions, 30 MHz to 26 GHz Customer: Nucomm, Inc. Test Sample: 2 GHz / 7 GHz Digital/Analog ENG/OB Van Transmitter Part Number: 2/7NCVT2-L5E1.5-326-A2C2K FCC ID Number: I4U27VT2-L5-E1P5 Equipment Settings: Color bars plus audio, High power, Channel 1, Analog FM Modulation, 12 MHz channel Transmitting at 2031.5 MHz. Antenna Port Tested: 2 GHz Directional / 12 MHz Channel Test Engineer / Date: D. Lerner / October 6, 2006 Notes: Fundamental frequency exempt from -13 dBm -80-60-40-20 0 2040 Level [dBm] 30M 100M 200M 400M 1G 2G 3G 5G 10G 26G Frequency [Hz] Sheet 1 of 8 Page 7 of 34 Retlif Testing Laboratories, Job Number R-11489 FCC Antenna Conducted Emissions, 30 MHz to 26 GHz Customer: Nucomm, Inc. Test Sample: 2 GHz / 7 GHz Digital/Analog ENG/OB Van Transmitter Part Number: 2/7NCVT2-L5E1.5-326-A2C2K FCC ID Number: I4U27VT2-L5-E1P5 Equipment Settings: Color bars plus audio, High power, Channel 1, Digital COFDM Modulation, 12 MHz channel Transmitting at 2031.5 MHz. Antenna Port Tested: 2 GHz Directional / 12 MHz Channel Test Engineer / Date: D. Lerner / October 6, 2006 Notes: Fundamental frequency exempt from -13 dBm -80-60-40-20 0 2040 Level [dBm] 30M 100M 200M 400M 1G 2G 3G 5G 10G 26G Frequency [Hz] Sheet 2 of 8 Page 8 of 34 Retlif Testing Laboratories, Job Number R-11489 FCC Antenna Conducted Emissions, 30 MHz to 26 GHz Customer: Nucomm, Inc. Test Sample: 2 GHz / 7 GHz Digital/Analog ENG/OB Van Transmitter Part Number: 2/7NCVT2-L5E1.5-326-A2C2K FCC ID Number: I4U27VT2-L5-E1P5 Equipment Settings: Color bars plus audio, High power, Channel 3, Analog FM Modulation, 12 MHz channel Transmitting at 2055.5 MHz. Antenna Port Tested: 2 GHz Directional / 12 MHz Channel Test Engineer / Date: D. Lerner / October 6, 2006 Notes: Fundamental frequency exempt from -13 dBm -80-60-40-20 0 2040 Level [dBm] 30M 100M 200M 400M 1G 2G 3G 5G 10G 26G Frequency [Hz] Sheet 3 of 8 Page 9 of 34 Retlif Testing Laboratories, Job Number R-11489 FCC Antenna Conducted Emissions, 30 MHz to 26 GHz Customer: Nucomm, Inc. Test Sample: 2 GHz / 7 GHz Digital/Analog ENG/OB Van Transmitter Part Number: 2/7NCVT2-L5E1.5-326-A2C2K FCC ID Number: I4U27VT2-L5-E1P5 Equipment Settings: Color bars plus audio, High power, Channel 3, Digital COFDM Modulation, 12 MHz channel Transmitting at 2055.5 MHz. Antenna Port Tested: 2 GHz Directional / 12 MHz Channel Test Engineer / Date: D. Lerner / October 6, 2006 Notes: Fundamental frequency exempt from -13 dBm -80-60-40-20 0 2040 Level [dBm] 30M 100M 200M 400M 1G 2G 3G 5G 10G 26G Frequency [Hz] Sheet 4 of 8 Page 10 of 34 Retlif Testing Laboratories, Job Number R-11489 FCC Antenna Conducted Emissions, 30 MHz to 26 GHz Customer: Nucomm, Inc. Test Sample: 2 GHz / 7 GHz Digital/Analog ENG/OB Van Transmitter Part Number: 2/7NCVT2-L5E1.5-326-A2C2K FCC ID Number: I4U27VT2-L5-E1P5 Equipment Settings: Color bars plus audio, High power, Channel 5, Analog FM Modulation, 12 MHz channel Transmitting at 2079.5 MHz. Antenna Port Tested: 2 GHz Directional / 12 MHz Channel Test Engineer / Date: D. Lerner / October 6, 2006 Notes: Fundamental frequency exempt from -13 dBm -80-60-40-20 0 2040 Level [dBm] 30M 100M 200M 400M 1G 2G 3G 5G 10G 26G Frequency [Hz] Sheet 5 of 8 Page 11 of 34 Retlif Testing Laboratories, Job Number R-11489 FCC Antenna Conducted Emissions, 30 MHz to 26 GHz Customer: Nucomm, Inc. Test Sample: 2 GHz / 7 GHz Digital/Analog ENG/OB Van Transmitter Part Number: 2/7NCVT2-L5E1.5-326-A2C2…

Text truncated - open the document above for the full version.