JQU801800CNon-multilateration LMS Transponder

EN Doc No.: 801850-TAB_Rev_E Janus™ Front Mount Exterior (FME) Transponder Mounting Instructions The FME transponder is recommended for when the interior transponder cannot be used. Requirements • For reliable operation of the transponder, the vehicle must be equipped with only one correctly mounted TDM transponder while passing through a toll facility. Other TDM transponders present in or on the vehicle must be switched off or enclosed in an RF shield. • FME transponders must be mounted in the location for which they were programmed. FME transponders programmed for License Plate must be mounted on the front of the vehicle. FME transponders programmed for Rooftop must be mounted on the roof. • The mounting location must provide direct line-of-sight communication between the transponder and the toll facility’s overhead antenna. • FME transponders cannot be used where local regulations prohibit externally mounting transponders on the roof of the vehicle, the front license plate, front bumper, or other external surfaces • The presence of certain classes of front impact-absorbing materials used in the construction of the vehicle may affect the operation of the FME transponder. The mounting location must be free of such materials. • Apply Dual Lock™ Reclosable Fasteners in accordance with 3M™ document 70-0709-4029-4. 2. Select the transponder mounting location on the front bumper at the center of the vehicle (as measured from the right and left sides of the vehicle), 15 to 21 in. from the top of the transponder to the road surface. 3. Using rubbing alcohol, clean the mounting location on the bumper. Allow the mounting location to dry completely. 4. Remove the remaining protective backing from the five Dual Lock fasteners and press the transponder onto the mounting location on the bumper, ensuring the orientation arrows are pointing skyward. Maintain pressure for 15 seconds to ensure a good bond. 5. Remove the transponder by lifting any corner with sufficient force to separate the Dual Lock strips. Do not reuse the Dual Lock strips after removing them from the bumper. Obtain new strips as required. centerline of vehicle 15 to 21 in. road surface Preferred Mounting Location - the front license plate using the existing license plate mounting screws. 1. Remove the two upper license plate mounting screws securing the license plate to the front of the vehicle. 2. Using the license plate mounting screws removed in step 1, secure the transponder, with arrows pointing skyward, and the license plate to the front of the vehicle. Optional Mounting Location - the front bumper using 3M™ Dual Lock™ fasteners. 1. Apply one side of five 3M™ Dual Lock Fasteners to the FME in accordance with the 3M™ document 70-0709-4029-4. a. Using rubbing alcohol, clean the rear surface of the transponder to ensure the bonding surface is free of dirt and any surface contaminants. b. Allow the rear surface of the transponder to dry completely. c. Cut the Dual Lock fastener into five 1 in. lengths. d. Remove the protective backing from one side of the five Dual Lock fasteners and apply the fasteners equally spaced on the rear of the transponder. Dual Lock™ Reclosable Fasteners Passenger Vehicle Front Mounting orientation arrow (pointing skyward) license plate mounting screw Trucks & Buses Front Mounting FME transponders programmed for front mounting only. Select a mounting location either on the front license plate using the license plate mounting screws or on the front of the vehicle using the mounting plate. Consider the following criteria: A. a minimum of 24 in. clearance if bumper or large object extends 7+ in. (A 1 ). B. a minimum of 15 in. from the top of the transponder to the roadway for front bumper mounting. C. the transponder must be mounted within 4 in. of the vehicle center. If mounting the transponder on the front license plate: 1. Remove the two upper license plate mounting screws securing the license plate to the front of the vehicle. 2. Using the license plate mounting screws removed in step 1, secure the transponder, with orientation arrows pointing skyward, and the license plate to the front of the vehicle. orientation arrow (pointing skyward) license plate mounting screw A 1 A B C If mounting the transponder horizontally on the front of the vehicle: 1. The back of the mounting plate is covered with 3M™ VHB™ acrylic foam tape. Prepare the mounting location in accordance with 3M™ document 70-0704-8701-5. NOTE: Ensure the mounting plate is installed on the vehicle so that when the transponder is installed on the mounting plate, the orientation arrows on the transponder point skywards. 2. Remove the protective backing from the adhesive on the back of the mounting plate and firmly press the mounting plate against the mounting surface with either a roller or platen pressure, maintaining pressure for 15 seconds to ensure a good bond. 3. Using the supplied tamper-proof nuts, lock washers, and flat washers, secure the transponder to the mounting plate with the notches on the transponder and mounting plate aligned and with the orientation arrows on the transponder pointing in the direction of forward travel. tamper-proof nut notch lockwasher orientation arrow transponder notch mounting plate stud flat washer mounting plate FME Transponder with Mounting Plate Trucks & Buses Roof Mounting FME transponders programmed for roof top mounting only. Select a mounting location within 4 in. of the centerline (as measured from the right and left sides of the vehicle). Consider the following criteria:  Do not mount behind horns, lights, or other metal objects.  Do not mount within 6 in. of any metal object (trailer, decals, horn, lights, or metallic paint-cover surfaces.  A non-metal air dam may cover the transponder provided that no metallic paint or metal foil decals cover the dam.  Do not mount within 2 ft. of any radio transmitter.  Do not mount on a slope (+/- 5 deg.) 13 ft.  Do not mount more than 13 ft. above roadway…

Text truncated - open the document above for the full version.

Kapsch TrafficCom Canada Inc.| 6020 Ambler Drive | Mississauga, Ontario L4W 2P1 | Canada | T: 905-624-3020 | F 905 625 6197 | www.kapsch.net Kapsch TrafficCom Jul 27, 2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) Filing Re. KDB 986446 D01 FCC ID: JQU 801800C Dear Sir or Madam, Kapsch Traffic Com Canada Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please contact us. Sincerely, Dated this 27 Day of July 2023 By Alastair Malarky, Chief Engineer On Behalf Of Kapsch TrafficCom Canada Inc. Contact information [email protected] +1 416-451-0223

Kapsch TrafficCom Canada Inc.| 6020 Ambler Drive | Mississauga, Ontario L4W 2P1 | Canada | T: 905-624-3020 | F 905 625 6197 | www.kapsch.net Kapsch TrafficCom Feb 26, 2024 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: JQU 801800C Dear Sir or Madam, Kapsch TrafficCom Canada Inc. (“the applicant”) certifies that, as of the date of the filing of the application, it has designated Corporation Service Company, 1090 Vermont Avenue NW, Washington, DC 20005 as Applicant’s designated U.S. agent to receive service of process for the above referenced FCC ID. Kapsch TrafficCom Canada Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Dated this 26th Day of February 2024 By Alastair Malarky, Chief Engineer On Behalf Of Kapsch TrafficCom Canada Inc. Contact information [email protected] +1 416-451-0223 Applicant FRN 0021821640 Agent Corporation Service Company accepts appointment to receive service of process for Kapsch TrafficCom Canada, Inc. By: ___________________________ Date: 26 Feb 2024 Authorized Representative Corporation Service Company Email: [email protected] Agent FRN statement Corporation Service Company does not have a FRN as it is not an entity doing business with the FCC, where doing business with the FCC is defined as “a filer, licensee, certificate holder, or an entity sending payments to the FCC:”

Kapsch TrafficCom Canada Inc.| 6020 Ambler Drive | Mississauga, Ontario L4W 2P1 | Canada | T: 905-624-3020 | F 905 625 6197 | www.kapsch.net Kapsch TrafficCom Aug, 24, 2023 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 USA Confidentiality Request for FCC ID: JQU801800C Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, we, Kapsch TrafficCom Canada Inc hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Parts Lists and Tune-up procedure Operation Description Block Diagram Kapsch TrafficCom Canada Inc hereby also hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of 180 days: Internal Photographs The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Dated this 24 Day of August 2023 By Alastair Malarky, Chief Engineer On Behalf Of Kapsch TrafficCom Canada Inc.

Kapsch TrafficCom Kapsch TrafficCom Canada Inc. | 6020 Ambler Drive | Mississauga, ON L4W 2P1 | Canada | Phone 905 624 3020 | Fax 905 625 6197 | www.kapsch.net Date: July 7, 2023 TUV SUD America Inc. 10 Centennial Drive Peabody, MA 01960 USA Dear Sir or Madam, We, Kapsch TrafficCom Canada Inc., hereby authorize TUV SUD Canada Inc., 11 Gordon Collins, Gormley, L0H 1G0, Canada; 905-883-7255 to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on July 7, 2024. Yours Sincerely, Name Alastair Malarky Title Chief Engineer On Behalf Of Kapsch TrafficCom Canada Inc.

© 2023 Kapsch TrafficCom Canada Inc., all rights reserved. Kapsch TrafficCom Info Number 801800C Application Author Alastair Malarky Date 2023 08 22 JANUS™ Front Mount Exterior (FME) OBU – 801800C-TAB External Photographs References: FCC: JQU801800C IC: 2665A-801800C 801800C Label and Location Model 801800C -TAB Top View © 2023 Kapsch TrafficCom Canada Inc., all rights reserved. Kapsch TrafficCom Model 801800C –TAB Bottom View Model 801800C –TAB Top Long Side View Permanent Label

© 2023 Kapsch TrafficCom Canada Inc., all rights reserved. Kapsch TrafficCom Info Number 801800C Application Author Alastair Malarky Date 2023 08 22 To TUV SUD Canada Inc JANUS™ Front Mount Exterior (FME) OBU – 801800C-TAB – Label and Location References: FCC: JQU801800C IC: 2665A-801800C The following defines the label and the location of the label for the JANUS™ Front Mount Exterior (FME) OBU – 801800C-TAB Due to the need to place other jurisdiction regulatory permanent labels on the certain models, it is not considered practical to place the information required by 47 CFR Part 15 on those models such that it is readable. Therefore in accordance with 47 CFR 15.19 (5) for those models the statement required by Part 15 is provided in the mounting instructions that are to be supplied to the user, a copy of which is included in this application. Label Size For model 801800C-TAB the permanent label is 57.15 mm by 25.40 mm on the back of the unit. It is shown in the following drawing. © 2023 Kapsch TrafficCom Canada Inc., all rights reserved. Kapsch TrafficCom Label Location The label is located on the rear of each unit and is engraved into the unit. The unit rear is shown in the following picture. Rear view of Model 801800C-TAB Note the picture does not show the final version of the permanent label text – this is shown in the next section. Permanent Label © 2023 Kapsch TrafficCom Canada Inc., all rights reserved. Kapsch TrafficCom Rear view of Model 801800C-TAB Labelling area

© 2023 Kapsch TrafficCom Canada Inc., all rights reserved. These drawings and specifications contain confidential and proprietary information and are the property of Kapsch TrafficCom Canada Inc. and are issued in strict confidence and will be kept confidential and used solely for the purpose intended and for no other purpose and shall not be transmitted, reproduced, copied, and/or used as the basis for manufacture or sale of apparatus unless otherwise agreed to in writing by Kapsch TrafficCom Canada Inc. . Kapsch TrafficCom Info Number 801800C Application Author Alastair Malarky Date 2023 08 23 To TUV SUD JANUS™ Front Mount Exterior (FME) OBU – 801800C-TAB Internal Photographs References: FCC: JQU801800C IC: 2665A-801800C The internal photographs of the model tested are shown below. © 2023 Kapsch TrafficCom Canada Inc., all rights reserved. These drawings and specifications contain confidential and proprietary information and are the property of Kapsch TrafficCom Canada Inc. and are issued in strict confidence and will be kept confidential and used solely for the purpose intended and for no other purpose and shall not be transmitted, reproduced, copied, and/or used as the basis for manufacture or sale of apparatus unless otherwise agreed to in writing by Kapsch TrafficCom Canada Inc. . Kapsch TrafficCom PWA Front Photo – Model 801800C -TAB © 2023 Kapsch TrafficCom Canada Inc., all rights reserved. These drawings and specifications contain confidential and proprietary information and are the property of Kapsch TrafficCom Canada Inc. and are issued in strict confidence and will be kept confidential and used solely for the purpose intended and for no other purpose and shall not be transmitted, reproduced, copied, and/or used as the basis for manufacture or sale of apparatus unless otherwise agreed to in writing by Kapsch TrafficCom Canada Inc. . Kapsch TrafficCom PWA Back Photo – Model 801800C -TAB © 2023 Kapsch TrafficCom Canada Inc., all rights reserved. These drawings and specifications contain confidential and proprietary information and are the property of Kapsch TrafficCom Canada Inc. and are issued in strict confidence and will be kept confidential and used solely for the purpose intended and for no other purpose and shall not be transmitted, reproduced, copied, and/or used as the basis for manufacture or sale of apparatus unless otherwise agreed to in writing by Kapsch TrafficCom Canada Inc. . Kapsch TrafficCom PCA in a Housing Photo – Model 801800C -TAB

Report File #: 7169013070RFE-FCC-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Exhibit: RF Exposure – FCC FCC ID: JQU801800C Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) FCC KDB 447498 v07 Page 2 of 4 Report Issued: 8/15/2023 Report File #: 7169013070RFE-FCC-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. RF Exposure Calculation (FCC) Purpose The purpose of this test is to ensure that the RF energy transmitted at a specified operating distance from the human body meets the criteria to be exempt from routine evaluation. The RF Exposure values are calculated based upon measurements obtained during testing and are compared to the applicable exposure limits for individual RF sources. If multiple RF sources are used within a host product, and they operate simultaneously, an additional exemption criterion based on total exposure from multiple RF sources is also applied. If the exemption criteria are not met, the RF sources may be required to undergo routine evaluation for RF Exposure. Limit(s) and Method The test method and exemption limits are defined in FCC KDB 447498 and FCC 1.1307(b)(3) and are applicable to both unintentional and intentional RF sources, whether portable, mobile, or fixed installations. Individual RF Sources For individual sources, the following three exemption criteria options are defined. Any of the three options may be used to determine the RF source to be exempt from routine evaluation if it meets the corresponding exemption limit. Defined in FCC 1.1307(b)(3)(i)(A), Exemption Criteria Option A is based on the maximum time-averaged output power. The requirement is that this measurement must not exceed 1mW, regardless of separation distance, and in the frequency range of 100kHz-100GHz. Defined in FCC 1.1307(b)(3)(i)(B), Exemption Criteria Option B is based on SAR using the measurement of maximum time-averaged output power or ERP, whichever is greater. This option is applicable to separation distances of 0.5cm-40cm and in the frequency range of 300MHz-6GHz. The limit is defined below: Defined in FCC 1.1307(b)(3)(i)(C), Exemption Criteria Option C is based on MPE using the ERP measurement. This option is only applicable for separation distances greater than Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) FCC KDB 447498 v07 Page 3 of 4 Report Issued: 8/15/2023 Report File #: 7169013070RFE-FCC-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. or equal to the wavelength of the frequency under consideration divided by 2π, and in the frequency range of 300kHz-100GHz. The limit is defined below: Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) FCC KDB 447498 v07 Page 4 of 4 Report Issued: 8/15/2023 Report File #: 7169013070RFE-FCC-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Results The EUT is exempt from routine evaluation of RF exposure based on the following calculations: Single RF Source 1 Analysis – 915MHz Transmitter The transmitter has maximum output power at the operating frequency of 915MHz. The transmitter antenna is located 5mm from the EUT enclosure and therefore the separation distance has been taken as 5mm as a worst-case scenario. The peak ERP measured during continuous transmission was also used as a worst-case scenario, no time averaging is considered. Frequency (MHz): 915.0 Separation Distance (cm): 0.5 ERP (dBm): 3.34 ERP (mW): 2.16 Exemption Criteria Option B: Threshold Power = 8.13mW 2.16mW < 8.13mW Option B is applicable. Contribution Ratio = 2.16/8.13 = 0.265 Therefore, the RF source is exempt from routine evaluation based on Exemption Criteria Option B with contribution ratio of 0.265.

Registration # 6844A-3 Testing Laboratory Certificate #2955.02 Registration # CA6844 Page 1 of 33 Report Issued: 8/25/2023 Report File #: 7169013405RF-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc FCC 15 247 Rev2 RF Test Report As per RSS-137 Issue 2:2009 & FCC Part 90 Subpart M:2015 Location and Monitoring Service (LMS) Operation in the 902 -928 MHz Band on the JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Issued by: TÜV SÜD Canada Inc. 11 Gordon Collins Dr, Gormley, ON, L0H 1G0 Canada Ph: (905) 883-7255 Testing produced for See Appendix A for full client & EUT details. Prepared by Jadon Bull, Project Engineer Reviewed by Scott Drysdale, EMC Regional Manager Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 2 of 33 Report Issued: 8/25/2023 Report File #: 7169013405RF-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc Table of Contents Table of Contents ................................................................................................................... 2 Report Scope .......................................................................................................................... 3 Summary ................................................................................................................................ 4 Test Results Summary ....................................................................................................... 5 Notes, Justifications, or Deviations ................................................................................... 6 Sample Calculation(s) ........................................................................................................ 6 Applicable Standards, Specifications and Methods ............................................................... 7 Document Revision Status ..................................................................................................... 8 Definitions and Acronyms ..................................................................................................... 9 Testing Facility .................................................................................................................... 10 Calibrations and Accreditations ....................................................................................... 10 Testing Environmental Conditions and Dates ................................................................. 11 Detailed Test Results Section .............................................................................................. 12 Output Power and Antenna Heights ................................................................................ 13 Occupied Bandwidth ........................................................................................................ 15 Emission Mask ................................................................................................................. 19 Temperature Frequency Stability ..................................................................................... 29 Appendix A – EUT Summary .............................................................................................. 31 Appendix B – EUT and Test Setup Photos .......................................................................... 33 Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 3 of 33 Report Issued: 8/25/2023 Report File #: 7169013405RF-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc Report Scope This report addresses the EMC verification testing and test results of the JANUS TM Front Mount Exterior OBU,Model:801800C-TAB, and is herein referred to as EUT (Equipment Under Test). The EUT was tested for compliance against the following standards: RSS-137 Issue 2:2009 FCC Part 90 Subpart M:2015 Test procedures, results, justifications, and engineering considerations, if any, follow later in this report. The results contained in this report relate only to the item(s) tested. This report does not imply product endorsement by any government, accreditation agency, or TÜV SÜD Canada Inc. Opinions or interpretations expressed in this report, if any, are outside the scope of TÜV SÜD Canada Inc. accreditations. Any opinions expressed do not necessarily reflect the opinions of TÜV SÜD Canada Inc., unless otherwise stated. Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 4 of 33 Report Issued: 8/25/2023 Report File #: 7169013405RF-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc Summary The results contained in this report relate only to the item(s) tested. EUT: JANUS TM Front Mount Exterior OBU Model:801800C-TAB FCC Certification #, FCC ID: JQU801800C Industry Canada Certification #, IC: 2665A-801800C EUT passed all tests performed Yes Tests conducted by Jadon Bull Report Reviewed by Scott Drysdale For testing dates, see "Testing Environmental Conditions and Dates". Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 5 of 33 Report Issued: 8/25/2023 Report File #: 7169013405RF-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc Test Results Summary Standard/Method Description Class/Limit Result FCC 90.205 RSS-137 Clause 6.4 Output Power 30 W Pass FCC 90.207 RSS-137 Clause 6.2 Types of Modulation -…

Text truncated - open the document above for the full version.

Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Exhibit: Test Setup Photos FCC ID: JQU801800C IC: 2665A-801800C Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 2 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 1 ‒ EUT Close Up Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 3 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 2 ‒ Radiated Emissions Setup – 30MHz - 1GHz Note: As per ANSI C63.10-2013 Clause 6.3.1, below 1GHz, the height of the EUT was set to 80cm. Above 1GHz, the height was raised to 1.5m. Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 4 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 3 ‒ Radiated Emissions Setup – >1GHz Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 5 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 4 ‒ Radiated Emissions Setup 30MHz – 1GHz Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 6 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 5 ‒ Radiated Emissions Setup 1GHz – 10GHz Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 7 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 6 ‒ Antenna Port Conducted Emissions Setup Client Kapsch TrafficCom Canada Inc. Product JANUS TM Front Mount Exterior OBU Model: 801800C-TAB Standard(s) RSS 137 Issue 2:2009 FCC Part 90Subpart M:2015 Page 8 of 8 Report Issued: 9/13/2023 Report File #: 7169013405E-000 © TÜV SÜD Canada Inc. This test report shall not be reproduced except in full, without written approval of TÜV SÜD Canada Inc. Figure 7 ‒ Frequency Stability Setup