K9L8001TXRemote Control Transmitter

Model: 8001TX REV. 1-13-21 Page 1 INSTALLATION AND OPERATING INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This remote control system was developed to adapt most Skytech Remote Receivers to be operated by Smartplugs which are a part of many Home Automation Systems. The 8001TX can be added to most pre-existing Skytech remote control systems already installed on an appliance or fireplace. Many Skytech receivers can LEARN up to 3 security codes and you can continue to use your existing transmit- ter along with 8001TX. Some receivers can LEARN only 1 security code and the 8001TX would replace your existing transmitter. Please check with a Skytech dealer or call us directly at the number listed at the end of this manual if you need help determining the compatibility or features of your current receiver. The system operates on radio frequencies with non-directional signals. The systems operating range is approximately 30-feet. The system operates on one of 1,048,576 security codes that are programmed into the transmitter at the factory. Model: 8001TX USB Transmitter This “Smart Plug Transmitter” system is designed to be used in conjunction with a WI-FI or Bluetooth “Smart Plug” that is controlled by a voice command system (i.e. Alexa or Google) or an app downloaded on a smart phone. The Smart Plug recieves a WI-FI command or a Bluetooth command which creates a chain of command to: 1. Power the Smart Plug with 120VAC. 2. Powers a USB phone charger with 120VAC. 3. Energizes the Smart Adapter Transmitter (5VDC) to send an ON command via Radio Frequency (RF) to a typical Skytech receiver to turn ON a gas appliance or heater. See Basic Operation diagram on page 2. Note: The USB phone charger may be omitted if the Smart Plug has a switchable USB outlet. NOTE: This product is designed for use with an attended hearth appliance or fire feature. Adults must be present when the Control System is operating. DO NOT program or thermostatically set this Control to operate a hearth appliance or fire feature when adults are not physically present. Furthermore, DO NOT leave the hearth appliance or fire feature burning unattended; it may cause damage or serious injury. If an adult is going to be away from the hearth appliance or fire feature for any length of time, then the handheld/wall mount, receiver/control module and application should be in the “OFF” position. TRANSMITTER Model: 8001TX REV. 1-13-21 Page 2 WARNING This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely before attempting installation. Follow instructions carefully during installation. Any modifications of the remote control or any of its components will void the warranty and may pose a fire hazard. Do not connect any gas valve or electronic module directly to 110-120VAC power. Consult gas appliance manufacturer’s instructions and wiring schematics for proper placement of all wires. All electronic modules are to be wired to manufacturer’s specifications. The following wiring diagrams are for illustration purposes only. Follow instructions from manufacturer of gas valve and/ or electronic module for correct wiring procedures. Improper installation of electric components can cause damage to electronic module, gas valve and remote receiver. INSTALLATION INSTRUCTIONS INSTALLING TRANSMITTER Step 1: Ensure the Smart Plug (not supplied) is plugged into a working outlet and it is working properly according to the instructions supplied with the Smart Plug. The Smart Plug can be tested by plugging a light or radio into the plug, turning the light or radio ON and activating the Smart Plug to confirm the Smart Plug operates properly. Step 2: Unplug the light or radio from the Smart Plug and insert a USB Phone adapter into the Smart Plug. Note: The USB phone charger may be omitted if the Smart Plug has a switchable USB outlet. Step 3: Plug the “Smart Adapter Transmitter” into the USB Phone adapter. Installation is now complete. S m a r t P l u g P h o n e C h ar g e r Ho me O u tl e t Smart Adapter Transmitter 1. Smart Plug recieves commands via WI-FI or Bluetooth 2. Smart Plug powers USB phone charger 3. Phone Charger energizes “Smart Adapter” transmitter and sends (5VDC) ‘ON” command via RF signal to Reciever 120VAC 120VAC 5DCV SMART PLUG (not supplied) USB PHONE CHARGER SMART ADAPTER TRANSMITTER USB plug (male Jack) BASIC OPERATION Model: 8001TX REV. 1-13-21 Page 3 LEARNING TRANSMITTER TO RECEIVER Each transmitter uses a unique security code. It will be necessary to press and release the LEARN button on the receiver to accept the transmitter security code upon initial use or if a replacement transmitter is purchased from your dealer or the factory. Refer to the LEARNING SECTION of the instructions provided with the Skytech receiver you wish to control. Locate the LEARN button on the receiver. Then press and release the LEARN button. When you release the LEARN button on the receiver you will hear a “beep”. Next, activate the Smart Plug via voice or Smart Phone app. The green LED light on top of the Smart Adapter Transmitter will illuminate and send a RF signal to the receiver and the receiver will emitt three “beeps” confirming the LEARNING process is complete. At the same time the gas appliance will turn ON. S m a r t P l u g P h o n e C h ar g e r Ho me O u tl e t Smart Adapter Transmitter Green LED Light TROUBLE SHOOTING If you encounter problems with your fireplace system, the problem may be with the fireplace itself or it could be with the remote. Review the fireplace manufacturer’s operation manual to make sure all connections are properly made. Then check the operation of the remote in the following manner: • Make sure the batteries are correctly installed in the RECEIVER. One reversed battery will keep receiver from operating properly. • See LEARNING TRANSMITTER TO RECEIVER section. • Be sure Receiver…

Text truncated - open the document above for the full version.

Report Number: MLT2102P15001 Photograph of EUT

Label Format: Label Position: This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received , including Interference that may cause undesired operations. Model No: 8001TX/SP8001TX/8301TX/8001AF1TX FCC ID: K9L8001TX

Report Number: MLT2102P15001 Report Number: MLT2102P15001

Page: 1 / 33 Report Number: MLT2102P15001 (FCC : Part 15 Subpart C / ANSI C63.10-2013) Product : Remote Control Transmitter Trade Name : Skytech Model No. : 8001TX, SP8001TX, 8301TX, 8001AF1TX Applicant : Skytech II, Inc. Applicant Address : 9230 Conservation Way Fort Wayne, Indiana, 46809, USA Page: 2 / 33 Report Number: MLT2102P15001 Report Number MLT2102P15001 Applicant Skytech II, Inc. Product Remote Control Transmitter Sample Received Date 2021/2/4 Sample Tested Date 2021/2/4 ～2021/5/13 Report Prepared By Jesse Tien Signature Date Prepared 2021/5/13 Report Authorized By Roger Chen Signature Date Authorized 2021/5/13 Test By Max Light Technology Co., Ltd. No.74-4, Shibachong Xi, Shiding Dist., New Taipei City 223, Taiwan R.O.C. Office : Tel: 886-2-2363-2447 Fax: 886-2-2363-2597 Lab. : Tel: 886-2-2663-3486 Fax: 886-2-2663-3582 It may be duplicated completely for legal use with the allowance of the applicant. It shall not be reproduced except in full, without the written approval of our laboratory. This test report does not include the evaluation of MU. The test results only relate to the submitted test sample. Page: 3 / 33 Report Number: MLT2102P15001 Table of Contents : History of Test Report .............................................................................................................. 4 1. General ...................................................................................................................... 5 2. Conducted Emissions Requirements ......................................................................... 7 3. Radiated Emissions Requirements .......................................................................... 10 4. Transmitter Bandwidth Measurements .................................................................... 20 5. Transmitter Duty Cycle Measurements ................................................................... 23 6. Verification of De-activation after 5 seconds ........................................................... 28 Appendix I - EUT Test Setup ................................................................................................. 31 Appendix II – Brand / Trade Name & Model No. Multiple Listee ............................................ 33 Page: 4 / 33 Report Number: MLT2102P15001 History of Test Report Original Report Issue Date: 2021/5/13 ■ No additional attachment □ additional attachments were issued as in the following record: Attachment No. Issue Date Description MLT2102P15001 2021/5/13 Original report Page: 5 / 33 Report Number: MLT2102P15001 1. General 1.1 Introduction The following measurement report is submitted on behalf of Skytech II, Inc. In support of an Intentional Periodic Radiator certification in accordance with Part 2 Subpart J and Part 15 Subpart A and C of the Commission’s and Regulations. 1.2 Customer Details Applicant Name Skytech II, Inc. Applicant Address 9230 Conservation Way Fort Wayne, Indiana, 46809, USA Manufacturer Name FEGO Precision Industrial Co., Ltd. Manufacturer Address No. 947 Linsen Rd., Wufeng, 41352 Taichung City, Taiwan 1.3 Technical data of EUT Equipment Remote Control Transmitter Model No 8001TX, SP8001TX, 8301TX, 8001AF1TX FCC ID K9L8001TX Power Type Powered by USB DC 5Volt The EUT is a remote transmitter. The operation frequency is 303.8MHz. 1.4 Description of Support Equipment The EUT itself forms a system. No support equipment is required for its normal operation. Page: 6 / 33 Report Number: MLT2102P15001 1.5 Configuration of System Under Test 1.6 Test Procedure All measurements contained in this report were performed according to the techniques described in Measurement procedure ANSI C63.10: 2013 "Measurement of Intentional Radiators." 1.7 General Test Condition The conditions under which the EUT operates were varied to determine their effect on the equipment's emission characteristics. The final configuration of the test system and the mode of operation used during these tests was chosen as that which produced the highest emission levels. However, only those conditions which the EUT was considered likely to encounter in normal use were investigated. The EUT is a automatic activated device and it will follow the 15.231(e) requirement. 1.8 Test environment : Temperature : 24 Degrees Celsius Relative Humidity : 67 % EUT USB Page: 7 / 33 Report Number: MLT2102P15001 2. Conducted Emissions Requirements 2.1. General & Setup : The power line conducted emission measurements were performed in a shielded enclosure. The EUT was assembled on a wooden table which is 80 centimeters high, was placed 40 centimeters from the back wall and at least 1 meter from the sidewall. Power was fed to the EUT from the public utility power grid through a line filter and EMCO Model 3825/2 Line Impedance Stabilization Networks (LISN). The LISN housing, measuring instrumentation case, ground plane, etc., were electrically bonded together at the same RF potential. The Spectrum analyzer was connected to the AC line through an isolation transformer. The 50-ohm output of the LISN was connected to the spectrum analyzer directly. Conducted emission levels were in the CISPR quasi-peak detection mode. The analyzer's 6 dB bandwidth was set to 9 KHz. No post-detector video filter was used. The spectrum was scanned from 150 KHz to 30 MHz. The physical arrangement of the test system and associated cabling was varied (within the scope of arrangements likely to be encountered in actual use) to determine the effect on the unit's emanations in amplitude and frequency. All spurious emission frequencies were observed. The highest emission amplitudes relative to the appropriate limit were measured and have been recorded in paragraph 2.5. 2.2. Test Equipment List : Item Mfr/Brand Instruments Serial No. Model/Type No. Calibrated Date Next Cal. Date 1. R & S EMI Receiver 100085 ESPI 2020/12/23 2021/12/23 2. EMCO LISN 2658 3825/2 2020/12/23 2021/12/23 3. EMCO LISN 2654 3825/2/1 2021/01/13 2022/01/13 Page: 8 / 33 Repo…

Text truncated - open the document above for the full version.

Report Number: MLT2102P15001 Photograph of Conducted Measurement Front View of The Test Configuration Rear View of The Test Configuration Report Number: MLT2102P15001 Photograph of Radiated Measurement (Below 1GHz) Front View of The Test Configuration Rear View of The Test Configuration Report Number: MLT2102P15001 Photograph of Radiated Measurement (Above 1GHz) Front View of The Test Configuration Rear View of The Test Configuration