MES410GPCSmart Card Reader

FCC ID: MES410GPC 1 USER MANUAL This is a copy of the page where the FCC statement is included : Regulatory Information Notice for the USA: FCC Statement Federal Communications Commission (FCC) Radio Frequency Interference Statement (USA Only) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protections against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one of more of the following measures: ! Relocate the radio or television antenna. ! Plug the equipment away from the radio or television. ! Plug the equipment into a different electrical outlet, so that the equipment and the radio or television are on separate electrical circuits. ! Make sure that all your peripheral devices are also FCC Class B certified. ! Make sure you use only shielded cables to connect peripheral devices to your equipment. ! Consult your equipment dealer, or an experienced radio / television technician for help. WARNING: The system verification tests were conducted with GEMPLUS supported peripheral devices. Cables used with this equipment must be properly shielded to comply with the requirements of the FCC. Changes or modifications not expressly approved by GEMPLUS could void the user's authority to operate the equipment. ! Accessories for use with UL Listed Computers having limited power or Class 2 output !

FCC ID: MES410GPC 1 EXTERNAL PHOTOS OF TESTED EUT Ge ne ral vie w Front viewRear view Top viewBottom view

FCC ID: MES410GPC 1 PRODUCT LABELING 1.1 FCC ID Label This is the copy of the label stuck on the product 1.2 Location of label on EUT Label is stuck on the bottom face of the product (see picture). Label will be at that location

FCC ID: MES410GPC 1 INTERNAL PHOTOS OF TESTED EUT 1 – Internal view, Box opened 2 – Internal board, Component side 3 – Internal board, Component side, connector removed FCC ID: MES410GPC 4 – Internal board, Foil side 5 – Box, board re moved

FCC ID: MES410GPC 1 GENERAL INFORMATION 1.1 Product description The GemPC410 device is a smart card reader connected to a Personal Computer. Smart cards which can be used with the GemPC410 reader are: reads from or writes to ISO7816-1/2/3/4 memory and micro processor smart cards. The smart card is introduced in the GemPC410 reader, and the Personal Computer manages applications; Typical applications are: - Computer access control - Electronic commerce - Home banking facilities - E-purse facilities - Electronic smart card personalization - Development of smart card application software - Others... The GemPC410 reader is connected to the RS232 serial port for communication with the Personal Computer and is powered from keyboard's port,. The GemPC410 is a product developed by the Gemplus company; Its part number is RPF15888A0 and its ex- name was GCR410p For more information, see product's data sheet at section 1.6. 1.2 Related Submittal(s) / Grant(s) All host equipment used in the test configuration are FCC granted, when relevant. 1.3 Tested System Details The FCC IDs for all equipment, plus description of all cables used in the tested system (including inserted cards, w hich have grants) are : Tra de Ma rk – Mo de l Numbe r (Se rial numbe r) FCC IDDe scri ptio nCa ble de scri ptio n GemPC410* (sn: FR62365527) MES410IGPCSmart card readerShielded cable attached to product Gemplus MPC0S64K-3DESnoneSmart cardnone HEWLETT PACKARD Vectra 515 series D4136A (sn: FR62365527) B94VECTRA500TPersonal computerAll data cables are shielded Power cable unshielded HEWLETT PACKARD D2846A (sn JP74001000) Doc. Of Conf.21" color monitorShielded video cable HEWLETT PACKARD C4734-60101 (sn: M97060565) GYUR38SKKeyboardShielded cable HEWLETT PACKARD C3751B (sn: LZA61209812) DZL210582MouseShielded cable HEWLETT PACKARD C2106A (sn: 3110S58792) Doc. Of ConfSerial printerHP 24542G shielded serial cable HEWLETT PACKARD C6410A (sn: MY9761915T) Doc. Of Conf.Parallel printerHP 24542D shielded parallel cable *Equipment Under Test 1.4 Test Methodology Both conducted and radiated testing were performed according to the procedures in ANSI C63.4-1992, CISPR22-1993/A1:1995 and EN55022:1994/A1:1995. Radiated testing was performed at an antenna to EUT distance of 10 meters. During testing, all equipment’s and cables were moved relative to each other in order to identify the worst case set-up. FCC ID: MES410GPC 1.5 Test facility Tests have been performed on November 8th, 1999. The test facility used to collect the radiated and conducted data is the SMEE Actions Mesures facility, located ZI des Blanchisseries, 38500 VOIRON, France. This test facility has been fully described in a report and accepted by FCC as compliant with the radiated and AC line conducted test site criteria in ANSI C63.4-1992 in a letter dated August 04, 1999 (registration number 94821). This test facility has also been accredited by COFRAC (French accreditation authority for European union test lab accreditation organization), accreditation number 1-0844 as compliant with test site criteria and competence in EN55022/CISPR22 norms for 89/336/EEC European EMC Directive application. All pertinent data for this test facility remains unchanged. 1.6 Data sheet of the product A Universal Smart Card Reader The GemPC410 (ex GCR410p) was certified by Microsoft's WHQL in January 99 A highly accessible, highly convenient solution. This compact card reader, designed to plug into a PC environment, is the ultimate smart card peripheral for a PC. It is also very simple to use and install. The user needs no technical knowledge. If you need electronic commerce, home banking or e-purse facilities, secure computer access or any of a multitude of other applications, the GemPC410 (ex GCR410p) is the smartest answer. For the first time, a solution is available that offers impressive possibilities at an exceptional price. Small is beautiful At a mere 86 x 85 x 26 mm, the GemPC410 (ex GCR410p) will handle the card interface, while your computer supports and manages the applications. Compatible with all major computers and operating systems, the GemPC410 (ex GCR410p) is powered from your computer’s keyboard port, free of the constraints associated with other power-source options. It will open up many possibilities, including: • computer-access control, • electronic commerce, • home banking facilities, • e-purse facilities, • electronic smart-card personalization, • development of smart-card application software, • lots of other interesting or entertaining things. • Years of Gemplus technological experience, now available to all The GemPC410 (ex GCR410p) is based on Gemplus’s GemCore ® hardware and firmware, which means it can handle all types of ISO7816- compatible smart cards without compatibility problems. It is user-friendly, and operating or using it requires no technical expertise. The GemPC410 (ex GCR410p) will happily blend with all main environments (DOS, Windows ®* 3.x, Windows ® 95, Windows ® NT, OS/2 ® , etc.), all types of card, and most makes of computer. It will readily adapt to new smart-card services, as they become available FCC ID: MES410GPC GemPC410 (ex GCR410p) Features and Application Standards Feature Description Smart-card interface • reads from and writes to all ISO7816-1/2/3/4 memory and microprocessor smart cards (T=0, T=1) • supports 3V and 5V cards Communication • programmable from 9,600 baud to 115,200 baud with the smart card • up to 38,400 baud for communication with PC Power consumption average of 20 mA in operational mode Interface modes • Serial communication with the PC through RS232 connection • TLP224 and GBP (Gemplus Block Protocol) Power supply 5V maximum Electro-magnetic standards • Europe: 89/336/CEE guideline • USA: FCC part 15 Security levels • Europe: EN60950 • USA: UL1950 • Canada: CSA950 The cable supplied with the GemPC410 (ex GCR410p) allows the user to connect both the keyboard and the reader to the same port.

FCC ID: MES410GPC 1 TEST REPORT 1.1 System test configuration 1.1.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it). A typical smart card was introduced in the GemPC410 reader, which was itself connected to a personal computer. It has been tested with a Hewlett Packard Vectra 515series D4136A Personal computer. Each ports of the Personal Computer were loaded with a typical peripheral device. 1.1.2 EUT Exercise software The EUT exercise program (testcem 2.exe running under DOS) used during radiated and conducted testing was designed to exercise the GemPC410 reader in a manner similar to a typical use (reading the smart card in loop) 1.1.3 Special accessories The cable used to connect the GemPC410 reader to the keyboard and RS232 ports of the Personal Computer is shielded and attached to the product. It is connected to Com 1; Serial plotter to Com2. The smart card used in the GemPC410 is a GemPlus MPC0S64K-3DES. As shown in Figure 3.1, all interfaces cables used for compliance testing are shielded as normally supplied. All these cables are normally recommended to be used with the Personal Computer. 1.1.4 Equipment modifications No equipment modification has been necessary during testing to achieve compliance to Class B levels. The unit tested was representative to a production unit. 1.1.5 Configuration of tested system HP C2106A Printer HP C6410A Printer Monitor D2846A PC Vectra 515 Series Mouse Keyboard GemPC410 Smart card FCC ID: MES410GPC 1.2 Conducted emission data 1.2.1 Test procedure The product has been tested according to ANSI C63.4-1992, CISPR22-1993/A1:1995 and EN55022:1994/A1:1995. The product has been tested with 120V / 60Hz power line voltage and compared to the CISPR22 Class B limits. Measurement bandwidth was 9KHz from 150 KHz to 30 MHz. Measurement was initially made with an HP-8591EM Spectrum Analyzer in peak mode. This was followed by a Quasi-Peak, i.e. CISPR measurement with the Rohde & Schwarz ESH3 receiver for any strong signal. If the average limit is met when using a Quasi-Peak detector, the EUT shall be deemed to meet both limits and measurement with the average detector is unnecessary. The Peak data are show n on the following plots. Quasi-Peak and Average measurements are detailed in a table with frequencies and levels measured. Interconnecting cables and equipment's were moved to position that maximized emission. A summary of the worst case emissions found in all test configurations and modes is shown on the following page. Test equipment : HP 8591EM Spectrum Analyzer Rhode & Schwarz ESH3 Receiver EMCO 3810/2SH LISN N°1 TELEMETER NNB-2/16L LISN N°2 FCC ID: MES410GPC 1.2.2 Neutral conducted emission data on GemPC410 Freq.PeakQ-PeakQP limitQP deltaAverageAVG LimitAVG Delta Num. [MHz][dBμV][dBμV][dBμV][dBμV][dBμV][dBμV][dBμV] 10,15053,0848,1764,00-15,8346,1954,00-7,81 20,23050,4348,6762,00-13,3346,6052,00-5,40 30,30045,6643,3060,00-16,740,5650,00-9,44 40,34046,4145,7258,00-12,2843,4848,00-4,52 50,38031,6923,6658,00-34,3417,2548,00-30,75 60,43034,1732,4356,00-23,5729,6746,00-16,33 70,45035,0132,3156,00-23,6925,9446,00-20,06 815,6035,3725,9860,00-34,0224,7350,00-25,27 923,3641,0037,6160,00-22,3931,7450,00-18,26 FCC ID: MES410GPC 1.2.3 Line conducted emission data on GemPC410 Freq.PeakQ-PeakQP limitQP deltaAverageAVG LimitAVG Delta Num. [MHz][dBμV][dBμV][dBμV][dBμV][dBμV][dBμV][dBμV] 10,15049,7341,1164,00-22,8923,2454,00-30,76 20,18049,5141,9564,00-22,0527,8754,00-26,13 30,19048,2039,9164,00-24,0919,6054,00-34,4 40,22046,8639,5862,00-22,4234,1152,00-17,89 50,25044,8337,0160,00-22,9926,8550,00-23,15 60,28044,0836,0860,00-23,9225,5550,00-24,45 70,30043,6340,5760,00-19,4336,7350,00-13,27 80,34044,4343,7458,00-14,2641,5348,00-6,47 90,38032,9930,8058,00-27,227,2648,00-20,74 100,43034,9433,0456,00-22,9630,5046,00-15,5 110,46035,7734,2156,00-21,7931,2746,00-14,73 120,53034,0031,2356,00-24,7723,7546,00-22,25 1315,6034,9430,8460,00-29,1619,4850,00-30,52 1423,3542,3138,8660,00-21,1430,1350,00-19,87 FCC ID: MES410GPC 1.3 RADIATED EMISSION DATA 1.3.1 Test Procedure The product has been tested according to ANSI C63.4-1992, CISPR 22-1993/A1:1995 and EN55022:1994/A1:1995. The product has been tested with 230V / 50Hz power line voltage, at a distance of 10 meters from the antenna and compared to the CISPR 22 Class B limits. Measurement bandwidth was 120 KHz from 30 MHz to 1 GHz. Antenna height search was performed from 1m to 4m for both horizontal and vertical polarization. Continuous linear turntable azimuth search was performed with 360 degrees range. Interconnecting cables and equipment's were moved to position that maximized emission. A summary of the worst case emissions found in all test configurations and modes is shown on the following page. Test Equipme nt: HP-8574A E.M.I Receiver (HP-8568B Analyzer + HP-85650 Quasi-Peak adapter + HP-85685A RF Preselector). EMCO 3104C Biconical Antenna & EMCO 3146 Log Periodic Antenna EMCO-1050, 6 meters height antenna mast & EMCO-1060, 3 meters diameter Turntable. 1.3.2 Radiated emission data Final result 30-1000 MHz Graph example - 30-1000MHz Frequency (MHz) QPeak Lmt (dBμV/m) QPeak (dBμV/m) QPeak-Lmt (dB) Angle (deg) PolHgt (c m) Tot Cor r (dB) 42.953020.8-9.291V11511.5 47.993026.1-3.9268V10211.8 85.023023.3-6.7257H39410.2 96.004039.2-0.8(1)140V21913.8 * 99.644035.7-4.3310V21315.2 * 133.023025.8-4.249V10915.3 186.163023.3-6.765V10219.4 199.233023.7-6.331V15020.2 224.113023.9-6.1257H34714.3 249.043729.0-8.0339V10215.0 507.583730.0-7.0196H34522.4 647.473731.7-5.3297H27425.0 697.273731.9-5.1140V21927.1 (1): EUT - Ambiant noise = 3dB *: due to ambiant noise, measure has been performed at 3 meters. FCC ID: MES410GPC 1.3.3 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain (if any) from the measured reading. The basic equation with a sample calculation is as follow : FS = RA + AF + CF – AG Wher…

Text truncated - open the document above for the full version.

FCC ID: MES410GPC 1 CONDUCTED AND RADIATED MEASUREMENT PHOTO 1.1 Conducted emission Front viewRear view 1.2 Radiated emission Front ViewRear view