MES410IGCRIBM 410p SMART CARD READER

FCC ID: MES410IGCR 1 USER MANUAL This is a copy of the manual page where the FCC statement is included : Regulatory Information Notice for the USA: FCC Statement Federal Communications Commission (FCC) Radio Frequency Interference Statement (USA Only) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protections against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one of more of the following measures:
Relocate the radio or television antenna.
Plug the equipment away from the radio or television.
Plug the equipment into a different electrical outlet, so that the equipment and the radio or television are on separate electrical circuits.
Make sure that all your peripheral devices are also FCC Class B certified.
Make sure you use only shielded cables to connect peripheral devices to your equipment.
Consult your equipment dealer, or an experienced radio / television technician for help. WARNING: The system verification tests were conducted with GEMPLUS supported peripheral devices. Cables used with this equipment must be properly shielded to comply with the requirements of the FCC. Changes or modifications not expressly approved by GEMPLUS could void the user's authority to operate the equipment.

FCC ID: MES410IGCR 1 BLOCK DIAGRAM(S) OF EQUIPMENT 1.1 Clock list of IBM 410p product Frequency range in MHz Frequency tolerance Emission designatot Microprocessor model number 14.74 +/- 0.7% Ceramic Resonator TEMIC TSC71RCX2-24IB 14.74 MHz CPU Interface RS 232 Interface card IBM-410p Diagram 5V from PC keyboard connector

FCC ID: MES410IGCR 1 COVER LETTER Gemplus – IBM 410p FCC ID: MES410IGCR November 17, 1999 This report concerns : Original Grant ___X____Class II change __________ Class B certification ___X____*Class A verification _______Class I change _______ Equipment type : Computing Device Peripheral (Equipment code : JBP) Request issue of grant : ___Immediately upon completion of review ___Defer grant per 47 CFR 0.457(d)(1)(ii) until ____ date _____. Company Name agrees to notify the Commission by _____date_____ of the intended date of announcement of the product so that the grant can be issued on that date. Confidentiality of grant : ___Applicant requests the existence of this grant to be kept confidential until ____date____. The announcement of this product before this date via freedom of information would be detrimental to Company Name, and therefore must be considered a business secret. Public announcement of this product will not be made prior to this date. (Max. 60 days after grant issued). Limits used : (check one) CISPR 22 _______X___________ Part 15 __________________ Measurement procedure used is ANSI C63.4-1992 unless another is specified. Other test procedure : ____________________________________________________ Application for verificationApplicant for this device Prepared by : Frank HAMELIN SMEE Actions Mesures ZI des Blanchisseries 38500 VOIRON – France Ph. : 33 4 76 65 76 50 Fax : 33 4 76 66 18 30 e-mail : [email protected] Pierre André COLLET Gemplus Voie Antiope Athelia III 13705 LA CIOTAT CEDEX 8 – France Ph. : 33 4 42 36 62 60 Fax : 33 4 42 36 62 98 e-mail: [email protected] *Not to be filed with Equipment Authorization Branch of FCC unless requested Report format prepared by the Information Technology Industry Council (ITI) ESC-5 and reviewed by FCC staff in 1994

FCC ID: MES410IGCR 1 EXTERNAL PHOTOS OF TESTED EUT The following photos are attached : 1 - Front view 2 - Rear view 3 - Top view FRONT VIEWREAR VIEW TOP VIEW

FCC ID: MES410IGCR 1 PRODUCT LABELING 1.1 FCC ID Label This is the copy of the label stuck on the product This is the copy of the Class B label stuck on the product 21mm+0/-0,2 12mm+0/-0,2 21mm+0/-0,2 12mm +0/-0,2 FCC ID: MES410IGCR 1.2 Location of label on EUT Labels are stuck on the rear face of the product. Location of the FCC ID label

FCC ID: MES 410IGCR 1 INTERNAL PHOTOS OF TESTED EUT The following photos are attached : 1 – Internal view, component side 2 – Internal view, Bottom side 3 – Internal view Bottom side, cover removed 1 – Internal view, Component side 2 – Internal view, Bottom side 3 – Internal view, Bottom side, cover removed

FCC ID: MES410IGCR 1 GENERAL INFORMATION 1.1 Product description The IBM410p device is a smart card reader connected to a Personal Computer. Smart cards which can be used with the IBM 410p reader are: reads from or writes to ISO7816-1/2/3/4 memory and micro processor smart cards. The smart card is introduced in the IBM410p reader, and the Personal Computer manages applications; Typical applications are: - Computer access control - Electronic commerce - Home banking facilities - E-purse facilities - Electronic smart card personalization - Development of smart card application software - Others... The IBM 410p reader is connected to the RS232 serial port for communication with the Personal Computer and is powered from keyboard's port,. The IBM 410p is a product developed by the Gemplus company; Its name in Gemplus company, is: GemPC410. (ex GCR410p). That's why in data's results could appear the GCR410p reference. For more informations, see product's data sheet at section 1.6. 1.2 Related Submittal(s) / Grant(s) All host equipment used in the test configuration are FCC granted, when relevant. 1.3 Tested System Details The FCC IDs for all equipment, plus description of all cables used in the tested system (including inserted cards, which have grants) are : Trade Mark – Model Number (Serial number) FCC IDDescriptionCable description IBM 410p* (sn: 99240103) MES410IGCRSmart card readerShielded cable attach to product HEWLETT PACKARD Vectra 515 series D4136A (sn: FR62365527) B94VECTRA500TPersonal computerAll data cables are shielded Power cable unshielded HP D2846A (sn JP74001000) Doc. Of Conf.21" color monitorShielded video cable IBM KB7953 (sn: 0010491) Doc. Of Conf.KeyboardCable shielded HP C3751B (sn: LZA62831217) DZL211029MouseCable shielded HP 7440A (sn: 2807L77281) BSD4TE7475ASerial plotterHP 24542G shielded serial cable HP C6410A (sn: MY9761915T) Doc. Of Conf.Parallel printerHP 24542D shielded parallel cable *Equipment Under Test 1.4 Test Methodology Both conducted and radiated testing were performed according to the procedures in ANSI C63.4-1992, CISPR22-1993/A1:1995 and EN55022:1994/A1:1995. Radiated testing was performed at an antenna to EUT distance of 10 meters. During testing, all equipment’s and cables were moved relative to each other in order to identify the worst case set-up. FCC ID: MES410IGCR 1.5 Test facility Tests have been performed on November 8th, 1999. The test facility used to collect the radiated and conducted data is the SMEE Actions Mesures facility, located ZI des Blanchisseries, 38500 VOIRON, France. This test facility has been fully described in a report and accepted by FCC as compliant with the radiated and AC line conducted test site criteria in ANSI C63.4-1992 in a letter dated August 04, 1999 (registration number 94821). This test facility has also been accredited by COFRAC (French accreditation authority for European union test lab accreditation organization), accreditation number 1-0844 as compliant with test site criteria and competence in EN55022/CISPR22 norms for 89/336/EEC European EMC Directive application. All pertinent data for this test facility remains unchanged. 1.6 Data sheet of the product A Universal Smart Card Reader The GemPC410 (ex GCR410p) was certified by Microsoft's WHQL in January 99 A highly accessible, highly convenient solution. This compact card reader, designed to plug into a PC environment, is the ultimate smart card peripheral for a PC. It is also very simple to use and install. The user needs no technical knowledge. If you need electronic commerce, home banking or e-purse facilities, secure computer access or any of a multitude of other applications, the GemPC410 (ex GCR410p) is the smartest answer. For the first time, a solution is available that offers impressive possibilities at an exceptional price. Small is beautiful At a mere 86 x 85 x 26 mm, the GemPC410 (ex GCR410p) will handle the card interface, while your computer supports and manages the applications. Compatible with all major computers and operating systems, the GemPC410 (ex GCR410p) is powered from your computer’s keyboard port, free of the constraints associated with other power-source options. It will open up many possibilities, including: • computer-access control, • electronic commerce, • home banking facilities, • e-purse facilities, • electronic smart-card personalization, • development of smart-card application software, • lots of other interesting or entertaining things. • Years of Gemplus technological experience, now available to all The GemPC410 (ex GCR410p) is based on Gemplus’s GemCore ® hardware and firmware, which means it can handle all types of ISO7816- compatible smart cards without compatibility problems. It is user-friendly, and operating or using it requires no technical expertise. The GemPC410 (ex GCR410p) will happily blend with all main environments (DOS, Windows ®* 3.x, Windows ® 95, Windows ® NT, OS/2 ® , etc.), all types of card, and most makes of computer. It will readily adapt to new smart-card services, as they become available FCC ID: MES410IGCR GCR410p Features and Application Standards Feature Description Smart-card interface • reads from and writes to all ISO7816-1/2/3/4 memory and microprocessor smart cards (T=0, T=1) • supports 3V and 5V cards Communication • programmable from 9,600 baud to 115,200 baud with the smart card • up to 38,400 baud for communication with PC Power consumption average of 20 mA in operational mode Interface modes • Serial communication with the PC through RS232 connection • TLP224 and GBP (Gemplus Block Protocol) Power supply 5V maximum Electro-magnetic standards • Europe: 89/336/CEE guideline • USA: FCC part 15 Security levels • Europe: EN60950 • USA: UL1950 • Canada: CSA950 The cable supplied with the GemPC410 (ex GCR410p) allows the user to connect both the keyboard and the reader to the same port.

FCC ID: MES410IGCR 1 TEST REPORT 1.1 System test configuration 1.1.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it). A typical smart card was introduced in the IBM 410p reader, which was itself connected to a personal computer It has been tested with a Hewlett Packard Vectra 515series D4136A Personal computer. Each ports of the Personal Computer were loaded with a typical peripheral device. 1.1.2 EUT Exercise software The EUT exercise program (testcem 1.exe running under DOS) used during radiated and conducted testing was designed to exercise the IBM 410p reader in a manner similar to a typical use (reading the smart card in loop) 1.1.3 Special accessories The cable used to connect the IBM 410p reader to the keyboard and RS232 ports of the Personal Computer is shielded and attached to the product. It is connected to Com 1; Serial plotter to Com2. As shown in Figure 3.1, all interfaces cables used for compliance testing are shielded as normally supplied. All these cables are normally recommended to be used with the Personal Computer. 1.1.4 Equipment modifications No equipment modification has been necessary during testing to achieve compliance to Class B levels. The unit tested was a production unit. 1.1.5 Configuration of tested system. HP C6410A Printer HP7440A plotter Monitor D2846A PC Vectra 515 Series Mouse Keyboard IBM 410p Smart card FCC ID: MES410IGCR 1.2 Conducted emission data 1.2.1 Test procedure The product has been tested according to ANSI C63.4-1992, CISPR22-1993/A1:1995 and EN55022:1994/A1:1995. The product has been tested with 120V / 60Hz power line voltage and compared to the CISPR22 Class B limits. Measurement bandwidth was 9KHz from 150 KHz to 30 MHz. Measurement was initially made with an HP-8591EM Spectrum Analyzer in peak mode. This was followed by a Quasi-Peak, i.e. CISPR measurement with the Rohde & Schwarz ESH3 receiver for any strong signal. If the average limit is met when using a Quasi-Peak detector, the EUT shall be deemed to meet both limits and measurement with the average detector is unnecessary. The Peak data are shown on the following plots. Quasi-Peak and Average measurements are detailed in a table with frequencies and levels measured. Interconnecting cables and equipment's were moved to position that maximized emission. A summary of the worst case emissions found in all test configurations and modes is shown on the following page. Test equipment : HP 8591EM Spectrum Analyzer Rhode & Schwarz ESH3 Receiver EMCO 3810/2SH LISN N°1 TELEMETER NNB-2/16L LISN N°2 FCC ID: MES410IGCR 1.2.2 Neutral conducted emission data on IBM410p Freq.PeakQ-PeakQP limit QP delta AverageAVG Limit AVG Delta Num. [MHz][dBμV][dBμV][dBμV] [dBμV] [dBμV][dBμV] [dBμV] 10.15049.8741.3564-22.6533.2854.00-20.72 20.17048.8440.5564-23.4532.9854.00-21.02 30.22045.9537.1562-24.8524.2452.00-27.76 40.25044.7037.2660-22.7433.4450.00-16.56 50.31043.6941.6858-16.3239.1048.00-8.9 60.35044.0643.2858-14.7241.0748.00-6.93 FCC ID: MES410IGCR 1.2.3 Line conducted emission data on IBM410p Freq.PeakQ-PeakQP limit QP delta AverageAVG Limit AVG Delta Num. [MHz][dBμV][dBμV][dBμV] [dBμV] [dBμV][dBμV] [dBμV] 10.16052.1748.5064-15.546.9754.00-7.03 20.23050.1046.3562-15.6543.4252.00-8.58 30.25046.5441.996018.0139.7250.00-10.28 40.28043.8235.7960-24.2116.9050.00-33.1 50.30045.6043.4160-16.5940.9550.00-9.05 60.34046.2345.4058-12.643.1448.00-4.86 FCC ID: MES410IGCR 1.3 RADIATED EMISSION DATA 1.3.1 Test Procedure The product has been tested according to ANSI C63.4-1992, CISPR 22-1993/A1:1995 and EN55022:1994/A1:1995. The product has been tested with 230V / 50Hz power line voltage, at a distance of 10 meters from the antenna and compared to the CISPR 22 Class B limits. Measurement bandwidth was 120 KHz from 30 MHz to 1 GHz. Antenna height search was performed from 1m to 4m for both horizontal and vertical polarization. Continuous linear turntable azimuth search was performed with 360 degrees range. Interconnecting cables and equipment's were moved to position that maximized emission. A summary of the worst case emissions found in all test configurations and modes is shown on the following page. Test Equipment: HP-8574A E.M.I Receiver (HP-8568B Analyzer + HP-85650 Quasi-Peak adapter + HP-85685A RF Preselector). EMCO 3104C Biconical Antenna & EMCO 3146 Log Periodic Antenna EMCO-1050, 6 meters height antenna mast & EMCO-1060, 3 meters diameter Turntable. 1.3.2 Radiated emission data Final result 30-1000 MHz Graph example - 30-1000MHz Frequency (MHz) QPeak Lmt (dBμV/m) QPeak (dBμV/m) QPeak-Lmt (dB) Angle (deg) PolHgt (cm) Tot Corr (dB) 44.2230.0028.6-1.4171V10311.7 57.2930.0022.6-7.4242H37711.6 139.9830.0024.1-5.982V10315 147.3630.0027.4-2.6255H36715.5 149.4230.0021.6-8.430V10715.6 209.9730.0019.9-10.136V10414.0 217.3330.0023.6-6.460V10414.2 235.7537.0021.6-15.5297H33814.6 996.0337.0031.6-5.4256V10230.5 FCC ID: MES410IGCR 1.3.3 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain (if any) from the measured reading. The basic equation with a sample calculation is as follow : FS = RA + AF + CF – AG WhereFS = Field Strength RA = Receiver Amplitude AF = Antenna Factor CF = Cable Factor AG = Amplifier Gain Assume a receiver reading of 52.5dBμV is obtained. The antenna factor of 7.4 and a cable factor of 1.1 is added. The amplifier gain of 29dB is subtracted, giving a field strength of 32 dBμV/m. FS = 52.5 + 7.4 + 1.1 – 29 = 32 dBμV/m The 32 dBμV/m value can be mathematically converted to its corresponding level in μV/m. Level in μV/m = Common Antilogarithm [(32dBμV/m)/20] = 39.8 μV/m.

FCC ID: MES410IGCR 1 CONDUCTED AND RADIATED MEASUREMENT PHOTO 1.1 Conducted emission Front viewRear view 1.2 Radiated emission Front ViewRear view