PVH1953WLAN & Bluetooth Module

- -Page of 121 Document Information Title Subtitle Document type Document number Revision and date Document status u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or any part thereof without the express permission of u-blox is strictly prohibited. The information contained herein is provided “as is” and u-blox assumes no liability for the use of the information. No warranty, either express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose of the information. This document may be revised by u-blox at any time. For most recent documents, visit . Copyright © 2014, u-blox AG.www.u-blox.com u-blox® is a registered trademark of u-blox Holding AG in the EU and other countries. ARM® is the registered trademark of ARM Limited in the EU and other countries. - -Page of 221 Contents 1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1Document Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3Product Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2Electrical Interface and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1Primary Side Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2Secondary Side Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.3J4-20 RF-port solder land . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.4Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.4.1Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.4.2I/O DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.4.3LPO Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5.1Wireless LAN and SDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5.2Bluetooth UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.6Environmental Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3Antenna Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2External Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.2.1Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4Mounting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.1Module Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.2PCB Solder Lands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2.1Host Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2.2Mounting Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1CE compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1.1Equipment classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1.2Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.2IC and FCC compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.2.1IC compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.2.2Conformité aux normes d’IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.2.3FCC statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.3Compliance with RoHS Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 - -Page of 321 6Guidelines for Efficient and Safe Use . . . . . . . . . . . …

Text truncated - open the document above for the full version.

locate, communicate, accelerate Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Certification Application Model: ODIN(W161 FCC ID: PVH1953 Request for Part 15 Limited Modular Transmitter Approval To whom it may concern: We, u(blox Malmö AB, hereby requests for a limited modular transmitter approval of our OEM(WLAN/Bluetooth module ODIN(W161. Please observe that integration of the module is to be made by the grantee himself thus limited to own use only The equipment is described as follows: Brand name: u(blox Model: ODIN(W161 FCC ID: PVH1953 In 47 C.F.R. §15.212 there are eight numbered requirements a single modular transmitter must meet to obtain a modular transmitter approval. Our OEM(WLAN/Bluetooth module ODIN(W161 complies with 7 (seven) of these requirements. Requirement number 4 is not fulfilled. 1. The modular transmitter must have its own RF shielding The module ODIN(W161 has its RF(parts covered by a shield box that is soldered on to the module ground plane. 2. The modular transmitter must have buffered modulation/data inputs The module ODIN(W161 does not have modulation inputs. The electrical connection consists of power supply, UART, SDIO, SPI and digital(I/O. The interface signals (UART, SDIO, SPI and digital(I/O) are internally buffered by the module SoC (System on Chip) and cannot affect the modulation. Detailed instruction on how to connect these interface signals are given in the product Users Guide. 3. The modular transmitter must have its own power supply regulation The WLAN/Bluetooth (module ODIN(W161 has its own voltage regulators. In case the supply voltage changes, the internal voltages will be kept unchanged. 4. The modular transmitter must comply with the antenna requirements of Section 15.203, 15.204(b) and 15.204(c) The module ODIN(W161 does not comply with this requirement as it has neither an own antenna nor a unique antenna connector mounted on the module. The RF port is available via a solder land and the reference design connects its antenna port to this solder land. 5. The modular transmitter must be tested in a stand.alone configuration The ODIN(W161 was tested on a reference design in a stand(alone configuration. Registered office: u.blox Malmö AB Östra Varvsgatan 4, 5tr 211 75 Malmö Sweden Registered number: 556589(0851 Phone +46 40 630 71 00 Fax +46 40 237 137 info@u(blox.com support@u(blox.com 6. The modular transmitter must be labelled with its own FCC ID number The module ODIN(W161 is marked with its own FCC ID number. The FCC ID number is printed on a label that is affixed on the shield cover. For systems using the module where the original FCC ID marking not will be visible when the module is installed instructions will be provided to the OEM integrator how the end product must be label. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The WLAN/Bluetooth(module ODIN(W161 is compliant with all applicable FCC rules. Detail instructions are given in the product Users Guide. 8. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The RF Module complies with the RF exposure limits when integrated into host devices categorized as mobile and/or fixed Refer to documents: • Calculation rf(exposure F145298E1.pdf • Calculation rf(exposure F145298E2.pdf • Calculation rf(exposure F145298E3.pdf • Calculation rf(exposure F145298E4.pdf • Calculation rf(exposure F145298E5.pdf Thank you for your attention in this matter. _______________________________ Mats Andersson Job Title and Dept.: CTO u(blox Malmö AB

locate, communicate, accelerate Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Certification Application Model: ODIN(W161 FCC ID: PVH1953 IC: 5325A(1953 Request for Long/Shortterm Confidentiality To whom it may concern: Pursuant to sections 0.457(d) and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, we hereby requests long(term confidential treatment of information accompanying this application as outlined below: Schematics Software security and software configuration description Block Diagram Operational Description In addition we hereby request the following exhibits contained in this application to be temporarily (short(term confidentiality) withheld from the public disclosure for an initial period of days until: not applicable External Photos Test Setup Photos Internal Photos User’s Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to rule 0.457(d), disclosure of this application and all accompanying documentation will not be made before the date of the GRANT for this application. Thank you for your attention in this matter. Applicant’s Company: u(blox Malmö AB address: Östra Varvsgatan 4 5tr, SE(211 75 Malmoe, Sweden _______________________________ Mats Andersson Job Title and Dept.: CTO u(blox Malmö AB Registered office: ublox Malmö AB Östra Varvsgatan 4, 5tr 211 75 Malmö Sweden Registered number: 556589(0851 Phone +46 40 630 71 00 Fax +46 40 237 137 info@u(blox.com support@u(blox.com

locate, communicate, accelerate Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Certification Application Model: ODIN(W161 FCC ID: PVH1953 IC: 5325A(1953 Mode Function Declaration To whom it may concern: We, the undersigned, declare that the device described as follows: Brand name: u(blox Model: ODIN(W161 IC: 5325A(1953 FCC ID: PVH1953 1. Is acting as slave and Ad Hoc function is supported within the following frequency bands: (limited to operate on US/Canada frequencies only) • channels 1 – 11 (2412 – 2462 MHz) 802.11b/g/n/20 MHz BW • channels 36 – 48 (5180 – 5240 MHz) 802.11a/n/20 MHz BW 2. Does not have Ad Hoc function on channels within the frequency bands: • channels 12 – 13 (2467 – 2472 MHz) 802.11b/g/n/20 MHz BW • channels 52 – 64 (5260 – 5320 MHz) 802.11a/n/20 MHz BW • channels 100 – 140 (5500 – 5700 MHz) 802.11a/n/20 MHz BW • channels 149 – 165 (5745 – 5825 MHz) 802.11a/n/20 MHz BW 3. Does not initiate transmission within the frequency band 5600 – 5650 MHz. The module is configured to function under the definition of a client in 47 CFR §15.202 As a DFS client without radar detection using passive scan ODIN(W161 is not able to select channel or initiate a network 4. Is a client without DFS detection capability 5. Is not able to operate on non( US/Canadian frequencies. Country code selection will be disabled for this device 6. In non(associated mode, that software and associated drives will not initiate any transmission on DFS frequencies. This includes transmissions for beacon ad(hoc peer(to(peer modes (KDB 905462 D03) Registered office: ublox Malmö AB Östra Varvsgatan 4, 5tr 211 75 Malmö Sweden Registered number: 556589(0851 Phone +46 40 630 71 00 Fax +46 40 237 137 info@u(blox.com support@u(blox.com Table 1 Active/Passive scanning, Adhoc mode/Access point capability of ODINW161 Frequency band [MHz] Active scanning (the device can transmit a probe) Passive scanning (the device is listen only with no probe) Ad(hoc mode capability Access point capability 2412 – 2462
( Yes,  ( No
( Yes,  ( No
( Yes,  ( No
( Yes,  ( No 2467 – 2472  ( Yes,
( No
( Yes,  ( No  ( Yes,
( No  ( Yes,
( No 5180 – 5240
( Yes,  ( No
( Yes,  ( No
( Yes,  ( No
( Yes,  ( No 5280 – 5320  ( Yes,
( No
( Yes,  ( No  ( Yes,
( No  ( Yes,
( No 5500 – 5700  ( Yes,
( No
( Yes,  ( No  ( Yes,
( No  ( Yes,
( No 5745 – 5825  ( Yes,
( No
( Yes,  ( No  ( Yes,
( No  ( Yes,
( No Please contact the one signed below or the authorized agent for this filing. Thank you. Applicant’s Company: u(blox Malmö AB Address: Östra Varvsgatan 4 5tr, SE(211 75 Malmoe, Sweden _______________________________ Mats Andersson Job Title and Dept.: CTO u(blox Malmö AB Tel: +46 40 630 71 00 Fax: +46 40 237 137 Email: mats.andersson@u(blox.com

ANNEX B: EXTERNAL PHOTOGRAPHS Test engineer: Wolfgang KASALOWSKYTest Report No.: F145298E1 Date of issue: 08 July 2015Order No.:14-115298page 1 of 2 145298_05.jpg: Carrier Board wit EUT – Top View 145298_05.jpg: Carrier Board wit EUT – Top View (detail) ANNEX B: EXTERNAL PHOTOGRAPHS Test engineer: Wolfgang KASALOWSKYTest Report No.: F145298E1 Date of issue: 08 July 2015Order No.:14-115298page 2 of 2 145298_06.jpg: Carrier Board – Bottom View 145298_07.JPG: Carrier Board – Connectors

locate, communicate, accelerate RE: Certification Application Model: ODINW161 FCC ID: PVH1953 IC: 5325A1953 FCC/IC identifier marking for OEMWLAN/Bluetooth module ODINW161 The FCC/IC identifier marking is a label affixed on the shield cover. Figure1 3Dview of ODINW161 with FCC/IC identifier label Figure2 ODINW161 FCC/IC identifier label Registered office: ublox Malmö AB Östra Varvsgatan 4, 5tr 211 75 Malmö Sweden Registered number: 5565890851 Phone +46 40 630 71 00 Fax +46 40 237 137 info@ublox.com support@ublox.com Figure3 Picture of secondary side An auxiliary label will be provided for systems using the module where the original marking will not be visible when the module is installed. Instructions on how to attach the auxiliary label in compliance with the modular approval guidelines developed by the FCC will be provided. The instructions will call attention to place the auxiliary label on an exterior surface of the device such that it will be visible upon inspection. The auxiliary label will have at least the information shown in the figure below This device contains FCC ID:PVH1953 IC:5325A-1953

ANNEX C: INTERNAL PHOTOGRAPHS Examiner:Wolfgang KASALOWSKYTest Report No.: F145298E1 Date of issue: 08 July 2015Order No.:14-115298page 1 of 3 145298_08.JPG: EUT - top view, with shielding 145298_09.JPG: EUT - top view, shielding removed ANNEX C: INTERNAL PHOTOGRAPHS Examiner:Wolfgang KASALOWSKYTest Report No.: F145298E1 Date of issue: 08 July 2015Order No.:14-115298page 2 of 3 145298_10.JPG: EUT – bottom view ANNEX C: INTERNAL PHOTOGRAPHS Examiner:Wolfgang KASALOWSKYTest Report No.: F145298E1 Date of issue: 08 July 2015Order No.:14-115298page 3 of 3 145298_35.jpg: Reference Design with EUT– Detail Top View

Calculation: RF-Exposure for 2.4 GHz WLAN transmitter Type identification: ODIN-W161 In accordance to theCFR Part 47, §1.1310 S:Limit for power density according to CFR Part 47, §1.1310: 10 W/m 2 P:178 mW (averaged over 30 min) G: 1 dBi = 1.26 D: Duty cycle: 100 % = 1 R: Distance in what the limit of S has to be reached: 0.2 m 222 45.0 )2.0(4 126.1178.0 4m W m W S R DGP S= ×× ×× =Þ ×× ×× = pp The value for the “General population / Uncontrolled Exposure” of the power density is below the limit of CFR Part 47, §1.1310.

Königswinkel 10 32825 Blomberg Germany Phone: +49 (0) 52 35 95 00-0 Fax: +49 (0) 52 35 95 00-10 Test Report Report Number: F145298E3 Applicant: u-blox Malmö AB Manufacturer: u-blox Malmö AB Equipment under Test (EUT): ODIN-W161 Laboratory accredited by Deutsche Akkreditierungsstelle GmbH (DAkkS) in compliance with DIN EN ISO/IEC 17025 under the Reg. No. D-PL-17186-01-02, FCC Test site registration number 90877 and Industry Canada Test site registration IC3469A-1 Test engineer: Wolfgang KASALOWSKYReport Number:F145298E3 Date of issue: 08 July 2015Order Number:14-115298page 2 of 45 REFERENCES [1] ANSI C63.10-2013American National Standard for Methods of Measuring of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. [2] FCC CFR 47 Part 15 (December 2014) Radio Frequency Devices [3] Publication Number 558074 (June 2014) DTS Meas Guidance v03r02 [4] RSS-210 Issue 8 (December 2010) Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment [5] RSS-Gen Issue 4 (November 2014) General Requirements for Compliance of Radio Apparatus TEST RESULT The requirements of the tests performed as shown in the overview (clause 4) were fulfilled by the equipment under test. The complete test results are presented in the following. RESERVATION This test report is only valid in its original form. Any reproduction of its contents in extracts without written permission of the accredited test laboratory PHOENIX TESTLAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TESTLAB GmbH is not responsible for any generalisations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report. Each page necessarily contains the PHOENIX TESTLAB Logo and the TEST REPORT NUMBER. Test engineer: Wolfgang KASALOWSKY08 July 2015 NameSignatureDate Authorized reviewer: Bernd STEINER08 July 2015 Name Signature Date Test engineer: Wolfgang KASALOWSKYReport Number:F145298E3 Date of issue: 08 July 2015Order Number:14-115298page 3 of 45 Contents:Page 1IDENTIFICATION ....................................................................................................................................4 1.1Applicant ..........................................................................................................................................4 1.2Manufacturer ....................................................................................................................................4 1.3Test laboratory .................................................................................................................................4 1.4EUT (Equipment under Test) ............................................................................................................5 1.5Dates ...............................................................................................................................................6 2OPERATIONAL STATES .........................................................................................................................7 3ADDITIONAL INFORMATION ................................................................................................................ 10 4OVERVIEW ........................................................................................................................................... 10 5TEST RESULTS .................................................................................................................................... 11 5.1Maximum peak output power.......................................................................................................... 11 5.1.1Method of measurement .......................................................................................................... 11 5.1.2Test results ............................................................................................................................. 12 5.2DTS Bandwidth .............................................................................................................................. 13 5.2.1Method of measurement .......................................................................................................... 13 5.2.2Test result ............................................................................................................................... 14 5.3Peak Power Spectral Density ......................................................................................................... 15 5.3.1Method of measurement .......................................................................................................... 15 5.3.2Test result ............................................................................................................................... 16 5.4Band-edge compliance ................................................................................................................... 17 5.4.1Method of measurement (band edges next to unrestricted bands (radiated))............................ 17 5.4.2Test result (band edges next to unrestricted bands (radiated)) ................................................. 18 5.4.3Method of measurement (band edges next to restricted bands (radiated)) ............................... 20 5.4.4Test result (band edges next to restricted bands (radiated)) ..................................................... 20 5.5Maximum unwanted emissions ....................................................................................................... 24 5.5.1Method of measurement (radiated emissions) ......................................................................... 24 5.5.2Test results (radiated emissions) ............................................................................................. 31 5.5.2.1Preliminary radiated emission measurement ............................…

Text truncated - open the document above for the full version.

Königswinkel 10 32825 Blomberg Germany Phone: +49 (0) 52 35 95 00-0 Fax: +49 (0) 52 35 95 00-10 Test Report Report Number: F145298E1 Applicant: u-blox Malmö AB Manufacturer: u-blox Malmö AB Equipment under Test (EUT): ODIN-W161 Laboratory accredited by Deutsche Akkreditierungsstelle GmbH (DAkkS) in compliance with DIN EN ISO/IEC 17025 under the Reg. No. D-PL-17186-01-02, FCC Test site registration number 90877 and Industry Canada Test site registration IC3469A-1 Test engineer: Wolfgang KASALOWSKYReport Number:F145298E1 Date of issue: 8 July 2015Order Number:14-115298page 2 of 44 REFERENCES [1] ANSI C63.10-2013American National Standard for Methods of Measuring of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. [2] FCC CFR 47 Part 15 (December 2014) Radio Frequency Devices [3] Publication Number 558074 (June 2014) DTS Meas Guidance v03r02 [4] RSS-210 Issue 8 (December 2010) Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment [5] RSS-Gen Issue Issue 4 (November 2014) General Requirements for Compliance of Radio Apparatus TEST RESULT The requirements of the tests performed as shown in the overview (clause 4) were fulfilled by the equipment under test. The complete test results are presented in the following. RESERVATION This test report is only valid in its original form. Any reproduction of its contents in extracts without written permission of the accredited test laboratory PHOENIX TESTLAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TESTLAB GmbH is not responsible for any generalisations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report. Each page necessarily contains the PHOENIX TESTLAB Logo and the TEST REPORT NUMBER. Test engineer: Wolfgang KASALOWSKY15 July 2015 NameSignatureDate Authorized reviewer: Bernd STEINER15 July 2015 Name Signature Date Test engineer: Wolfgang KASALOWSKYReport Number:F145298E1 Date of issue: 8 July 2015Order Number:14-115298page 3 of 44 Contents:Page 1IDENTIFICATION ....................................................................................................................................4 1.1Applicant ..........................................................................................................................................4 1.2Manufacturer ....................................................................................................................................4 1.3Test laboratory .................................................................................................................................4 1.4EUT (Equipment under Test) ............................................................................................................5 1.5Technical data of equipment.............................................................................................................5 1.6Product Information ..........................................................................................................................6 1.7Dates ...............................................................................................................................................6 2OPERATIONAL STATES .........................................................................................................................7 3OVERVIEW ........................................................................................................................................... 10 4TEST RESULTS .................................................................................................................................... 11 4.1Maximum peak output power.......................................................................................................... 11 4.1.1Method of measurement .......................................................................................................... 11 4.1.2Test results ............................................................................................................................. 12 4.2DTS Bandwidth .............................................................................................................................. 13 4.2.1Method of measurement .......................................................................................................... 13 4.2.2Test result ............................................................................................................................... 14 4.3Peak Power Spectral Density ......................................................................................................... 15 4.3.1Method of measurement .......................................................................................................... 15 4.3.2Test result ............................................................................................................................... 16 4.4Band-edge compliance ................................................................................................................... 17 4.4.1Method of measurement (band edges next to unrestricted bands (radiated))............................ 17 4.4.2Test result (band edges next to unrestricted bands (radiated)) ................................................. 18 4.4.3Method of measurement (band edges next to restricted bands (radiated)) ............................... 20 4.4.4Test result (band edges next to restricted bands (radiated)) ..................................................... 20 4.4.5Method of measurement (radiated emissions) ......................................................................... 23 4.4.6Test results (radiated emissions) ............................................................................................. 30 4.4.6.1Preliminary radiated emission measurement .............…

Text truncated - open the document above for the full version.

Königswinkel 10 32825 Blomberg Germany Phone: +49 (0) 52 35 95 00-0 Fax: +49 (0) 52 35 95 00-10 Test Report Report Number: F145298E2 Applicant: u-blox Malmö AB Manufacturer: u-blox Malmö AB Equipment under Test (EUT): ODIN-W161 Laboratory accredited by Deutsche Akkreditierungsstelle GmbH (DAkkS) in compliance with DIN EN ISO/IEC 17025 under the Reg. No. D-PL-17186-01-02, FCC Test site registration number 90877 and Industry Canada Test site registration IC3469A-1 Test engineer: Wolfgang KASALOWSKYReport Number:F145298E2 Date of issue: 08 July 2015Order Number:14-115298page 2 of 41 REFERENCES [1] ANSI C63.10-2013American National Standard for Methods of Measuring of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. [2] FCC CFR 47 Part 15 (Dec…

Text truncated - open the document above for the full version.