QA5-ORB-02001Wireless Router Bridge

A Outdoor Wireless Router/Bridge User’s Manual Before operating the unit, please read this manual thoroughly, and retain it for future reference . i ■ Contents CHAPTER 1. HARDWARE INSTA LLATION ........................................... 1 1.1 B EFORE Y OU S TART ............................................................................. 1 1.2 L OCATE THE R OUTER /B RIDGE AND I NLINE P OWER I NJECTOR P ORTS ....... 2 1.3 P REPARING I NSTALLATION ..................................................................... 3 1.4 O UTDOOR I NSTALLATION ....................................................................... 5 1.4.1 Antenna Mast R equirement s......................................................... 6 1.4.2 Grounding ...................................................................................... 6 1.4.3 Antenna Ali gnment ........................................................................ 7 CHAPTER 2. NETWORK TOPO LOGIES................................................. 8 2.1 R EMOTE W IRELESS B RIDGE - TO -C ENTRAL W IRELESS B RIDGE ................. 9 2.2 R EMOTE W IRELESS R OUTER - TO -C ENTRAL W IRELESS B RIDGE .............. 10 2.3 R EMOTE W IRELESS B RIDGE - TO -C ENTRAL W IRELESS R OUTER .............. 11 2.4 R EMOTE W IRELESS R OUTER - TO -C ENTRAL W IRELESS R OUTER ............ 12 CHAPTER 3. WEB ACC ESS.................................................................. 13 CHAPTER 4. CONFIGURAT ION............................................................ 17 4.1 I NTRODUCTION ................................................................................... 17 4.1.1 Basic Configur ation St eps ........................................................... 17 4.2 S YSTEM S ETUP ................................................................................... 19 A FTER THAT , CLICK FINISH AT THE BOTTOM OF THIS PAGE TO COMPLETE THE MODIFICATION OF THIS PAGE . ......................................................................... 23 A FTER THAT , CLICK FINISH AT THE BOTTOM OF THIS PAGE TO COMPLETE THE MODIFICATION OF THIS PAGE . ......................................................................... 24 A FTER THAT , CLICK FINISH AT THE BOTTOM OF THIS PAGE TO COMPLETE THE MODIFICATION OF THIS PAGE . ......................................................................... 25 4.3 TCP/IP P ROTOCOL C ONFIGURE .......................................................... 26 4.3.1 Virtual Server Mapping................................................................ 26 4.4 C ONFIGURE DHCP SERVER ................................................................ 28 4.4.1 General DHCP Server Parameter............................................... 29 4.4.2 Fixed Host Entries ....................................................................... 29 4.5 C ONFIGURE SNMP............................................................................. 31 4.5.1 Configure Comm unity Pool ......................................................... 31 4.5.2 Configure Trap Host Pool............................................................ 32 4.6 C ONFIGURE W IRELESS RELATED PARAMETERS ..................................... 34 4.7 S ECURITY ........................................................................................... 36 ii 4.7.1 MAC based Access Contro l ........................................................ 36 4.8 U TILITY ............................................................................................... 37 4.8.1 Software U pgrade ....................................................................... 37 4.8.2 Administra tion.............................................................................. 38 CHAPTER 5. STATUS MO NITOR.......................................................... 39 5.1 S YSTEM I NFORMATION ........................................................................ 40 5.2 DHCP I NFORMATION .......................................................................... 41 5.3 S TATION I NFORMATION ........................................................................ 42 5.4 S TATISTIC I NFORMATION ..................................................................... 43 5.5 W IRELESS L INK I NFORMATION ............................................................ 44 CHAPTER 6. SPECIFICAT IONS ............................................................ 45 CHAPTER 7. DEFAULT SE TTINGS ...................................................... 47 7.1 G ENERAL C ONFIGURATION .................................................................. 47 7.1.1 System......................................................................................... 47 7.1.2 Virtual Server Mapping................................................................ 48 7.1.3 DHCP .......................................................................................... 49 7.1.4 SNMP .......................................................................................... 50 7.1.5 Wireless LAN............................................................................... 52 7.2 U TILITY ............................................................................................... 53 7.2.1 Software U pgrade ....................................................................... 53 7.2.2 Administra tion.............................................................................. 53 CHAPTER 8. REGULATORY COMPLIANCE INFORMATION ............. 54 1 Chapter 1. Hardware Installation This chapter describes the proc edures for installing the Outdoor Router/Bridge. Note: Before you mount the Router/Bridge to a mast or on the side of a building, be sure to configure and test the device first. 1.1 Before You Start After unpacking the system, make sure the following items are present and in good condition. 1. Router/Bridge 2. Inline Power Injector 3. AC Power Cord 4. MIL-C-5015 style RS232 Console Port Cable 5. Grounding Wire 6. Cross over Ethernet Cable 7. Reverse Polarity-N Female RF C…

Text truncated - open the document above for the full version.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 November 20, 2002 RE: SendFar Technology Co., Ltd. FCC ID: QA5-ORB-02001 After a review of the submitted information, I have a few comments on the above referenced Application. 1) FYI, the DoC is actually required because the DoC authorization applies to the device as a PC Peripheral, not as a receiver. Note that the scope of Part 15 only applies to receivers between 30-960 MHz. 2) Please provided information regarding the PCMCIA card integrated into this device. For instance, what is the manufacturer, model, FCC ID # (if applicable), etc. 3) Is the PCMCIA card unmodified/modified from the original approval (if applicable) or is this a special version being used strictly for this purpose? Please explain what the changes are that were made. Note that an external antenna is being used, but the device still appears to contain 2 internal antennas. 4) Please confirm that the schematics provided are for the PCMCIA card used, including any modifications made for inclusion into this device. 5) Are test photographs available for both Radiated test configurations? 6) The RF output specified in the users manual is 24 dBm, while the measured value was 18.6 dBm. Please comment and correct all affected exhibits. 7) The users manual states that the connector is an SMA., while the device does not appear to contain any SMA connectors. Please comment and correct any affected exhibits. 8) The users manual does not appear to contain the information specified by 15.21. 9) The limits for 2680 MHz given on page 29 should be 54/74 dBuV as they fall in a restricted band. Please correct. Timothy R. Johnson Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Tim, For Item 2: Only the manufacturer were provided: Z-UP Technologies Corporation For Item 3: The PCMCIA card is being used strictly for this device. For Item 4: the schematics for the PCMCIA card, please refer to page 9-11 on the file "Schem_QA5-ORB-02001" which had been upload on your website. For Item 5: See uploaded file For Item 6, 7, 8 & 9: Please see the revised files which had been re-uploaded on your website. Thank You, Rennie (See attached file: ATCB Comments_111902.pdf) ATCB Comments_111902.pdf To: [email protected] Cc: [email protected] Subject: RE =?big5?B? oUcgUmV2aWV3IG9mIFNlbmRGYXIgVGVjaG5vbG9neSwgRkNDIElEOiBRQTUtT1JC?= =?us-ascii?Q?-02001?= 11/20/2002file://C:\DOCUME~1\TIMOTH~1.JOH\LOCALS~1\Temp\eud1EE.htm

Page 6 Page 7 Page 8

Page 11 Page 12 Page 13 Page 14 Page 16 Page 17 Page 18 Page 19

Page 21 Page 22 Page 23

Label Location S/N: Wireless Router Bridge MADE IN TAIWAN This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. FOR HOME OR OFFICE USE Tested To Comply With FCC Standards 116 mm 4 5 m m Model No.: RB-8110 FCC ID: QA5-ORB-02001

Page 8 Page 9 Page 10

Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34

FCC ID: QA5-ORB-02001 ADT No.910923R01 Operational Description The transmitter of the EUT is powered by POE (Power over Ethernet) and connected with managing computer through RJ45 port. The antenna type is Patch antenna with Reversed N Type connector. Under normal use condition, the user has to keep at least 20cm separation distance between radiator and the body of the user. The other instruction, please have a look at the users manual. DSSS Information This device is Direct Sequence Spread Spectrum, the data is mixed by pseudorandom code which is an orthogonal code. The mixed data is digital modulated by BPSK and QPSK technique depends on the data rates. The CCK coding is applied for increasing the data rate, and also the processing gain will be increased. The bit rates are 1,2,5.5,11Mbps, the symbol rates are 1,1,1.375,1.375Mbps, the chip rates are always 11Mbps. So, the Chip/symbol is 11,11,8 and 8 respectively. Although is higher bit rate, the processing gain is lower than 10, but the CCK coding used in higher bit rate will provide 2.2dB coding gain.

FCC ID: QA5-ORB-02001 ADT No.: 910923R01 FCC TEST REPORT REPORT NO.: RF910923R01 MODEL NO.: RB-8110 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: SendFar Technology Co., Ltd. ADDRESS: 15F, No. 866-2, Jung Jeng Rd., Junghe City, Taipei, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: 47 14th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. 0528 ILAC MRA Lab Code: 200102-0 FCC ID: QA5-ORB-02001 ADT No.: 910923R01 RF Exposure Measurement (Mobile Device) 1. Introduction 2.4GHz frequency band is regarded specially as a dangerous band for its heating harmfulness to the human body. That’s why microwave oven is operating in this frequency band. The manufacturer whose product is working in this frequency band is obligatory to prove the harmfulness of his product. In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC), and the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. 2. Classification The antenna of the product, under normal use condition, is at least 20cm away from the body of the user. Warning statement for keeping 20cm separation distance and the prohibition of operating next to a person has been printed on the user’s manual. So, this product is classified as the Mobile Device. 3. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). FCC ID: QA5-ORB-02001 ADT No.: 910923R01 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 30-30061.40.1631.06 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 30-30027.50.0730.230 300-1500......F/150030 1500-100,000......1.030 F = Frequency in MHz 4. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm 2 . If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 5. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: QA5-ORB-02001 ADT No.: 910923R01 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 12dBi or 15.85 (numeric). 6.2 Output Power Into Antenna & RF Exposure Distance : CHANNEL CHANNEL FREQUENCY (MHz) OUTPUT POWER TO ANTENNA (mW) MINIMUM ALLOWABLE DISTANCE ( r ) FROM SKIN (Centi-Meter) 1241271.789.51 6243772.449.56 11246272.449.56 The minimum allowable distance is very close to the enclosure of the antenna. So, the user has no need to worry about the harmfulness of radiation. But it is recommended to always keep, at least, 20cm separation distance with the antenna.

FCC ID: QA5-ORB-02001 Report No.: RF910923R011Issued: Nov. 18, 2002 FCC TEST REPORT REPORT NO.: RF910923R01 MODEL NO.: RB-8110 RECEIVED: Sept. 23, 2002 TESTED: Oct. 15 ~ Nov. 16, 2002 APPLICANT:SendFar Technology Co., Ltd. ADDRESS: 15F, No. 866-2, Jung Jeng Rd., Junghe City, Taipei, Taiwan, R.O.C. ISSUED BY:Advance Data Technology Corporation LAB LOCATION:47 14 th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. This test report consists of 52 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA Lab Code: 200102-0 FCC ID: QA5-ORB-02001 Report No.: RF910923R012Issued: Nov. 18, 2002 Table of Contents 1CERTIFICATION.....................................................................................................4 2SUMMARY OF TEST RESULTS.............................................................................5 3GENERAL INFORMATION .....................................................................................6 3.1GENERAL DESCRIPTION OF EUT........................................................................6 3.2DESCRIPTION OF TEST MODES..........................................................................7 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS .........................................7 3.4DESCRIPTION OF SUPPORT UNITS....................................................................8 4TEST TYPES AND RESULTS.................................................................................9 4.1CONDUCTED EMISSION MEASUREMENT ..........................................................9 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................9 4.1.2 TEST INSTRUMENTS ............................................................................................9 4.1.3 TEST PROCEDURES ..........................................................................................10 4.1.4 DEVIATION FROM TEST STANDARD .................................................................10 4.1.5 TEST SETUP........................................................................................................ 11 4.1.6 EUT OPERATING CONDITIONS.......................................................................... 11 4.1.7 TEST RESULTS ...................................................................................................12 4.2RADIATED EMISSION MEASUREMENT .............................................................18 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ...........................................18 4.2.2 TEST INSTRUMENTS ..........................................................................................19 4.2.3 TEST PROCEDURES ..........................................................................................20 4.2.4 DEVIATION FROM TEST STANDARD .................................................................20 4.2.5 TEST SETUP........................................................................................................21 4.2.6 EUT OPERATING CONDITIONS..........................................................................21 4.2.7 TEST RESULTS (A)..............................................................................................22 4.2.8 TEST RESULTS (B)..............................................................................................26 4.36dB BANDWIDTH MEASUREMENT ....................................................................30 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ..................................................30 4.3.2 TEST INSTRUMENTS ..........................................................................................30 4.3.3 TEST PROCEDURE.............................................................................................31 4.3.4 DEVIATION FROM TEST STANDARD .................................................................31 4.3.5 TEST SETUP........................................................................................................31 4.3.6 EUT OPERATING CONDITIONS..........................................................................31 4.3.7 TEST RESULTS ...................................................................................................32 4.4MAXIMUM PEAK OUTPUT POWER ....................................................................36 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT .....................36 4.4.2 INSTRUMENTS....................................................................................................36 4.4.3 TEST PROCEDURES ..........................................................................................37 4.4.4 DEVIATION FROM TEST STANDARD .................................................................37 4.4.5 TEST SETUP........................................................................................................37 4.4.6 EUT OPERATING CONDITIONS..........................................................................37 4.4.7 TEST RESULTS ...................................................................................................38 4.5POWER SPECTRAL DENSITY MEASUREMENT ................................................39 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..............................39 4.5.2 TEST INSTRUMENTS ..........................................................................................39 FCC ID: QA5-ORB-02001 Report No.: RF910923R013Issued: Nov. 18, 2002 4.5.3 TEST PROCEDURE.............................................................................................40 4.5.4 DEVIATION FROM TEST STANDARD .................................................................40 4.5.5 TEST SETUP................................................…

Text truncated - open the document above for the full version.

FCC ID: QA5-ORB-02001 Report No.: RF910923R0150Issued: Nov. 18, 2002 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: QA5-ORB-02001 Report No.: RF910923R0151Issued: Nov. 18, 2002 RADIATED EMISSION TEST

FCC ID: QA5-ORB-02001 Report No.: RF910923R0150Issued: Nov. 18, 2002 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: QA5-ORB-02001 Report No.: RF910923R0151Issued: Nov. 18, 2002 RADIATED EMISSION TEST