QISAP5130DNWireless LAN Access Point

AP3x10xN&5x10xN&5x30xN&6x10xN&7x10xN Hardware Installation and Maintenance Guide Issue 12 Date2015-08-05 HUAWEI TECHNOLOGIES CO., LTD. Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address:Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website:http://e.huawei.com Issue 12 (2015-08-05)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. i About This Document Intended Audience This document describes hardware features of AP3x10xN, 5x10xN, 5x30xN, 6x10xN and 7x10xN, and provides basic installation methods. This document is intended for: lNetwork planning engineers lHardware installation engineers lCommissioning engineers lOnsite maintenance engineers lSystem maintenance engineers Symbol Conventions The symbols that may be found in this document are defined as follows. SymbolDescription Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. NOTICE is used to address practices not related to personal injury. AP3x10xN&5x10xN&5x30xN&6x10xN&7x10xN Hardware Installation and Maintenance GuideAbout This Document Issue 12 (2015-08-05)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. ii SymbolDescription NOTE Calls attention to important information, best practices and tips. NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration. Change History Changes between document issues are cumulative. The latest document issue contains all changes made in previous issues. Issue 12 (2015-08-05) This version has the following updates: Updated the packing list. Issue 11 (2015-05-18) This version has the following updates: The following information is modified: lAdded the command to check AP running status in V200R006C00. lAdded descriptions about PoE fault troubleshooting. Issue 10 (2014-12-05) This version has the following updates: The following information is added: l1.4 Ordering Information. Issue 09 (2014-07-30) This version has the following updates: The following information is modified: lOptimized the installation steps. The following information is added: lLogging in to the AP using STelnet. Issue 08 (2013-04-10) This version has the following updates: The following information is added: AP3x10xN&5x10xN&5x30xN&6x10xN&7x10xN Hardware Installation and Maintenance Guide About This Document Issue 12 (2015-08-05)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. iii lAP5030DN and AP5130DN installation guide lNote: The network cable cannot exceed 100 meters. Issue 07 (2014-01-15) This version has the following updates: Optimized the manual. Issue 06 (2013-09-30) This version has the following updates: The following information is modified: lAP's default IP address and login password Issue 05 (2013-06-29) This version has the following updates: The following information is modified: lFigure for converting SMA connectors to type—N connectors Issue 04 (2013-04-30) This version has the following updates: The following information is modified: lFigure of the sheet metal mounting brackets delivered with APs Issue 03 (2013-01-30) This version has the following updates: The following information is added: lDescriptions about power adapters delivered with APs lSection: Removing an AP Issue 02 (2012-12-31) This version has the following updates: The following information is added: lPower adapter cable connection figure Issue 01 (2012-10-31) Initial commercial release AP3x10xN&5x10xN&5x30xN&6x10xN&7x10xN Hardware Installation and Maintenance Guide About This Document Issue 12 (2015-08-05)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. iv Contents About This Document.....................................................................................................................ii 1 Indoor AP Overview.....................................................................................................................1 1.1 Device Structure.............................................................................................................................................................1 1.2 Indicator Description......................................................................................................................................................4 1.3 Basic Specifications...............................…

Text truncated - open the document above for the full version.

RF_160, Issue 02 Declaration of Authorization We Name: Huawei Technologies Co.,Ltd Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District City: Shenzhen Country: China Declare that: Name Representative of agent: Ms. Cathy Wang Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s): Product description: Wireless LAN Access Point Type designation: AP5130DN Trademark: HUAWEI on our behalf. Date: 2015-08-19 City: Shenzhen Name: Zhang Xinghai Signature:  . Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

FCC, Request for non-disclosure Date: 10-Aug-09 RF_501, Issue 5 Page 1 of 1 Company Name: Huawei Technologies Co.,Ltd Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District City: Shenzhen Country: China To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: QISAP5130DN Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: These documents contain detailed system and equipment description considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitor unfair advantage in the market. Planned Release Date STC: 180 days from date of grant (notes 2, 3, 4, 5) Date: 2015-08-19 Name and signature of applicant: Zhang Xinghai Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. FCC, Request for non-disclosure Date: 10-Aug-09 RF_501, Issue 5 Page 1 of 1 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Huawei Technologies Co.,Ltd Ad Hoc Mode Declaration Date: 2015-08-19 We, the undersigned company Company Name: Huawei Technologies Co.,Ltd Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, China Declare that: Product description: Wireless LAN Access Point Type designation: AP5130DN Brand: HUAWEI FCC ID: QISAP5130DN 1. The EUT doesn’t have Ad Hoc Mode function on “non-US frequencies”. 802.11a/n Ad Hoc mode should not be supported even on US DFS frequencies (5.25 ~5.35GHz/5.47 ~5.725GHz). 2. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US. The product meets all other requirements specified in Part 15E Section 15.407 and no configuration controls are provided to change the frequency of operations outside the grant of certification for US operation. 3. Only channels 1~11 will be used in USA. Country code selection is disabled. If you have any questions regarding the authorization, please do not hesitate to contact us, thank you~ Sincerely, Signature: ____ ____________________ Name: Zhang Xinghai Tel: +86-755-2897-0299 Email: [email protected]

Huawei Technologies Co.,Ltd Declaration Letter Date: 2015-09-01 We, the undersigned company Company Name: Huawei Technologies Co.,Ltd Address: Administration Building, Headquarters of Huawei, Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, China Declare that: Product description: Wireless LAN Access Point Type designation: AP5130DN Brand: HUAWEI FCC ID: QISAP5130DN this device with Bridge and Mesh modes of operation are permitted to operate in the DFS band and employ a DFS function. The functionality of the Bridge mode as specified in §15.403(a) and the Mesh mode is validated in the DFS test report by performing a test statistical performance check on any one of the radar types. If you have any questions regarding the authorization, please do not hesitate to contact us, thank you~ Sincerely, Signature: __________ Name: Zhang Xinghai Tel: +86-755-2897-0299 Email: [email protected]

Project No.: 1507C117 Page 2 of 13 Project No.: 1507C117 Page 3 of 13 Project No.: 1507C117 Page 4 of 13 Project No.: 1507C117 Page 5 of 13 Project No.: 1507C117 Page 6 of 13

FORM PSF0101D 制作要求: 尺寸:70*100mm 材质:PET(哑银)Fasson72826,厚度PET+背胶+离芯纸不大于0.1mm； 背丙烯酸丁酯或具有同类物性的其它丙烯酸胶,要求在高温70度,高湿90%, 低温-25度的环境中时间各8H不脱落不翘起不起泡 颜色:黑色印刷 来料方式:圈装 SN:21XXXXXXXX8WYMNNNNNN Y AP5130DN MAC:30D17EB18780-9F(32) 华为技术有限公司中国制造 MADE IN CHINA 电源额定值 POWER RATING: DC 12 V; 2 A or PoE - 48 V; 0.35 A FCC ID:QISAP5130DNFCC ID:QISAP5130DN IC:6369A-AP5130DNIC:6369A-AP5130DN This device complies with Part 15 of the FCC Rules.Operation isThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause subject to the following two conditions:(1) this device may not cause harmful interference,and (2) this device must accept any interferenceharmful interference,and (2) this device must accept any interference received,including interferences that may cause undesired operation.received,including interferences that may cause undesired operation. CAN ICES-3(B)/NMB-3(B)CAN ICES-3(B)/NMB-3(B) CMIIT ID:2014AP0952CMIIT ID:2014AP0952 AP5130DNAP5130DN

Project No.: 1507C117 Page 7 of 13 Project No.: 1507C117 Page 8 of 13 Project No.: 1507C117 Page 9 of 13 Project No.: 1507C117 Page 10 of 13 Project No.: 1507C117 Page 11 of 13 Project No.: 1507C117 Page 12 of 13 Project No.: 1507C117 Page 13 of 13

FCC RF EXPOSURE REPORT FCC ID: QISAP5130DN Project No. : 1507C117 Equipment : Wireless LAN Access Point Model : AP5130DN Applicant : Huawei Technologies Co.,Ltd. Address : Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District Shenzhen China According: : FCC Guidelines for Human Exposure IEEE C95.1 BTL INC. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, China. TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 MPE CALCULATION METHOD: Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Table for Filed Antenna 2.4G Ant. Manufacturer Model NameAntenna TypeConnector Gain (dBi) Note A GUANGDONG SHENGLU TELECOMMUNICATION TECH. CO.,LTD. SL10301A External Antenna RP-SMA-J 3.87 2.4G B GUANGDONG SHENGLU TELECOMMUNICATION TECH. CO.,LTD. SL10301A External Antenna RP-SMA-J 3.87 2.4G C GUANGDONG SHENGLU TELECOMMUNICATION TECH. CO.,LTD. SL10301A External Antenna RP-SMA-J 3.87 2.4G Note: (1) The EUT incorporates a MIMO function. Physically, the EUT provides three completed transmitters and receivers (3T3R). (2) ANT A for 1TX was found to be the worst case and recorded. Remark: For 2TX with beamforming The EUTwith beamforming function, then, Direction gain = G ANT +10log(N ANT /N SS ), where N SS = the number of independent spatial streams of data. Directional gain=3.87+10log(3/2)=3.87 + 1.76=5.63 So the Output Powerlimit= 30 the PSD limit=8 For 3TX with beamforming The EUTwith beamforming function, then, Direction gain = G ANT +10log(N ANT /N SS ), where N SS = the number of independent spatial streams of data. Directional gain=3.87+10log(3/3)=3.87 So the Output Powerlimit= 30 the PSD limit=6 Operating Mode TX Mode 1TX 2TX 3TX 802.11b V (ANT A) V (ANT A + ANT B) V (ANT A + ANT B + ANT C) 802.11g V (ANT A) V (ANT A + ANT B) V (ANT A + ANT B + ANT C) 802.11n(20MHz) V (ANT A) V (ANT A + ANT B) V (ANT A + ANT B + ANT C) 802.11n(40MHz) V (ANT A) V (ANT A + ANT B) V (ANT A + ANT B + ANT C) 5G Table for Filed Antenna Ant. Manufacturer Model Name Antenna Type Connector Gain (dBi) Note A GUANGDONG SHENGLU TELECOMMUNICATION TECH. CO.,LTD. SL10301A External Antenna RP-SMA-J 5.7 5G B GUANGDONG SHENGLU TELECOMMUNICATION TECH. CO.,LTD. SL10301A External Antenna RP-SMA-J 5.7 5G C GUANGDONG SHENGLU TELECOMMUNICATION TECH. CO.,LTD. SL10301A External Antenna RP-SMA-J 5.7 5G Note: 1. 1. The EUT incorporates a MIMO function. Physically, the EUT provides three completed transmitters and receivers (3T3R). ANT A for 1TX was found to be the worst case and recorded. Remark: For 2TX with beamforming The EUTwith beamforming function, then, Direction gain = G ANT +10log(N ANT /N SS ), where N SS = the number of independent spatial streams of data. Directional gain=5.7+10log(3/2)=5.7 + 1.76=7.46. So the Output Power of UNII-1& UNII-3 limit =30-7.46+6=28.54 the RSS-247 Output Power of UNII-1 limit =23-7.26+6=21.54 the Output Power of UNII-2A&UNII-2C limit = 24-7.46+6=22.54, the PSD of UNII-1 limit =17-7.46+6=15.54, the RSS-247 PSD of UNII-1 limit =10-7.26+6=8.54, the PSD of UNII-2A & UNII-2C limit =11-7.46+6=9.54, the PSD of UNII-3 for AC mode limit =30-7.46+6=28.54. For 3TX with beamforming The EUTwith beamforming function, then, Direction gain = G ANT +10log(N ANT /N SS ), where N SS = the number of independent spatial streams of data. Directional gain=5.7+10log(3/3)=5.7 + 0=5.7. So the Output Power of UNII-1& UNII-3 limit =30 the RSS-247 Output Power of UNII-1 limit =23 the Output Power of UNII-2A&UNII-2C limit = 24 the PSD of UNII-1 limit =17, the RSS-247 PSD of UNII-1 limit =10, the PSD of UNII-2A & UNII-2C limit =11, the PSD of UNII-3 limit =30. Operating Mode TX Mode 1TX 2TX 3TX 802.11a V (ANT A) V (ANT A+ ANT B) V (ANT A+ ANT B + ANT C) 802.11n(20MHz) V (ANT A) V (ANT A+ ANT B) V (ANT A+ ANT B + ANT C) 802.11n(40MHz) V (ANT A) V (ANT A+ ANT B) V (ANT A+ ANT B + ANT C) 802.11ac(20MHz) V (ANT A) V (ANT A+ ANT B) V (ANT A+ ANT B + ANT C) 802.11ac(40MHz) V (ANT A) V (ANT A+ ANT B) V (ANT A+ ANT B + ANT C) 802.11ac(80MHz) V (ANT A) V (ANT A+ ANT B) V (ANT A+ ANT B + ANT C) TEST RESULTS 2.4G EUT： Wireless LAN Access Point Model Name : AP5130DN Temperature： 27 °C Relative Humidity: 55 % Test Voltage : AC 120V/60Hz Test Mode ： TX B MODE /CH01, CH06, CH11-Ant A+Ant B Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.87 2.4378 16.02 39.9945 0.019406641 Complies 3.87 2.4378 16.99 50.0035 0.024263331 Complies 3.87 2.4378 16.02 39.9945 0.019406641 Complies EUT： Wireless LAN Access Point Model Name : AP5130DN Temperature： 27 °C Relative Humidity: 55 % Test Voltage : AC 120V/60Hz Test Mode ： TX G MODE /CH01, CH06, CH11-Ant A+Ant B Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.87 2.4378 20.00 100.0000 0.048523301 Complies 3.87 2.4378 23.22 209.8940 0.101847501 Complies 3.87 2.4378 21.46 139.9587 0.067912601 Complies EUT： Wireless LAN Access Point Model Name : AP5130DN Temperature: 27 °C Relative Humidity: 55 % Test Voltage : AC 120V/60Hz Test Mode : TX N-20M MODE /CH01, CH06, CH11-Ant A+Ant B Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.87 2.4378 20.79 119.9499 0.058203671 Complies 3.87 2.4378 23.22 209.8940 0.101847501 Complies 3.87 2.4378 21.14 130.0170 0.063088521 Complies EUT： Wireless LAN Access Point Model Name : AP5130DN Temperature: 27 °C Relative Humidity: 55 % Test Voltage : AC 120V/60Hz Test Mode : TX N-40M MODE /CH03, CH06, CH09-Ant A+Ant B Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Powe…

Text truncated - open the document above for the full version.

Report No.: BTL-FICP-2-1507C117 Page 1 of 1301 FCC&IC Radio Test Report FCC ID: QISAP5130DN IC: 6369A-AP5130DN This report concerns (check one): Original Grant Class II Change Project No. : 1507C117 Equipment : Wireless LAN Access Point Model Name : AP5130DN Applicant : Huawei Technologies Co.,Ltd. Address for FCC : Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District Shenzhen China Address for IC : Administration Building, Headquarters of Huawei Technologies Co., Ltd.,Bantian, Longgang District, Shenzhen 518129 China Date of Receipt : Jul. 09, 2015 Date of Test : Jul. 09, 2015 ~ Aug. 17, 2015 Issued Date : Aug. 18, 2015 Tested by : BTL Inc. Testing Engineer : (Niklaus Lai) Technical Manager : (David Mao) Authorized Signatory : (Steven Lu) BTL INC. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China. TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 Report No.: BTL-FICP-2-1507C117 Page 2 of 1301 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTLshall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. BTL’s report must not be used by the client to claim product certification, approval, or endorsement b y NVLAP, NIST, or any agency of the Federal Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and BTL-self, extracts from the test report shall not be reproduced except in full with BTL’s authorized written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: BTL-FICP-2-1507C117 Page 3 of 1301 Table of Contents Page 1 . CERTIFICATION 7 2 . SUMMARY OF TEST RESULTS 8 2.1 TEST FACILITY 9 2.2 MEASUREMENT UNCERTAINTY 9 3 . GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 19 3.3 TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 21 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 32 3.5 DESCRIPTION OF SUPPORT UNITS 32 4 . EMC EMISSION TEST 33 4.1 CONDUCTED EMISSION MEASUREMENT 33 4.1.1 POWER LINE CONDUCTED EMISSION 33 4.1.2 TEST PROCEDURE 33 4.1.3 DEVIATION FROM TEST STANDARD 33 4.1.4 TEST SETUP 34 4.1.5 EUT OPERATING CONDITIONS 34 4.1.6 EUT TEST CONDITIONS 34 4.1.7 TEST RESULTS 34 4.2 RADIATED EMISSION MEASUREMENT 35 4.2.1 RADIATED EMISSION LIMITS 35 4.2.2 TEST PROCEDURE 36 4.2.3 DEVIATION FROM TEST STANDARD 36 4.2.4 TEST SETUP 36 4.2.5 EUT OPERATING CONDITIONS 37 4.2.6 EUT TEST CONDITIONS 37 4.2.7 TEST RESULTS (9K TO 30MHz) 38 4.2.8 TEST RESULTS (BETWEEN 30 TO 1000 MHz) 38 4.2.9 TEST RESULTS (ABOVE 1000 MHz) 38 5 . 26dB SPECTRUM BANDWIDTH 39 5.1 APPLIED PROCEDURES / LIMIT 39 5.1.1 TEST PROCEDURE 39 5.1.2 DEVIATION FROM STANDARD 39 5.1.3 TEST SETUP 39 5.1.4 EUT OPERATION CONDITIONS 40 5.1.5 EUT TEST CONDITIONS 40 5.1.6 TEST RESULTS 40 6 . MAXIMUM CONDUCTED OUTPUT POWER 41 Report No.: BTL-FICP-2-1507C117 Page 4 of 1301 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 41 6.1.1 TEST PROCEDURE 41 6.1.2 DEVIATION FROM STANDARD 42 6.1.3 TEST SETUP 42 6.1.4 EUT OPERATION CONDITIONS 42 6.1.5 EUT TEST CONDITIONS 42 6.1.6 TEST RESULTS 42 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 43 7.1 APPLIED PROCEDURES / LIMIT 43 7.1.1 TEST PROCEDURE 43 7.1.2 DEVIATION FROM STANDARD 43 7.1.3 TEST SETUP 43 7.1.4 EUT OPERATION CONDITIONS 43 7.1.5 EUT TEST CONDITIONS 43 7.1.6 TEST RESULTS 43 8 . POWER SPECTRAL DENSITY TEST 44 8.1 APPLIED PROCEDURES / LIMIT 44 8.1.1 TEST PROCEDURE 44 8.1.1 DEVIATION FROM STANDARD 45 8.1.2 TEST SETUP 45 8.1.3 EUT OPERATION CONDITIONS 45 8.1.4 EUT TEST CONDITIONS 45 8.1.5 TEST RESULTS 45 9 . FREQUENCY STABILITY MEASUREMENT 46 9.1 APPLIED PROCEDURES / LIMIT 46 9.1.1 TEST PROCEDURE 46 9.1.2 DEVIATION FROM STANDARD 46 9.1.3 TEST SETUP 47 9.1.4 EUT OPERATION CONDITIONS 47 9.1.5 EUT TEST CONDITIONS 47 9.1.6 TEST RESULTS 47 10 . MEASUREMENT INSTRUMENTS LIST 48 11 . EUT TEST PHOTOS 50 ATTACHMENT A - CONDUCTED EMISSION 54 ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) 57 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) 59 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) 84 ATTACHMENT E - BANDWIDTH 327 Report No.: BTL-FICP-2-1507C117 Page 5 of 1301 Table of Contents Page ATTACHMENT F - MAXIMUM OUTPUT POWER 373 ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION 508 ATTACHMENT H - POWER SPECTRAL DENSITY 753 ATTACHMENT I - FREQUENCY STABILITY 1297 Report No.: BTL-FICP-2-1507C117 Page 6 of 1301 REPORT ISSUED HISTORY Issued No. Description Issued Date BTL-FICP-2-1507C117 Original Issue. Aug. 18, 2015 Report No.: BTL-FICP-2-1507C117 Page 7 of 1301 1. CERTIFICATION Equipment : Wireless LAN Access Point Brand Name : HUAWEI Model Name : AP5130DN Applicant : Huawei Technologies Co.,Ltd. Manufacturer : Huawei Technologies Co.,Ltd. Address : Administration Building, Huawei Base, Bantian, Longgang District ,Shenzhen 518129, P.R.China Factory : Huawei Technologies Co.,Ltd. Address : Huawei Base, Bantian, Longgang District, Shenzhen 518129, P.R.China Date of Test : Jul. 09, 2015 ~ Aug. 17, 2015 Test Sample : ENGINEERING SAMPLE Standard(s) : FCC Part15, Subpart E(15.407) / ANSI C63.10: 2013 Canada RSS-…

Text truncated - open the document above for the full version.

Report No.: BTL-FICP-2-1507C117 Page 355 of 1301 TX CH38 TX CH46 Report No.: BTL-FICP-2-1507C117 Page 356 of 1301 Test Mode: UNII-1/TX AC80 Mode_CH42 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH42 5210 82.39 75.60 TX CH42 Report No.: BTL-FICP-2-1507C117 Page 357 of 1301 Test Mode: UNII-2A/TX AC20 Mode_CH52/CH60/CH64 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH52 5260 23.15 18.00 CH60 5300 23.20 18.00 CH64 5320 23.19 18.00 TX CH52 Report No.: BTL-FICP-2-1507C117 Page 358 of 1301 TX CH60 TX CH64 Report No.: BTL-FICP-2-1507C117 Page 359 of 1301 Test Mode: UNII-2A/TX AC40 Mode_CH54/CH62 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH54 5270 43.51 36.40 CH62 5310 43.20 36.40 Report No.: BTL-FICP-2-1507C117 Page 360 of 1301 TX CH54 TX CH62 Report No.: BTL-FICP-2-1507C117 Page 361 of 1301 Test Mode: UNII-2A/TX AC80 Mode_CH58 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH58 5290 83.60 76.00 TX CH58 Report No.: BTL-FICP-2-1507C117 Page 362 of 1301 Test Mode: UNII-2C/TX AC20 Mode_CH100/CH116/CH140 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH100 5500 22.60 18.00 CH116 5580 23.85 18.00 CH140 5700 22.89 18.00 TX CH100 Report No.: BTL-FICP-2-1507C117 Page 363 of 1301 TX CH116 TX CH140 Report No.: BTL-FICP-2-1507C117 Page 364 of 1301 Test Mode: UNII-2C/TX AC40 Mode_CH102/CH110/CH134 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH102 5510 43.50 36.40 CH110 5550 43.39 36.40 CH134 5670 43.50 36.40 TX CH102 Report No.: BTL-FICP-2-1507C117 Page 365 of 1301 TX CH110 TX CH134 Report No.: BTL-FICP-2-1507C117 Page 366 of 1301 Test Mode: UNII-2C/TX AC80 Mode_CH106/CH122 Channel Frequency (MHz) 26dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) CH106 5530 83.59 76.00 CH122 5610 84.00 76.00 Report No.: BTL-FICP-2-1507C117 Page 367 of 1301 TX CH106 TX CH122 Report No.: BTL-FICP-2-1507C117 Page 368 of 1301 Test Mode: UNII-3/ TX AC20 Mode_CH149/CH157/CH165 Channel Frequency (MHz) 6dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) Limit (kHz) CH149 5745 17.75 18.00 >=500 CH157 5785 17.90 18.00 >=500 CH165 5825 17.75 18.00 >=500 TX CH 149 Report No.: BTL-FICP-2-1507C117 Page 369 of 1301 TX CH 157 TX CH 165 Report No.: BTL-FICP-2-1507C117 Page 370 of 1301 Test Mode: UNII-3/ TX AC40 Mode_CH151/CH159 Channel Frequency (MHz) 6dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) Limit (kHz) CH151 5755 36.60 36.40 >=500 CH159 5795 36.50 36.40 >=500 Report No.: BTL-FICP-2-1507C117 Page 371 of 1301 TX CH 151 TX CH 159 Report No.: BTL-FICP-2-1507C117 Page 372 of 1301 Test Mode: UNII-3/ TX AC80 Mode_CH155 Channel Frequency (MHz) 6dB Bandwidth (MHz) 99% Occupied Bandwidth (MHz) Limit (kHz) CH155 5775 76.20 76.00 >=500 TX CH 155 Report No.: BTL-FICP-2-1507C117 Page 373 of 1301 ATTACHMENT F - MAXIMUM OUTPUT POWER Report No.: BTL-FICP-2-1507C117 Page 374 of 1301 For 1TX Test Mode: UNII-1/TX A Mode Channel Frequency (MHz) FCC Part 15E Conducted Output Power (dBm) Duty Factor (dBm) FCC Part 15E Conducted Output Power + Duty Factor (dBm) Limit (dBm) Limit (Watt) CH36 5180 12.54 0.24 12.78 30.00 1.00 CH40 5200 15.01 0.24 15.25 30.00 1.00 CH48 5240 14.95 0.24 15.19 30.00 1.00 Test Mode: UNII-1/TX A Mode Channel Frequency (MHz) Conducted Output Power + Duty Factor (dBm) Antenna Gain (dBi) RSS-247 E.I.R.P Output Power (dBm) Limit (dBm) Limit (Watt) CH36 5180 12.78 5.70 18.48 23.00 0.20 CH40 5200 15.25 5.70 18.95 23.00 0.20 CH48 5240 15.19 5.70 18.89 23.00 0.20 Report No.: BTL-FICP-2-1507C117 Page 375 of 1301 Test Mode: UNII-1/TX N20 Mode Channel Frequency (MHz) FCC Part 15E Conducted Output Power (dBm) Duty Factor (dBm) FCC Part 15E Conducted Output Power + Duty Factor (dBm) Limit (dBm) Limit (Watt) CH36 5180 12.36 0.10 12.46 30.00 1.00 CH40 5200 15.06 0.10 15.16 30.00 1.00 CH48 5240 14.96 0.10 15.06 30.00 1.00 Test Mode: UNII-1/TX N20 Mode Channel Frequency (MHz) Conducted Output Power + Duty Factor (dBm) Antenna Gain (dBi) RSS-247 E.I.R.P Output Power (dBm) Limit (dBm) Limit (Watt) CH36 5180 12.46 5.70 18.16 23.00 0.20 CH40 5200 15.16 5.70 18.86 23.00 0.20 CH48 5240 15.06 5.70 18.76 23.00 0.20 Report No.: BTL-FICP-2-1507C117 Page 376 of 1301 Test Mode: UNII-1/TX N40 Mode Channel Frequency (MHz) FCC Part 15E Conducted Output Power (dBm) Duty Factor (dBm) FCC Part 15E Conducted Output Power + Duty Factor (dBm) Limit (dBm) Limit (Watt) CH38 5190 9.37 0.26 9.63 30.00 1.00 CH46 5230 8.41 0.26 8.67 30.00 1.00 Test Mode: UNII-1/TX N40 Mode Channel Frequency (MHz) Conducted Output Power + Duty Factor (dBm) Antenna Gain (dBi) RSS-247 E.I.R.P Output Power (dBm) Limit (dBm) Limit (Watt) CH38 5190 9.63 5.70 15.33 23.00 0.20 CH46 5230 8.67 5.70 14.37 23.00 0.20 Report No.: BTL-FICP-2-1507C117 Page 377 of 1301 Test Mode: UNII-2A/TX A Mode Channel Frequency (MHz) Output Power (dBm) Duty Factor (dBm) Output Power + Duty Factor (dBm) Limit (dBm) Limit (Watt) CH52 5260 15.01 0.24 15.25 24.00 0.25 CH60 5300 15.07 0.24 15.31 24.00 0.25 CH64 5320 12.58 0.24 12.82 24.00 0.25 Test Mode: UNII-2A/TX N20 Mode Channel Frequency (MHz) Output Power …

Text truncated - open the document above for the full version.