QISBM623MWiMAX CPE

WiMAX CPE Quick Start Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People’s Republic of China www.huawei.com Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd. and possible licensors. Customers shall not in any manner reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse engineer, lease, assign, or sublicense the said software, unless such restrictions are prohibited by applicable laws or such actions are approved by respective copyright holders under licenses. Trademarks and Permissions , , and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Other trademarks, product, service and company names mentioned are the property of their respective owners. Notice Some features of the product and its accessories described herein rely on the software installed, capacities and settings of local network, and may not be activated or may be limited by local network operators or network service providers. Thus the descriptions herein may not exactly match the product or its accessories you purchase. Huawei Technologies Co., Ltd. reserves the right to change or modify any information or specifications contained in this manual without prior notice or obligation. NO WARRANTY THE CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS”. EXCEPT AS REQUIRED BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS MANUAL. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO CASE SHALL HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, OR LOST PROFITS, BUSINESS, REVENUE, DATA, GOODWILL OR ANTICIPATED SAVINGS. Import and Export Regulations Customers shall comply with all applicable export or import laws and regulations and will obtain all necessary governmental permits and licenses in order to export, re-export or import the product mentioned in this manual including the software and technical data therein. i Contents Before you begin ............................................................................................................................ 1 Getting to Know Your CPE ............................................................................................................ 1 Preparing for Installation ................................................................................................................ 5 Logging In to the Web-Based Utility ............................................................................................. 7 Troubleshooting .............................................................................................................................. 8 Specifications ................................................................................................................................ 10 Warnings and Precautions .......................................................................................................... 11 1 Thank you for purchasing WiMAX CPE! Before you begin Check the following items in the product package. If you find anything missing or damaged, contact the service provider.  WiMAX CPE  Dedicated Power Adapter  Ethernet Cable  Quick Start Getting to Know Your CPE The supported functions and actual appearance of the CPE may vary with the product you purchase. The following pictures are provided for illustration purpose only. 2 Front Panel 3 Indicator Status Description WiMAX On The indicators indicate the signal strength of the WiMAX network. When all the indicators are on, it indicates that the signal strength is at the highest level. Blink  The CPE is being upgraded or scanning frequency when they blink sequentially.  The software is damaged when they blink randomly.  The CPE is in the IDLE mode when the highest indicator blinks. Off There is no WiMAX network signal. POWER On The CPE is powered on. Off The CPE is powered off. LAN On The LAN port is being used. Blink The data is being transmitted. Off The LAN port is unused. TEL On The telephone is registered. Blink The telephone is being used or the telephone is registering. Off The telephone is unregistered. WLAN On The WLAN function is enabled. Blink Data is being transmitted. Off The WLAN function is disabled. NOTE:  WiMAX: Worldwide Interoperability for Microwave Access  CPE: Customer Premises Equipment  LAN: Local Area Network  WLAN: Wireless Local Area Network 4 Rear Panel 5 Interface Description POWER The interface is used to connect to the output interface of the power adapter. TEL The interface is used to connect a telephone line. LAN The interface is used to connect the CPE to the computer. RESET Press and hold the button for one to eight seconds to restart the CPE. Press and hold the button for over eight seconds to restore the default settings of the CPE. Once you restore the default settings, all the customized data will be lost. Use this function with caution. The port is used to connect a compatible external antenna (optional accessory and sold separately). For details about how to install a compatible external antenna and enable it, refer to the Online Help in the Web-based utility. CAUTION: Do not touch the port. WLAN Press this button to enable or disable the WLAN function. Preparing for Installation Selecting a Proper Installation Position  Obstacles such as concrete or wooden walls may affect the transmission of WiMAX network signals. Therefore, install the CPE in an open space.  Keep the CPE away from any household appliance that produces a strong electr…

Text truncated - open the document above for the full version.

1(2) Huawei Technologies Co., Ltd. Attention: Application Examiner Re: Request for confidentiality Applicant: Huawei Technologies Co., Ltd. FCC ID: QISBM623M To whom it may concern, Permanent Confidentiality Request is hereby submitted by Huawei Technologies Co., Ltd to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:  Schematics  Detailed Block diagrams  Detailed Operational/Functional Description  Tune up procedure  Parts list Short-term Confidentiality Request is hereby submitted by Huawei Technologies Co., Ltd to withhold from public review for a period of 45 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 45 days from the date of Authorization:  Test setup photos  External photos  Internal photos  User manual 2(2) Rationale for request for confidentiality: Huawei Technologies Co., Ltd. has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.][Short term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] [For FCC certification; delete for TCB certification: The fee for confidentiality has been submitted along with the fee for certification.] If you have questions or need further information, please contact the undersigned. Sincerely, [Signature]: Zhang Xinghai [Title]: EMC Laboratory Manager [Company name] :Huawei Technologies Co., Ltd.

BM623m W iMAX CPE SECRET Page1，Total5 Photo Documentation of External of Product BM623m W iMAX CPE SECRET Page2，Total5 BM623m W iMAX CPE SECRET Page3，Total5 BM623m W iMAX CPE SECRET Page4，Total5 BM623m W iMAX CPE SECRET Page5，Total5

BM623m W iMAX CPE SECRET Page1，Total1 BM623m Label Location：

BM623m W iMAX CPE SECRET Page1，Total1 BM623m ID Label：

BM623m W iMAX CPE SECRET Page1，Total7 Photo Documentation of Internal of Product BM623m W iMAX CPE SECRET Page2，Total7 BM623m W iMAX CPE SECRET Page3，Total7 BM623m W iMAX CPE SECRET Page4，Total7 BM623m W iMAX CPE SECRET Page5，Total7 BM623m W iMAX CPE SECRET Page6，Total7 BM623m W iMAX CPE SECRET Page7，Total7

QISBM623M Electromagnetic Radiation Exposure Estimation Maximum Permissible Exposure (MPE) Estimation for EUT 1 Introduction HUAW EI BM623m, a WiMAX CPE, is a proprietary product developed by HUAWEI based on IEEE 802.16e-2005, and works in range of 2.496-2.69GHz, The product is composed of two PCB boards, a WiMAX and gateway board, an antenna PCB board, providing two ports and WLAN wireless downlink for the user service. 1×RJ45:10/100M LAN port; 1×RJ11:TEL port for VOIP; The W LAN module is subscriber equipment in the W LAN system, operated in CH1-CH9. It includes two modulations of type. One is DSSS and another is OFDM. Supports IEEE802.11b, g, n. 2 Limits and Guidelines on Exposure to Electromagnetic Fields According to the FCC Part 2.1091( which reference the part1.1310), we know: mobile device (transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons). And the Cellular radiotelephone service and PCS services are subject to routine environmental evaluation for RF exposure prior to equipment authorization or use if they operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5 GHz and their ERP is 3 watts or more. Uncontrolled limits are used for general public. General population/uncontrolled exposure apply in situations is which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. The exposure levels can be expressed in terms of power density, electric field strength, or magnetic field strength, as averaged over 30 minutes for the general public and 6 minutes for trained personnel. The QISBM623M Electromagnetic Radiation Exposure Estimation exposure criterion is frequency dependent, and a chart covering the range from 3 kHz to 100 GHz can be found in NCRP No.86 (references IEEE C95.1-1999). Below are the limits. Limits for Occupational/Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) 0.3-3.0 3.0-30 30-300 300-1500 15,00-100,000 614 1842/f 61.4 -- -- 16.3/f 16.3/f 0.163 -- -- (100)* (900/f 2 )* 1.0 f/300 5 Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) 0.3-1.34 1.34-30.0 30-300 300-1500 15,00-100,000 614 824/f 27.5 -- -- 1.63 2.19/f 0.073 -- -- (100)* (180/f 2 )* 0.2 f/1500 1 Power density S [mW /cm2] for controlled area at 2.5GHz (TX: 2496M-2690MHz) S=5 mW/cm 2 Power density S [mW /cm2] for uncontrolled area at 2.5GHz (TX: 2496M-2690MHz) S=1 mW/cm 2 Reference levels are provided for exposure assessment to determine whether the basic restrictions on exposure of humans to electromagnetic fields are exceeded. The basic restrictions on exposure to electromagnetic fields are based directly on established health effects and biological considerations. 3 Location of EUT The source of the radiation is mounted on terminal; generally the direction of the antenna position is uprightness tabletop. The highest level of emission would be expected in close vicinity of the antenna and in line of sight to the antenna. QISBM623M Electromagnetic Radiation Exposure Estimation 4 Prediction of the Exposure to Electromagnetic Fields Calculations can be made on a site by site basis to ensure the power density is below the limits given above, or guidelines can be done beforehand to ensure the minimum distances from the antenna is maintained through the site planning. The calculations are based on FCC OET 65 Appendix B. 4.1 Calculation of the Safe Distance Below method describes a theoretical approach to calculate possible exposure to electromagnetic radiation around a base station transceiver antenna. Precise statements are basically only possible either with measurements or complex calculations considering the complexity of the environment (e.g. soil conditions, near buildings and other obstacles) which causes reflections, scattering of electromagnetic fields. The maximum output power (given in EIRP) of a base station is usually limited by license conditions of the network operator. A rough estimation of the expected exposure in power flux density on a given point can be made with the following equation. The calculations are based on FCC OET 65 Appendix B.    )(4 )( 2 mr GWP S numeric Whereas: P = Maximum output power in W of the site G numeric = Numeric gain of the antenna relative to isotropic antenna R = distance between the antenna and the point of exposure in meters 4.2 Technical Description EIRP: =Maximum conducted power + Gain 33.60dBm =26.60dBm+7dBi TX Frequency range: 2496M-2690MHz Note: For W iMAX, the maximum conducted output power is 26.60dBm, and it’s antenna’s max gain is 7.0dBi, so we can get the max EIRP 33.60dBm. QISBM623M Electromagnetic Radiation Exposure Estimation 4.3 Estimation of compliance boundary for indoor antenna For EUT the following compliance boundary is calculated: EIRP: 2290.87mW (33.60dBm)   2 204 2290.87 S ＝0.46 mW /cm 2 Modulation MPE Limit (mW/cm 2 ) Con Output Power (mW) Duty cycle (%) Max Anna Gain (dBi) EIRP (dBm) Pd at 20cm (mW/c m2) % of limit 2496M-2690MHz 802.16e 1 457.09 1 7.0 33.60 0.46 46% The maximum power spectral density 20cm from the antenna relative to the limit is the highlighted row and the power density is 46% of the limit. The S at the position which is 20cm far from the EUT is smaller than the uncontrolled exposure limit line. So the EUT also complies with the Limits for Occupational/Controlled Exposure.

FCC RF Test Report Product Name: WiMAX CPE Model Number: BM623m Report No: SYBH(Z-RF)004112011-2001 FCC ID:QISBM623M Reliability Laboratory of Huawei Technologies Co., Ltd. Huawei Base, Bantian, Longgang District, Shenzhen 518129, P.R. China Tel: +86 755 28780808 Fax: +86 755 89652518 FCC Test Report of BM623m FCC ID:QISBM623M Security Level: Public Report No: SYBH(Z-RF)004112011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page2, Total34 Notice 1. The laboratory has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L0310. 2. The laboratory has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 97456. 3. The laboratory has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 6369A-2. 4. The test report is invalid if not marked with "exclusive stamp for the test report". 5. The test report is invalid if not marked with the stamps or the signatures of the persons responsible for performing, revising and approving the test report. 6. The test report is invalid if there is any evidence of erasure and/or falsification. 7. If there is any dissidence for the test report, please file objection to the test centre within 15 days from the date of receiving the test report. 8. Normally, the test report is only responsible for the samples that have undergone the test. 9. Context of the test report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of the laboratory. FCC Test Report of BM623m FCC ID:QISBM623M Security Level: Public Report No: SYBH(Z-RF)004112011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page3, Total34 Notice 2 Modification Information: Modification Information Modification Information 1 2 3 4 5 6 7 FCC Test Report of BM623m FCC ID:QISBM623M Security Level: Public Report No: SYBH(Z-RF)004112011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page4, Total34 REGULATION FCC CFR47 Part 2: Subpart J; 47 CFR FCC Part 27, Subpart C&M START OF TEST Nov.3, 2011 END OF TEST Nov.11, 2011 Final Judgement: Pass Approved By Nov.17, 2011 Dai Linjun Date Name Signature Reviewed By Nov.17, 2011 Cousy Xu Date Name Signature Operator Nov.17, 2011 Huang Qiuliang Date Name Signature FCC Test Report of BM623m FCC ID:QISBM623M Security Level: Public Report No: SYBH(Z-RF)004112011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page5, Total34 Contents 1 Summary .......................................................................................................................................... 6 1.1 RESULTS SUMMARY...................................................................................................................... 6 1.2 SUPPORTING STANDARDS............................................................................................................. 6 2 Product Description ........................................................................................................................ 7 2.1 PRODUCTION INFORMATION OF EUT ............................................................................................. 7 3 Test Site Description....................................................................................................................... 8 3.1 TESTING PERIOD .......................................................................................................................... 8 4 Product Description ........................................................................................................................ 9 4.1 TECHNICAL CHARACTERISTICS ...................................................................................................... 9 4.2 EUT IDENTIFICATION LIST ........................................................................................................... 11 5 Main Test Instruments .................................................................................................................. 12 6 Transmitter & Receiver Measurements ...................................................................................... 13 6.1 MAXIMUM CHANNEL POWER........................................................................................................ 14 6.2 MODULATION CHARACTERISTICS ................................................................................................. 17 6.3 OCCUPIED BANDWIDTH ............................................................................................................... 19 6.4 BAND EDGES COMPLIANCE ......................................................................................................... 21 6.5 SPURIOUS EMISSION AT ANTENNA TERMINAL .............................................................................. 24 6.6 RADIATED SPURIOUS EMISSIONS ................................................................................................ 27 6.7 FREQUENCY STABILITY ............................................................................................................... 29 7 System Measurement Uncertainty .............................................................................................. 33 8 Appendices .................................................................................................................................... 34 FCC Test Report of BM623m FCC ID:QISBM623M Security Level: Public Report No: SYBH(Z-RF)004112011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page6, Total34 1 Summary 1.1 Results Summary The table below summarizes the measurements and results for the equipment of QISBM623M W iMAX CPE-BM623M. Detailed results and descript…

Text truncated - open the document above for the full version.