QISC2801CDMA Mobile Phone

C2801 CDMA 1X Mobile Phone Copyright © 2007 Huawei Technologies Co., Ltd. and other Huawei trademarks are the trademarks or registered trademarks of Huawei Technologies Co., Ltd. in the People’s Republic of China and certain other countries. All other trademarks mentioned in this manual are the property of their respective holders. The information in this manual is subject to change without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information, and recommendations in this manual do not constitute the warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address: Huawei Industrial Base, Bantian, Longgang, Shenzhen 518129, People's Republic of China Tel: +86-755-28780808 Global Hotline: +86-755-28560808 E-mail: [email protected] Website: www.huawei.com 1 Your Phone Screen Dial/Send Key Number Keys Navigation Keys Left Soft Key Right Soft Key Earpiece Key Charger Interface Key End/Power Key Microphone 2 Keys and Functions Press... To... z View the dialled calls in the standby mode. z Make or answer a call. z Power on or off the phone (by pressing and holding it). z End a call or reject an incoming call. z Return to the home screen. Select the option displayed on the lower left corner of the screen. Select the option displayed on the lower right corner of the screen. z Display the Profiles interface (), the Messages interface ( ), the Scheduler interface (), and the Alarm interface ( ) in the standby mode. z Increase the volume ( or ) or decrease the volume ( or ) during a call. – z Enter numbers and characters. z Speed-dial phone numbers in the standby mode (by pressing and holding the 1-9 keys). z Select a submenu item labeled with the corresponding number. 3 Press... To... z Enter the * symbol. z Enable or disable the Meeting profile (by pressing and holding it). z Provide different functions according to the phone features being used. z Enter the # symbol. z Lock the keypad in the standby mode (by pressing and holding it). z Provide different functions according to the phone features being used. Screen Icons Icon Description IconDescription Network signal strengthBattery power level Calling... General profile Voice Privacy Metting profile CDMA 1X network Silent profile 3G network Outdoor profile Data service Keypad locked Roaming... Alarm clock on Message received Voice message received Emergency message received Memory for messages full 4 Menu Tree Messages Fun & Utility 1 Alarm 2 Scheduler 3 Calculator 4 Gallery 5 Gulper Profiles 1 Write Message 2 Inbox 3 Outbox 4 Draft 5 Voice Mail 6 Templates 7 Message Settings 8 Delete All Phone Book 1 General 2 Meeting 3 Silent 4 Outdoor Settings 1 Display 2 Call Settings 3 Phone Settings 4 Security 1 Search 2 Add New 3 Groups 4 Speed Dial 5 Copy All (*) 6 Delete All 7 My Phone No. 8 Memory Status Call History 1 Missed Calls 2 Received Calls 3 Dialled Calls 4 Call Duration 5 Delete All Copy All (*) If the UIM card is available, the Copy All submenu item is displayed under the Phone Book item. 5 Installing the UIM Card and Battery Consult the network operator whether a UIM card is needed. Make sure that the golden area on the UIM card is facing downwards and the cut-off edge is correctly aligned with the card holder. Removing the Battery and UIM Card Make sure that your phone is powered off. Charging the Battery 1. Connect the charger to the charger interface at the bottom of your phone. 2. Connect the charger to an AC power socket. 3. During the charging, the charging icon is displaying in animation. 4. When the charging icon becomes static, the battery is fully charged. Disconnect the charger from the AC power socket. 5. Disconnect the charger from the phone. 6 Using the Function Menu 1. In the standby mode, press (Menu) to display the Menu interface. 2. Press to scroll to a menu item. 3. Press (Select) to display the menu. 4. Display the submenu in either of the ways: z Press to scroll to a submenu item and press (Select) to display the submenu. z Press the number key corresponding to the number of a submenu to display it. 5. Press (Back) to return to the previous menu or quit the function menu. Press to return to the home screen. Making a Call 1. In the standby mode, enter a phone number. z To make an international call, press four times to enter the international long distance code of "+". Then enter the number to be dialled, in the format of "country code + region code + phone number". z To call a number with an extension, press twice to insert "P", or press three times to insert "T" between the phone number and the extension. 2. Press to dial the number. 3. Press to end the call. 7 Note z When the phone is locked, enter the lock code to unlock the phone first; otherwise, you can make emergency calls or answer calls only. z In the standby mode, press to view the dialled calls. Select a record and press to dial. z Select a contact from the phonebook and press to dial. z Select a message in the inbox and press to dial. Answering a Call When there is an incoming call, you can press or (Answer) to answer it, or press (Silence) to mute the tone, or press to reject the call. If the Any-key Answer function is enabled, you can press any key except and to answer an incoming call. Phone Lock The phone lock function protects your phone from unauthorized use. The default phone lock code is 000000. You can change it into any numeric string of four to eight digits. If the phone lock function is enabled, you need to enter the correct phone lock code when the phone is powered on or in the standby mode. PIN and PUK The personal identity number (PIN) protects your UIM card from unauthorized use. The PIN unlocking key (PUK) can unblock the 8 blocked PIN. Both PIN and PUK are delivered with the UIM card. For details, consult your service provider. If you enter wrong PINs three consecutive times, the phone asks you to enter the PUK code. If you enter wrong PUKs ten…

Text truncated - open the document above for the full version.

Huawei Technologies Co., Ltd. Address：Huawei Industrial Base,Bantian Longgang,Shenzhen 518129, P.R China Post ZIP：518129 Page ：1/1 To: CETECOM Fax : NULL From:Zhang Xinghai Fax:0086-755-89652518 Tel:0086-755-89651014 Email address: [email protected] Http: www.huawei.com Subject：Letter of Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with the Code of Federal Regulations Title 47 Section 0.457 and 0.459 pertaining to confidential material. Huawei Technologies Co., Ltd. would like the following documents regarding this submission for FCC ID: QISC2601 to be kept confidential: 1. Schematic diagram & PCB layout. 2. Block Diagram. 3. Parts list (BOM) Information. 4. Operational description. 5. Turn-up procedure The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, For and Behalf of: Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager

Huawei C2801 CDMA Handset SECRET Page1,Total 6 External Photo of Huawei C2801 Huawei C2801 CDMA Handset SECRET Page2,Total 6 Huawei C2801 CDMA Handset SECRET Page3,Total 6 Huawei C2801 CDMA Handset SECRET Page4,Total 6 Huawei C2801 CDMA Handset SECRET Page5,Total 6 Huawei C2801 CDMA Handset SECRET Page6,Total 6

Huawei C2801 CDMA Handset SECRET Page1, Total 1 Label C2801 Label Location_C2801

Huawei C2801 CDMA Handset SECRET Page1,Total 4 Internal Photo of Huawei C2801 Huawei C2801 CDMA Handset SECRET Page2,Total 4 Huawei C2801 CDMA Handset SECRET Page3,Total 4 Huawei C2801 CDMA Handset SECRET Page4,Total 4

No. 2007EEE00819 Page 31 of 75 Fig. 8 Z-Scan at power reference point (CDMA 835MHz CH777) No. 2007EEE00819 Page 32 of 75 CDMA 1X Left Tilt Middle Date/Time: 2007-3-28 18:51:00 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used (interpolated): f = 836.52 MHz; σ = 0.936 mho/m; ε r = 41.4; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 836.52 MHz Duty Cycle: 1:1 Probe: ET3DV6 - SN1736 ConvF(6.51, 6.51, 6.51) Tilt Middle/Area Scan (51x81x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (interpolated) = 0.552 mW/g Tilt Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 22.0 V/m; Power Drift = -0.168 dB Peak SAR (extrapolated) = 0.711 W/kg SAR(1 g) = 0.495 mW/g; SAR(10 g) = 0.325 mW/g Maximum value of SAR (measured) = 0.533 mW/g 0 dB = 0.533mW/g Fig. 9 Left Hand Tilt 15°CDMA 835MHz CH384 No. 2007EEE00819 Page 33 of 75 Fig. 10 Z-Scan at power reference point (CDMA 835MHz CH384) No. 2007EEE00819 Page 34 of 75 CDMA 1X Left Tilt Low Date/Time: 2007-3-28 18:21:11 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used: f = 825 MHz; σ = 0.922 mho/m; ε r = 41.5; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 824.7 MHz Duty Cycle: 1:1 Probe: ET3DV6 - SN1736 ConvF(6.51, 6.51, 6.51) Tilt Low/Area Scan (51x81x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (interpolated) = 0.627 mW/g Tilt Low/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 25.1 V/m; Power Drift = -0.159dB Peak SAR (extrapolated) = 0.794 W/kg SAR(1 g) = 0.571 mW/g; SAR(10 g) = 0.383 mW/g Maximum value of SAR (measured) = 0.610 mW/g 0 dB = 0.610mW/g Fig. 11 Left Hand Tilt 15°CDMA 835MHz CH1013 No. 2007EEE00819 Page 35 of 75 Fig. 12 Z-Scan at power reference point (CDMA 835MHz CH1013) No. 2007EEE00819 Page 36 of 75 CDMA 1X Right Cheek High Date/Time: 2007-3-28 17:42:33 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used (interpolated): f = 848.31 MHz; σ = 0.948 mho/m; ε r = 41.3; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 848.31 MHz Duty Cycle: 1:1 Probe: ET3DV6 - SN1736 ConvF(6.51, 6.51, 6.51) Cheek High/Area Scan (51x81x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (interpolated) = 1.10 mW/g Cheek High/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 24.3 V/m; Power Drift = -0.188 dB Peak SAR (extrapolated) = 1.34 W/kg SAR(1 g) = 0.976 mW/g; SAR(10 g) = 0.653 mW/g Maximum value of SAR (measured) = 1.05 mW/g 0 dB = 1.05mW/g Fig. 13 Right Hand Touch Cheek CDMA 835MHz CH777 No. 2007EEE00819 Page 37 of 75 Fig. 14 Z-Scan at power reference point (CDMA 835MHz CH777) No. 2007EEE00819 Page 38 of 75 CDMA 1X Right Cheek Middle Date/Time: 2007-3-28 17:15:22 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used (interpolated): f = 836.52 MHz; σ = 0.936 mho/m; ε r = 41.4; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 836.52 MHz Duty Cycle: 1:1 Probe: ET3DV6 - SN1736 ConvF(6.51, 6.51, 6.51) Cheek Middle/Area Scan (51x81x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (interpolated) = 0.989 mW/g Cheek Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 24.1 V/m; Power Drift = -0.200 dB Peak SAR (extrapolated) = 1.19 W/kg SAR(1 g) = 0.866 mW/g; SAR(10 g) = 0.580 mW/g Maximum value of SAR (measured) = 0.926 mW/g 0 dB = 0.926mW/g Fig.15 Right Hand Touch Cheek CDMA 835MHz CH384 No. 2007EEE00819 Page 39 of 75 Fig. 16 Z-Scan at power reference point (CDMA 835MHz CH384) No. 2007EEE00819 Page 40 of 75 CDMA 1X Right Cheek Low Date/Time: 2007-3-28 16:46:28 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used: f = 825 MHz; σ = 0.922 mho/m; ε r = 41.5; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 824.7 MHz Duty Cycle: 1:1 Probe: ET3DV6 - SN1736 ConvF(6.51, 6.51, 6.51) Cheek Low/Area Scan (51x81x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (interpolated) = 1.28 mW/g Cheek Low/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 27.1 V/m; Power Drift = -0.192 dB Peak SAR (extrapolated) = 1.47 W/kg SAR(1 g) = 1.07 mW/g; SAR(10 g) = 0.717 mW/g Maximum value of SAR (measured) = 1.15 mW/g 0 dB = 1.15mW/g Fig. 17 Right Hand Touch Cheek CDMA 835MHz CH1013 No. 2007EEE00819 Page 41 of 75 Fig. 18 Z-Scan at power reference point (CDMA 835MHz CH1013) No. 2007EEE00819 Page 42 of 75 CDMA 1X Right Tilt High Date/Time: 2007-3-28 17:54:29 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used (interpolated): f = 848.31 MHz; σ = 0.948 mho/m; ε r = 41.3; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 848.31 MHz Duty Cycle: 1:1 Probe: ET3DV6 - SN1736 ConvF(6.51, 6.51, 6.51) Tilt High/Area Scan (51x81x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (interpolated) = 0.610 mW/g Tilt High/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 21.0 V/m; Power Drift = -0.174 dB Peak SAR (extrapolated) = 0.750 W/kg SAR(1 g) = 0.545 mW/g; SAR(10 g) = 0.366 mW/g Maximum value of SAR (measured) = 0.584 mW/g 0 dB = 0.584mW/g Fig. 19 Right Hand Tilt 15°CDMA 835MHz CH777 No. 2007EEE00819 Page 43 of 75 Fig. 20 Z-Scan at power reference point (CDMA 835MHz CH777) No. 2007EEE00819 Page 44 of 75 CDMA 1X Right Tilt Middle Date/Time: 2007-3-28 17:27:40 Electronics: DAE3 Sn536 Medium: 835 HEAD Medium parameters used (interpolated): f = 836.52 MHz; σ = 0.936 mho/m; ε r = 41.4; ρ = 1000 kg/m 3 Ambient Temperature:23.3 o C Liqiud Temperature: 22.5 o C Communication System: CDMA 1X-new Frequency: 836.52 MHz Duty Cycle: 1:1 Probe: E…

Text truncated - open the document above for the full version.

No. 2007EEE00819 Page 61 of 75 ANNEX E PROBE CALIBRATION CERTIFICATE No. 2007EEE00819 Page 62 of 75 No. 2007EEE00819 Page 63 of 75 No. 2007EEE00819 Page 64 of 75 No. 2007EEE00819 Page 65 of 75 No. 2007EEE00819 Page 66 of 75 No. 2007EEE00819 Page 67 of 75 No. 2007EEE00819 Page 68 of 75 No. 2007EEE00819 Page 69 of 75 No. 2007EEE00819 Page 70 of 75 ANNEX F DIPOLE CALIBRATION CERTIFICATE No. 2007EEE00819 Page 71 of 75 No. 2007EEE00819 Page 72 of 75 No. 2007EEE00819 Page 73 of 75 No. 2007EEE00819 Page 74 of 75 No. 2007EEE00819 Page 75 of 75

No. 2007EEE00819 Page 2 of 75 Notes 1. . The test report shall be invalid if there is no “specified stamp for the test report” or the stamp of the test organization on it. 2. Copies of the test report shall be invalid if there is no “specified stamp for the test report” or the stamp of the test organization on it. 3. The test report shall be invalid if there are no signatures of the testing person, reviewing person and approving person on it. 4. The test report shall be invalid if it is altered. 5. Any demurral about the test shall be put forward to the testing organization within 15 days after the receiving of the test report. 6. This test report standalone dose not constitute or imply by its own an approval of the product by any Certification Authorities or Competent Bodies. 7. This report is only valid if complete, and test report shall not be reproduced except in full, without written approval of the laboratory. 8. This report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of Telecommunication Metrology Center of MII and the Accreditation Bodies, if it applies. Address: No. 52, Huayuan Bei Road, Haidian District, Beijing, P. R. China (Telecommunication Metrology Center of MII) Post code: 100083 Telephone: +86 10 62302041 Fax: +86 10 62304793 Web site: http://www.emcite.com E-mail: [email protected] No. 2007EEE00819 Page 3 of 75 TABLE OF CONTENT 1 COMPETENCE AND WARRANTIES....................................................................................................5 2 GENERAL CONDITIONS ....................................................................................................................... 5 3 DESCRIPTION OF EUT .......................................................................................................................... 5 3.1 ADDRESSING INFORMATION RELATED TO EUT ......................................................................................... 5 3.2 CONSTITUENTS OF EUT.............................................................................................................................6 3.3 GENERAL DESCRIPTION............................................................................................................................. 6 4 OPERATIONAL CONDITIONS DURING TEST ................................................................................. 7 4.1 SCHEMATIC TEST CONFIGURATION............................................................................................................ 7 4.2 SAR MEASUREMENT SET-UP..................................................................................................................... 8 4.3 DASY4 E-FIELD PROBE SYSTEM................................................................................................................ 9 4.4 E-FIELD PROBE CALIBRATION................................................................................................................... 9 4.5 OTHER TEST EQUIPMENT......................................................................................................................... 10 4.5.2 PHANTOM............................................................................................................................................. 10 4.6 EQUIVALENT TISSUES.............................................................................................................................. 11 4.7 SYSTEM SPECIFICATIONS......................................................................................................................... 11 5 CHARACTERISTICS OF THE TEST..................................................................................................12 5.1 APPLICABLE LIMIT REGULATIONS........................................................................................................... 12 5.2 APPLICABLE MEASUREMENT STANDARDS.............................................................................................. 12 6 LABORATORY ENVIRONMENT........................................................................................................13 7 CONDUCTED OUTPUT POWER MEASUREMENT ....................................................................... 13 7.1 SUMMARY................................................................................................................................................ 13 7.2 CONDUCTED POWER................................................................................................................................ 13 8 TEST RESULTS....................................................................................................................................... 14 8.1 DIELECTRIC PERFORMANCE.................................................................................................................... 14 8.2 SYSTEM VALIDATION...............................................................................................................................14 8.3 SUMMARY OF MEASUREMENT RESULTS.................................................................................................. 15 8.4 CONCLUSION........................................................................................................................................... 16 9 MEASUREMENT UNCERTAINTY ..................................................................................................... 16 10 MAIN TEST INSTRUMENTS ............................................................................................................. 17 11 TEST PERIOD ....................................................................................................................................... 17 12 TEST LOCATION ................................................................................................................................. 17 ANNEX A MEASUREMENT PROCESS................................................................................................…

Text truncated - open the document above for the full version.

FCC TEST REPORT OF Huawei CDMA Mobile Station M/N: C2801 May 19, 2007 Reliability Laboratory of Huawei Technologies Co., Ltd. All Right Reserved Report No: SYBH(E)05052007 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page2, Total39 Notice 1. The laboratory has obtained the accreditation of China National Accreditation Committee for Laboratories (CNAL), and accreditation number: L0310. 2. The laboratory has obtained the accreditation of THE AMERICAN ASSOCIATION FOR LABORATORY ACCREDITATION (A2LA), and Accreditation Council Certificate Number: 2174.01. 3. The laboratory has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 97456. 4. The laboratory also has been listed by the VCCI to perform EMC measurements. The accreditation number is C1758, R1672, and T153. 5. The test report is invalid if not marked with "exclusive stamp for the test report". 6. Any copy of the test report is invalid if not re-marked with the "exclusive stamp for the test report". 7. The test report is invalid if not marked with the stamps or the signatures of the persons responsible for performing, revising and approving the test report. 8. The test report is invalid if there is any evidence of erasure and/or falsification. 9. If there is any dissidence for the test report, please file objection to the test centre within 15 days from the date of receiving the test report. 10. Normally, the test report is only responsible for the samples that have undergone the test. 11. Context of the test report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of the laboratory. Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page3, Total39 REPORT ON FCC Test of Huawei CDMA Mobile Station M/N: C2801 Report No: SYBH(E)05052007 REGULATION FCC CFR47 Part 2: Subpart J; FCC CFR47 Part 22: Subpart H; FCC CFR47 Part 15: Subpart B; CONCLUSION There are 9 items need to be tested, 9 items have been tested. The sample of the model completely meets the requirements Final Judgement: Pass General Manager 2007.05.21 Guo Xiaoqi Date Name signature Technical Responsibility For Area of Testing 2007.05.20 Zhang Xinghai Date Name signature Test Lab Engineer 2007.05.19 HuJun Date Name signature Huawei Technologies Co Ltd Huawei Industrial Base, Bantian Longgang Shenzhen 518128, P.R China Tel: +86 755 89651014 Fax: +86 755 89652518 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page4, Total39 Contents 1 Summary.................................................................................................................................................... 5 2 Product Description................................................................................................................................6 2.1 PRODUCTION INFORMATION................................................................................................................... 6 2.2 MODIFICATION INFORMATION.................................................................................................................. 6 3 Test Site Description................................................................................................................................. 7 3.1 TESTING PERIOD................................................................................................................................... 7 3.2 GENERAL SET UP DESCRIPTION............................................................................................................. 7 4 Product Description.................................................................................................................................. 8 4.1 TECHNICAL CHARACTERISTICS............................................................................................................... 8 4.2 EUT IDENTIFICATION LIST.................................................................................................................... 10 5 Main Test Instruments............................................................................................................................. 11 6 Transmitter Measurements..................................................................................................................... 12 6.1 EFFECTIVE RADIATED POWER OF TRANSMITTER (ERP)......................................................................... 12 6.2 CONDUCTED OUTPUT POWER............................................................................................................... 15 6.3 MODULATION CHARACTERISTICS.......................................................................................................... 17 6.4 OCCUPIED BANDWIDTH........................................................................................................................ 19 6.5 BAND EDGES COMPLIANCE.................................................................................................................. 22 6.6 SPURIOUS EMISSION AT ANTENNA TERMINAL........................................................................................ 24 6.7 RADIATED SPURIOUS RADIATION.......................................................................................................... 26 6.8 FREQUENCY STABILITY........................................................................................................................ 30 7 EMC Test.................................................................................................................................................. 34 7.1 CONDUCTED EMISSION AT POWER PORT.............................................................................................. 34 7.2 RADIATED EMISSION OF ENCLOSURE IN IDEAL MODE.................…

Text truncated - open the document above for the full version.

FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page1, Total3 Appendix A Modulation Characteristics According to FCC Part 2.1047 & Part22 Subpart H FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page2, Total3 Channel 283TM1 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page3, Total3 Channel 283TM3

FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page1, Total5 Appendix B Occupied Bandwidth According to FCC Part 2.1049 & Part 22 Subpart H FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page2, Total5 Channel 1013TM1 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page3, Total5 Channel 1013TM3 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page4, Total5 Channel 777TM1 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page5, Total5 Channel 777TM3

FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page1, Total5 Appendix C Band Edges Compliance According to FCC Part 2.1051 & 22.917 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page2, Total5 TM1 Left Edge Channel 1013 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page3, Total5 Right Edge Channel 777 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page4, Total5 TM3 Left Edge Channel 1013 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of HUAWEI. No Distribution without Permission Page5, Total5 Right Edge Channel 777

FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page1, Total13 Appendix D Spurious Emission at Antenna Terminal According to FCC Part 2.1051 & 22.917 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page2, Total13 TM1 Channel 1013 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page3, Total13 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page4, Total13 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page5, Total13 Channel 777 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page6, Total13 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page7, Total13 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page8, Total13 TM3 Channel 1013 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page9, Total13 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page10, Total13 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distribution without Permission Page11, Total13 Channel 777 FCC ID: QISC2801 Report No: SYBH(E)05052007 Confidential Information of Huawei. No Distri…

Text truncated - open the document above for the full version.