QISEM820WHSPA+ Module

Copyright © 2008 Huawei Technologies Co., Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied. i Table of Contents Getting to Know the EM820W.................................................................. 3 Requirements for the PC......................................................................... 4 Preparing the EM820W........................................................................... 4 Installation Guide.................................................................................. 5 2 Thank you for purchasing Huawei EM820W HSPA+ Embedded PC Module. Note: „ This manual briefly describes the preparation, the process for installing/uninstalling, and safety precautions for using Huawei EM820W HSPA+ Embedded PC Module (hereinafter referred to as the EM820W). „ You are recommended to read the manual before using the EM820W. „ The signal strength and the transmission rate are affected by the actual environment. Getting to Know the EM820W The following figure shows the appearance of the EM820W. The actual product may differ. n Mini PCI Express connector It is used to connect the EM820W to the WWAN Mini PCI Express interface of the PC. o Screw holes They are used to fix the EM820W on the main board of the PC with screws. 3 4 p Antenna interfaces They are used to connect antennas. Requirements for the PC To use the EM820W, the PC must meet the following requirements: „ WWAN Mini PCI Express interface. „ Windows 2000 SP4, Windows XP SP2, and Windows Vista „ The hardware of your PC must meet or exceed the recommended system requirements for the installed version of OS. „ Display resolution: 800 × 600 or above. „ The antenna gain：850M<4.28dBi，1900M<3.0 dBi Preparing the EM820W Locate the WWAN Mini PCI Express interface on the main board of the PC. Find the main antenna and the auxiliary antenna. If a USIM/SIM card is provided by your service provider, insert the USIM/SIM card into the USIM/SIM card slot on the main board of the PC. Note: „ In certain cases, your PC may be disassembled only by the professionals. „ Before you install the EM820W onto the main board of the PC, consult the PC manufacturer or read the user manual of the PC. Installation Guide Installing the EM820W onto the Main Board of the PC 1. Insert the Mini PCI Express connector of the EM820W into the WWAN Mini PCI Express interface on the main board of the PC. 2. Press downwards to fix the EM820W in the module slot. 5 3. Use a screwdriver to fix the EM820W onto the main board of the PC with two screws provided in the EM820W packing box. 6 4. Insert the connector of the main antenna into the MAIN antenna interface (M) of the EM820W according to the indication on the label of the EM820W. Insert the connector of the auxiliary antenna into the AUX antenna interface (A) of the EM820W in the same way. Note: „ Insert the antenna connectors vertically into the antenna interfaces of the EM820W. „ Do not pinch the antenna cable or damage the connectors. Otherwise, the wireless performance of the EM820W may be reduced or the EM820W cannot work normally. „ Ensure that the antenna cables are routed through the channel in the frame of the PC and do not lay across the raised edges of the frame. 7 Removing the EM820W from the Main Board of the PC 1. Disconnect the antenna cables from the EM820W. You can lift the connectors with a small screwdriver. 2. Remove the two screws with the screwdriver. 8 3. Slide backwards the two clips to release the EM820W from the slot. Then, lift up the EM820W. Installing the EM820W Software A disk is provided in the EM820W packing box. The disk contains the management program and the driver of the EM820W. 1. Insert the disk into the disk drive of the PC. 2. The OS automatically starts the installation wizard. Note: If the auto-run program does not respond, find the AutoRun.exe file under the disk path. Then double-click AutoRun.exe to run the program. 3. Follow the prompts of the installation wizard. 4. After the program is installed, the shortcut icon of the management program is displayed on the desktop. 9 10 Uninstalling the Management Program 1. Choose Start > Control Panel. 2. Find the management program, and click Add/Remove Program to uninstall the management program. Note: It is recommended to restart the PC after the uninstallation to ensure that the management program is completely uninstalled. *

Copyright © Huawei Technologies Co., Ltd. 2009. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd and possible licensors. Customers shall not in any manner reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse engineer, lease, assign, or sublicense the said software, unless such restrictions are prohibited by applicable laws or such actions are approved by respective copyright holders under licenses. Trademarks and Permissions , , and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Other trademarks, product, service and company names mentioned are the property of their respective owners. Notice Some features of the product and its accessories described herein rely on the software installed, capacities and settings of local network, and may not be activated or may be limited by local network operators or network service providers, thus the descriptions herein may not exactly match the product or its accessories you purchase. Huawei Technologies Co., Ltd reserves the right to change or modify any information or specifications contained in this manual without prior notice or obligation. NO WARRANTY THE CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS”. EXCEPT AS REQUIRED BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS MANUAL. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO CASE SHALL HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, OR LOST PROFITS, BUSINESS, REVENUE, DATA, GOODWILL OR ANTICIPATED SAVINGS. Import and Export Regulations Customers shall comply with all applicable export or import laws and regulations and will obtain all necessary governmental permits and licenses in order to export, re-export or import the product mentioned in this manual including the software and technical data therein. Warnings and Precautions This section contains important information pertaining to the operating instructions of your device. It also contains information about how to use your device safely. Read this information carefully before using the device. Electronic Device Do not use your device if using the device is prohibited. Do not use the device when using the device causes danger or interference with electronic devices. Medical Device z Follow rules and regulations set forth by hospitals and health care facilities. Do not use your device when using the device is prohibited. z Some wireless devices may affect the performance of hearing aids or pacemakers. For any such problems, consult your service provider. z If you are using an electronic medical device, consult the doctor or the device manufacturer to confirm whether radio waves affect the operation of this device. Potentially Explosive Atmosphere Do not use your device in any area with a potentially explosive atmosphere, and comply with all signs and instructions. Areas that may have potentially explosive atmospheres include the areas where you would normally be advised to turn off your vehicle engine. Triggering of sparks in such areas could cause an explosion or a fire, resulting in bodily injuries or even deaths. Do not use your device at refueling points such as service stations. Comply with restrictions on the use of radio equipment in fuel depots, storage, and distribution areas, and chemical plants. In addition, adhere to restrictions in areas where blasting operations are in progress. Before using the device, watch out for areas that have potentially explosive atmospheres that are often, but not always, clearly marked. Such locations include areas below the deck on boats, chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust, or metal powders. Ask the manufacturers of vehicles using liquefied petroleum gas (such as propane or butane) whether this device can be safely used in their vicinity. Traffic Security z Observe local laws and regulations while using the device. To prevent accidents, do not use your wireless device while driving. z RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer. z In a motor vehicle, do not place the device over the air bag or in the air bag deployment area. Otherwise, the device may hurt you owing to the strong force when the air bag inflates. z Do not use your device while flying in an aircraft and before boarding an aircraft. Using wireless devices in an aircraft may cause danger to the operation of the aircraft and disrupt the wireless telephone network. It may also be considered illegal. Operating Environment z Do not use the device in dusty, damp, and dirty places or places with magnetic fields. Otherwise, it may result in malfunction of the circuit. z On a stormy day with thunder, do not use your device when it is being charged, to prevent any danger caused by lightning. z While using the device, observe the local laws and regulations, and respect others' privacy and legal rights. Safety of Children Comply with all precautions with regard to children's safety. Letting the child play with your device or its accessories, which may include parts that can be detached from the device, may be dangerous, as it may present a choking hazard. Ensure that small children are kept away from the device and accessories. Accessories Use the accessories delivered only by the manufacturer. Using accessories of other manufacturers or vendors with this device model may invalidate any approval or warranty applicable to the device, result in the non-operation of the d…

Text truncated - open the document above for the full version.

Huawei Technologies Co., Ltd. Address：Huawei Industrial Base,Bantian Longgang,Shenzhen 518129, P.R ChinaPost ZIP：518129 Page ：1/1 To: CETECOM Fax : NULL From:Zhang Xinghai Fax:0086-755-89652518 Tel:0086-755-89651014 Email address: [email protected] Http: www.huawei.com Subject：Letter of Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with the Code of Federal Regulations Title 47 Section 0.457 and 0.459 pertaining to confidential material. Huawei Technologies Co., Ltd. would like the following documents regarding this submission for FCC ID: QISEM820W to be kept confidential: 1. Schematic diagram . 2. Block Diagram. 3. Parts list (BOM) Information. 4. Operational description. 5. Tune-up procedure The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, For and Behalf of: Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager

Huawei Technologies Co., Ltd. Administration Building, Huawei Base, Bantian, Longgang District, Shenzhen 518129 P.R.C. +86 755 28780808 www.huawei.com Huawei internal reference RCT-US-01-01 USA FCC Short Term Confidentiality Request template Effective date: 2007-01-06 Version 1.1 Short Term Confidentiality Request 2010-12-14 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: SHORT-TERM Confidentiality Request for FCC ID: QISEM820W Product Name: HSPA+ Module Product Model: EM820W To whom maybe concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, Huawei Technologies Co., Ltd requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 90 days: 1. External Photos 2. Internal Photos 3. Test Setup Photos 4. Users Manual The applicant also acknowledges that they will also provide appropriate notice to CETECOM should either of the following occur: A) If the applicant requires additional 45 day extension periods they will notify CETECOM with a new request letter at least 7 days prior to the short-term confidentiality expiration date-[Note: up to maximum of 3 extensions only are allowed], or b) Immediately notify CETECOM in the event the information regarding the product of the product is made available to the public. CETECOM will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely,

EM820W SECRET Page1,Total 4 External Photos of EM820W EM820W SECRET Page2,Total 4 EM820W SECRET Page3,Total 4 EM820W SECRET Page4,Total 4

EM820W SECRET Page1,Total 1 ID Label Location_EM820W

EM820W SECRET Page1,Total 3 Internal Photos of EM820W EM820W SECRET Page2,Total 3 EM820W SECRET Page3,Total 3

EM820W Electromagnetic Radiation Exposure Estimation 1 Maximum Permissible Exposure (MPE) Estimation for EM820W 1 Introduction EM820W HSPA+/HSUPA/HSDPA/WCDMA/EDGE/GPRS/GSM dual mode module is subscriber equipment in the UMTS/GSM system. EM820W implements such functions as RF signal receiving/transmitting, HSPA+/WCDMA and EDGE/GPRS/GSM protocol processing, data service etc. Externally it provides PCIE MINI CARD interface (to connect to the notebook etc.),. EM820W has no internal antenna. 2 Limits and Guidelines on Exposure to Electromagnetic Fields According to the FCC Part 2.1091( which reference the part1.1310), we know: mobile device (transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons). And the Cellular radiotelephone service and PCS services are subject to routine environmental evaluation for RF exposure prior to equipment authorization or use if they operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5 GHz and their ERP is 3 watts or more. Uncontrolled limits are used for general public. General population/uncontrolled exposure apply in situations is which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. The exposure levels can be expressed in terms of power density, electric field strength, or magnetic field strength, as averaged over 30 minutes for the general public and 6 minutes for trained personnel. The exposure criterion is frequency dependent, and a chart covering the range from 3 kHz to 100 GHz can be found in NCRP No.86 (references IEEE C95.1-1999). Below are the limits. Limits for Occupational/Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) EM820W Electromagnetic Radiation Exposure Estimation 2 0.3-3.0 3.0-30 30-300 300-1500 15,00-100,000 614 1842/f 61.4 -- -- 16.3/f 16.3/f 0.163 -- -- (100)* (900/f 2 )* 1.0 f/300 5 Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) 0.3-1.34 1.34-30.0 30-300 300-1500 15,00-100,000 614 824/f 27.5 -- -- 1.63 2.19/f 0.073 -- -- (100)* (180/f 2 )* 0.2 f/1500 1 Power density S [mW/cm2] for controlled area at 850 MHz ，(TX: 824MHz – 849MHz) 75.2 300 824 300 )( === MHzf S mW/cm 2 Power density S [mW/cm2] for uncontrolled area at 850 MHz 55.0 1500 824 1500 )( === MHzf S mW/cm 2 Power density S [mW/cm2] for uncontrolled area at 1900/2400 MHz S=1 mW/cm 2 Reference levels are provided for exposure assessment to determine whether the basic restrictions on exposure of humans to electromagnetic fields are exceeded. The basic restrictions on exposure to electromagnetic fields are based directly on established health effects and biological considerations. 3 Location of EUT The source of the radiation is mounted on terminal; generally the direction of the antenna position is uprightness tabletop. The highest level of emission would be expected in close vicinity of the antenna and in line of sight to the antenna. 4 Prediction of the Exposure to Electromagnetic Fields Calculations can be made on a site by site basis to ensure the power density is below the limits given above, or guidelines can be done beforehand to ensure the minimum distances EM820W Electromagnetic Radiation Exposure Estimation 3 from the antenna is maintained through the site planning. The calculations are based on FCC OET 65 Appendix B. 4.1 Calculation of the Safe Distance Below method describes a theoretical approach to calculate possible exposure to electromagnetic radiation around a base station transceiver antenna. Precise statements are basically only possible either with measurements or complex calculations considering the complexity of the environment (e.g. soil conditions, near buildings and other obstacles) which causes reflections, scattering of electromagnetic fields. The maximum output power (given in EIRP) of a base station is usually limited by license conditions of the network operator. A rough estimation of the expected exposure in power flux density on a given point can be made with the following equation. The calculations are based on FCC OET 65 Appendix B. π∗∗ ∗ = )(4 )( 2 mr GWP S numeric Whereas: P = Maximum output power in W of the site G numeric = Numeric gain of the antenna relative to isotropic antenna R = distance between the antenna and the point of exposure in meters 4.2 Technical Description EM820W Technical Specification: Cellular Band Power at antenna connector BTS: 34.65 dBm(GSM850)/25.00dBm(WCDMA850) Antenna-cable attenuation: 0 dB Input power to antenna: 34.65 dBm（2.92W）(GSM850)/ 25.00 dBm（0.32W） (WCDMA850) Antenna gain: 4.28 dBi (2.68) PCS Band EM820W Electromagnetic Radiation Exposure Estimation 4 Power at antenna connector BTS: 31.98 dBm(GSM1900)/ 26.47 dBm(WCDMA1900) Antenna-cable attenuation: 0 dB Input power to antenna: 31.98 dBm （1.58W）(GSM1900)/ 26.47 dBm（0.443W） (WCDMA1900) Antenna gain:3dBi (2.0) 4.3 Estimation of compliance boundary for indoor antenna 1) Cellular Band : GSM850 For the final determination of the compliance boundary the model for far-field calculation is used since this overestimates the field strength in the near-field region. Thus the calculated compliance boundary should be rather more conservative and on the safe side. For EUT the following compliance boundary is calculated: Compliance boundary For GSM 850MHz band: When r=20cm and GSM only use one timeslot, so π∗∗ ∗ = )(4*8 )( 2 timeslotone mr GWP S numeric π∗∗ = 2 timeslotone 204*8 68.2*2920 S…

Text truncated - open the document above for the full version.

FCC RF Test Report Product Name: HSPA+ Module Model Number: EM820W Report No: SYBHZ(R)E045112010EB-2 FCC ID: QISEM820W IC ID: 6369A-EM820W Reliability Laboratory of Huawei Technologies Co., Ltd. Huawei Base, Bantian, Longgang District, Shenzhen 518129, P.R. China Tel: +86 755 28780808 Fax: +86 755 89652518 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total35 Notice 1. The laboratory has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L0310. 2. The laboratory has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 97456. 3. The laboratory has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 6369A-1. 4. The test report is invalid if not marked with "exclusive stamp for the test report". 5. The test report is invalid if not marked with the stamps or the signatures of the persons responsible for performing, revising and approving the test report. 6. The test report is invalid if there is any evidence of erasure and/or falsification. 7. If there is any dissidence for the test report, please file objection to the test centre within 15 days from the date of receiving the test report. 8. Normally, the test report is only responsible for the samples that have undergone the test. 9. Context of the test report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of the laboratory. FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Notice 2 Modification Information: Modification Information 1 2 3 4 5 6 Modification Information 7 Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total35 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W REGULATION FCC CFR47 Part 2: Subpart J; FCC CFR47 Part 22 : Subpart H; RSS-Gen Issue 2 June 2007 RSS-132 Issue 2 September 2005 START OF TEST Nov.23, 2010 END OF TEST Nov.25, 2010 Final Judgement: Pass Approved By Nov.27, 2010 Liuchunlin Date Name Signature Reviewed By Nov.27, 2010 Chenxiaohong Date Name Signature Operator Nov.27, 2010 Zhangting Date Name Signature Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Written Permission Page4, Total35 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Written Permission Page5, Total35 Contents 1 Summary.................................................................................................................................................... 6 2 Product Description.................................................................................................................................. 7 2.1 PRODUCTION INFORMATION................................................................................................................... 7 2.2 MODIFICATION INFORMATION.................................................................................................................. 7 3 Test Site Description................................................................................................................................. 8 3.1 TESTING PERIOD................................................................................................................................... 8 3.2 GENERAL SET UP DESCRIPTION............................................................................................................. 8 4 Product Description.................................................................................................................................. 9 4.1 TECHNICAL CHARACTERISTICS............................................................................................................... 9 4.2 EUT IDENTIFICATION LIST.................................................................................................................... 11 5 Main Test Instruments............................................................................................................................. 12 6 Transmitter Measurements..................................................................................................................... 13 6.1 EFFECTIVE RADIATED POWER OF TRANSMITTER (ERP)......................................................................... 13 6.2 CONDUCTED POWER OF TRANSMITTER................................................................................................. 17 6.3 MODULATION CHARACTERISTICS.......................................................................................................... 20 6.4 OCCUPIED BANDWIDTH........................................................................................................................ 22 6.5 BAND EDGES COMPLIANCE.................................................................................................................. 25 6.6 SPURIOUS EMISSION AT ANTENNA TERMINAL........................................................................................ 27 6.7 FREQUENCY STABILITY........................................................................................................................ 30 7 System Measurement Uncertainty......................................................................................................... 34 8 Appendices.............................................................................................................................................. 35 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei.…

Text truncated - open the document above for the full version.

FCC Test Report of EM820W FCC ID: QISEM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Permission Page1, Total4 Appendix A Modulation Characteristics According to FCC Part 2.1047 & Part22 Subpart H FCC Test Report of EM820W FCC ID: QISEM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Permission Page2, Total4 Channel 192（TM1:GPRS/GSM） FCC Test Report of EM820W FCC ID: QISEM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Permission Page3, Total4 Channel 192（TM2:EDGE） FCC Test Report of EM820W FCC ID: QISEM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of Huawei. No Distribution without Permission Page4, Total4 Channel 4182（TM3: WCDMA） FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of HUAWEI. No Distribution without Permission Page1, Total10 Appendix B Occupied Bandwidth According to FCC Part 2.1049 & Part 22 Subpart H & RSS-132 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of HUAWEI. No Distribution without Permission Page2, Total10 Channel 128（TM1:GPRS/GSM） A * * RBW 3 kHz VBW 10 kHz SWT 115 ms Offset 7.1 dB LVL Ref 35 dBmAtt 35 dB Center 824.2 MHzSpan 1 MHz100 kHz/ *1 AV MAXH -60 -50 -40 -30 -20 -10 0 10 20 30 1 Marker 1 [T1 ] 23.26 dBm 824.148717949 MHz OBW246.794871795 kHz T1 Temp 1 [T1 OBW] 10.89 dBm 824.076602564 MHz T2 Temp 2 [T1 OBW] 7.27 dBm 824.323397436 MHz Date: 25.NOV.2010 07:47:45 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of HUAWEI. No Distribution without Permission Page3, Total10 Channel 128（TM2:EDGE） A * * RBW 3 kHz VBW 10 kHz SWT 115 ms Offset 7.1 dB LVL Ref 35 dBmAtt 35 dB Center 824.2 MHzSpan 1 MHz100 kHz/ *1 AV MAXH -60 -50 -40 -30 -20 -10 0 10 20 30 1 Marker 1 [T1 ] 18.05 dBm 824.220833333 MHz OBW243.589743590 kHz T1 Temp 1 [T1 OBW] 1.88 dBm 824.079807692 MHz T2 Temp 2 [T1 OBW] 1.45 dBm 824.323397436 MHz Date: 25.NOV.2010 08:08:27 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of HUAWEI. No Distribution without Permission Page4, Total10 Channel 4132（TM3: WCDMA） A * * RBW 50 kHz VBW 500 kHz SWT 5 ms Offset 7.1 dB LVL Ref 35 dBmAtt 35 dB Center 826.4 MHzSpan 10 MHz1 MHz/ *1 RM MAXH -60 -50 -40 -30 -20 -10 0 10 20 30 1 Marker 1 [T1 ] 14.74 dBm 826.992948718 MHz OBW 4.182692308 MHz T1 Temp 1 [T1 OBW] 6.32 dBm 824.316666667 MHz T2 Temp 2 [T1 OBW] 5.56 dBm 828.499358974 MHz Date: 25.NOV.2010 08:13:07 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of HUAWEI. No Distribution without Permission Page5, Total10 Channel 192（TM1:GPRS/GSM） A Att 35 dB * * RBW 3 kHz VBW 10 kHz SWT 115 msRef 35 dBm Offset 7.1 dB LVL Center 837 MHzSpan 1 MHz100 kHz/ *1 AV MAXH -60 -50 -40 -30 -20 -10 0 10 20 30 1 Marker 1 [T1 ] 23.72 dBm 837.017628205 MHz OBW245.192307692 kHz T1 Temp 1 [T1 OBW] 8.25 dBm 836.878205128 MHz T2 Temp 2 [T1 OBW] 8.62 dBm 837.123397436 MHz Date: 25.NOV.2010 07:47:59 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidential Information of HUAWEI. No Distribution without Permission Page6, Total10 Channel 192（TM2:EDGE） A Att 35 dB * * RBW 3 kHz VBW 10 kHz SWT 115 msRef 35 dBm Offset 7.1 dB LVL Center 837 MHzSpan 1 MHz100 kHz/ *1 AV MAXH -60 -50 -40 -30 -20 -10 0 10 20 30 1 Marker 1 [T1 ] 18.83 dBm 837.038461538 MHz OBW243.589743590 kHz T1 Temp 1 [T1 OBW] 2.34 dBm 836.878205128 MHz T2 Temp 2 [T1 OBW] 5.77 dBm 837.121794872 MHz Date: 25.NOV.2010 08:08:41 FCC Test Report of EM820W FCC ID: QISEM820W IC ID: 6369A-EM820W Report No: SYBHZ(R)E045112010EB-2 Confidenti…

Text truncated - open the document above for the full version.