QISMU509GHSDPA Module

Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd and possible licensors. Customers shall not in any manner reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse engineer, lease, assign, or sublicense the said software, unless such restrictions are prohibited by applicable laws or such actions are approved by respective copyright holders under licenses. Trademarks and Permissions , , and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Other trademarks, product, service and company names mentioned are the property of their respective owners. Notice Some features of the product and its accessories described herein rely on the software installed, capacities and settings of local network, and may not be activated or may be limited by local network operators or network service providers, thus the descriptions herein may not exactly match the product or its accessories you purchase. Huawei Technologies Co., Ltd reserves the right to change or modify any information or specifications contained in this manual without prior notice or obligation. NO WARRANTY THE CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS”. EXCEPT AS REQUIRED BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS MANUAL. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE L AW, IN NO CASE SHALL HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, OR LOST PROFITS, BUSINESS, REVENUE, DATA, GOODWILL OR ANTICIPATED SAVINGS. Import and Export Regulations Customers shall comply with all applicable export or import laws and regulations and will obtain all necessary governmental permits and licenses in order to export, re-export or import the product mentioned in this manual including the software and technical data therein. i Contents Getting to Know the MU509 ..................................................................................................................................... 1 PCB Design ........................................................................................................................................................................ 3 Assembly............................................................................................................................................................................. 5 Safety Information ......................................................................................................................................................... 8 1 Thank you for purchasing HUAWEI MU509-g HSDPA Module (hereinafter referred to as the MU509) Note:  This manual briefly describes the preparation, the process for PCB Design, Assembly and safety precautions.  You are recommended to read the manual before using the MU509. Getting to Know the MU509 The package of the LGA module is 116 pin LGA with a dimension of 30 mm × 30 mm × 2.5 mm and the pitch of 1.5 mm. It is applied to the user interface board, and can be used as a wireless terminal in a network environment. 2 3 PCB Design CB Pad Design To achieve high efficiency of the production and solder joints of high reliability, it is recommended that the PCB pad size be designed as follows: the size of the middle region is the same as the pad size of the product package; other pads are 0.05 mm larger than the unilateral pad of the product package. For details, see the following figure: 4 Requirements on PCB Layout  Other devices must be located more than 3 mm away from the LGA module. It is recommended to be 5 mm. The minimum distance between the LGA module and the PCB edge is 1.5 mm.  When the PCB layout is double sided, it is recommended that the LGA module be placed on the second side for assembly. 5 Design of Solder Mask The PCB pad design can be solder mask defined (SMD), or non-solder mask defined (NSMD). NSMD is recommended. In addition, the solder mask of the NSMD pad design is larger than the pad so the reliability of the solder joint can be improved. The solder mask must be 100 um to150 um larger than the pad, that is, the single side of the solder mask must be 50 um to 75 um larger than the pad. The specific size depends on the processing capability of the PCB manufacturer. Assembly Stencil Design It is recommended that the stencil for the LGA module be 0.12 mm in thickness. For the stencil design, see the following figure: 6 Reflow Profile For the soldering temperature of the LGA module, see the following figure: 7 Reflow parameters: Preheat zone (40–150°C) Time: 60–120sec Heating rate: 0.5–2°C/sec Soak zone (150-200°C) Time: 60–120sec Heating rate: <1.0°C/sec Reflow zone (> 217°C) Time: 30–90sec Peak reflow temperature: 230–260°C Cooling zone Cooling rate: 1°C/sec ≤ Slope ≤ 4°C/sec 8 Safety Information Read the safety information carefully to ensure the correct and safe use of your wireless device. Interference Do not use your wireless device if using the device is prohibited or when it causes danger or interference with electric devices. Medical Device  Do not use your wireless device and follow the rules and regulations set forth by the hospitals and health care facilities.  Some wireless devices may affect the performance of the hearing aids. For any such problems, consult your service provider.  If you are using an electronic medical device, consult the doctor or device manufacturer to confirm whether the radio wave affects the operation of this device. Area with Inflammables and Explosives To prevent explosions and fires in areas that are st…

Text truncated - open the document above for the full version.

Huawei Technologies Co., Ltd. Address:Huawei Industrial Base,Bantian Longgang,Shenzhen, P.R China Post ZIP：518129 Page ：1/1 To: CETECOM Fax : NULL From:Zhang Xinghai Fax:0086-755-89652518 Tel:0086-755-89651014 Email address: [email protected] Http: www.huawei.com Subject：Letter of Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with the Code of Federal Regulations Title 47 Section 0.457 and 0.459 pertaining to confidential material. Huawei Technologies Co., Ltd. would like the following documents regarding this submission for FCC ID: QISMU509G to be kept confidential: 1. Schematic diagram . 2. Block Diagram. 3. Parts list (BOM) Information. 4. Operational description. 5. Tune-up procedure The above material contains trade secrets or technical data, which would customarily be guarded from competitors. W e do not want these documents to be accessible to the general public. Sincerely, For and Behalf of: Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager

Huawei Technologies Co., Ltd. Administration Building, Huawei Base, Bantian, Longgang District, Shenzhen 518129 P.R.C. +86 755 28780808 www.huawei.com Huawei internal reference RCT-US-01-01 USA FCC Short Term Confidentiality Request template Effective date: 2007-01-06 Version 1.1 Short Term Confidentiality Request 2011-09-30 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: SHORT-TERM Confidentiality Request for FCC ID: QISMU509G Product Name: HSDPA Module Product Model: MU509-g To whom maybe concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, Huawei Technologies Co., Ltd requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 days: 1. External Photos 2. Internal Photos 3. Test Setup Photos 4. Users Manual The applicant also acknowledges that they will also provide appropriate notice to CETECOM should either of the following occur: A) If the applicant requires additional 45 day extension periods they will notify CETECOM with a new request letter at least 7 days prior to the short-term confidentiality expiration date-[Note: up to maximum of 3 extensions only are allowed], or b) Immediately notify CETECOM in the event the information regarding the product of the product is made available to the public. CETECOM will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely,

Huawei Technologies Co., Ltd. Federal Communication Commission Equipment Authorization Devision, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 2011-09-29 TO WHOM IT MAY CONCERN Request for Single Limited Modular Approval FCC ID: QISMU509G Huawei Technologies Co., Ltd. hereby requests a Single Limited Modular Approval for its application with FCC ID: QISMU509G granted on 2011-09-29 according to KDB 996369 D01 Transmitter Module Equipment Authorization Guide 1) The module has its own RF shielding 2) The module has digital input buffer 3) The module has its own power supply regulation 4) The module has been tested with its built-in fixed antenna 5) The module will be labelled with its own FCC ID number 6) The module complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions 7) The module shall be approved for mobile RF Exposure conditions only. If you have any questions, please feel free to contact us at the address shown below Sincerely, Zhang Xinghai EMC Laboratory Manager For and Behalf of: Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang, Shenzhen, P.R China 0086-755-89651014

MU509-g SECRET Page1, Total4 External Photos of MU509-g MU509-g SECRET Page2, Total4 MU509-g SECRET Page3, Total4 MU509-g SECRET Page4, Total4

MU509-g SECRET Page1, Total1 ID Label MU509-g MU509-g SECRET Page1, Total1 ID Label Location_ MU509-g

MU509-g SECRET Page1, Total2 Internal Photos of MU509-g MU509-g SECRET Page2, Total2

MU509-g Electromagnetic Radiation Exposure Estimation 1 Maximum Permissible Exposure (MPE) Estimation for MU509-g 1 Introduction MU509-g HSDPA/W CDMA/EDGE/GPRS/GSM dual mode W ireless Module is subscriber equipment in the UMTS/GSM system. MU509-g implement such functions as RF signal receiving/transmitting, HSDPA/W CDMA and EDGE/GPRS/GSM protocol processing, data service etc. Externally it provides LGA interface. 2 Limits and Guidelines on Exposure to Electromagnetic Fields According to the FCC Part 2.1091( which reference the part1.1310), we know: mobile device (transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons). And the Cellular radiotelephone service and PCS services are subject to routine environmental evaluation for RF exposure prior to equipment authorization or use if they operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5 GHz and their ERP is 3 watts or more. Uncontrolled limits are used for general public. General population/uncontrolled exposure apply in situations is which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. The exposure levels can be expressed in terms of power density, electric field strength, or magnetic field strength, as averaged over 30 minutes for the general public and 6 minutes for trained personnel. The exposure criterion is frequency dependent, and a chart covering the range from 3 kHz to 100 GHz can be found in NCRP No.86 (references IEEE C95.1-1999). Below are the limits. Limits for Occupational/Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) MU509-g Electromagnetic Radiation Exposure Estimation 2 0.3-3.0 3.0-30 30-300 300-1500 15,00-100,000 614 1842/f 61.4 -- -- 16.3/f 16.3/f 0.163 -- -- (100)* (900/f 2 )* 1.0 f/300 5 Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) 0.3-1.34 1.34-30.0 30-300 300-1500 15,00-100,000 614 824/f 27.5 -- -- 1.63 2.19/f 0.073 -- -- (100)* (180/f 2 )* 0.2 f/1500 1 Power density S [mW /cm2] for controlled area at 850 MHz ，(TX: 824MHz – 849MHz) 75.2 300 824 300 )(  MHzf S mW/cm 2 Power density S [mW /cm2] for uncontrolled area at 850 MHz 55.0 1500 824 1500 )(  MHzf S mW /cm 2 Power density S [mW /cm2] for uncontrolled area at 1900/2400 MHz S=1 mW/cm 2 Reference levels are provided for exposure assessment to determine whether the basic restrictions on exposure of humans to electromagnetic fields are exceeded. The basic restrictions on exposure to electromagnetic fields are based directly on established health effects and biological considerations. 3 Location of EUT The source of the radiation is mounted on terminal; generally the direction of the antenna position is uprightness tabletop. The highest level of emission would be expected in close vicinity of the antenna and in line of sight to the antenna. 4 Prediction of the Exposure to Electromagnetic Fields Calculations can be made on a site by site basis to ensure the power density is below the limits given above, or guidelines can be done beforehand to ensure the minimum distances MU509-g Electromagnetic Radiation Exposure Estimation 3 from the antenna is maintained through the site planning. The calculations are based on FCC OET 65 Appendix B. 4.1 Calculation of the Safe Distance Below method describes a theoretical approach to calculate possible exposure to electromagnetic radiation around a base station transceiver antenna. Precise statements are basically only possible either with measurements or complex calculations considering the complexity of the environment (e.g. soil conditions, near buildings and other obstacles) which causes reflections, scattering of electromagnetic fields. The maximum output power (given in EIRP) of a base station is usually limited by license conditions of the network operator. A rough estimation of the expected exposure in power flux density on a given point can be made with the following equation. The calculations are based on FCC OET 65 Appendix B.    )(4 )( 2 mr GWP S numeric Whereas: P = Maximum output power in W of the site G numeric = Numeric gain of the antenna relative to isotropic antenna R = distance between the antenna and the point of exposure in meters 4.2 Technical Description MU509-g Technical Specification: Cellular Band: Power at antenna connector BTS: 32.65dBm（GSM850）/22.86 dBm（WCDMA850） Antenna-cable attenuation: 0 dB Input power to antenna: 32.65dBm（1.84W）（GSM850）/ 22.86 dBm (0.19W) （WCDMA850） Antenna gain: 4.28 dBi (2.68) PCS Band: Power at antenna connector BTS: 29.87dBm（GSM1900）/22.86dBm（WCDMA1900） Antenna-cable attenuation: 0 dB MU509-g Electromagnetic Radiation Exposure Estimation 4 Input power to antenna: 29.87dBm（0.97W）（GSM1900）/22.86dBm（0.19W） （WCDMA1900） Antenna gain: 3 dBi (2.0) 4.3 Estimation of compliance boundary for indoor antenna 1) Cellular Band : GSM850 For the final determination of the compliance boundary the model for far-field calculation is used since this overestimates the field strength in the near-field region. Thus the calculated compliance boundary should be rather more conservative and on the safe side. For EUT the following compliance boundary is calculated: Compliance boundary For GSM 850MHz band: When r=20cm and GSM only use one timeslot, so    )(4*8 )( 2 timeslotone mr GWP S numeric   2 timeslotone 204*8 68.2*1840 S =0.123 mW/cm 2 For GPRS and EDGE, the transmitter support multi-timesl…

Text truncated - open the document above for the full version.

FCC RF Test Report Product Name: HSDPA Module Model Number: MU509-g Report No: SYBH(Z-RF)025092011-2001 FCC ID: QISMU509G Reliability Laboratory of Huawei Technologies Co., Ltd. Huawei Base, Bantian, Longgang District, Shenzhen 518129, P.R. China Tel: +86 755 28780808 Fax: +86 755 89652518 FCC Test Report of MU509-g FCC ID: QISMU509G Security Level: Public Report No: SYBH(Z-RF)025092011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page2, Total38 Notice 1. The laboratory has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L0310. 2. The laboratory has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 97456. 3. The laboratory has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 6369A-2. 4. The test report is invalid if not marked with "exclusive stamp for the test report". 5. The test report is invalid if not marked with the stamps or the signatures of the persons responsible for performing, revising and approving the test report. 6. The test report is invalid if there is any evidence of erasure and/or falsification. 7. If there is any dissidence for the test report, please file objection to the test centre within 15 days from the date of receiving the test report. 8. Normally, the test report is only responsible for the samples that have undergone the test. 9. Context of the test report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of the laboratory. FCC Test Report of MU509-g FCC ID: QISMU509G Security Level: Public Report No: SYBH(Z-RF)025092011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page3, Total38 Notice 2 Modification Information: Table 1 Modification Information Modification Information 1 2 3 4 5 6 7 FCC Test Report of MU509-g FCC ID: QISMU509G Security Level: Public Report No: SYBH(Z-RF)025092011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page4, Total38 REGULATION FCC CFR47 Part 2: Subpart J; FCC CFR47 Part 22: Subpart H; START OF TEST Sep.27, 2011 END OF TEST Sep.28, 2011 Final Judgement: Pass Approved By Sep.30, 2011 Dai Linjun Date Name Signature Reviewed By Sep.30, 2011 Xuguangyi Date Name Signature Operator Sep.30, 2011 huangqiuliang Date Name Signature FCC Test Report of MU509-g FCC ID: QISMU509G Security Level: Public Report No: SYBH(Z-RF)025092011-2001 Confidential Information of Huawei. No Distribution without W ritten Permission Page5, Total38 Contents 1 Summary ............................................................................................................................................ 6 2 Product Description ........................................................................................................................... 7 2.1 PRODUCTION INFORMATION .............................................................................................................. 7 2.2 MODIFICATION INFORMATION ............................................................................................................. 7 3 Test Site Description .......................................................................................................................... 8 3.1 TESTING PERIOD .............................................................................................................................. 8 3.2 GENERAL SET UP DESCRIPTION ........................................................................................................ 8 4 Product Description ........................................................................................................................... 9 4.1 TECHNICAL CHARACTERISTICS .......................................................................................................... 9 4.2 EUT IDENTIFICATION LIST ............................................................................................................... 11 5 Main Test Instruments ..................................................................................................................... 12 6 Transmitter Measurements ............................................................................................................. 13 6.1 EFFECTIVE RADIATED POWER OF TRANSMITTER (ERP) ..................................................................... 13 6.2 CONDUCTED POWER OF TRANSMITTER ............................................................................................ 17 6.3 MODULATION CHARACTERISTICS ..................................................................................................... 20 6.4 OCCUPIED BANDWIDTH................................................................................................................... 22 6.5 BAND EDGES COMPLIANCE ............................................................................................................. 25 6.6 SPURIOUS EMISSION AT ANTENNA TERMINAL .................................................................................... 27 6.7 RADIATED SPURIOUS EMISSIONS ..................................................................................................... 30 6.8 FREQUENCY STABILITY ................................................................................................................... 33 7 System Measurement Uncertainty .................................................................................................. 37 8 Appendices ....................................................................................................................................... 38 FCC Test Report of MU509-g FCC ID: QISMU509G Security Level: Public Report No: SYBH(Z-RF)025092011-2001 Confidential Information of Huaw…

Text truncated - open the document above for the full version.