QISPRRU3901pico Remote Radio Unit

LampSite Installation Guide Issue02 Date2014-05-27 HUAWEI TECHNOLOGIES CO., LTD. Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address:Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website:http://www.huawei.com Email:[email protected] Issue 02 (2014-05-27)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. i About This Document Overview This document describes how to install the modules and cables for the RHUB3908 and pRRU3901 indoors. It also provides checklists for hardware installation. Product Version The following table lists the product version related to this document. Product NameProduct Version RHUB3908 (referred to as RHUB in this document) V100R009C00 and later versions Single-mode versions mapping V100R009C00: lNodeB: V200R016C00 leNodeB: V100R007C00 pRRU3901 (referred to as pRRU in this document) Intended Audience This document is intended for: lBTS installation personnel LampSite Installation GuideAbout This Document Issue 02 (2014-05-27)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. ii Contents About This Document.....................................................................................................................ii 1 Changes in LampSite Installation Guide.................................................................................1 2 Installation Preparations..............................................................................................................4 2.1 Reference Documents.....................................................................................................................................................5 2.2 Preparing Tools and Instruments....................................................................................................................................5 2.3 Requirements for Installation Personnel.........................................................................................................................6 3 Unpacking and Checking............................................................................................................7 4 Installing an RHUB.......................................................................................................................9 4.1 Information About the Installation...............................................................................................................................10 4.1.1 RHUB Installation Scenarios.....................................................................................................................................10 4.1.2 Installation Clearance Requirements of an RHUB....................................................................................................14 4.1.3 Installation Environment of an RHUB......................................................................................................................16 4.2 Installation Process.......................................................................................................................................................18 4.3 Installing an RHUB......................................................................................................................................................18 4.3.1 Installing an RHUB in a 19-Inch Cabinet or Rack....................................................................................................18 4.3.2 Installing an RHUB in a 19-Inch Shelf.....................................................................................................................21 4.3.3 Installing an RHUB on a Wall...................................................................................................................................24 4.4 Installing RHUB Cables...............................................................................................................................................28 4.4.1 Requirements for Cable Layout.................................................................................................................................28 4.4.2 RHUB Cable List.......................................................................................................................................................30 4.4.3 Cable Connections.....................................................................................................................................................32 4.4.4 RHUB Cable Installation Process..............................................................................................................................32 4.4.5 Installing an RHUB PGND Cable....................................................................................................................…

Text truncated - open the document above for the full version.

Doc. Code pRRU3901 Compliance and Safety Manual Issue 01 Date 2012-07-19 HUAWEI TECHNOLOGIES CO., LTD. Issue 01 (2012-02-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. i Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website: http://www.huawei.com Email: [email protected] pRRU3901Compliance and Safety Manual Contents Issue 01 (2012-02-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. ii Contents 1 Regulatory Compliance Information ..................................................................................... 1-1 1.1 About This Chapter ....................................................................................................................................... 1-1 1.2 Regulatory Compliance Standards ................................................................................................................ 1-1 1.3 Japanese Regulatory Compliance .................................................................................................................. 1-2 1.3.1 VCCI .................................................................................................................................................... 1-2 1.4 USA Regulatory Compliance ........................................................................................................................ 1-3 1.4.1 FCC Part 15.......................................................................................................................................... 1-3 1.5 Canada Regulatory Compliance .................................................................................................................... 1-3 1.5.1 RSS-Gen statement .............................................................................................................................. 1-3 1.5.2 RSS-102 statement: .............................................................................................................................. 1-4 2 Safety Information ..................................................................................................................... 2-5 2.1 About This Chapter ....................................................................................................................................... 2-5 2.2 Overview ....................................................................................................................................................... 2-5 2.2.1 Safety Precautions ................................................................................................................................ 2-5 2.2.2 General Requirements .......................................................................................................................... 2-6 2.3 Electricity Safety ........................................................................................................................................... 2-7 2.3.1 High Voltage ........................................................................................................................................ 2-7 2.3.2 Thunderstorm ....................................................................................................................................... 2-7 2.3.3 Tools ..................................................................................................................................................... 2-8 2.3.4 High Electrical Leakage ....................................................................................................................... 2-8 2.3.5 Power Cable ......................................................................................................................................... 2-8 2.3.6 Fuse ...................................................................................................................................................... 2-9 2.3.7 Battery .................................................................................................................................................. 2-9 2.4 Electrostatic Discharge ................................................................................................................................ 2-11 2.5 Inflammable Environment ........................................................................................................................... 2-12 2.5.1 Laser................................................................................................................................................... 2-12 2.6 Working at Heights .....................................................................................................................…

Text truncated - open the document above for the full version.

LampSite Site Maintenance Guide Issue02 Date2014-05-27 HUAWEI TECHNOLOGIES CO., LTD. Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address:Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website:http://www.huawei.com Email:[email protected] Issue 02 (2014-05-27)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. i About This Document Overview This document describes routine maintenance items for a RHUB3908 and pRRU3901, such as equipment maintenance, and power-on and power-off operations. It also explains how to replace the components and modules. Product Version The following table lists the product version related to this document. Product NameProduct Version RHUB3908 (referred to as RHUB in this document) V100R009C00 and later versions Single-mode versions mapping V100R009C00: lNodeB: V200R016C00 leNodeB: V100R007C00 pRRU3901 (referred to as pRRU in this document) Intended Audience This document is intended for: lSystem engineers lSite maintenance engineers Organization 1 Changes in LampSite Site Maintenance Guide This chapter provides information about the changes in different document versions of LampSite Site Maintenance Guide. 2 RHUB Maintenance Items LampSite Site Maintenance Guide About This Document Issue 02 (2014-05-27)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. ii This chapter describes the RHUB maintenance items, involving the equipment room, equipment, power system, and grounding system. 3 pRRU Maintenance Items This chapter describes the pRRU maintenance items, involving equipment and power system. 4 Powering On and Powering Off the RHUB After the RHUB is powered on, check the indicator status. Power off the RHUB in normal or emergency mode as required. 5 Powering On and Powering Off the pRRU After the pRRU is powered on, check the power supply voltage and indicator status. Power off the pRRU based on the power supply mode. 6 Replacing the RHUB The RHUB is an indoor convergence unit. It converges multiple pRRUs to the BBU. Replacing the RHUB interrupts services carried on the serving cell. 7 Replacing an Optical Module An optical module provides a port for opto-electronic conversion. This enables the transmission between the RHUB and BBU through the optical fiber. Replacing the optical module requires removing the optical fibers. This interrupts all the services. 8 Replacing the RF Daughter Board This section describes the procedures for replacing the RF daughter board of the pRRU. A pRRU can have two transmission ports or three transmission ports, requiring the same installation operations. This section uses the pRRU with three transmission ports as an example. Replacing an RF daughter board interrupts all the services carried on the pRRU. 9 Replacing the Wi-Fi Daughter Board This section describes the procedures for replacing the Wi-Fi daughter board, which applies only to a pRRU with three transmission ports.Replacing an Wi-Fi daughter board interrupts all the services carried on the pRRU. 10 Replacing the pDock Mother Board This section describes the procedure for replacing the pDock mother board. Replacing the pDock mother board of a pRRU will interrupt all services carried on the pRRU. A pDock mother board can have two transmission ports or three transmission ports, requiring the same installation operations. This section uses the pDock mother board with three transmission ports as an example. Conventions Symbol Conventions The symbols that may be found in this document are defined as follows. LampSite Site Maintenance Guide About This Document Issue 02 (2014-05-27)Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. iii SymbolDescription Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. NOTICE is used to address practices not related to personal injury. Calls attention to important information, best practices and tips. NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration. General Conventions The general conventions that may be found in this document are defined as follows. ConventionDescription Times New RomanNormal paragraphs are in Times New Roman. BoldfaceNames of files, directories, folders, and users are in boldface. For example, log in as user root. ItalicBook titles are in itali…

Text truncated - open the document above for the full version.

Huawei Technologies Co.,Ltd. Federal Communications Commission 2014-6-16 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: QISPRRU3901 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely.  Schematic diagram  Block Diagram  Parts list (BOM) Information  Operational description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the Commission withholds the following documents from public viewing for 180 days after the date the grant of equipment authorization is issued:  External Photos  Internal Photos  Test Setup Photos  Users Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. E-mail: [email protected] Fax: 0086-0755-28970299

EXTERNAL Photograhps （Total 10 Pages including this Cover Page） Supplement filename Description Photo-01 External Rear View – Front Photo-02 External Rear View – Back Photo-03 External Rear View – Left Photo-04 External Rear View – Right Photo-05 External Rear View –pRRU Ports and Indicators (with three transmission ports) Photo-06 External Rear View –pRRU Ports and Indicators (with two transmission ports) Photo-07 External Rear View – with Dock and connection Photo-08 Internal Rear View of UMTS Band II , LTE band 2 Photo-09 Internal Rear View of UMTS Band IV , LTE band 4 Photo-10 Internal Rear View of UMTS Band II+LTE band 4, UMTS Band IV+LTE band 2 Photo-11 Internal Rear View of UMTS Band II+LTE band 2 Photo-12 Internal Rear View of UMTS Band IV+LTE band 4 Photo-01 External Rear View - Front Photo-02 External Rear View - Back Photo-03 External Rear View -Left Photo-04 External Rear View -Right Photo-05 External Rear View -Ports and Indicators (with three transmission ports) Photo-06 External Rear View -Ports and Indicators (with two transmission ports) Photo-07 External Rear View -With AC/DC adapter and connection Photo-08 Internal Rear View of UMTS Band II , LTE band 2 Photo-09 Internal Rear View of UMTS Band IV, LTE band 4 Photo-10 Internal Rear View of UMTS Band II+LTE band 4, UMTS Band IV+LTE band 2 Photo-11 Internal Rear View of UMTS Band II+LTE band 2 Photo-12 Internal Rear View of UMTS Band IV+LTE band 4

INTERNAL Photograhps （Total 7 Pages including this Cover Page） Supplement filename Description Photo-01 Heads of WD6DIPX220 (UMTS Band II, LTE band 2) Photo-02 Rear of WD6DIPX220 (UMTS Band II, LTE band 2) Photo-03 Heads of WD6DLPX240 (UMTS Band IV, LTE band 4) Photo-04 Rear of WD6DLPX240 (UMTS Band IV, LTE band 4) Photo-05 Heads of WD6EXRUIBA (pDock mother board (with three transmission ports)) Photo-06 Rear of WD6EXRUIBA (pDock mother board (with three transmission ports)) Photo-07 Heads of WD6EMRI (pDock mother board (with two transmission ports)) Photo-08 Rear of WD6EMRI (pDock mother board (with two transmission ports)) Photo-01 Heads of WD6DIPX220 (UMTS Band II, LTE band 2) Photo-02 Rear of WD6DIPX220 (UMTS Band II, LTE band 2) Photo-03 Heads of WD6DLPX240 (UMTS Band IV, LTE band 4) Photo-04 Rear of WD6DLPX240 (UMTS Band IV, LTE band 4) Photo-09 Heads of WD6EXRUIBA (pDock mother board (with three transmission ports)) Photo-10 Rear of WD6EXRUIBA (pDock mother board (with three transmission ports)) Photo-11 Heads of WD6EMRI (pDock mother board (with two transmission ports)) Photo-12 Rear of WD6EMRI (pDock mother board (with two transmission ports))

Declaration for Compliance with EMF for pRRU3901 Security Level: Public Document No.: SYBH(R)01349980EB-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 1 of 4 Declaration of Electromagnetic Field Health Compliance To whom it may concern, As to the product pRRU3901 made by Huawei Technologies Co., Ltd., we declare that it complies with the Basic restrictions/Reference levels for electric, magnetic and electromagnetic fields as specified in following standards(s): Nr. Standard 1 47CFR FCC Part 1 (10-1-13 Edition) 2 RSS-102 (Issue4, March 2010) The compliance is demonstrated based on the following calculation model assessment: 1. The power density according to far-field model is: 2 ),( 4R GP S      Where: P = input power of the antenna. G = antenna gain relative to an isotropic antenna. , = elevation and azimuth angles. R = distance from the antenna to the point of investigation. 2. For single or multiple RF sources, the calculated power density should comply with following: 1 ,   i iLimit i S S Where: i S = the power density when the f is i . iLim it S , = the reference level requirement for power density when f is i . 3. The calculation of the power density or safe distance is: NOTE 1: The RF exposure evaluation is base on the far-field and the radiation exposure is over-estimated. NOTE 2: The maximum output power level is taken into account as a worst case for the purpose of the calculation of power density or safe distance. NOTE 3: The minimum antenna feed cable loss (assumed no cable loss) is taken into account as a worst case for the purpose of the calculation of power density or safe distance. NOTE 4: The maximum antenna radiation exposure orientation and maximum antenna gain is taken into account as a worst case for the purpose of the calculation of power density or safe distance. AWS Band: Declaration for Compliance with EMF for pRRU3901 Security Level: Public Document No.: SYBH(R)01349980EB-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 2 of 4 RF Source Calculation RF Source #1 f = 2110 to 2155 MHz iLim it S , = 10 2 W/m P = 0.316 W (=25 dBm) (rated power: 23dBm, tolerance: +/-2dB) ),( G = 2.51 (= 4 dBi) (Integrated antenna) ),( GPEIRP = 0.79316 W , = The worst condition is considered, i.e. the max G is used. R  0.25 m i S  2 ),( 4R GP     = 1.01 2 W/m iLim it i S S ,  0.101 RF Source Calculation RF Source #1 f = 2110 to 2155 MHz iLim it S , = 10 2 W/m P = 0.316 W (=25 dBm) (rated power: 23dBm, tolerance: +/-2dB) ),( G = 11.22 (= 10.5 dBi) (External antenna) ),( GPEIRP = 3.54552 W , = The worst condition is considered, i.e. the max G is used. R  0.25 m i S  2 ),( 4R GP     = 4.51 2 W/m iLim it i S S ,  0.451 PCS Band: RF Source Calculation RF Source #1 f = 1930 to 1990 MHz iLim it S , = 10 2 W/m P = 0.316 W (=25 dBm) (rated power: 23dBm, tolerance: +/-2dB) ),( G = 2.51 (= 4 dBi) (Integrated antenna) Declaration for Compliance with EMF for pRRU3901 Security Level: Public Document No.: SYBH(R)01349980EB-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 3 of 4 RF Source Calculation ),( GPEIRP = 0.79316 W , = The worst condition is considered, i.e. the max G is used. R  0.25 m i S  2 ),( 4R GP     = 1.01 2 W/m iLim it i S S ,  0.101 RF Source Calculation RF Source #1 f = 1930 to 1990 MHz iLim it S , = 10 2 W/m P = 0.316 W (=25 dBm) (rated power: 23dBm, tolerance: +/-2dB) ),( G = 11.22 (= 10.5 dBi) (External antenna) ),( GPEIRP = 3.54552 W , = The worst condition is considered, i.e. the max G is used. R  0.25 m i S  2 ),( 4R GP     = 4.51 2 W/m iLim it i S S ,  0.451 The product has different kinds of combinations, and the calculated results of these combinations are as below: Integrated antenna: AWS Band  i iLimit i S S ,  0.101 (Less than 1, so complied) PCS Band  i iLimit i S S ,  0.101 (Less than 1, so complied) AWS Band & PCS Band  i iLimit i S S ,  0.202 (Less than 1, so complied) AWS Band & AWS Band  i iLimit i S S ,  0.202 (Less than 1, so complied) Declaration for Compliance with EMF for pRRU3901 Security Level: Public Document No.: SYBH(R)01349980EB-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 4 of 4 PCS Band & PCS Band  i iLimit i S S ,  0.202 (Less than 1, so complied) External antenna: AWS Band  i iLimit i S S ,  0.451 (Less than 1, so complied) PCS Band  i iLimit i S S ,  0.451 (Less than 1, so complied) AWS Band & PCS Band  i iLimit i S S ,  0.902 (Less than 1, so complied) AWS Band & AWS Band  i iLimit i S S ,  0.902 (Less than 1, so complied) PCS Band & PCS Band  i iLimit i S S ,  0.902 (Less than 1, so complied) Calculated safe distance: 0.25 m Person responsible for making this declaration: ____________________________ Hu Wei RF Engineer, EMC Lab Reliability Laboratory of Huawei Technologies Co., Ltd. June 25, 2014

RF Test Report Product Name: pico Remote Radio Unit Product Model: pRRU3901 Report Number: SYBH(R)01349980EB-1 FCC ID: QISPRRU3901 IC: 6369A-PRRU3901 Reliability Laboratory of Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Tel: +86 755 28780808 Fax: +86 755 89652518 RF Test Report of pRRU3901 FCC ID: QISPRRU3901, IC: 6369A-PRRU3901 Security Level: Public Report No: SYBH(R)01349980EB-1 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 2 of 37 Notice 1. The laboratory has Passed the accreditation by China National Accreditation Service for Conformity Assessment (CNAS). The accreditation number is L0310. 2. The laboratory has Passed the accreditation by The American Association for Laboratory Accreditation (A2LA). The accreditation number is 2174.01. 3. The laboratory has been listed by the US Federal Communications Commission to perform electromagnetic emission measurements. The site recognition number for the test site located in Shenzhen is 97456, and the recognition numbers for the test site located in Shanghai is 684868. 4. The laboratory has been listed by Industry Canada to perform electromagnetic emission measurements. The recognition numbers are 6369A-1 for the 3m chamber test site located at G2 building, 6369A-2 for the 3m chamber test site located at K3 building and 6369A-3 for the 10m chamber test site located at K3 building in Shenzhen; the recognition numbers are 6369D-1 for the 3m chamber test site and 6369D-2 for the 10m chamber test site located in Shanghai. 5. The laboratory has been listed by the VCCI to perform EMC measurements. The accreditation numbers for the test site No.1 located at G2 building in Shenzhen are R-3892, G-415, C-4361, and T-1348, and the accreditation numbers for the test site No.2 located at K3 building in Shenzhen are R-3760, G-485, C-4210 and T-1237. 6. The test report is invalid if not marked with the signatures of the persons responsible for preparing and approving the test report. 7. The test report is invalid if there is any evidence of erasure and/or falsification. 8. The test report is only valid for the test samples. 9. Content of the test report, in part or in full, cannot be used for publicity and/or promotional purposes without prior written approval from the laboratory. RF Test Report of pRRU3901 FCC ID: QISPRRU3901, IC: 6369A-PRRU3901 Security Level: Public Report No: SYBH(R)01349980EB-1 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page …

Text truncated - open the document above for the full version.