QISS10-101WHUAWEI MediaPad 10 FHD

1 HUAWEI MediaPad 10 FHD Quick Start 1 Welcome Thank you to use the HUAWEI product——HUAWEI MediaPad 10 FHD (“HUAWEI MediaPad” for short as below.) For more information, please visit http://www.huaweidevice.com. The figures in this guide are provided for your reference only. The appearance and display features may vary slightly depending on the actual product version. 2 HUAWEI MediaPad at a Glance 1 Left Keyboard port 8 Headphone jack 2 Micro USB port 9 Speaker 3 Right Keyboard port 10 Fill light 4 Light sensor 11 Main camera 5 Front camera 12 Microphone 6 7 Volume key Power button 13 14 SIM card port MicroSD card port 2 3 Installing the SIM and microSD Cards 1. Remove the back cover. 2. Install the SIM card. When installing the SIM card, insert the card gently until it clicks firmly into place. 3. Install the microSD card. 4. Replace the back cover. 4 Switching Your HUAWEI MediaPad On Press and hold the Power button until your HUAWEI MediaPad vibrates to switch on it. The first time you switch on the HUAWEI MediaPad, complete the setup by following the on-screen instructions. To switch off your HUAWEI MediaPad, press and hold the Power button until the screen displays a dialog box, and then touch OK in the dialog box. When the HUAWEI MediaPad is switched on or malfunctions, press and hold the Power button for 10 seconds. After release, your HUAWEI MediaPad vibrates, indicating that it is restarting. 5 Locking the Screen When your HUAWEI MediaPad is turned on, press the Power button to lock the screen. If your HUAWEI MediaPad is idle for a preset period of time, the screen will lock automatically. 3 6 Unlocking the Screen 1. Press the Power button to wake up the screen. 2. Drag the unlock icon to any point of the circle that is around the icon. 7 Warnings and Precautions To use the device properly and safely, read these warnings and precautions carefully and strictly observe them during operation. Unless otherwise specified, the term "device" refers to the device and its accessories. Basic Requirements During storage, transportation, and operation of the device, keep it dry and prevent it from colliding with other objects. Do not dismantle the device. In case of any fault, contact an authorized service center for assistance or repair. Without authorization, no organization or individual can change the mechanical, safety, or performance design of the device. When using the device, observe all applicable laws and regulations and respect the legal rights of other people. Environmental Requirements for Using the Device Keep the device far from sources of heat and fire, such as a heater or a candle. Keep the device far from electronic appliances that generate strong magnetic or electric fields, such as a microwave oven or a refrigerator. Place the device on a stable surface. Place the device in a cool and well-ventilated indoor area. Do not expose the device to direct sunlight. Keep the ambient temperature between 0°C and 35°C while the device is being charged. Keep the ambient temperature between 0°C to 35°C for using the device powered by a battery. 4 Do not place any object (such as a candle or a water container) on the device. If any foreign object or liquid enters the device, stop using the device immediately, power it off, remove all the cables connected to it, and then contact an authorized service center. During thunderstorms, power off the device, and then remove all the cables connected to it to prevent it from getting damaged due to lightning strikes. Traffic Security Observe local laws and regulations while using the device. In addition, if using the device while driving a vehicle, comply with the following guidelines: Concentrate on driving. Your first responsibility is to drive safely. Do not talk on the device while driving. Use hands-free accessories. When you have to make or answer a call, park the vehicle at the road side before using your device. RF signals may affect electronic systems of motor vehicles. For more information, consult the vehicle manufacturer. In a motor vehicle, do not place the device over the air bag or in the air bag deployment area. Otherwise, the device may hurt you owing to the strong force when the air bag inflates. Do not use your device while flying in an aircraft. Power off your device before boarding an aircraft. Using wireless devices in an aircraft may cause danger to the operation of the aircraft and disrupt the wireless telephone network. It may also be considered illegal. Precautions for Using Wireless Devices The device complies with the RF specifications when the device is used in portable exposure conditions or at a distance of 1.5 cm from your body. Do not use the device where using wireless devices is prohibited or may cause interference or danger. The radio waves generated by the device may interfere with the operation of electronic medical devices. If you are using any electrical medical device, contact its manufacturer for the restrictions on the use of the device. Do not take the device into operating rooms, intensive care units (ICUs), or coronary care units (CCUs). 5 Areas with Inflammables and Explosives Do not use the device where inflammables or explosives are stored, for example, in a gas station, oil depot, or chemical plant. Otherwise, explosions or fires may occur. In addition, follow the instructions indicated in text or symbols. Do not store or transport the device in the same box as inflammable liquids, gases, or explosives. Accessory Requirements Use only the accessories supplied or authorized by the device manufacturer. Otherwise, the performance of the device may get affected, the warranty for the device or the laws and regulations related to telecommunications terminals may become null and void, or an injury may occur. Do not use the power adapter if its cable is damaged. Otherwise, electric shocks or fires may occur. Ensure that the power adapter meets the specifications indicated on the device nameplate. Ensure tha…

Text truncated - open the document above for the full version.

Huawei Technologies Co., Ltd. Address：Huawei Industrial Base,Bantian Longgang,Shenzhen 518129, P.R China Post ZIP：518129 Page ：1/1 To: CETECOM Fax : NULL From:Zhang Xinghai Fax:0086-755-89652518 Tel:0086-755-89651014 Email address: [email protected] Http: www.huawei.com Subject：Letter of Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with the Code of Federal Regulations Title 47 Section 0.457 and 0.459 pertaining to confidential material. Huawei Technologies Co., Ltd. would like the following documents regarding this submission for FCC ID: QISS10-101W to be kept confidential: 1. Schematic diagram. 2. Block Diagram. 3. Parts list (BOM) Information. 4. Operational description. 5. Tune-up procedure The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, For and Behalf of: Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager

HUAWEI MediaPad 10 FHD SECRET Page1, Total4 Photo documentation of external of product HUAWEI MediaPad 10 FHD SECRET Page2, Total4 HUAWEI MediaPad 10 FHD SECRET Page3, Total4 HUAWEI MediaPad 10 FHD SECRET Page4, Total4

HUAWEI MediaPad 10 FHD SECRET Page1, Total 1

HUAWEI MediaPad 10 FHD SECRET Page1, Total 1 Label Location

HUAWEI MediaPad 10 FHD SECRET Page1, Total10 Photo documentation of interior of product HUAWEI MediaPad 10 FHD SECRET Page2, Total10 HUAWEI MediaPad 10 FHD SECRET Page3, Total10 HUAWEI MediaPad 10 FHD SECRET Page4, Total10 HUAWEI MediaPad 10 FHD SECRET Page5, Total10 HUAWEI MediaPad 10 FHD SECRET Page6, Total10 HUAWEI MediaPad 10 FHD SECRET Page7, Total10 HUAWEI MediaPad 10 FHD SECRET Page8, Total10 HUAWEI MediaPad 10 FHD SECRET Page9, Total10 HUAWEI MediaPad 10 FHD SECRET Page10, Total10

123456 1 A D B C A D B C 23456 REVIEWED DESIGNED HUAWEI TECH CO.,LTD. VERPART_NUMBER The type and specification of the components refer to the BOM DATEECA NO SHEETOF BB SCHEMETIC 18. Main Camera and Slave Camera 19. USB/Charge management 16. LCD interface 24. Test Points/JTAG/Shields 13. Battery/Vabrator 3. Hi3620V100 4. Hi3620V100 5. Hi3620V100 6. Hi3620V100 7. Hi3620V100 12. RESERVED 1. Contents 2. POWER TREE 9. Hi6421V200 10. Hi6421V200 11. 8/16GB eMMC AND LPDDR 17. TP 14. MIC & MR Sensor 21. SIM/TF card 23. MainBoard to SubBoard Connector 22. Ambient Light 20. Sensor/Status indicator 15. 3.5 Headphone port/Vibrator 8. GPU Power 25.2.85V DCDC 26. BCM4330 BB 27. WIFI RF 28.GPS RF A03021NWY SH2101UM YANGYONGXIANG 00171286 1 NA 03021NWY_SCH1ZH 28 2011-11-30 YANGWENTAO 00181297 123456 1 A D B C A D B C 23456 REVIEWED DESIGNED HUAWEI TECH CO.,LTD. VERPART_NUMBER The type and specification of the components refer to the BOM DATEECA NO SHEETOF Hi6421 VBUCK1 VBUCK4 Hi3620 GPU LDO2/LDO3 INPUT VBUCK5 VBUCK3 VBUCK2 Hi3620 VDD_USB_PICO/NANO;VDD_PERI;AVCC_HDMI;PCIE_VP POPDDR POWER;Hi3260_VREF;DDR_PHY IO;DDR_VREF_RET VOUT1_1V8 Hi3620 CPU 4core Hi3620 26M TCXO POWER VOUT2_1V1 Hi3620 SYS POWER;AVDDL_PLL VOUT3_1V2 Hi3620 HSIC_PHY POWER;DDR_PHY IO;DDR_VREF VOUT4_2V5 Hi3620 DSIO_D_PHY PWR;USB_PHY PWR;T-SENSOR PWR;PCIE PWR VPUT5_1V8 VOUT6_2V6 VOUT7_2V6 VOUT8_3V3 Hi3620 USB_PHY_PICO/NANO PWR EMMC VCCM POWER;EMMC 1.8V IO enable VOUT9_2V6 Hi3620 VDDQ_EFUSE/VDDQ_EFUSE_HDMI PWR VOUT10_1V8 NO USED (FINGER) VOUT11_2V85 VOUT12_2V85 NO USED(CAM APWR) VOUT13_2V6 NO USED VOUT14_1V8 BCM4330 WIFI&BT IO PWR VOUT15_3V3 CAP SENSOR PWR;assistant board power LCD IO PWR VOUT17_2V85 NO USED VOUT18_1V8 Hi3620 IO POWER;LIGHT SENSOR PWR;TP POWER VOUT16_1V8 VOUT19_2V85 all CAM Analog power;CAM LOWPWR DCDC Enable VOUT20_2V85 8M 5M VCM PWR;VCM LOWPWR enable HDMI_5V Charge pump /NO USED AP VOUT0_2V85 Hi3620 SDcard interface IO PWR switch 1.8V/2.6V CHG PMU Fuel gauge LCD PWR;LED DRIVER BC1.1 PWR FLASH LED DRIVER BCM4330 4.2V PWR BCM4751 PWR HEADSET PA MAX8903 VPH_PWR 2.Power Tree VBATT 1.2V BUCK CAM CORE GSM PA 5V BOOST TP/SK Hi3620 IO PWR;BC1.1 IO ;POPDDR;EMMC;TP IO/INT;SENSOR IO;BCM4751 2.85V BUCK CAM/SD A03021NWY SH2101UM SUNQIAODAN KF39018 YANXUXING 00166792 2 NA 03021NWY_SCH1ZH 28 2011-11-30 FETN-GSD G D S 123456 1 A D B C A D B C 23456 REVIEWED DESIGNED HUAWEI TECH CO.,LTD. VERPART_NUMBER The type and specification of the components refer to the BOM DATEECA NO SHEETOF FETN-GSD G D S CSI0_CLK_N CSI0_CLK_P CSI0_DATA0_N CSI0_DATA0_P CSI0_DATA1_N CSI0_DATA1_P CSI0_DATA2_N CSI0_DATA2_P CSI0_DATA3_N CSI0_DATA3_P CSI0_REXT DSI0_CLK_N DSI0_CLK_P DSI0_DATA0_N DSI0_DATA0_P DSI0_DATA1_N DSI0_DATA1_P DSI0_DATA2_N DSI0_DATA2_P DSI0_DATA3_N DSI0_DATA3_P DSI0_REXT DSI1_CSI1_CLK_N DSI1_CSI1_CLK_P DSI1_CSI1_DATA0_N DSI1_CSI1_DATA0_P DSI1_CSI1_DATA1_N DSI1_CSI1_DATA1_P DSI1_CSI1_DATA2_N DSI1_CSI1_DATA2_P DSI1_CSI1_DATA3_N DSI1_CSI1_DATA3_P DSI1_CSI1_REXT HDMI_CEC HDMI_CLK_N HDMI_CLK_P HDMI_DATA0_N HDMI_DATA0_P HDMI_DATA1_N HDMI_DATA1_P HDMI_DATA2_N HDMI_DATA2_P HDMI_EXT_SWING HDMI_HPD HDMI_SCL HDMI_SDA PCIE_RESREF PCIE_RX_N PCIE_RX_P PCIE_TX_N PCIE_TX_P PCIE_CLK_N PCIE_CLK_P USB_HSIC_DATA USB_HSIC_STROB USB0_DM USB0_DP USB0_REXT USB0_VBUS USB1_DM USB1_DP USB1_REXT USB1_VBUS USB1_ID SD_CLK SD_CMD SD_DATA0 SD_DATA1 SD_DATA2 SD_DATA3/GPIO_093 HSSIG Interface 1 of 6 G S D MHL 1% Hi3620v100 high speed siganl 3. Hi3620 1% 1% 1% LCD TO DOCKING 1M CAMERA 8M CAMERA 1.2V Level 1 23 Q301 0 1.69KR300 A9 A10 E7 E8 D8 D9 B9 B10 A11 A12 E9 N1 M1 M5 N5 N4 M4 R5 P5 P4 R4 P2 K1 J1 L4 K4 L5 K5 J4 H4 H5 J5 L2 E11 D4 D5 B4 B5 B6 B7 A7 A6 D6 D11 E12 D12 AF7 AJ5 AJ6 AF9 AF8 AJ3 AJ2 AE12 AF11 AJ12 AJ11 AF12 AE13 AC14 AC15 AF15 AH13 AF13 AG2 AF5 AE5 AF4 AF6 AE6 U300 HI3620V110 R3060 GPIO145_USB_APEN 47K R311 GPIO21_USBID_CTL HDMI_HPD HDMI_SDA HDMI_SCL HDMI_DATA2_P HDMI_DATA2_N HDMI_DATA1_P HDMI_DATA1_N HDMI_DATA0_P HDMI_DATA0_N HDMI_CLK_P HDMI_CLK_N CSI1_CLK_N 2 3 1 Q300 R301200 TP300 USB_PICOPHY_ID TP301 R310200 R3046.04K 6.04KR303 R3026.04K R30515 100NFC300 **0R309 USB_AP5V R307 0 R308 47K USB_PICOPHY_ID USB_PICOPHY_REXT CSI1_REXT CSI1_CLK_P CSI1_DATA0_N CSI1_DATA0_P SD_CLK USB_PICOPHY_DP USB_PICOPHY_DN CSI0_DATA0_N CSI0_CLK_N A03021NWY YANGWENTAO 00181297 3 NA 03021NWY_SCH1ZH 28 2011-11-30 YANGYONGXIANG 00171286 SH2101UM HDMI_EXT_SWING USB_HSIC_STROB CSI0_CLK_P CSI0_DATA0_P CSI0_DATA1_N CSI0_DATA1_P CSI0_DATA2_N CSI0_DATA2_P CSI0_DATA3_N CSI0_DATA3_P DSI0_CLK_N DSI0_CLK_P SD_CMD SD_DATA0 SD_DATA1 SD_DATA2 SD_DATA3 USB_HSIC_DATA CSI0_REXT DSI0_DATA3_N DSI0_DATA2_N DSI0_DATA2_P DSI0_DATA3_P DSI0_DATA1_P DSI0_DATA1_N DSI0_DATA0_P DSI0_DATA0_N DSI0_REXT USB_AP5V 2 3 1 Q302 R312 47K USB_AP5V USB_OUT5V 123456 1 A D B C A D B C 23456 REVIEWED DESIGNED HUAWEI TECH CO.,LTD. VERPART_NUMBER The type and specification of the components refer to the BOM DATEECA NO SHEETOF EMMC_CLK/GPIO_037 EMMC_CMD/GPIO_036 NAND_ALE/GPIO_008 NAND_BUSY0_N/GPIO_016 NAND_BUSY1_N/GPIO_017 NAND_BUSY2_N/GPIO_018 NAND_BUSY3_N/GPIO_019 NAND_CLE/GPIO_009 NAND_CS0_N/GPIO_012 NAND_CS1_N/GPIO_013 NAND_CS2_N/GPIO_014 NAND_CS3_N/GPIO_015 NAND_DATA00/GPIO_020 NAND_DATA01/GPIO_021 NAND_DATA02/GPIO_022 NAND_DATA03/GPIO_023 NAND_DATA04/GPIO_024 NAND_DATA05/GPIO_025 NAND_DATA06/GPIO_026 NAND_DATA07/GPIO_027 EMMC_DATA0/NAND_DATA08 EMMC_DATA1/NAND_DATA09 EMMC_DATA2/NAND_DATA10 EMMC_DATA3/NAND_DATA11 EMMC_DATA4/NAND_DATA12 EMMC_DATA5/NAND_DATA13 EMMC_DATA6/NAND_DATA14 EMMC_DATA7/NAND_DATA15 NAND_RE_N/GPIO_010 NAND_WE_N/GPIO_011 CAM_HSYNC/GPIO_052 CAM_PCLK/GPIO_053 CAM_VSYNC/GPIO_054 CAM_DATA7/GPIO_049 CAM_DATA8/GPIO_050 CAM_DATA9/GPIO_051 CAM_DATA5/GPIO_047 CAM_DATA6/GPIO_048 CAM_DATA1/GPIO_043 CAM_DATA2/GPIO_044 CAM_DATA3/GPIO_045 CAM_DATA4/GPIO_046 CAM_DATA0/GPIO_042 ISP_CCLK0/GPIO_067 ISP_CCLK2/GPIO_068 ISP_FSIN0/GPIO_061 ISP_FSIN1/GPIO_062 I2C2_SDA/GPIO_064 ISP_GPIO0/GPIO_069 ISP_GPIO1/GPIO_070 ISP_GPIO2/GPIO_071 ISP_GPIO3/GPIO_072 ISP_GPIO4/GPIO_073 ISP_GPIO5/GPIO_074 ISP_GPIO7/GPIO_076 ISP_GPIO8/GPIO_077 ISP_G…

Text truncated - open the document above for the full version.

FCC Test Report - EDR Product Name: HUAWEI MediaPad 10 FHD Model Number: S10-101w Report No: SYBH(Z-RF)001072012-2002 FCC ID: QISS10-101W Reliability Laboratory of Huawei Technologies Co., Ltd. Huawei Base, Bantian, Longgang District, Shenzhen 518129, P.R. China Tel: +86 755 28780808 Fax: +86 755 89652518 FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total32 Notice 1. The laboratory has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L0310. 2. The laboratory has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 97456. 3. The laboratory has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 6369A-2. 4. The test report is invalid if not marked with "exclusive stamp for the test report". 5. The test report is invalid if not marked with the stamps or the signatures of the persons responsible for performing, revising and approving the test report. 6. The test report is invalid if there is any evidence of erasure and/or falsification. 7. If there is any dissidence for the test report, please file objection to the test centre within 15 days from the date of receiving the test report. 8. Normally, the test report is only responsible for the samples that have undergone the test. 9. Context of the test report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of the laboratory. FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total32 REGULATION FCC CFR47 Part 2:2011: Subpart J; FCC CFR47 Part 15:2011: Subpart C; ANSI C63.10 START OF TEST Jun.27, 2012 END OF TEST Jul.06, 2012 Final Judgement: Pass Approved By Senior Engineer Jul.10, 2012 Dai Linjun Date Name Signature Reviewed By Jul.10, 2012 Cousy Xu Date Name Signature Operator Jul.10, 2012 Huang Qiuliang Date Name Signature FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page4, Total32 Contents 1 Summary .....................................................................................................................................................5 2 Product Description ...................................................................................................................................6 2.1 PRODUCTION INFORMATION ....................................................................................................................6 2.2 MODIFICATION INFORMATION ..................................................................................................................6 3 Test Site Description ..................................................................................................................................7 4 General Setup Description ........................................................................................................................7 5 Product Description ...................................................................................................................................8 5.1 TECHNICAL CHARACTERISTICS ................................................................................................................8 5.2 EUT IDENTIFICATION LIST .....................................................................................................................10 6 Main Test Instruments .............................................................................................................................12 7 Transmitter Measurements .....................................................................................................................13 7.1 BANDWIDTH MEASUREMENT ..................................................................................................................13 7.2 CARRIER FREQUENCY SEPARATION MEASUREMENT ................................................................................15 7.3 NUMBER OF HOPPING CHANNEL .............................................................................................................17 7.4 TIME OF OCCUPANCY ............................................................................................................................19 7.5 PEAK OUTPUT POWER ..........................................................................................................................21 7.6 BAND EDGE SPURIOUS EMISSION ...........................................................................................................23 7.7 CONDUCTED RF SPURIOUS ..................................................................................................................25 7.8 RADIATED SPURIOUS EMISSION & SPURIOUS IN RESTRICTED BAND ..........................................................27 7.9 CONDUCTED EMISSION AT POWER PORT ...............................................................................................29 8 System Measurement Uncertainty ..........................................................................................................31 9 Appendices List ........................................................................................................................................32 FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page5, Total32 1 Summary The table below summarizes the measurements and results for th…

Text truncated - open the document above for the full version.

FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page1, Total7 Appendix A Bandwidth measurement According to FCC Part 15.247 (a) (1) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total7 Modulation:π/4-DQPSK Channel 0 (2402MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total7 Channel 40 (2442MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page4, Total7 Channel 78 (2480MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page5, Total7 Modulation:8DPSK Channel 0 (2402MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page6, Total7 Channel 40 (2442MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page7, Total7 Channel 78 (2480MHz) ----------------------------------------The END------------------------------------------ FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page1, Total3 Appendix B Carrier frequency separation measurement According to FCC Part 15.247 (a) (1) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total3 Modulation:π/4-DQPSK Centred at Channel 40 FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total3 Modulation:8DPSK Centred at Channel 40 ----------------------------------------The END------------------------------------------ FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page1, Total3 Appendix C Number of hopping channel According to FCC Part 15.247 (a) (1) iii FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total3 Modulation:π/4-DQPSK Total hopping channels = 79 FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total3 Modulation:8DPSK Total hopping channels = 79 ----------------------------------------The END------------------------------------------ FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page1, Total5 Appendix D Time of occupancy According to FCC Part 15.247 (a) (1) iii FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total5 Modulation:π/4-DQPSK A burst (One time slot) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total5 A period (Less than 106.7 burst) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page4, Total5 Modulation:8DPSK A burst (One time slot) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page5, Total5 A period (Less than 106.7 burst) ----------------------------------------The END------------------------------------------ FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page1, Total7 Appendix E Peak output power According to FCC Part 15.247 (b) (1) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total7 Modulation:π/4-DQPSK Channel 0 (2402MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total7 Channel 40 (2442MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page4, Total7 Channel 78 (2480MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2002 Confidential Information of Huawei. No Distribution without Written Permission Page5, Total7 Modulation:8DPSK Channel 0 (2402MHz) FCC Test Report of S10-101w FCC ID: QISS10-101W Security …

Text truncated - open the document above for the full version.

FCC Test Report Product Name: HUAWEI MediaPad 10 FHD Model Number: S10-101w Report No: SYBH(Z-RF)001072012-2001 FCC ID: QISS10-101W Reliability Laboratory of Huawei Technologies Co., Ltd. Huawei Base, Bantian, Longgang District, Shenzhen 518129, P.R. China Tel: +86 755 28780808 Fax: +86 755 89652518 FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2001 Confidential Information of Huawei. No Distribution without Written Permission Page2, Total34 Notice 1. The laboratory has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L0310. 2. The laboratory has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 97456. 3. The laboratory has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 6369A-2. 4. The test report is invalid if not marked with "exclusive stamp for the test report". 5. The test report is invalid if not marked with the stamps or the signatures of the persons responsible for performing, revising and approving the test report. 6. The test report is invalid if there is any evidence of erasure and/or falsification. 7. If there is any dissidence for the test report, please file objection to the test centre within 15 days from the date of receiving the test report. 8. Normally, the test report is only responsible for the samples that have undergone the test. 9. Context of the test report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of the laboratory. FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2001 Confidential Information of Huawei. No Distribution without Written Permission Page3, Total34 REGULATION FCC CFR47 Part 2:2011: Subpart J; FCC CFR47 Part 15:2011: Subpart C; ANSI C63.10 START OF TEST Jun.27, 2012 END OF TEST Jul.06, 2012 Final Judgement: Pass Approved By Senior Engineer Jul.10, 2012 Dai Linjun Date Name Signature Reviewed By Jul.10, 2012 Cousy Xu Date Name Signature Operator Jul.10, 2012 Huang Qiuliang Date Name Signature FCC Test Report of S10-101w FCC ID: QISS10-101W Security Level: Public Report No: SYBH(Z-RF)001072012-2001 Confidential Information of Huawei. No Distribution without Written Permission Page4, Total34 Contents 1 Summary .................................................................................................................................................... 5 2 Product Description .................................................................................................................................. 6 2.1 PRODUCTION INFORMATION ................................................................................................................... 6 2.2 MODIFICATION INFORMATION.................................................................................................................. 6 3 Test Site Description ................................................................................................................................. 7 4 General Setup Description ........................................................................................................................ 7 5 Product Description .................................................................................................................................. 8 5.1 TECHNICAL CHARACTERISTICS ............................................................................................................... 8 5.2 EUT IDENTIFICATION LIST .................................................................................................................... 10 6 Main Test Instruments ............................................................................................................................ 12 7 Transmitter Measurements ...............................................................…

Text truncated - open the document above for the full version.