QISS7-701WAHUAWEI MediaPad 7 Youth

Quick Start 1 Congratulations on your purchase of the HUAWEI MediaPad 7 Youth. S7-701w does not have a rear camera. Press and hold the power key to power on or off your device or restart it. Press the power key once to turn on or off the screen. HUAWEI MediaPad 7 Youth at a Glance 2 Charging the Battery Installing the microSD Card 3 This section contains important information about the operation of your device. It also contains information about how to use the device safely. Read this information carefully before using your device. Electronic device Do not use your device if using the device is prohibited. Do not use the device if doing so causes danger or interference with other electronic devices. Interference with medical equipment  Follow rules and regulations set forth by hospitals and health care facilities. Do not use your device where prohibited.  Some wireless devices may affect the performance of hearing aids or pacemakers. Consult your service provider for more information.  Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket. Protecting your hearing when using a headset  To prevent possible hearing damage, do not listen at high volume levels for long periods.  Using a headset at high volumes may damage your hearing. To reduce this risk, lower the headset volume to a safe and comfortable level.  Exposure to high volumes while driving may cause distraction and increase your risk of an accident. Safety information 4 Areas with flammables and explosives  Do not use the device where flammables or explosives are stored (in a gas station, oil depot, or chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. In addition, follow the instructions indicated in text or symbols.  Do not store or transport the device in containers with flammable liquids, gases, or explosives. Traffic security  Observe local laws and regulations while using the device. To reduce the risk of accidents, do not use your wireless device while driving.  Concentrate on driving. Your first responsibility is to drive safely.  RF signals may affect the electronic systems of motor vehicles. For more information, consult the vehicle manufacturer.  Do not place the device over the air bag or in the air bag deployment area in a motor vehicle. Doing so may hurt you because of the strong force when the air bag inflates.  Do not use your device while flying in an aircraft or immediately before boarding. Using wireless devices in an aircraft may disrupt wireless networks, present a hazard to aircraft operation, or be illegal. Operating environment  Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in these environments may result in circuit malfunctions.  Do not use your device during thunderstorms to protect your device against any danger caused by lightning.  Ideal operating temperatures are 0°C to 35°C. Ideal storage temperatures are –20°C to 60°C. Extreme heat or cold may damage your device or accessories.  Do not expose your device to direct sunlight (such as on a car dashboard) for prolonged periods. 5  To protect your device or accessories from fire or electrical shock hazards, avoid rain and moisture.  Keep the device away from sources of heat and fire, such as a heater, microwave oven, stove, water heater, radiator, or candle.  Do not place sharp metal objects, such as pins, near the earpiece or speaker. The earpiece may attract these objects and result in injury.  Stop using your device or applications for a while if the device is overheated. If skin is exposed to an overheated device for an extended period, low temperature burn symptoms, such as red spots and darker pigmentation, may occur.  Do not touch the device's antenna. Otherwise, communication quality may be reduced.  Do not allow children or pets to bite or suck the device or accessories. Doing so may result in damage or explosion.  Observe local laws and regulations, and respect the privacy and legal rights of others. Child's safety  Comply with all precautions with regard to child's safety. Letting children play with the device or its accessories may be dangerous. The device includes detachable parts that may present a choking hazard. Keep away from children.  The device and its accessories are not intended for use by children. Children should only use the device with adult supervision. Accessories  Using an unapproved or incompatible power adapter, charger or battery may cause fire, explosion or other hazards.  Choose only accessories approved for use with this model by the device manufacturer. The use of any other types of accessories may void the warranty, may violate local regulations and laws, and may be dangerous. Please contact your retailer for information about the availability of approved accessories in your area. 6 Charger safety  For pluggable devices, the socket-outlet shall be installed near the devices and shall be easily accessible.  Unplug the charger from electrical outlets and the device when not in use.  Do not drop or cause an impact to the charger.  If the power cable is damaged (for example, the cord is exposed or broken), or the plug loosens, stop using it at once. Continued use may lead to electric shocks, short circuits, or fire.  Do not touch the power cord with wet hands or pull the power cord to disconnect the charger.  Do not touch the device or the charger with wet hands. Doing so may lead to short circuits, malfunctions, or electric shocks.  If your charger has been exposed to water, other liquids, or excessive moisture, take it to an authorized service center for inspection.  Ensure that the charger meets the requirements of Clause 2.5 in IEC60950-1/EN60950-1 and has…

Text truncated - open the document above for the full version.

Justification Letter Date (30/07/2013) BABT TCB Balfour House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, We, Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen, 518129, China hereby to do the Justification on original FCC application: Huawei MediaPad 7 Youth, S7-701wa, FCC ID: QISS7-701WA as following: S7-701wa is a mediaPad, It supports WIFI and Bluetooth. S7-701w is a mediaPad, it supports WIFI and Bluetooth. The difference between S7-701w (Product Type: Huawei MediaPad 7 Youth; Model No.: S7-701w; FCC ID: QISS7-701W, Grant date: 2013-06-28) and S7-701wa: 1) S7-701wa added the rear camera. And all the PCB and circuit are the same. 2) With different model no. The followed table is show the different between the 2 Models. So in FCC application for S7-701wa (FCC ID: QISS7-701WA), Test data for Bluetooth in report “SYBH(Z-RF)014072013-2001 is from report “SYBH(Z- RF)023052013-2001” in FCC application for S7-701w(FCC ID: QISS7-701W,Grant date: 2013-06-28), and this data according to Part 15C remains valid and applicable and they are representative of the compliance of S7-701wa. Test data for WIFI in report “SYBH(Z-RF)014072013 is from report “SYBH(Z-RF)023052013-2002 ” in FCC application for S7-701w(FCC ID: QISS7-701W,Grant date: 2013-06-28), and this data according to Part 15C remains valid and applicable and they are representative of the compliance of S7-701wa. Test data for Part 15B Unintentional Radiator is refer to new test report “SYBH(Z-EMC)042052013-2”, and this data according to Part 15B are representative of the compliance of S7-701wa. SAR Test data for WIFI in submitted report “SYBH(Z-SAR)022072013-2” is refer to report “SYBH(Z- SAR013052013-2” in FCC application for S7-701w(FCC ID: QISS7-701W,Grant date: 2013-06-28). So all the data according to OET Bulletin No. 65, Supplement C-2001, IEEE 1528-2003 remains valid and applicable and they are representative of the compliance of S7-701wa. Sincerely, For and Behalf of: Huawei Technologies Co., Ltd. Zhangxinghai EMC Laboratory Manager

Date (06/01/2013) BABT TCB Balfour House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, We, Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen, 518129, China hereby authorize TUV-SUD China Shenzhen Branch 6/F, H Hall, Century Craftwork Culture Square, No. 4001 Fuqiang Road, Futian District, Shenzhen 518048 P. R. China Bu Cookies Phone: +86-755-88286998 e-mail: [email protected] to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that neither we nor any party to this application are subject to denial of U.S. Federal benefits, which include FCC benefits, pursuant to section 5301 of Anti-Drug Abuse Act of 1988, U.S.C. 862 because of conviction for possession or distribution of controlled substance. This authorization is application to following FCC ID application: FCC ID: QISS7-701WA This authorization is valid until further written notice from Huawei Technologies Co., Ltd. Sincerely, For and Behalf of: Huawei Technologies Co., Ltd. Zhangxinghai EMC Laboratory Manager

Huawei Technologies Co.,Ltd. Federal Communications Commission 2013-07-04 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: QISS7-701WA To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Operational Description Bom List Tune-Up Procedure PCB Diagram Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. ***************************************************************************** In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the Commission withholds the following documents from public viewing until 2013-12-30: External Photos Internal Photos Test Setup Photos User Manual ****************************************************************************** It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. E-mail: [email protected] Fax: 0086-0755- 28970299

HUAWEI MediaPad 7 Youth SECRET Page1, Total7 Photo documentation of external of product HUAWEI MediaPad 7 Youth SECRET Page2, Total7 HUAWEI MediaPad 7 Youth SECRET Page3, Total7 HUAWEI MediaPad 7 Youth SECRET Page4, Total7 HUAWEI MediaPad 7 Youth SECRET Page5, Total7 HUAWEI MediaPad 7 Youth SECRET Page6, Total7 HUAWEI MediaPad 7 Youth SECRET Page7, Total7

HUAWEI MediaPad 7 Youth SECRET Page1, Total 1 Label Location

HUAWEI MediaPad 7 Youth SECRET Page1, Total 1

HUAWEI MediaPad 7 Youth SECRET Page1, Total8 Photo documentation of interior of product HUAWEI MediaPad 7 Youth SECRET Page2, Total8 HUAWEI MediaPad 7 Youth SECRET Page3, Total8 HUAWEI MediaPad 7 Youth SECRET Page4, Total8 HUAWEI MediaPad 7 Youth SECRET Page5, Total8 HUAWEI MediaPad 7 Youth SECRET Page6, Total8 HUAWEI MediaPad 7 Youth SECRET Page7, Total8 HUAWEI MediaPad 7 Youth SECRET Page8, Total8

Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Tel: +86 755 28780808 Fax: +86 755 89652518 FCC SAR Compliance Test Report Project Name: _______________________ Model : _______________________ FCC ID : _______________________ Report No. : _______________________ APPROVED (Lab Manager) PREPARED (Test Engineer) BY DATE 2013-07-22 2013-07-22 The test results of this test report relate exclusively to the item(s) tested , The HUAWEI does not assume responsibility for any conclusions and generalisations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of HUAWEI. Reliability Laboratory of Huawei Technologies Co., Ltd. S7-701wa QISS7-701WA SYBH(Z-SAR)022072013-2 HUAWEI MediaPad 7 Youth Report No.:SYBH(Z-SAR)022072013-2 FCC ID: QISS7-701WA 2013-07-22 Page 2 of 27 Table of Contents 1 General Information ............................................................................................................................................................ 4 1.1 Statement of Compliance .......................................................................................................................................... 4 1.2 RF exposure limits...................................................................................................................................................... 4 1.3 EUT Description ......................................................................................................................................................... 5 1.3.1 General Description ........................................................................................................................................... 6 1.4 Test specification(s) .................................................................................................................................................. 7 1.5 Testing laboratory ....................................................................................................................................................... 7 1.6 Applicant and Manufacturer ...................................................................................................................................... 7 1.7 Application details ...................................................................................................................................................... 7 1.8 Ambient Condition ..................................................................................................................................................... 7 2 SAR Measurement System ............................................................................................................................................. 8 2.1 SAR Measurement Set-up ....................................................................................................................................... 8 2.2 Test environment ........................................................................................................................................................ 9 2.3 Data Acquisition Electronics description ................................................................................................................ 9 2.4 Probe description ..................................................................................................................................................... 10 2.5 Phantom description ................................................................................................................................................ 11 2.6 Device holder description ........................................................................................................................................ 11 2.7 Test Equipment List ................................................................................................................................................. 12 3 SAR Measurement Procedure ...................................................................................................................................... 13 3.1 Scanning procedure ................................................................................................................................................. 13 3.2 Spatial Peak SAR Evaluation ................................................................................................................................. 14 3.3 Data Storage and Evaluation .................................................................................................................................. 15 4 System Verification Procedure ........................................................................................................................................ 17 4.1 Tissue Verification .................................................................................................................................................... 17 4.2 System Check ........................................................................................................................................................... 18 4.3 System check Procedure ........................................................................................................................................ 19 5 Measurement Uncertainty Evaluation .......................................................................................................................... 20 5.1 Measurement uncertainty evaluation for SAR test .............................................................................................. 20 5.2 Measurement uncertainty evaluation for system validation ..........................................................................…

Text truncated - open the document above for the full version.

Date: 2013-6-17 Test Laboratory: HUAWEI SAR/HAC Lab SystemPerformanceCheck-D2450-ES-Body DUT: Dipole 2450 MHz D2450V2; Type: D2450V2; Serial: D2450V2 - SN:860 Communication System: CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 1.988 S/m; ε r = 51.983; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY Configuration: lProbe: ES3DV3 - SN3168; ConvF(4.38, 4.38, 4.38); Calibrated: 2012-10-2; lSensor-Surface: 4mm (Mechanical Surface Detection), z = 2.0, 32.0 lElectronics: DAE4 Sn1305; Calibrated: 2013-1-8 lPhantom: SAM1; Type: SAM; Serial: TP-1475 lDASY52 52.8.4(1052); SEMCAD X 14.6.8(7028) Configuration/d=10mm, Pin=250mW/Area Scan (7x9x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 16.3 W/kg Configuration/d=10mm, Pin=250mW/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 92.699 V/m; Power Drift = -0.18 dB Peak SAR (extrapolated) = 31.8 W/kg SAR(1 g) = 14.3 W/kg; SAR(10 g) = 6.39 W/kg Maximum value of SAR (measured) = 16.1 W/kg 0 dB = 16.3 W/kg = 12.11 dBW/kg

Date: 2013-6-17 Test Laboratory: HUAWEI SAR/HAC Lab S7-701w WiFi 802.11b 11CH Rear side 0mm DUT: S7-701w; Type: HUAWEI MediaPad 7 Youth; Serial: SAR1 Communication System: WiFi (802.11*); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.023 S/m; ε r = 52.011; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY Configuration: lProbe: ES3DV3 - SN3168; ConvF(4.38, 4.38, 4.38); Calibrated: 2012-10-2; lSensor-Surface: 4mm (Mechanical Surface Detection), z = 2.0, 32.0 lElectronics: DAE4 Sn1305; Calibrated: 2013-1-8 lPhantom: SAM1; Type: SAM; Serial: TP-1475 lDASY52 52.8.4(1052); SEMCAD X 14.6.8(7028) Configuration/Body/Area Scan (13x9x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.681 W/kg Configuration/Body/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 4.205 V/m; Power Drift = -0.06 dB Peak SAR (extrapolated) = 1.97 W/kg SAR(1 g) = 0.652 W/kg; SAR(10 g) = 0.257 W/kg Maximum value of SAR (measured) = 0.718 W/kg 0 dB = 0.718 W/kg = -1.44 dBW/kg Date: 2013-6-17 Test Laboratory: HUAWEI SAR/HAC Lab S7-701w WiFi 802.11b 11CH Left side 0mm DUT: S7-701w; Type: HUAWEI MediaPad 7 Youth; Serial: SAR1 Communication System: WiFi (802.11*); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.023 S/m; ε r = 52.011; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY Configuration: lProbe: ES3DV3 - SN3168; ConvF(4.38, 4.38, 4.38); Calibrated: 2012-10-2; lSensor-Surface: 4mm (Mechanical Surface Detection), z = 2.0, 32.0 lElectronics: DAE4 Sn1305; Calibrated: 2013-1-8 lPhantom: SAM1; Type: SAM; Serial: TP-1475 lDASY52 52.8.4(1052); SEMCAD X 14.6.8(7028) Configuration/Body/Area Scan (13x9x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.279 W/kg Configuration/Body/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 5.435 V/m; Power Drift = 0.19 dB Peak SAR (extrapolated) = 0.764 W/kg SAR(1 g) = 0.298 W/kg; SAR(10 g) = 0.125 W/kg Maximum value of SAR (measured) = 0.342 W/kg 0 dB = 0.279 W/kg = -5.55 dBW/kg Date: 2013-6-17 Test Laboratory: HUAWEI SAR/HAC Lab S7-701w WiFi 802.11b 11CH Top side 0mm DUT: S7-701w; Type: HUAWEI MediaPad 7 Youth; Serial: SAR1 Communication System: WiFi (802.11*); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.023 S/m; ε r = 52.011; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY Configuration: lProbe: ES3DV3 - SN3168; ConvF(4.38, 4.38, 4.38); Calibrated: 2012-10-2; lSensor-Surface: 4mm (Mechanical Surface Detection), z = 2.0, 32.0 lElectronics: DAE4 Sn1305; Calibrated: 2013-1-8 lPhantom: SAM1; Type: SAM; Serial: TP-1475 lDASY52 52.8.4(1052); SEMCAD X 14.6.8(7028) Configuration/Body/Area Scan (13x9x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.301 W/kg Configuration/Body/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 11.117 V/m; Power Drift = 0.16 dB Peak SAR (extrapolated) = 0.702 W/kg SAR(1 g) = 0.273 W/kg; SAR(10 g) = 0.113 W/kg Maximum value of SAR (measured) = 0.314 W/kg 0 dB = 0.301 W/kg = -5.22 dBW/kg

Justification of the extended calibration of Dipole D2450V2 SN: 860 Per KDB 450824, we have Measured the Impedance and Return Loss as below, and the return loss is <-20dB, with 20% of prior calibration; the real or imaginary parts of the impedance is with 5 ohm of prior calibration. Therefore the verification result should support extended calibration. Calibration Date 2011-03-08 Measured Date 2013-03-07 Dipole2450 Head TST Target Value Measured Value Difference Impedance transformed to feed point 54.0Ω+2.2jΩ 53.99Ω+2.33jΩ R=-0.01Ω, X=0.13Ω Return Loss -27.2dB -27.4dB -0.74% Dipole2450 Body TST Target Value Measured Value Difference Impedance transformed to feed point 49.0Ω+4.9jΩ 48.93Ω+4.96jΩ R=-0.07Ω, X=0.06Ω Return Loss - 26.0dB -26.04dB -0.15% Measured Date 2011-03-08 2013-03-07 ------- Impedance Test-Head Return Loss Test-Head Impedance Test-Body Return Loss Test-Body

FCC RF Test Report Product Name: HUAWEI MediaPad 7 Youth Product Model: S7-701wa Report Number: SYBH(Z-RF)014072013-2002 FCC ID: QISS7-701WA Reliability Laboratory of Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Tel: +86 755 28780808 Fax: +86 755 89652518 FCC Test Report of S7-701wa FCC ID: QISS7-701WA Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 2 of 18 Notice 1. The laboratory has Passed the accreditation by China National Accreditation Service for Conformity Assessment (CNAS). The accreditation number is L0310. 2. The laboratory has Passed the accreditation by The American Association for Laboratory Accreditation (A2LA). The accreditation number is 2174.01. 3. The laboratory has been listed by the US Federal Communications Commission to perform electromagnetic emission measurements. The site recognition number is 97456. 4. The laboratory has been listed by Industry Canada to perform electromagnetic emission measurements. The recognition numbers of test site are 6369A-1 and 6369A-3. 5. The laboratory has been listed by the VCCI to perform EMC measurements. The accreditation numbers of test site No.1 are R-2364, G-415, C-2583, and T-256, and the accreditation numbers of test site No.2 are R-3760, G-485, C-4210 and T-1237. 6. The test report is invalid if not marked with the signatures of the persons responsible for preparing and approving the test report. 7. The test report is invalid if there is any evidence of erasure and/or falsification. 8. The test report is only valid for the test samples. 9. Content of the test report, in part or in full, cannot be used for publicity and/or promotional purposes without prior written approval from the laboratory. FCC Test Report of S7-701wa FCC ID: QISS7-701WA Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 3 of 18 Applicant: Huawei Technologies Co., Ltd. Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Date of Receipt Sample: 2013-06-30 Start Date of Test: 2013-07-10 End Date of Test: 2013-07-15 Test Result: Pass Approved by Senior Engineer: 2013-07-19 Dai Linjun Date Name Signature Prepared by: 2013-07-19 Zhang Guocai Date Name Signature FCC Test Report of S7-701wa FCC ID: QISS7-701WA Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 4 of 18 Modification Record No. Last Report No. Modification Description 1 First Report FCC Test Report of S7-701wa FCC ID: QISS7-701WA Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 5 of 18 CONTENT 1 General Information ................................................................................................................................................ 6 1.1 Applied Standard........................................................................................................................................ 6 1.2 Test Location ............................................................................................................................................. 6 1.3 Test Environment Condition ....................................................................................................................... 6 2 Test Summary ........................................................................................................................................................ 7 3 Description of the Equipment under Test (EUT) ..................................................................................................... 8 3.1 General Description ................................................................................................................................... 8 3.2 EUT Identity ............................................................................................................................................... 8 3.3 Technical Description ................................................................................................................................. 9 4 General Test Conditions / Configurations ............................................................................................................. 10 4.1 Test Modes .............................................................................................................................................. 10 4.2 EUT Configurations .................................................................................................................................. 11 4.3 Test Environments ................................................................................................................................... 12 4.4 Test Setups .............................................................................................................................................. 13 4.5 Test Conditions ........................................................................................................................................ 16 5 Main Test Instruments .......................................................................................................................................... 18 FCC Test Report of S7-701wa FCC ID: QISS7-701WA Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 6 of 18 1 General Information 1.1 Applied Standard Applied Rules: 47 CFR FCC Part 2, Subpart J 2012 47 CFR FCC Part 15, Subpart C 2012 Test Method: FCC KDB 558074 D01 DTS Meas Guidance v03r01 FCC KDB 662911 D01 Multiple Transmitter Output v02 ANSI C63.10-2009, American National Standard for Testing Unlicensed Wireless Devices. 1.2 Test Location Test Location 1: Reliability L…

Text truncated - open the document above for the full version.

FCC Test Report of S7-701wa FCC ID: QISS7-701WA Security Level: Public Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 1 of 105 Appendix for Test report FCC Test Report of S7-701wa FCC ID: QISS7-701WA Security Level: Public Report No: SYBH(Z-RF)014072013-2002 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Page 2 of 105 Appendix A: DTS (6 dB) Bandwidth In this document, the "DTS6dBBW" refers to the measured "DTS (6 dB) Bandwidth" value. In this Appendix, the "fc(DTS6dBBW)" refers to the centre of the measured "DTS6dBBW". The introduction of the "fc(DTS6dBBW)" is due to that other measurements use it as the spectrum analyzer setting. For measurements on smart antenna systems (devices with multiple transmit chains), the test is performed at each chain, and used as respective results for e…

Text truncated - open the document above for the full version.