QISY360-U03WCDMA Mobile Phone

1 Dual-Card Dual-Standby Your mobile phone supports dual-card dual-standby mode, which can significantly reduce power consumption and increase your phone's standby time. Note that two restrictions exist:
When you make calls using one SIM card, the other SIM card is disabled. For example, when you make calls using SIM card 1, SIM card 2 cannot be used to answer calls or access the Internet. If someone calls SIM card 2, the caller will hear a voice message like "The subscriber you dialed is out of the service zone" or "The subscriber you dialed is not able to answer your call, please try again later." This is because your mobile phone cannot access the network with both SIM cards at the same time and has nothing to do with your service provider's network condition. It is recommended that you subscribe to services such as voicemail or missed-call reminders from your service provider to avoid the inconvenience caused by missed calls.
When you are using one SIM card's data services, you can receive calls and messages using the other SIM card, but data services will be interrupted. For example, when SIM card 1's data services are in use, you can use SIM card 2 for calling and messaging, but SIM card 1's data services will be interrupted as a result. When the call using SIM card 2 is terminated, or the message is received or sent, you can resume using SIM card 1's data services. 2 Getting to know your phone Thank you for choosing the HUAWEI smartphone. First, let's take a look at a few basics. Press and hold the power button to power on your phone. After your phone is powered up, you can use the power button to turn the screen off and on. 3 Preparing your phone To insert SIM cards, the battery and a microSD card please perform the few steps shown in the following figures. Your phone is shipped with the battery partially charged. It is recommended that you fully charge the battery before using it for the first time. 4 Dual-Card Management Your mobile phone supports access to both WCDMA and GSM networks. Follow the onscreen instructions or the quick start guide to install SIM cards. 1. On the home screen, touch . 2. Touch SIM management to activate the SIM cards. 5 Locking and unlocking the screen When you are not using your phone, press the power button to turn off the screen. After being idle for a specified period of time, your phone locks its screen automatically. Follow the onscreen instructions and slide on the screen to unlock. 6 7 Making a call On the home screen, touch to open the dialer. You can dial a phone number directly. You can also touch a phone number in places like messages, email and webpages to make a call. To answer an incoming call, drag to . 8 Sending messages On the home screen, touch to open Messaging. Adding a photo or audio clip to a text message turns it into a multimedia message. You can also save attachments from multimedia messages. 9 Taking a photo or video On the home screen, touch to open Camera. Flick left or right to switch between photo and video capture modes. 10 Listening to music On the home screen, touch to open Music. You can copy songs to your phone and immerse yourself with extraordinary audio experience anytime. You can also mark your songs to add them to the playlist. 11 Surfing the web On the home screen, touch to open Browser. You can start surfing the web right away using your phone's browser and stay on ball with up-to-date news and information. Your browser supports multi-page browsing. Touch to switch among pages. 12 For more help Want to obtain the user guide? Search for and download the User Guide from http://consumer.huawei.com/en/. Please visit http://consumer.huawei.com/en/support/hotline/ for r ecently updated hotline and email address in your country or region. Personal information and data security The use of some functions or third-party applications on your device could result in your personal information and data being lost or becoming accessible to others. Several measures are recommended to help you protect personal and confidential information.
Place your device in a safe area to prevent it from unauthorized use.
Set your device screen to lock and create a password or unlock pattern to open it.
Periodically back up personal information kept on your SIM/USIM card, memory card, or stored in your device memory. If you change to a different device, be sure to move or delete any personal information on your old device.
If you are worried about viruses when you receive messages or emails from a stranger, you can delete them without opening them.
If you use your device to browse the Internet, avoid websites that might pose a security risk to avoid theft of your personal information.
If you use services such as Wi-Fi tether or Bluetooth, set passwords for these services to prevent unauthorized access. When these services are not in use, turn them off.
Install or upgrade device security software and regularly scan for viruses. 13
Be sure to obtain third-party applications from a legitimate source. Downloaded third-party applications should be scanned for viruses.
Install security software or patches released by Huawei or third-party application providers.
Some applications require and transmit location information. As a result, a third-party may be able to share your location information.
Your device may provide detection and diagnostic information to third-party application providers. Third party vendors use this information to improve their products and services.
If you have concerns about the security of your personal information and data, please contact [email protected]. 14 Legal notice Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved. Trademarks and permissions , , and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Android™ is a trademark of Google Inc. The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such …

Text truncated - open the document above for the full version.

Huawei Technologies Co.,Ltd. Federal Communications Commission 2014-11-26 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: QISY360-U03 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Operational Description Bom List Tune-Up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. ***************************************************************************** In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the Commission withholds the following documents from public viewing until 2015-03-31: External Photos Internal Photos Test Setup Photos User Manual ****************************************************************************** It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C E-mail: [email protected] Tel: 0086-0755-28970299 Fax: 0086-0755-89650226

Huawei Technologies Co.,Ltd. Date: November 28, 2014 Statement We, Huawei Technologies Co.,Ltd, states that our device, FCC ID: QISY360-U03, has a battery, But the battery will not be placed in the battery compartment when delivery, it is visible to the users as they purchase the products and install the battery. For and Behalf of: Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C E-mail: [email protected] Te l : 0086-0755-28970299 Fax: 0086-0755-89650226

文档名称 文档密级 2014-8-12 华为保密信息,未经授权禁止扩散 第1页, 共1页 Declaration Manufacturer/Application:Huawei Technologies Co.,Ltd FCC ID: QISY360-U03 I declare that the shielded USB cable used in the test will be marketed with the EUT. Yours sincerely, Product Manager: Email: [email protected]

Report No.: RXA1412-0270SAR01R3 Page 1 of 215 TESTING No. L2264 SAR TEST REPORT Product Name WCDMA Mobile Phone Model Name HUAWEI Y360-U03 Brand Name HUAWEI FCC ID QISY360-U03 Applicant Huawei Technologies Co., Ltd. Manufacturer Huawei Technologies Co., Ltd. Date of issue January 27, 2015 TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 2 of 215 GENERAL SUMMARY Reference Standard(s) FCC 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices ANSI C95.1, 1992: Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.(IEEE Std C95.1-1991) IEEE Std 1528™-2003: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. KDB 865664 D01 SAR measurement 100 MHz to 6 GHz v01r03: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 447498 D01 Mobile Portable RF Exposure v05r02: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 648474 D04 Handset SAR v01r02: SAR Evaluation Considerations for Wireless Handsets. KDB 941225 D01 SAR test for 3G devices v03: SAR Measurement Procedures CDMA 20001x RTT, 1x Ev-Do, WCDMA, HSDPA/HSPA KDB 941225 D06 Hotspot Mode SAR v02: SAR Evaluation Procedures for Portable Devices with Wireless Router Capabilities KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards for the tested bands only. General Judgment: Pass Comment The test result only responds to the measured sample. Approved by Kai Xu Director Revised by Jiangpeng Lan SAR Manager Performed by Jie Li SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 3 of 215 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the Test Report ....................................................................................................... 5 1.2. Testing Laboratory ................................................................................................................ 5 1.3. Applicant Information ............................................................................................................ 6 1.4. Manufacturer Information ...................................................................................................... 6 1.5. Information of EUT ................................................................................................................ 7 1.6. EUT Antenna Locations ........................................................................................................ 9 1.7. The Maximum Reported SAR 1g .......................................................................................... 10 1.8. Test Date ............................................................................................................................ 10 2. SAR Measurements System Configuration ................................................................................ 11 2.1. SAR Measurement Set-up .................................................................................................. 11 2.2. DASY5 E-field Probe System ............................................................................................. 12 2.2.1. EX3DV4 Probe Specification ....................................................................................... 12 2.2.2. E-field Probe Calibration .............................................................................................. 13 2.3. Other Test Equipment ......................................................................................................... 13 2.3.1. Device Holder for Transmitters .................................................................................... 13 2.3.2. Phantom ...................................................................................................................... 14 2.4. Scanning Procedure ........................................................................................................... 14 2.5. Data Storage and Evaluation .............................................................................................. 16 2.5.1. Data Storage ................................................................................................................ 16 2.5.2. Data Evaluation by SEMCAD ...................................................................................... 16 3. Laboratory Environment ............................................................................................................. 18 4. Tissue-equivalent Liquid ............................................................................................................ 19 4.1. Tissue-equivalent Liquid Ingredients ................................................................................... 19 4.2. Tissue-equivalent Liquid Properties .................................................................................... 21 5. Sy stem Check ............................................................................................................................ 22 5.1. Description of System Check .............................................................................................. 22 5.2. System Check Results ........................................................................................................ 23 6. Operational Conditions during Test ............................................................................................ 24 6.1. General Description of Test Proce…

Text truncated - open the document above for the full version.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 143 of 215 UMTS Band V Back Side Low (Battery 1) Date: 12/31/2014 Communication System: WCDMA Band V; Frequency: 826.4 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 826.4 MHz; σ = 0.993 mho/m; ε r = 55.2; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3977; ConvF(9.74, 9.74, 9.74); Calibrated: 2/17/2014; Electronics: DAE4 Sn1291; Calibrated: 11/14/2014 Phantom: SAM 11; Type: SAM V4.0; Serial: TP-1246 Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Back Side Low/Area Scan (61x101x1): Measurement grid: dx=1.500mm, dy=1.500mm Maximum value of SAR (interpolated) = 1.15 mW/g Back Side Low/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 34.4 V/m; Power Drift = 0.017 dB Peak SAR (extrapolated) = 1.37 W/kg SAR(1 g) = 1.1 mW/g; SAR(10 g) = 0.821 mW/g Maximum value of SAR (measured) = 1.16 mW/g Figure 90 Body, Back Side, UMTS Band V Channel 4132 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 144 of 215 UMTS Band V Front Side High (Battery 1) Date: 12/31/2014 Communication System: WCDMA Band V; Frequency: 846.6 MHz;Duty Cycle: 1:1 Medium parameters used: f = 847 MHz; σ = 1.01 mho/m; ε r = 55; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3977; ConvF(9.74, 9.74, 9.74); Calibrated: 2/17/2014; Electronics: DAE4 Sn1291; Calibrated: 11/14/2014 Phantom: SAM 11; Type: SAM V4.0; Serial: TP-1246 Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Front Side High/Area Scan (61x101x1): Measurement grid: dx=1.500mm, dy=1.500mm Maximum value of SAR (interpolated) = 1.09 mW/g Front Side High/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 33.3 V/m; Power Drift = 0.018 dB Peak SAR (extrapolated) = 1.29 W/kg SAR(1 g) = 1.04 mW/g; SAR(10 g) = 0.782 mW/g Maximum value of SAR (measured) = 1.09 mW/g Figure 91 Body, Front Side, UMTS Band V Channel 4233 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 145 of 215 UMTS Band V Front Side Middle (Battery 1) Date: 12/31/2014 Communication System: WCDMA Band V; Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: f = 837 MHz; σ = 1 mho/m; ε r = 55.1; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3977; ConvF(9.74, 9.74, 9.74); Calibrated: 2/17/2014; Electronics: DAE4 Sn1291; Calibrated: 11/14/2014 Phantom: SAM 11; Type: SAM V4.0; Serial: TP-1246 Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Front Side Middle/Area Scan (61x101x1): Measurement grid: dx=1.500mm, dy=1.500mm Maximum value of SAR (interpolated) = 0.970 mW/g Front Side Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 31.4 V/m; Power Drift = -0.010 dB Peak SAR (extrapolated) = 1.15 W/kg SAR(1 g) = 0.924 mW/g; SAR(10 g) = 0.695 mW/g Maximum value of SAR (measured) = 0.971 mW/g Figure 92 Body, Front Side, UMTS Band V Channel 4183 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 146 of 215 UMTS Band V Front Side Low (Battery 1) Date: 12/31/2014 Communication System: WCDMA Band V; Frequency: 826.4 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 826.4 MHz; σ = 0.993 mho/m; ε r = 55.2; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3977; ConvF(9.74, 9.74, 9.74); Calibrated: 2/17/2014; Electronics: DAE4 Sn1291; Calibrated: 11/14/2014 Phantom: SAM 11; Type: SAM V4.0; Serial: TP-1246 Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Front Side Low/Area Scan (61x101x1): Measurement grid: dx=1.500mm, dy=1.500mm Maximum value of SAR (interpolated) = 0.946 mW/g Front Side Low/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 31.2 V/m; Power Drift = -0.013 dB Peak SAR (extrapolated) = 1.12 W/kg SAR(1 g) = 0.901 mW/g; SAR(10 g) = 0.679 mW/g Maximum value of SAR (measured) = 0.947 mW/g Figure 93 Body, Front Side, UMTS Band V Channel 4132 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 147 of 215 UMTS Band V Left Edge Middle (Battery 1) Date: 12/31/2014 Communication System: WCDMA Band V; Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: f = 837 MHz; σ = 1 mho/m; ε r = 55.1; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3977; ConvF(9.74, 9.74, 9.74); Calibrated: 2/17/2014; Electronics: DAE4 Sn1291; Calibrated: 11/14/2014 Phantom: SAM 11; Type: SAM V4.0; Serial: TP-1246 Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Left Edge Middle/Area Scan (51x151x1): Measurement grid: dx=1.000mm, dy=1.000mm Maximum value of SAR (interpolated) = 0.485 mW/g Left Edge Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 21.3 V/m; Power Drift = 0.011 dB Peak SAR (extrapolated) = 0.631 W/kg SAR(1 g) = 0.457 mW/g; SAR(10 g) = 0.318 mW/g Maximum value of SAR (measured) = 0.487 mW/g Figure 94 Body, Left Edge, UMTS Band V Channel 4183 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1412-0270SAR01R3 Page 148 of 215 UMTS Band V Right Edge Middle (Battery 1) Date: 12/31/2014 Communication System: WCDMA Band V; Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium…

Text truncated - open the document above for the full version.

GSM 850 Date: 12.DEC.2014 14:26:21 Date: 12.DEC.2014 14:38:31 GPRS 850 Date: 12.DEC.2014 14:47:29 Date: 12.DEC.2014 14:45:21 GSM 1900 Date: 11.DEC.2014 09:42:55 Date: 11.DEC.2014 09:50:45 GPRS 1900 Date: 11.DEC.2014 09:59:38 Date: 11.DEC.2014 09:53:51 WCDMA 850 Date: 3.DEC.2014 18:42:13 Date: 3.DEC.2014 18:43:44 HSDPA 850 Date: 3.DEC.2014 18:58:06 Date: 3.DEC.2014 18:56:53 HSUPA850 Date: 3.DEC.2014 18:53:34 Date: 3.DEC.2014 18:55:19 WCDMA 1900 Date: 3.DEC.2014 16:38:11 HSDPA 1900 Date: 3.DEC.2014 17:10:16 Date: 3.DEC.2014 17:11:28 HSUPA 1900 Date: 3.DEC.2014 17:22:03 Date: 3.DEC.2014 17:23:13

GSM 850 (99% bandwidth) Date: 3.DEC.2014 14:59:05 GSM1900 (99% bandwidth) Date: 3.DEC.2014 15:46:04 GPRS 850 (99% bandwidth) Date: 3.DEC.2014 15:27:11 GPRS 1900 (99% bandwidth) Date: 3.DEC.2014 16:18:50 GSM 850 (26dB bandwidth) Date: 3.DEC.2014 14:57:52 GSM 1900 (26dB bandwidth) Date: 3.DEC.2014 15:48:13 GPRS 850 (26dB bandwidth) Date: 3.DEC.2014 15:28:56 GPRS 1900 (26dB bandwidth) Date: 3.DEC.2014 16:19:59 WCDMA 850 (99% bandwidth) Date: 3.DEC.2014 18:33:52 WCDMA 1900 (99% bandwidth) Date: 3.DEC.2014 16:41:32 HSDPA 850 (99% bandwidth) Date: 3.DEC.2014 19:02:21 HSDPA 1900 (99% bandwidth) Date: 3.DEC.2014 17:05:39 HSUPA 850 (99% bandwidth) Date: 3.DEC.2014 18:47:13 HSUPA 1900 (99% bandwidth) Date: 3.DEC.2014 17:18:35 WCDMA 850 (26dB bandwidth) Date: 3.DEC.2014 18:35:11 WCDMA 1900 (26dB bandwidth) Date: 3.DEC.2014 16:35:01 HSDPA 850 (26dB bandwidth) Date: 3.DEC.2014 19:03:03 HSDPA 1900 (26dB bandwidth) Date: 3.DEC.2014 17:06:21 HSUPA 850 (26dB bandwidth) Date: 3.DEC.2014 18:48:51 HSUPA 1900 (26dB bandwidth) Date: 3.DEC.2014 17:19:14

GSM 850 Date: 3.DEC.2014 15:10:22 Date: 3.DEC.2014 15:12:05 GSM 1900 GPRS 850 Date: 3.DEC.2014 15:31:29 Date: 3.DEC.2014 15:32:30 GPRS 1900 WCDMA 850 Date: 3.DEC.2014 18:39:53 Date: 3.DEC.2014 18:40:40 WCDMA 1900 HSDPA 850 Date: 3.DEC.2014 19:00:04 Date: 3.DEC.2014 19:00:49 HSDPA 1900 HSUPA850 Date: 3.DEC.2014 18:51:11 Date: 3.DEC.2014 18:51:43 HSUPA 1900

 The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained.  This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.  For Terms And Conditions of the services, it can be provided upon request.  The evaluation data of the report will be kept for 3 years from the date of issuance. TRF No.: FCC 22H&24E_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com TEST REPORT Report Number: 141127003SZN-006 Application for Original Grant of 47 CFR Part 22 and Part 24 Certification WCDMA Mobile Phone FCC ID: QISY360-U03 Prepared and Checked by: Approved by: Sign on file William Chen Leung Wai Leung, Tommy Project Engineer Deputy General Manager January 20, 2015 INTERTEK TESTING SERVICES TRF: FCC 22H&24E_b Test Report Number: 141127003SZN-006 FCC ID: QISY360-U03 GENERAL INFORMATION Applicant Name: Huawei Technologies Co.,Ltd Applicant Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C FCC Specification Standard: FCC Part 22: 2013 FCC Part 24: 2013 FCC ID: QISY360-U03 FCC Model(s): HUAWEI Y360-U03 Type of EUT: WCDMA/HSDPA/HSUPA/HSPA+/GSM/GPRS /EDGE Digital Mobile Phone with Bluetooth and WiFi Note: EDGE & HSPA+ support Downlink only Description of EUT: WCDMA Mobile Phone Serial Number: E2K9XAT4B0700025 Sample Receipt Date: 27 November 2014 Date of Test: 27 November 2014 to 15 December 2014 Report Date: January 20, 2015 Environmental Conditions: Temperature: 25 ± 10°C Humidity: 10 to 90% INTERTEK TESTING SERVICES TRF: FCC 22H&24E_b Test Report Number: 141127003SZN-006 FCC ID: QISY360-U03 List of Exhibits Exhibit Type File Description Filename Test Report Test Report report.pdf Operational Description Technical Description descri.pdf Test Report Bandwidth Plot bw.pdf Test Report Spurious Emissions cspurious.pdf Test Report Bandedge Plot be.pdf RF Exposure Info SAR Report sar report. pdf External Photos External Photo external photos.pdf Internal Photos Internal Photo internal photos.pdf ID Label/Location Info Label Artwork and Location label.pdf Cover Letter Label Location Justification justification.pdf Block Diagrams Block Diagram block.pdf Schematics Circuit Diagram circuit.pdf User Manual User Manual manual.pdf Part List/Tune Up Info Tune Up Procedure tuneup.pdf Part List/Tune Up Info Part List partlist.pdf Cover Letter Letter of Agency letter of agency.pdf Cover Letter Confidentiality Request request.pdf INTERTEK TESTING SERVICES TRF: FCC 22H&24E_b Test Report Number: 141127003SZN-006 FCC ID: QISY360-U03 Table of Contents 1.0 Summary of Test Results..................................................................................................................................1 1.1 Statement of Compliance................................................................................................................................1 2.0 General Description............................................................................................................................................2 2.1 Product Description...........................................................................................................................................2 2.2 Test Methodology..............................................................................................................................................3 2.3 Test Facility........................................................................................................................................................3 3.0 System Test Configuration................................................................................................................................4 3.1 Justification.........................................................................................................................................................4 3.2 Details of EUT and Description of Accessories..............................................................................................6 3.3 Measurement Uncertainty.................................................................................................................................6 3.4 Equipment Modification.....................................................................................................................................6 4.0 Test Results..........................................................................................................................................................7 4.1 Channels for Cellular Service and Broadband PCS Services (FCC Part 22.905, Part 24.229)................7 4.2 RF Power Output (FCC Part 2.1046, 22.913 & 24.232)................................................................................9 4.3 Occupied Bandwidth (FCC Part 2.1049).....................................................................................…

Text truncated - open the document above for the full version.