QISY520-U33WCDMA Digital Mobile Phone

1 Dual-Card Dual-Standby Your mobile phone supports dual-card dual-stand by mode, which can signif icantly reduce power consumpt ion and increase your phone's standby t ime. Note that two restrict ions exist:  When you make calls using one SIM card, the other SIM card is disabled. For example, when you make calls using SIM card 1, SIM card 2 cannot be used to answer calls or access the Internet. If someone calls SIM card 2, the caller will hear a voice message like "The subscriber you dialed is out of the service zone" or "The subscriber you dialed is not able to answer your call, please try again later." This is because your mobile phone cannot access the network with both SIM cards at the same t ime and has nothing to do with your service provider's network condit ion. It is recommended that you subscribe to services such as voicemail or missed-call reminders from your service provider to avoid the inconvenience caused by missed calls.  When you are using one SIM card's data services, you can receive calls and messages using the other SIM card, but data services will be interrupted. For example, when SIM card 1's data services are in use, you can use SIM card 2 for calling and messaging, but SIM card 1's data services will be interrupted as a result. When the call using SIM card 2 is terminated, or the message is received or sent, you can resume using SIM card 1's data services. 2 Gett ing to know your phone Thank you for choosing the HUAWEI smartphone. First, let's take a look at a few basics. Press and hold the power button to power on your phone. After your phone is powered up, you can use the power button to turn the screen off and on. 3 Preparing your phone To insert the SIM card, the battery and a microSD card please perform the steps shown in the following f igures. Your phone is shipped with the battery part ially charged. It is recommended that you fully charge the battery before using it for the f irst t ime. When fastening the battery cover, fasten its upper part f irst and then press down the lower part unt il completely fastened. 4 Dual-Card Management Your mobile phone supports access to both WCDMA and GSM networks. Follow the onscreen instruct ions or the quick start guide to install SIM cards. 1. On the home screen, touch > . 2. Touch SIM management to activate the SIM cards. 5 Locking and unlocking the screen When you are not using your phone, press the power button to turn off the screen. After being idle for a specif ied period of t ime, your phone automat ically locks its screen. Follow the onscreen instruct ions and drag to unlock the screen or open an applicat ion. 6 Making a call Touch to open the dialer. You can dial a phone number directly or touch to choose a contact. You can also touch a phone number in places like messages, email and webpages to make a call. To answer an incoming call, drag to . 7 Sending messages Touch to open Messaging. Adding a photo or audio clip to a text message turns it into a mult imedia message. You can also save attachments from mult imedia messages. 8 Taking a photo or video Touch to open Camera. In photo mode, touch to take a photo. In video mode, frame the scene and touch to record a video. Your phone does not support autofocus and may not be able to properly scan QR codes. 9 Listening to music Touch > to open Play Music. You can copy songs to your phone and immerse yourself with extraordinary audio experience anytime. You can play songs by artist, album and more. 10 Surf ing the web On the home screen, touch > to open Browser. You can start surf ing the web right away using your phone's browser and stay on ball with up-to-date news and informat ion. Your browser supports mult i-page browsing. Touch to switch between pages. 11 Wi-Fi hotspot Your phone can also funct ion as a Wi-Fi hotspot for other devices, sharing its mobile data connect ion. 1. Touch > More... > Tethering & portable hotspot. 2. Touch Wi-Fi hotspot to turn on hotspot. 3. Touch Wi-Fi hotspot > Set up Wi-Fi hotspot, you can name the Wi-Fi hotspot, select an encryption mode, set the key to the Wi-Fi hotspot. 4. On the device you want to use, search for and connect to your phone's Wi-Fi network. By default, the Wi-Fi hotspot turns off after being idle for 5 minutes. 12 Others In certain locat ions or weather condit ions, GPS posit ioning informat ion may not be accurate. Your phone may experience lag when there is insuff icient memory or there are too many applicat ions running in the background. For more help Search for and download the User Guide from http://consumer.huawei.com/en/. Please visit http://consumer.huawei.com/en/support/hotline for recently updated hotline and email address in your country or region. 13 Personal Informat ion and Data Security The use of some functions or third-party applications on your device could result in your personal information and data being lost or becoming accessible to others. Several measures are recommended to help you protect personal and confidential information.  Place your device in a safe area to prevent it from unauthorized use.  Set your device screen to lock and create a password or unlock pattern to open it.  Periodically back up personal informat ion kept on your SIM/USIM card, memory card, or stored in your device memory. If you change to a different device, be sure to move or delete any personal informat ion on your old device.  If you are worried about viruses when you receive messages or emails from a stranger, you can delete them without opening them.  If you use your device to browse the Internet, avoid websites that might pose a security risk to avoid theft of your personal informat ion.  If you use services such as Wi-Fi tether or Bluetooth, set passwords for these services to prevent unauthorized access. When these services are not in use, turn them off.  Install or upgrade device security software and regularly scan for viruses.  Be sure to obtain third-party applicat ions from a legit imate…

Text truncated - open the document above for the full version.

文档名称 文档密级 2014-08-05 华为保密 信息,未经授权禁止扩散 第1页, 共1页 To whom it may concern, Letter of Agency I, an officer of HUAWEI TECHNOLOGIES CO.,LTD do hereby authorize Intertek Testing Services (Mr. Shawn Xing) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 22&24 of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2007) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Zhang xinghai EMC Laboratory Manager

Huawei Technologies Co.,Ltd. Federal Communications Commission 2014-08-05 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: QIS Y520-U33 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. ***************************************************************************** In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the Commission withholds the following documents from public viewing until 2014-12-30: External Photos Internal Photos Test Setup Photos User Manual ****************************************************************************** It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C E- mail: [email protected] Tel: 0086-0755-28970299 Fax: 0086-0755-89650226

文档名称 文档密级 2014-8-12 华为保密信息,未经授权禁止扩散 第1页, 共1页 Declaration Manufacturer/Application:Huawei Technologies Co.,Ltd FCC ID: QISY520-U33 I declare that the shielded USB cable used in the test will be marketed with the EUT. Yours sincerely, Product Manager: Email: [email protected]

HUAWEI Y-U3 WCDMA Digital Mobile Phone 文档密级 2014-8-6 华为保密信息,未经授权禁止扩散 第1页, 共1页 Statement We, Huawei Technologies Co.,Ltd., states that our device, FCC ID: QISY520-U33, The label is put inside the battery compartment But the battery will not be placed in the battery compartment when delivery, the label is visible to the users as they purchase the products and install the battery. For and Behalf of: Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager Address: Administration Building, Headquarters of Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C E-mail: [email protected] Tel: 0086-0755-28970299 Fax: 0086-0755-89650226

SIZE：48 (mm)* 56(mm)

Report No.: RXA1407-0176SAR01R1 Page 1 of 232 TESTING No. L2264 SAR TEST REPORT Product Name WCDMA Digital Mobile Phone Model Name HUAWEI Y520-U33 Brand Name HUAWEI FCC ID QISY520-U33 Applicant Huawei Technologies Co., Ltd. Manufacturer Huawei Technologies Co., Ltd. Date of issue August 11, 2014 TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 2 of 232 GENERAL SUMMARY Reference Standard(s) FCC 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices ANSI C95.1, 1992: Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.(IEEE Std C95.1-1991) IEEE Std 1528™-2003: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. KDB 865664 D01 SAR measurement 100 MHz to 6 GHz v01r03: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 447498 D01 Mobile Portable RF Exposure v05r02: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 648474 D04 Handset SAR v01r02: SAR Evaluation Considerations for Wireless Handsets. KDB 941225 D01 SAR test for 3G devices v02: SAR Measurement Procedures CDMA 20001x RTT, 1x Ev-Do, WCDMA, HSDPA/HSPA KDB 941225 D02 HSPA and 1x Advanced v02r02 SAR Guidance for HSPA, HSPA+, DC-HSDPA and 1x-Advanced KDB 941225 D03 Test Reduction GSM_GPRS_EDGE v01:Recommended SAR Test Reduction Procedures for GSM/GPRS/EDGE KDB 941225 D06 Hotspot Mode SAR v01r01: SAR Evaluation Procedures for Portable Devices with Wireless Router Capabilities KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards for the tested bands only. General Judgment: Pass Comment The test result only responds to the measured sample. Approved by Weizhong Yang Director Revised by Minbao Ling SAR Manager Performed by Yi Zhang SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 3 of 232 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the Test Report ....................................................................................................... 5 1.2. Testing Laboratory ................................................................................................................ 5 1.3. Applicant Information ............................................................................................................ 6 1.4. Manufacturer Information ...................................................................................................... 6 1.5. Information of EUT ................................................................................................................ 7 1.6. EUT Antenna Locations ........................................................................................................ 9 1.7. The Maximum Reported SAR 1g .......................................................................................... 10 1.8. Test Date ............................................................................................................................ 11 2. SAR Measurements System Configuration ................................................................................ 12 2.1. SAR Measurement Set-up .................................................................................................. 12 2.2. DASY5 E-field Probe System ............................................................................................. 13 2.2.1. EX3DV4 Probe Specification ....................................................................................... 13 2.2.2. E-field Probe Calibration .............................................................................................. 14 2.3. Other Test Equipment ......................................................................................................... 14 2.3.1. Device Holder for Transmitters .................................................................................... 14 2.3.2. Phantom ...................................................................................................................... 15 2.4. Scanning Procedure ........................................................................................................... 15 2.5. Data Storage and Evaluation .............................................................................................. 17 2.5.1. Data Storage ................................................................................................................ 17 2.5.2. Data Evaluation by SEMCAD ...................................................................................... 17 3. Laboratory Environment ............................................................................................................. 19 4. Tissue-equivalent Liquid ............................................................................................................ 20 4.1. Tissue-equivalent Liquid Ingredients ................................................................................... 20 4.2. Tissue-equivalent Liquid Properties .................................................................................... 22 5. System Check ............................................................................................................................ 23 5.1. Description of System Check .............................................................................................. 23 5.2. System Check Results ..........................................................…

Text truncated - open the document above for the full version.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 155 of 232 802.11b Left Cheek High (Battery 4) Date: 7/19/2014 Communication System: UID 0, 802.11b (0); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 1.824 S/m; ε r = 38.584; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Left Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3677; ConvF(7.64, 7.64, 7.64); Calibrated: 11/28/2013 Electronics: DAE4 Sn1317; Calibrated: 1/16/2014 Phantom: SAM 2; Type: SAM; Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Left Cheek Middle/Area Scan (81x131x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 0.185 W/kg Left Cheek Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 5.040 V/m; Power Drift = -0.08 dB Peak SAR (extrapolated) = 0.253 W/kg SAR(1 g) = 0.130 W/kg; SAR(10 g) = 0.053 W/kg Maximum value of SAR (measured) = 0.167 W/kg Figure 99 Left Hand Touch Cheek 802.11b Channel 11 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 156 of 232 802.11b Back Side High (Battery 1) Date: 7/19/2014 Communication System: UID 0, 802.11b (0); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.009 S/m; ε r = 52.109; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3677; ConvF(7.61, 7.61, 7.61); Calibrated: 11/28/2013 Electronics: DAE4 Sn1317; Calibrated: 1/16/2014 Phantom: SAM 2; Type: SAM; Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Back Side Middle/Area Scan (81x131x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 0.146 W/kg Back Side Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.869 V/m; Power Drift = -0.020 dB Peak SAR (extrapolated) = 0.172 W/kg SAR(1 g) = 0.057 W/kg; SAR(10 g) = 0.024 W/kg Maximum value of SAR (measured) = 0.0684 W/kg Figure 100 Body, Back Side, 802.11b Channel 11 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 157 of 232 802.11b Front Side High (Battery 1) Date: 7/19/2014 Communication System: UID 0, 802.11b (0); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.009 S/m; ε r = 52.109; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3677; ConvF(7.61, 7.61, 7.61); Calibrated: 11/28/2013 Electronics: DAE4 Sn1317; Calibrated: 1/16/2014 Phantom: SAM 2; Type: SAM; Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Front Side Middle/Area Scan (81x131x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 0.0362 W/kg Front Side Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 1.691 V/m; Power Drift = 0.120 dB Peak SAR (extrapolated) = 0.0700 W/kg SAR(1 g) = 0.00627 W/kg; SAR(10 g) = 0.00089 W/kg Maximum value of SAR (measured) = 0.0341 W/kg Figure 101 Body, Front Side, 802.11b Channel 11 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 158 of 232 802.11b Right Edge High (Battery 1) Date: 7/19/2014 Communication System: UID 0, 802.11b (0); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.009 S/m; ε r = 52.109; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3677; ConvF(7.61, 7.61, 7.61); Calibrated: 11/28/2013 Electronics: DAE4 Sn1317; Calibrated: 1/16/2014 Phantom: SAM 2; Type: SAM; Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Right Edge Middle/Area Scan (51x151x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.0292 W/kg Right Edge Middle/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.416 V/m; Power Drift = 0.027 dB Peak SAR (extrapolated) = 0.0270 W/kg SAR(1 g) = 0.00126 W/kg; SAR(10 g) = 0.000142 W/kg Maximum value of SAR (measured) = 0.0265 W/kg Figure 102 Body, Right Edge, 802.11b Channel 11 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 159 of 232 802.11b Top Edge High (Battery 1) Date: 7/19/2014 Communication System: UID 0, 802.11b (0); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.009 S/m; ε r = 52.109; ρ = 1000 kg/m 3 Ambient Temperature:22.3 °C Liquid Temperature: 21.5°C Phantom section: Flat Section DASY5 Configuration: Sensor-Surface: 4mm (Mechanical Surface Detection) Probe: EX3DV4 - SN3677; ConvF(7.61, 7.61, 7.61); Calibrated: 11/28/2013 Electronics: DAE4 Sn1317; Calibrated: 1/16/2014 Phantom: SAM 2; Type: SAM; Measurement SW: DASY52, Version 52.8 (7); SEMCAD X Version 14.6.10 (7164) Top Edge Middle 3/Area Scan (51x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.0214 W/kg Top Edge Middle 3/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 2.679 V/m; Power Drift = 0.107 dB Peak SAR (extrapolated) = 0.0340 W/kg SAR(1 g) = 0.00499 W/kg; SAR(10 g) = 0.00066 W/kg Maximum value of SAR (measured) = 0.0341 W/kg Figure 103 Body, Top Edge, 802.11b Channel 11 TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1407-0176SAR01R1 Page 160 of 232 802.11b Back Side High (Battery 2) Date: 7/19/2014 Communication System: UID 0, 802.11b (0); Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 2.009 S/m; ε r = 52.109; ρ = 1000 kg/m 3 Ambient Tempera…

Text truncated - open the document above for the full version.

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF no.: FCC 15C_Tx_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Huawei Technologies Co.,Ltd Application For Certification FCC ID: QISY520-U33 WCDMA DIGITAL MOBILE PHONE Model: HUAWEI Y520-U33 WiFi Transceiver Report No.: 140710014SZN-003 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [ 10-1-13] Prepared and Checked by: Approved by: Sign on file Jenner Liu Assistant Engineer Andy Yan Senior Project Engineer Date: 15 August 2014 INTERTEK TESTING SERVICE TRF no.: FCC 15C_TX_b FCC ID: QISY520-U33 Report No.: 140710014SZN-003 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: Summary of Tests EXHIBIT 2: General Description EXHIBIT 3: System Test Configuration EXHIBIT 4: Measurement Results EXHIBIT 5: Equipment Photographs EXHIBIT 6: Product Labeling EXHIBIT 7: Technical Specifications EXHIBIT 8: Instruction Manual EXHIBIT 9: Miscellaneous Information EXHIBIT 10: Test Equipment List INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_b FCC ID: QISY520-U33 Report No.: 140710014SZN-003 ii MEASUREMENT/TECHNICAL REPORT Huawei Technologies Co.,Ltd - MODEL: HUAWEI Y520-U33 FCC ID: QISY520-U33 This report concerns (check one) Original Grant X Class II Change Equipment Type: DTS - Part 15 Digital Transmission Systems (WiFi transmitter portion) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until : date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01-13 Edition] provision. Report prepared by: Jenner Liu Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0639 Fax: (86 755) 8614 6751 INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_b FCC ID: QISY520-U33 Report No.: 140710014SZN-003 iii Table of Contents 1.0 Summary of test results ............................................................................... 2 2.0 General Description ................................................................................................ 4 2.1 Product Description ....................................................................................... 4 2.2 Related Submittal(s) Grants .......................................................................... 4 2.3 Test Methodology .......................................................................................... 5 2.4 Test Facility ................................................................................................... 5 3.0 System Test Configuration ................................................................................. 7 3.1 Justification ................................................................................................... 7 3.2 EUT Exercising Software ............................................................................... 7 3.3 Details of EUT and Description of Peripherals ............................................... 7 3.4 Measurement Uncertainty.............................................................................. 8 3.5 Equipment Modification ................................................................................. 8 3.6 Support Equipment List and Description ....................................................... 8 4.0 Measurement Results .......................................................................................... 10 4.1 Maximum Conducted Output Power at Antenna Terminals .......................... 10 4.2 Minimum 6dB RF Bandwidth ....................................................................... 12 4.3 Maximum Power Density ................................................................................ 22 4.4 Out of Band Conducted Emissions ............................................................... 32 4.5 Out of Band Radiated Emissions ................................................................. 45 4.6 Transmitter Radiated Emissions in Restricted Bands ................................... 46 4.7 Field Strength Calculation ............................................................................ 47 4.8 Radiated Spurious Emission ........................................................................... 48 4.9 Conducted Emission ...........................................................…

Text truncated - open the document above for the full version.

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF no.: FCC 15C_Tx_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Huawei Technologies Co.,Ltd Application For Certification FCC ID: QISY520-U33 WCDMA DIGITAL MOBILE PHONE Model: HUAWEI Y520-U33 2.4GHz Transceiver Report No.: 140710014SZN-002 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-13] Prepared and Checked by: Approved by: Sign on file Jenner Liu Assitant Engineer Andy Yan Senior Project Engineer Date: 15 August 2014 INTERTEK TESTING SERVICE TRF no.: FCC 15C_TX_b FCC ID: QISY520-U33 Report No.: 140710014SZN-002 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: Summary of Tests EXHIBIT 2: General Description EXHIBIT 3: System Test Configuration EXHIBIT 4: Measurement Results EXHIBIT 5: Equipment Photographs EXHIBIT …

Text truncated - open the document above for the full version.