QISY600-U351WCDMA Digital Mobile Phone

Quick Start Guide Y600 1 Dual-Card Dual-Standby Your mobile phone supports dual-card dual-standby mode, which can significantly reduce power consumption and increase your phone's standby time. Note that two restrictions exist:  When you make calls using one SIM card, the other SIM card is disabled. For example, when you make calls using SIM card 1, SIM card 2 cannot be used to answer calls or access the Internet. If someone calls SIM card 2, the caller will hear a voice message like "The subscriber you dialed is out of the service zone" or "The subscriber you dialed is not able to answer your call, please try again later." This is because your mobile phone cannot access the network with both SIM cards at the same time and has nothing to do with your service provider's network condition. It is recommended that you subscribe to services such as voicemail or missed-call reminders from your service provider to avoid the inconvenience caused by missed calls.  When you are using one SIM card's data services, you can receive calls and messages using the other SIM card, but data services will be interrupted. For example, when SIM card 1's data services are in use, you can use SIM card 2 for calling and messaging, but SIM card 1's data services will be interrupted as a result. When the call using SIM card 2 is terminated, or the message is received or sent, you can resume using SIM card 1's data services. 2 Getting to know your phone Thank you for choosing the HUAWEI smartphone. First, let's take a look at a few basics. Press and hold the power button to power on your phone. After your phone is powered up, you can use the power button to turn the screen off and on. 3 Preparing your phone To insert a SIM card, the battery and a microSD card please perform the few steps shown in the following figures. Your phone is shipped with the battery partially charged. It is recommended that you fully charge the battery before using it for the first time. 4 Dual-Card Management Your mobile phone supports access to both WCDMA and GSM networks. Follow the onscreen instructions or the quick start guide to install SIM cards. 1. On the home screen, touch > . 2. Touch SIM management to activate the SIM cards. 5 Locking and unlocking the screen When you are not using your phone, press the power button to turn off the screen. After being idle for a specified period of time, your phone automatically locks its screen. Follow the onscreen instructions and drag to unlock the screen or open an application. 6 Managing contacts On the home screen, touch > to open Contact. Touch the tab page to group your contacts for easier management. 7 Making a call On the home screen, touch > to open the dialer. You can dial a phone number directly or touch to choose a contact. You can also touch a phone number in places like messages, email and webpages to make a call. To answer an incoming call, drag to . 8 Sending messages On the home screen, touch > to open Messaging. Adding a photo or audio clip to a text message turns it into a multimedia message. You can also save attachments from multimedia messages. 9 Taking a photo or video On the home screen, touch > to open Camera. Touch to take a photo. Frame the scene and touch to record a video. 10 Listening to music On the home screen, touch > to open Play Music You can play songs by Listen Now, My Library and Playlists. You can also mark your songs to add them to the playlist. 11 Surfing the web On the home screen, touch > to open Browser. You can start surfing the web right away using your phone's browser and stay on ball with up-to-date news and information. Your browser supports multi-page browsing. Touch to switch between pages. 12 Personal information and data security The use of some functions or third-party applications on your device could result in your personal information and data being lost or becoming accessible to others. Several measures are recommended to help you protect personal and confidential information.  Place your device in a safe area to prevent it from unauthorized use.  Set your device screen to lock and create a password or unlock pattern to open it.  Periodically back up personal information kept on your SIM/USIM card, memory card, or stored in your device memory. If you change to a different device, be sure to move or delete any personal information on your old device.  If you are worried about viruses when you receive messages or emails from a stranger, you can delete them without opening them.  If you use your device to browse the Internet, avoid websites that might pose a security risk to avoid theft of your personal information.  If you use services such as Wi-Fi tether or Bluetooth, set passwords for these services to prevent unauthorized access. When these services are not in use, turn them off.  Install or upgrade device security software and regularly scan for viruses.  Be sure to obtain third-party applications from a legitimate source. Downloaded third-party applications should be scanned for viruses. 13  Install security software or patches released by Huawei or third-party application providers.  Some applications require and transmit location information. As a result, a third-party may be able to share your location information.  Your device may provide detection and diagnostic information to third-party application providers. Third party vendors use this information to improve their products and services.  If you have concerns about the security of your personal information and data, please contact [email protected]. For more help Want to obtain the user guide? Search for and download the User Guide from http://consumer.huawei.com/en/. Please visit http://consumer.huawei.com/en/support/hotline/ for recently updated hotline and email address in your country or region. 14 Legal notice Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved. Trademarks and permissions , , and are trademarks or registered trademarks of Hua…

Text truncated - open the document above for the full version.

1 13/12/2013 To whom it may concern, Letter of Agency I, an officer of HUAWEI TECHNOLOGIES CO., LTD. do hereby authorize Intertek Testing Services (Mr. Shawn Xing) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under FCC Part 15 and FCC Part 22&24 of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2007) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Zhang Xinghai EMC Laboratory Manager

INTERTEK TESTING SERVICES External Photos: INTERTEK TESTING SERVICES

HUAWEI Y600-U351 WCDMA Digital Mobile Phone SECRET 2014-3-18 Page1, Total2 Label & Label Location： HUAWEI Y600-U351 WCDMA Digital Mobile Phone SECRET 2014-3-18 Page2, Total2

INTERTEK TESTING SERVICES Internal photos INTERTEK TESTING SERVICES INTERTEK TESTING SERVICES INTERTEK TESTING SERVICES INTERTEK TESTING SERVICES

Picture1：Head Left Cheek Mode Picture2：Head Left Tilt Mode Picture3：Head Right Cheek Mode Picture4：Head Right Tilt Mode Picture5：Body Phantom Mode Picture6：Body Ground Mode Picture7：Body Left Mode Picture8：Body Right Mode Picture9：Body Top Mode Picture10：Body Bottom Mode

Full SAR TEST REPORT No. 2014SAR0039-1 For Client : Huawei Technologies Co., Ltd. Production : WCDMA Digital Mobile Phone Model Name : HUAWEI Y600-U351 Hardware Version: MOLY.WR8.W1315.MD.WG.MP.V11.P4 . Software Version: Y600-U151V100R001C00B007 Issued date: 2014-03-18 FCC ID: QISY600-U351 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of ECIT Shanghai. Test Laboratory: ECIT Shanghai, East China Institute of Telecommunications Add: 7F, G Area, No.668, Beijing East Road, Huangpu District, Shanghai, P. R. China Tel: (+86)-021-63843300, E-Mail: [email protected] Page 2 of 214 Revision Version Report Number Revision Date Memo 2014SAR0039-1 00 2014/03/18 Initial creation of test report No. 2014SAR0039-1 Page 3 of 214 CONTENTS 1 Test Laboratory .......................................................................................................................... 6 1.1 Testing Location .............................................................................................................................. 6 1.2 Testing Environment ....................................................................................................................... 6 1.3 Project Data ..................................................................................................................................... 6 1.4 Signature .......................................................................................................................................... 6 2 Statement of Compliance .......................................................................................................... 7 3 Client Information ...................................................................................................................... 9 3.1 Applicant Information ..................................................................................................................... 9 3.2 Manufacturer Information ............................................................................................................... 9 4 Equipment Under Test (EUT) and Ancillary Equipment (AE) ............................................... 10 4.1 About EUT ...................................................................................................................................... 10 4.2 Internal Identification of EUT used during the test ..................................................................... 11 4.3 Internal Identification of AE used during the test ....................................................................... 11 5 TEST METHODOLOGY ............................................................................................................ 12 5.1 Applicable Limit Regulations ....................................................................................................... 12 5.2 Applicable Measurement Standards ........................................................................................... 12 6 Specific Absorption Rate (SAR) ............................................................................................. 14 6.1 Introduction.................................................................................................................................... 14 6.2 SAR Definition ............................................................................................................................... 14 7 Tissue Simulating Liquids ...................................................................................................... 15 7.1 Targets for tissue simulating liquid ............................................................................................. 15 7.2 Dielectric Performance ................................................................................................................. 15 8 System verification .................................................................................................................. 19 8.1 System Setup ................................................................................................................................. 19 8.2 System Verification ....................................................................................................................... 20 9 Measurement Procedures ....................................................................................................... 21 9.1 Tests to be performed ................................................................................................................... 21 9.2 General Measurement Procedure ................................................................................................ 22 9.3 WCDMA Measurement Procedures for SAR ............................................................................... 23 9.4 Bluetooth & Wi-Fi Measurement Procedures for SAR............................................................... 24 9.5 Power Drift ..................................................................................................................................... 25 10 Conducted Output Power ...................................................................................................... 26 No. 2014SAR0039-1 Page 4 of 214 10.1 Manufacturing tolerance ............................................................................................................. 26 10.2 GSM Measurement result ........................................................................................................... 31 10.3 WCDMA Measurement result ..................................................................................................... 33 10.4 Wi-Fi and BT Measurement result ............................................................................................. 34 11 Simultaneous TX SAR Considerations ..........................................................…

Text truncated - open the document above for the full version.

No. 2014SAR0039-1 Page 162 of 214 ANNEX G Probe and DAE Calibration Certificate No. 2014SAR0039-1 Page 163 of 214 No. 2014SAR0039-1 Page 164 of 214 No. 2014SAR0039-1 Page 165 of 214 No. 2014SAR0039-1 Page 166 of 214 No. 2014SAR0039-1 Page 167 of 214 No. 2014SAR0039-1 Page 168 of 214 No. 2014SAR0039-1 Page 169 of 214 No. 2014SAR0039-1 Page 170 of 214 No. 2014SAR0039-1 Page 171 of 214 No. 2014SAR0039-1 Page 172 of 214 No. 2014SAR0039-1 Page 173 of 214 No. 2014SAR0039-1 Page 174 of 214 No. 2014SAR0039-1 Page 175 of 214 No. 2014SAR0039-1 Page 176 of 214 No. 2014SAR0039-1 Page 177 of 214 No. 2014SAR0039-1 Page 178 of 214 No. 2014SAR0039-1 Page 179 of 214 No. 2014SAR0039-1 Page 180 of 214 No. 2014SAR0039-1 Page 181 of 214 No. 2014SAR0039-1 Page 182 of 214 No. 2014SAR0039-1 Page 183 of 214 No. 2014SAR0039-1 Page 184 of 214 No. 2014SAR0039-1 Page 185 of 214 No. 2014SAR0039-1 Page 186 of 214 No. 2014SAR0039-1 Page 187 of 214 ANNEX H Dipole Calibration Certificate No. 2014SAR0039-1 Page 188 of 214 No. 2014SAR0039-1 Page 189 of 214 No. 2014SAR0039-1 Page 190 of 214 No. 2014SAR0039-1 Page 191 of 214 No. 2014SAR0039-1 Page 192 of 214 No. 2014SAR0039-1 Page 193 of 214 No. 2014SAR0039-1 Page 194 of 214 No. 2014SAR0039-1 Page 195 of 214 No. 2014SAR0039-1 Page 196 of 214 No. 2014SAR0039-1 Page 197 of 214 No. 2014SAR0039-1 Page 198 of 214 No. 2014SAR0039-1 Page 199 of 214 No. 2014SAR0039-1 Page 200 of 214 No. 2014SAR0039-1 Page 201 of 214 No. 2014SAR0039-1 Page 202 of 214 No. 2014SAR0039-1 Page 203 of 214 No. 2014SAR0039-1 Page 204 of 214 No. 2014SAR0039-1 Page 205 of 214 No. 2014SAR0039-1 Page 206 of 214 No. 2014SAR0039-1 Page 207 of 214 No. 2014SAR0039-1 Page 208 of 214 No. 2014SAR0039-1 Page 209 of 214 No. 2014SAR0039-1 Page 210 of 214 No. 2014SAR0039-1 Page 211 of 214

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample ma y be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF no.: FCC 15C_Tx_b In t ertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com H u a wei Technologies Co.,Ltd Application For Certification FCC ID: QISY600-U351 WCDMA Digital Mobile Phone Model: HUAWEI Y600-U351 WiFi Transceiver Report No.: 140311039SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-13] Pr epared and Checked by: Approved by: Sign on file Eason He Engineer Billy Li Supervisor Date: March 18, 2014 INTERTEK TESTING SERVICE TRF no.: FCC 15C_TX_b FCC ID: QISY600-U351 Report No.: 140311039SZN-001 i LIST OF EXHIBITS I NTRODUCTION EXHIBIT 1: Summary of Tests EXHIBIT 2: General Description EXHIBIT 3: System Test Configuration EXHIBIT 4: Measurement Results EXHIBIT 5: Equipment Photographs EXHIBIT 6: Product Labeling EXHIBIT 7: Technical Specifications EXHIBIT 8: Instruction Manual EXHIBIT 9: Miscellaneous Information EXHIBIT 10: Test Equipment List INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_b FCC ID: QISY600-U351 Report No.: 140311039SZN-001 ii MEASUREMENT/TECHNICAL REPORT H u a wei Technologies Co.,Ltd - MODEL: HUAWEI Y600-U351 FCC ID: QISY600-U351 This report concerns (check one) Original Grant X Class II Change Equipment Type: DTS - Part 15 Digital Transmission Systems (WiFi transmitter portion) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until : date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01-13 Edition] provision. Report prepared by: Eason He Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0714 Fax: (86 755) 8614 6751 INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_b FCC ID: QISY600-U351 Report No.: 140311039SZN-001 iii Table of Contents 1 . 0 Summary of test results...............................................................................2 2.0 General Description................................................................................................4 2.1 Product Description.......................................................................................4 2.2 Related Submittal(s) Grants ..........................................................................4 2.3 Test Methodology..........................................................................................5 2.4 Test Facility...................................................................................................5 3.0 System Test Configuration .................................................................................7 3.1 Justification ...................................................................................................7 3.2 EUT Exercising Software...............................................................................7 3.3 Details of EUT and Description of Peripherals...............................................8 3.4 Measurement Uncertainty..............................................................................8 3.5 Equipment Modification .................................................................................8 3.6 Support Equipment List and Description.......................................................8 4.0 Measurement Results .......................................................................................... 10 4.1 Maximum Conducted Output Power at Antenna Terminals..........................10 4.2 Minimum 6dB RF Bandwidth.......................................................................16 4.3 Maximum Power Density................................................................................26 4.4 Out of Band Conducted Emissions ...............................................................36 4.5 Out of Band Radiated Emissions.................................................................61 4.6 Transmitter Radiated Emissions in Restricted Bands...................................62 4.7 Field Strength Calculation............................................................................63 4.8 Radiated Spurious Emission...........................................................................64 4.9 Conducted Emission.......................................................................................78 4.10 Radiated …

Text truncated - open the document above for the full version.

Radiated Photos:

Conducted photos: