QNP-AMC30Door Sensor UL

ITALIANO
NON fissare l’AMC30 finché non supera il Test di Posizionamento. L'AMC30 è un Contatto Magnetico via Radio dotato di un ingres- so ausiliario per il collegamento di un Contatto per Tapparelle. Identificazione delle parti Per l’dentificazione delle parti fare riferimento alla Fig. 1. 1.Staffa 2.Fori per il fissaggio della staffa 3.Dente per sganciare la staffa 4.Fondo 5.Batteria 6.Spia batteria bassa 7.Deviatore antisabotaggio 8.Tacche per l’allineamento del magnete 9.Magnete 10.Morsettiera 11.Ponticelli per la programmazione Apertura Premere nella parte superiore dell’AMC30 e sollevare il coperchio. Installazione batteria Prestare attenzione quando viene installata la batteria e ri- spettare la polarità (Fig. 1). Usare SOLO una batteria al Litio, Panasonic CR123A.
La batteria a corredo dell’AMC30 è da considerarsi mate- riale di consumo e, quindi, esclusa dalla garanzia. Posizionamento Scegliere la posizione per installare l’AMC30.
I segnali radio possono essere attenuati da oggetti me- tallici, come porte di metallo e grandi specchi. Assicurar- si che questi tipi di oggetti non si trovino tra l’AMC30 e il ricevitore poiché essi possono interferire con il corretto funzionamento dell’AMC30. Configurazione e Test di Posizionamento Il numero di serie a 6 cifre presente sull’AMC30 è relativo al contatto magnetico. Il numero di serie dell’ingresso ausiliario si ottiene sommando 1 al numero di serie presente sull’AMC30. Per esempio, se il numero di serie sull’AMC30 è 211117, il numero di serie per il contatto magnetico è 211117, mentre il numero di serie dell’ingresso ausiliario è 211118. Tenere presente che: A+1=B; B+1=C; C+1=D; D+1=E; E+1=F; F+1=0, con l’aumento di una unità della cifra immediatamen- te a sinistra (per esempio 21111F+1=211120). Eseguire il Test di Posizionamento come descritto sulle istru- zioni del ricevitore.
Per provocare una trasmissione, allontanare il magente dall’AMC30. Fissaggio 1.Posizionare la staffa nel punto determinato tramite il Test di Posizionamento e fissarla al telaio tramite le viti fornite. 2.Agganciare il rilevatore alla staffa. Per sganciare il rilevatore dalla staffa: rimuovere il coper- chio; premere il dente 3 (Fig. 1) con un piccolo giravite e fare scorrere il rilevatore verso il basso. 3.Allineare un lato del magnete con la tacca presente sul corpo dell’AMC30 (Fig. 1). 4.Fissare il magnete a 1,27 cm al massimo dall’AMC30, tramite le viti fornite. Se necessario, usare i distanziatori in dotazione (Fig. 2). ENGLISH
Do NOT permanently mount the AMC30 until the Place- ment Test has been successfully passed. The AMC30 is a wireless door/window contact. Il also pro- vides an auxiliary input to connect a Roller-Blind Contact. Parts identification 1.Mounting bracket 2.Holes to fix the bracket 3.Tab to release the bracket 4.Back 5.Battery 6.Low-Battery indicator 7.Tamper switch 8.Notch for magnet alignement 9.Magnet 10.Terminal board 11.Programming jumpers Opening Remove the cover by pressing on the end notch to lift top cover. Install Battery Use care when installing the battery and observe the correct polarity (see Fig. 1). Use ONLY the Panasonic CR123A lithium battery.
The warranty does not apply to the battery of the AMC30. Position Transmitter Select the location where the AMC30 is to be mounted.
RF signals can be affected by metal objects, including metal doors or large mirrors. Ensure that these types of objects are not located between the AMC30 and the receiver as it can interfere with the proper operation of the AMC30. Enrolling and Placement The 6 digit serial number located on the AMC30 is for the door/window contact. The serial number for the auxiliary input is the serial number located on AMC30 + 1. For example, if the serial number printed on the AMC30 is 211117, then the door/window contact serial number is 211117, while the auxiliary input serial number is 211118. If the last digit is a letter then A+1=B; B+1=C; C+1=D; D+1=E; E+1=F; F+1=0, and the next left digit increases by one (for example 21111F+1=211120). Perform the Placement Test to ensure that the selected loca- tion is in range of the wireless receiver (see receiver Instal- lation Manual for instructions).
Create a transmission by moving the magnet away from the AMC30. Mounting the AMC30 1.Place the mounting bracket in the position determined in the Placement Test. Secure the bracket to the door frame using the two screws provided. 2.“Snap” the sensor in place. To release bracket: remove the front cover; push the tab (see Fig. 1) with a small screwdriver and slide the AMC30 down. 3.Align one end of the magnet with the notch on the side of AMC30 housing (See Fig. 1). 4.Mount the magnet a maximum of 1/2" (1.27 cm) from the AMC30 using the screws provided. If necessary use the spacers provided (see Fig. 2). FRANÇAIS
Fixer le AMC30 seulement après qu'il a passé positive- ment le Test de Positionnement. Le AMC30 est un Contact Magnétique Radio avec une en- trée auxiliaire pour la conexion d'un Volet Roulant. Identification des elements 1.Support 2.Trous de fixation 3.Blocage 4.Embase 5.Pile 6.Indicateur de pile basse 7.Autoprotection 8.Encoches pour l'alignement de l'aimant 9.Aimant 10.Bornier 11.Pontets pour la programmation Ouvrir le couvercle Pour enlever le couvercle, presser dans la partie supérieure de l'AMC30. Installer la pile Bien respecter la polarité de la pile (voir Fig. 1). Utiliser seulement une pile Panasonic CR123A.
La garantie ne s’applique pas à la pile du AMC30. Positionnement du transmetteur Selectionner le lieu ou sera installer le AMC30.
Les signaux RF peuvent être dérangés par objets du métal ou portes du métal ou grands miroirs. Assure que ces types d'objets ne sont pas localisés entre le AMC30 et le receveur pour éviter mauvais fonctionnements du detecteur. Configuration et Positionnement Le 6 chiffre du numéro de série localisé sur l'AMC30 est pour le contact de la porte ou de la fenêtre. Le numéro de série pour l'entrée auxiliaire est le num…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.60327401-RP1 External Photo Compliance Certification Services Inc. Report No.60327401-RP1

g Company : Secure Wireless, Inc. Model: AMC 30 Product : DOOR SENSOR UL Label Here DOOR SENSOR UL Model No: AMC 30 FCC ID：QNP-AMC30 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference and [2] this device must accept any interference received, including interference that may cause undesired operation. S/N： Made in Taiwan

Compliance Certification Services Inc. Report No.60327401-RP1 Internal Photo Compliance Certification Services Inc. Report No.60327401-RP1 Compliance Certification Services Inc. Report No.60327401-RP1

Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: April 19, 2006 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 33 FCC 47 CFR PART 15 SUBPART C TEST REPORT For DOOR SENSOR UL Model: AMC 30 Issued to Secure Wireless, Inc. 5817 Dryden Place #104 Carlsbad, CA 92008 Issued by Compliance Certification Services Inc. Ta i n a n L a b . No. 8, Jiu Cheng Ling, Jiaokeng Village,Sinhua Township, Tainan Hsien 712, Taiwan R.O.C. TEL: 886-6-580-2201 FAX: 886-6-580-2202 Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: April 19, 2006 Page 2 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION............................................................................................. 3 2. EUT DESCRIPTION .................................................................................................................... 4 3. TEST METHODOLOGY ............................................................................................................. 5 3.1 EUT CONFIGURATION.............................................................................................................. 5 3.2 EUT EXERCISE......................................................................................................................... 5 3.3 GENERAL TEST PROCEDURES.................................................................................................. 5 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .............................................. 6 3.5 DESCRIPTION OF TEST MODES................................................................................................. 6 4. INSTRUMENT CALIBRATION................................................................................................. 7 5. FACILITIES AND ACCREDITATIONS ................................................................................... 8 5.1 FACILITIES.............................................................................................................................. 8 5.2 EQUIPMENT............................................................................................................................. 8 5.3 LABORATORY ACCREDITATIONS AND LISTING....................................................................... 8 5.4 TABLE OF ACCREDITATIONS AND LISTINGS............................................................................ 9 6. SETUP OF EQUIPMENT UNDER TEST ................................................................................ 10 6.1 SETUP CONFIGURATION OF EUT............................................................................................ 10 6.2 SUPPORT EQUIPMENT............................................................................................................ 10 7. FCC PART 15.231 REQUIREMENTS...................................................................................... 11 7.1 20 DB BANDWIDTH .......................................................................................................... 11 7.2 LIMIT OF TRANSMISSION TIME.............................................................................................. 13 7.3 DUTY CYCLE ..................................................................................................................... 15 7.4 RADIATED EMISSIONS........................................................................................................... 18 7.5 POWERLINE CONDUCTED EMISSIONS.................................................................................... 27 Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: April 19, 2006 Page 3 1. TEST RESULT CERTIFICATION Applicant: Secure Wireless, Inc. 5817 Dryden Place #104 Carlsbad, CA 92008 Manufacture: Vision Automobile Electronics Industrial Co., Ltd. NO. 17 ALLEY 92, LANE 189, SEC. 1, AN CHUNG RD., TAINAN, TAIWAN, R.O.C. Equipment Under Test: DOOR SENSOR UL Model Number: AMC 30 Date of Test: April 14, 2006 ~ April 18, 2006 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.207, 15.209 and Part 15.231. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: April 19, 2006 April 19, 2006 Alex Chiu Jeter Wu Manager Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: April 19, 2006 Page 4 2. EUT DESCRIPTION Product DOOR SENSOR UL Model Number AMC 30 Model Difference N/A Power Supply Powered by battery (DC 3V) Frequency Range 433.92MHz Number of Channels Remote Controller: 433.92 MHz 50K : 1 Channel Antenna Specification -8dBm Temperature Range 0°C ~ +55°C Remark: This submittal(s) (test report) is intended for FCC ID: QNP-AMC30 filing to comply with Section 15.207, 15.209 and 15.231 of the FCC Part 15, Subpart C Rules. Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: April 19, 2006 Page 5 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 (2001) and FCC CFR 47 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.231. 3.…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: March 23, 2006 Page 28 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos (For TX) (1) X-axis Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: March 23, 2006 Page 29 Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: March 23, 2006 Page 30 (2) Y-axi Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: March 23, 2006 Page 31 Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: March 23, 2006 Page 32 (3) Z-axis Compliance Certification Services Inc. Report No.: 60327401-RP1 FCC ID: QNP-AMC30 Date of Issue: March 23, 2006 Page 33 End of report