QNP915SRNDEVICE CONTROLLER

Product Description The AT&T model number SW-ATT-SRN is a proprietary 915MHz wireless siren that is capable of annunciating alarms and keypad chirps. The DLC sends messages to the SW-ATT- SRN via a proprietary 915MHz radio protocol to command the SW-ATT-SRN to generate tones and pre-programmed alarm sequences through its annunciator, including a temporal 3 - alarm (three short beeps then silence repeating) when a smoke alarm is activated and a temporal 4 alarm (four short beeps then silence repeating) when the CO alarm is activated. In addition the siren beeps during an intrusion alarm. Installing/Replacing Batteries The siren has two (2) non-rechargeable 3V CR123A batteries that provide twenty-four (24) hour battery backup. The batteries can be replaced by opening the battery compartment located on the rear of the unit. Installing the Siren Follow these steps to install the Siren: 1. Turn the Siren to its underside and remove the Phillips Head screw at the bottom to open battery compartment cover. 2. Remove the battery compartment cover. 3. Insert two (2) non-rechargeable CR123A batteries. 4. NOTE: Ensure that polarity of the batteries is correct during installation 5. Replace the battery compartment cover and the Phillips head screw. 6. Plug the unit into the lower socket of an AC outlet and install a retaining screw into the plastic tab located at the top of the unit to secure the unit to the AC outlet. The LED shows the system status, as follows: Solid Green—unit is AC powered and backup battery is good. Blinking Green—unit is not AC powered and is operating on backup batteries. Solid Red—unit is AC powered and the backup battery needs to be replaced. Off—unit is not AC powered and backup battery has failed. Discovering and Registering the Siren Follow these steps to discover and register the siren: 1. Place the DLC into Discovery Mode in DLD. 2. Plug in the siren and once it has powered make it discoverable by pressing the small white learn button located on the side of the unit. 3. Confi rm that the siren has been discovered in DLD. 4. Label the siren in DLD. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. Ľexploitation est autorisée aux deux conditions suivantes: (1) ľappareil ne doit pas produire de brouillage, et (2) ľutilisateur de ľappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible ďen compromettre le fonctionnement. FCC Compliance Statement This device complies with FCC Rules and Regulations as Part 15 devices as well as Industry Canada license exempt RSS Rules and Regulations. Operation is subject to the following two (2) conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. WARNING!WARNING! The polarity of the battery must be observed. Improper handling The polarity of the battery must be observed. Improper handling of lithium batteries may result in heat generation, explosion or fi re of lithium batteries may result in heat generation, explosion or fi re which may lead to personal injuries. Replace only with the same which may lead to personal injuries. Replace only with the same as recommended by the manufacturer. Use of another battery may as recommended by the manufacturer. Use of another battery may present a risk of fi represent a risk of fi re or corrosion.or corrosion. CAUTION! Batteries should not be recharged, disassembled, in heat above 100° C (212°F) or disposed of in fi re. Disposal of used batteries must be made in accordance with the waste recovery and recycling regulations in your area. Notice to users in California—This Perchlorate warning applies only to Manganese Dioxide Lithium cells sold or distributed only in California, USA. Percolate Material Special handling may apply. See www.dtsc.ca.gov.hazardouswaste/perchlorate. Copyright © 2013 Linear LLC. 234731X5 LISTED SW-ATT-SRN RTL 41806 Installation Instructions

Secure Wireless Inc. 5817 Dryden Place Suite D Carlsbad, CA 92008 Secure Wireless, Inc. 5817 Dryden Place Suite D Carlsbad, CA 92008 01 January 2013 Federal Communications Commission Authorization and Evaluation Division FCC ID: QNP915SRN Authority to Act as Agent On our behalf, I appoint Tom Tidwell of Nemko USA Inc., 802 N. Kealy Ave., Lewisville, TX 75057-3136, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communication Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Timco Engineering, still resides with Secure Wireless, Inc, 5817 Dryden Place, Suite D, Carlsbad, CA. 92008, USA. This appointment is in effect until December 31, 2013. Sincerely, John W. Kuivinen, P.E. Regulatory Compliance Engineer

LABEL, FCC/DOC, SW-ATT-SRN LINEAR P/N: 233427 X3 MANUFACTURING PROCESS: LABEL, SILKSCREEN, OR PADPRINT LABEL INK: PERMANENT BLACK LABEL MATERIAL: CLEAR ACETATE, ADHESIVE BACKED THICKNESS: .0015" PAD PRINTING INK: BLACK, LINEAR P/N: 213337-002 SCALE: 1-1 2.300" 1.000" SECURE WIRELESS, INC. MODEL; SW-ATT-SRN FCC ID: QNP915SRN I.C.:4676A-915SRN MADE IN CHINA 233427 X3 For installation instructions refer to Manual Number 234731 supplied with this product. This device complies with Part 15 of the FCC and Industry Canada license exempt RSS Standard Rules and Regulations. Operation subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d ́Industrie Canada applicables aux appareils radio exempts de licence. L ́exploitation est autorisée aux deus conditions suivantes: (1) l ́appareil ne doit pas produire de brouillage, et (2) l ́utilisateur de l ́appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d ́en compromettre le fonctionnement. INPUT: 120V 60 Hz 3 Watts

Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC Part 15 Subpart C, 15.249 : 24 January 2013 CERTIFICATION TEST REPORT Report Number: 2012 10221065 EMC Project Number: 10231105 Nex Number: 221065 Applicant: Secure Wireless, Inc. 5817 Dryden Place, Suite D Carlsbad, CA 92008 Equipment Under Test (EUT): ALARM SIREN Model: SW-ATT-SRN FCC ID: QNP915SRN IC: 4676A-915SRN In Accordance With: FCC Part 15 Subpart C, 15.249 IC RSS-210 Issue 8 December 2010 IC RSS-Gen Issue 3 December 2010 Tested By: Nemko USA Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Authorized By: Alan Laudani, EMC/RF Test Engineer Date: O CTOBER 5, 2012 Total Number of Pages: 26 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: QNP915SRN Report Number: 2012 10221065 EMC IC: 4676A-915SRN Specification: FCC Part 15 Subpart C, 15.249 Page 2 of 26 1 Applicant Affirmation John Kuivinen representing Secure Wireless, Inc. hereby affirms: a) That he/she has reviewed and concurs that the test shown in this report are reflective of the operational characteristics of the device for which certification is sought; b) That the device in this test report will be representative of production units; c) That all changes (in hardware and software/firmware) to the subject device will be reviewed. d) That any changes impacting the attributes, functionality or operational characteristics documented in this report will be communicated to the body responsible for approving (certifying) the subject equipment. John Kuivinen Printed name of official Signature of official 5817 Dryden Place, Suite D October 5, 2012 Address Date 760-438-7138 [email protected] Telephone number Email address of official NOTE—This affirmation must be signed by the responsible party before it is submitted to a regulatory body for approval. Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: QNP915SRN Report Number: 2012 10221065 EMC IC: 4676A-915SRN Specification: FCC Part 15 Subpart C, 15.249 Page 3 of 26 Section1: Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC Part 15; Subpart C and IC RSS-210. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made in a 10m semi-anechoic chamber. A description of the test facility is on file with the FCC and IC. The assessment summary is as follows: Apparatus Assessed: Alarm Siren Model: SW-ATT-SRN Specification: FCC Part 15 Subpart C, 15.249 IC RSS-210 Issue 8 December 2010 Date Received in Laboratory: September 24, 2011 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: QNP915SRN Report Number: 2012 10221065 EMC IC: 4676A-915SRN Specification: FCC Part 15 Subpart C, 15.249 Page 4 of 26 1.1 Report Release History REVISION DATE COMMENTS - October 5, 2012 Prepared By: Mark Phillips - October 5, 2012 Initial Release: Alan Laudani Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. TESTED BY: Date: October 5, 2012 Mark Phillips, EMC Test Engineer Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: QNP915SRN Report Number: 2012 10221065 EMC IC: 44676A-915SRN Specification: FCC Part 15 Subpart C, 15.249 Page 5 of 26 TABLE OF CONTENTS 1 Applicant Affirmation ............................................................................................. 2 Section1: Summary of Test Results ................................................................................ 3 1.1 Report Release History ..................................................................................... 4 Section 2: Equipment Under Test ................................................................................... 6 2.1 Product Identification ........................................................................................ 6 2.2 Samples Submitted for Assessment ................................................................. 6 2.3 Theory of Operation .......................................................................................... 7 2.4 Technical Specifications of the EUT ................................................................. 7 Section 3: Test Conditions .............................................................................................. 8 3.1 Specifications .................................................................................................... 8 3.2 Deviations From Laboratory Test Procedures ................................................... 8 3.3 Test Environment .............................................................................................. 8 3.4 Test Equipment ................................................................................................. 9 Section 4: Observations ................................................................................................ 10 4.1 Modifications Performed During Assessment .........................…

Text truncated - open the document above for the full version.