QNP-PAN319Panic FOB

SW-NAP-PAN Single Button Panic NAPCO CAMPATIBLE INSTALLATION MANUAL TECHNICAL SUPPORT Secure Wireless 866-908-Tech www.mysecurewireless.com KEYFOB ENROLLMENT PROGRAMMING For a detail programming guide, the instruction manual should be consulted for that panel. The below guide should only be used as a reference and not as a replacement for using the programming instructions. 1.ENTER Panel Programming 2.SELECT Zone # 3.ENTER 6 Digit Id Number ( located on back of unit) 4.ENTER Check sum (0-9 ; A-F) (located on back on unit. Digit that follows “:” on the Serial ID 5.ENTER Point “3” – for Panic 6.Push On/Off to Save Note : Panic trouble must reset at keypad after disarm Alpha Chart A - *0 C - *2 E - *4 B - *1 D- * 3 F - * 5 REPLACING THE BATTERY Open the case using a flathead screwdriver. (+) should be facing up. . Re-assembly by pressing the board into place firmly and re-attach with the screw. Snap case back together. FCC Compliance This device complies with Part 15 FCC Rules. Operation complies with the following 2 conditions (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation MODEL SW-NAP-PAN FCC ID QNP-PAN319 FREQUENCY 319.5 MHz WARRARTY Limited Life Time BATTERY CR2032 Replace with Panasonic MANUAL PART # 200-10002 Rev A USING PANIC ACCESSORIES The SW-NAP-PAN is equipped with an accessory pack to allow for a variety of uses for the SW-NAP-PAN. For WRIST-STRAP or NECK-STRAP: 1.Open the case with a flathead screw driver NECK-STRAP WRIST-STRAP 2.Choose NECK-STRAP or WRIST-STRAP case 3.Attach the new bottom case by pressing together firmly The other accessories can be used with the standard case bottom that is on the remote when taken out of the box.

LABEL,FCC ID,EV-PA319N 187-0903 A ARTWORK DRAW ING Mo del # SW-NA P-PA N FCC ID: QNP-PAN319 IC: 4676A-PAN319 Mad e in China Secure Wire less Inc . .750” .500 ” Mo del # SW-NA P-PA N FCC ID: QNP-PAN319 IC: 4676A-PAN319 Mad e in China Secure Wire less Inc . Mo del # SW-NAP-PA N IC: 4676A-PAN319 Mad e in China Secure Wire less Inc . FCC ID: QNP-PAN319

Secure Wireless Inc. Model # SW-NAP-PAN FCC ID: QNP-PAN319 IC: 4676A-PAN319 Made in China

Antenna Specification SW-NAP-PAN Rev 1 The SW-NAP-PAN transmitter uses and internal -15 dBi printed PCB loop antenna which is not replaceable by the user.

Underwriters Laboratories Inc. A not-for-profit organization dedicated 1285 Walt Whitman Rd. to public safety and committed to Melville, NY 11747 quality service for over 100 years Tel: (631) 271-6200 Fax: (631)439-6095 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, NY 11747 www.ul.com/emc (631) 271-6200 Job Number: 11U16340 Project Number: SR7342952-T001 Date: 2011-02-17 Revision Date: 2011-04-18 Model: SW-NAP-PAN FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Electromagnetic Compatibility Test Report For Secure Wireless, Inc Copyright  2010 Underwriters Laboratories Inc. Underwriters Laboratories Inc. authorizes the above-named company to reproduce this Report provided it is reproduced in its entirety. Job Number: 11U16340 Page 2 of 30 Model Number: SW-NAP-PAN Client Name: Secure Wireless, Inc FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, New York 11747 USA Tel.: 631 271-6200 Fax: 631 439-6095 Rev. No 1.0 EMC Report 2010-87-EM-F0042 Test Report Details Tests Performed By: Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, NY 11747 Tests Performed For: Secure Wireless, Inc 5817 Dryden Place, Suite D Carlsbad, CA 92008 Applicant Contact: Jay Stone Phone: (866) 966-9473 E-mail: [email protected] Test Report Date: 2011-02-17 Test Report Revision Date: 2011-04-18 Product Type: Panic FOB Product standards FCC Part 15, Subpart C, 15.231, RSS-GEN, Issue 3, RSS-210, Issue 8 Model Number: SW-NAP-PAN Sample Serial Number: Non-serialized production unit EUT Category: Periodic Low Power Transmitter Testing Start Date: 2011-02-05 Date Testing Complete: 2011-02-15 Overall Results: Compliant Underwriters Laboratories Inc. reports apply only to the specific samples tested under stated test conditions. All samples tested were in good operating condition throughout the entire test program. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. Underwriters Laboratories Inc. shall have no liability for any deductions, inferences or generalizations drawn by the client or others from Underwriters Laboratories Inc. issued reports. This report shall not be used to claim, constitute or imply product certification, approval, or endorsement by NVLAP, NIST, A2LA, or any agency of the US government. This report may contain test results that are not covered by the NVLAP or A2LA accreditation. The scope of accreditation is limited to the specific tests that are listed on the NVLAP and/or A2LA websites referenced at the end of this report. Job Number: 11U16340 Page 3 of 30 Model Number: SW-NAP-PAN Client Name: Secure Wireless, Inc FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, New York 11747 USA Tel.: 631 271-6200 Fax: 631 439-6095 Rev. No 1.0 EMC Report 2010-87-EM-F0042 Report Directory 1.0 G E N E R A L - Product Description ..................................................................................................................4 1.1 Equipment Description ...................................................................................................................................4 1.2 Equipment Marking Plate ...............................................................................................................................4 1.3 Device Configuration During Test ..................................................................................................................5 1.3.1 Equipment Used During Test: ....................................................................................................................5 1.3.2 Input/Output Ports: .....................................................................................................................................5 1.3.3 EUT Internal Operating Frequencies: ........................................................................................................6 1.3.4 Power Interface: .........................................................................................................................................6 1.4 Block Diagram: ...............................................................................................................................................6 1.5 EUT Configurations ........................................................................................................................................7 1.6 EUT Operation Modes ....................................................................................................................................7 2.0 Summary ............................................................................................................................................................8 2.1 Deviations from standard test methods ..........................................................................................................8 2.2 Device Modifications Necessary for Compliance ...........................................................................................8 2.3 Reference Standards .....................................................................................................................................9 2.4 Results Summary ...........................................................................................................................................9 3.0 Calibration of Equipment Used for Measurement ........................................................................................... 10 4.0 EMISSIONS TEST RESULTS ......................................................................................................................... 10 4.1 Test Conditions and Results – Occupied Bandwidth .................................................................................. 11 4.2 Test Conditions and Results – Cease Operation ..............................…

Text truncated - open the document above for the full version.

Job Number: 11U16340 Page 12 of 30 Model Number: SW-NAP-PAN Client Name: Secure Wireless, Inc FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, New York 11747 USA Tel.: 631 271-6200 Fax: 631 439-6095 Rev. No 1.0 EMC Report 2010-87-EM-F0042 Figure 1 Test Setup for Occupied Bandwidth Job Number: 11U16340 Page 15 of 30 Model Number: SW-NAP-PAN Client Name: Secure Wireless, Inc FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, New York 11747 USA Tel.: 631 271-6200 Fax: 631 439-6095 Rev. No 1.0 EMC Report 2010-87-EM-F0042 Figure 3 Test Setup for Cease Operation Job Number: 11U16340 Page 18 of 30 Model Number: SW-NAP-PAN Client Name: Secure Wireless, Inc FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, New York 11747 USA Tel.: 631 271-6200 Fax: 631 439-6095 Rev. No 1.0 EMC Report 2010-87-EM-F0042 Figure 5 Test Setup for Pulse Train Job Number: 11U16340 Page 25 of 30 Model Number: SW-NAP-PAN Client Name: Secure Wireless, Inc FCC ID: QNP-PAN319 IC Number: 4676A-PAN319 Underwriters Laboratories Inc. 1285 Walt Whitman Rd. Melville, New York 11747 USA Tel.: 631 271-6200 Fax: 631 439-6095 Rev. No 1.0 EMC Report 2010-87-EM-F0042 Figure 7 Test setup for Radiated Emissions