QNPEV-F433W4 Buttons Recessed Door/Window Sensor operates in

Rev. A ZoneControl EV-F433W, Wireless Wallfob Congratulations, you have purchased a ZoneControl compatible, model EV-F433W wallfob. The EV-F433W is designed as an upgraded remote which can be easily mounted inside your home for easy control of your landscape lighting. Included in the Box Installation is as easy as learning the remote to your Zonecontrol and mounting it in a convenentely located spot in your house. WallFob Installation STEP 1 STEP 2 Included in the Box Remove the product from the box and stand within close proximity to the Zonecontrol. 10 ft. or less is recommended. WallFob Installation Using the small magnet supplied with the ZoneControl Swipe Reed #1 (see diagram) 1 3 1 STEP 3 STEP 4 STEP 5 Receiver should beep slowly. Press any button on the ZoneCTRL-WallTX until you hear a loud beep. Unit is now programmed for manual activation of your ZoneControl system. Determine the desired convenient location to mount the WallFob. STEP 6 to mount the WallFob. Utilize the included 3M doublesided to mount the Wallfob in the desired location. ZoneCTRL-WallTX has tactile feedback. When any button on the Wallfob is pressed a "click" can be felt. Picture of Zonecontrol Unit with Reed callouts Misc. Notes 4 FCC Compliance Statement: Long-life Lithium Batteries are included in the Wallfob. The CR2025 long-life batteries should last 7-10 years under normal conditions. The LED will blink rapidly when a button is pressed if running low. Simply remove the cover and replace the battery. ZoneCTRL-WallTX has tactile feedback. When any button on the Wallfob is pressed a "click" can be felt. The tactile feedback coupled with the visual LED gives absolute confirmation that the signal was sent. Any changes or modifications not expressly approved by the party responsible for Limited Manufacturers Warranty Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following ABT (Advanced Bridging Technologies) offers a limited 1 year warranty from date of purchase that this product is free from defects in material, workmanship, and conforms to its specifications. This warranty does not apply to damage caused by: (a) accident, abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or products not manufactured by or for ABT. If there is a defect in materials, workmanship, or a problem with the product during the warranty period, ABT will at its sole discretion replace the product. user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC Rules. Oper ation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The maximum liability for ABT under all circumstances for any warranty issue shall be limited to a replacement of the defective product. It is recommended that the customer check their equipment on a regular basis for proper functionality. Please contact ABT at 888-869-4737 for all communications regarding this warranty. 1

Antenna Specification EV-F433W, 433.92 MHz Wall Tx Rev 1 The EV-F433W transmitter uses and internal -12 dBi printed PCB antenna which not replaceable by the user.

FCC CFR47 PART 15 SUBPART C IC RSS-210 CERTIFICATION TEST REPORT FOR 4 BUTTONS RECESSED DOOR/WINDOW SENSOR OPERATES IN 433.92MHZ MODEL NUMBER: EV-F433W FCC ID: QNPEV-F433W IC: 4676A-EVF433W REPORT NUMBER: 08U11610-1 ISSUE DATE: FEBRUARY 11, 2008 Prepared for SECURE WIRELESS, INC. 5817 DRYDEN PLACE, SUITE D CARLSBAD, CA 92008 Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 08U11610-1 DATE: FEBRUARY 11, 2008 FCC ID: QNPEV-F433W IC: 4676A-EVF433W Page 2 of 21 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 02/11/08 Initial Issue T. Chan REPORT NO: 08U11610-1 DATE: FEBRUARY 11, 2008 FCC ID: QNPEV-F433W IC: 4676A-EVF433W Page 3 of 21 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 4 2. TEST METHODOLOGY ........................................................................................................ 5 3. FACILITIES AND ACCREDITATION.................................................................................... 5 4. CALIBRATION AND UNCERTAINTY .................................................................................. 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST ................................................................................................. 6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. SOFTWARE AND FIRMWARE .................................................................................................... 6 5.3. WORST-CASE CONFIGURATION AND MODE......................................................................... 6 5.4. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................................. 6 5.5. DESCRIPTION OF TEST SETUP ................................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................... 9 7. LIMITS AND RESULTS ...................................................................................................... 10 7.1. 20dB & 99% BANDWIDTHS...................................................................................................... 10 7.2. MAXIMUM MODULATION PERCENTAGE (M%) .................................................................. 12 7.3. LESS THAN 5 SECONDS PLOT ................................................................................................ 14 7.4. RADIATED EMISSIONS.............................................................................................................15 7.4.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ...................................................... 15 7.4.2. RECEIVER SPURIOUS EMISSIONS LIMIT...................................................................... 19 8. SETUP PHOTOS................................................................................................................. 20 REPORT NO: 08U11610-1 DATE: FEBRUARY 11, 2008 FCC ID: QNPEV-F433W IC: 4676A-EVF433W Page 4 of 21 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: GE SECURITY 1275 RED FOX ROAD ARDEN HILLS, MN 55112, U.S.A. EUT DESCRIPTION: 4 BUTTONS RECESSED DOOR/WINDOW SENSOR PERATES IN 433.92MHZ MODEL: EV-F433W SERIAL NUMBER: 62851F DATE TESTED: FEBRUARY 06, 2008 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED RSS-210 Issue 7 NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency. Approved & Released For CCS By: Tested By: THU CHAN DEVIN CHANG EMC SUPERVISOR EMC ENGINEER COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES REPORT NO: 08U11610-1 DATE: FEBRUARY 11, 2008 FCC ID: QNPEV-F433W IC: 4676A-EVF433W Page 5 of 21 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4-2003, FCC CFR 47 Part 2 and FCC CFR 47 Part 15, I…

Text truncated - open the document above for the full version.

REPORT NO: 08U11610-1 DATE: FEBRUARY 11, 2008 FCC ID: QNPEV-F433W IC: 4676A-EVF433W Page 20 of 21 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 8. SETUP PHOTOS RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION X-AXIS PHOTO REPORT NO: 08U11610-1 DATE: FEBRUARY 11, 2008 FCC ID: QNPEV-F433W IC: 4676A-EVF433W Page 21 of 21 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION END OF REPORT YAXIS PHOTO