R33LDZ1011LDZ-101-X Controllable Dimmer

Control4 Wireless Dimmer Installation and User Guide 1 Wireless Dimmer Installation and User Guide Supported Models and Fixtures This installation and user guide covers these dimmer models: This dimmer can operate independently or as a device you can control with your Control4 system. The dimmer installs in a standard wall box using typical wiring standards and it communicates to the Control4 system using a wireless connection. The dimmer supports: •120 Volt incandescent (all types) •120 Volt halogen (all types) •120 Volt magnetic low voltage (all types with 70 percent or greater load factor) •120 Volt electronic low voltage (dimmable only) •120 Volt fluorescent light fixtures (dimmable only) Installation Instructions Ensure that the location and intended use meet the following criteria: To avoid injury or death, turn OFF local electrical power. To turn off the power, either switch off the circuit breaker or remove the fuse from fuse box. To ensure the wires do NOT have power running to them, use an inductive voltage detector. Use screwdriver to remove wall plate and existing switch from wall. Detach existing dimmer or switch. The existing dimmer or switch is wired in one of three ways: terminal screws, backwire, or wire nuts. LDZ-101-WWireless Dimmer (802.15.4) LDZ-101-BWireless Dimmer (802.15.4) LDZ-101-AWireless Dimmer (802.15.4) WARNING! To reduce the risk of serious injury or death, turn all power OFF before installing this product. Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Limited 1 Year Warranty” on page 6. This product generates heat. The room must have adequate ventilation or heat dissipation ability. Do NOT use this device to control a device with a non- dimmable load. You should only use it with devices that have dimmable feature support. DO (OK, Normal)DON’T •Install in accordance with all national and local electrical codes. •Wall box size required depends on your wiring. The dimmer alone needs a depth of 2.5 inches. To calculate the total depth required, add 2.5 inches to the amount of space recommended in the NEC (National Electric Code) for your configuration. •The range and performance of the control system is highly dependent on the following: • Distance between devices • Layout of the home • Walls separating devices • Electrical equipment located near devices •If installing a multi-unit dim- mer, Do NOT continue until you have read “Multi-Unit Installations” on page 2. •Do NOT use where total watt- age is under 25 watts. •Do NOT exceed maximum load rating of dimmer (which is 1000W for a single unit, if both side tabs are in tact). WARNING! As with any appliances, improper use or installation can cause SERIOUS INJURY or DEATH. Do NOT attempt the installation if you are NOT sure which wires are the hot and load wires in the wall box. Instead, have a trained electrician do the installation. Terminal Screws: Use a screwdriver to unscrew the screws to release the wire. Backwire: Insert screwdriver in Wire Release slot and pull out wire. If this does not work, use a wire cutter to cut the wire. Wire Nuts: Turn to remove wire nuts from existing wiring. 1 2 3 4 OR OR Control4 Wireless Dimmer Installation and User Guide 2 Prepare and identify all wires. Identify the wires in your wall box. Straighten the wire ends. With a wire cutter, cut off the bare wire just below the plastic insulation on all wires. Use a wire stripper to strip off about 3/8-inch of the insulation. Connect the dimmer wires to the wall box wires using wire nuts. Wall box wires can differ depending upon how the box was wired by your electrician and where the power source comes from—the light fixture or the wall box. Refer to the following four sections (beginning on page 3): • “Single-Switch Environment—Power Source at Wall Box” • “Single-Switch Environment—Power Source at Light Fixture” • “3-Way-Switch Environment—Power Source at Wall Box” • “3-Way-Switch Environment—Power Source at Light Fixture” Fit wires back into the wall box. Bend the wires in a zigzag pattern so that they easily fold into the wall box. Push the dimmer into place. Adjust the dimmer so that it is perpendicular to the floor. Tighten the two screws that hold it in position in the wall box. Align dimmer to wall box and fasten with screws, unless you are using a Decora screw- on-style wall plate. If you are using a screw-on-style wall plate, before fastening with screws, you must first align the wall plate with the dimmer and the wall box. If you are using the Control4 snap-on- style wall plate, snap it over the dimmer now. Turn ON power at the circuit breaker or replace fuse from fuse box. Test the dimmer to see if it is working properly. For details, see “Operation and Configuration” on page 5. Troubleshooting If light does not turn on: •Ensure light bulb is not burned out. •Ensure light bulb is screwed in tightly. •Ensure circuit breaker is not turned OFF or tripped. •Check for proper wiring (see the subsections beginning on page 3). Multi-Unit Installations Multi-unit installations allow you to install one stand-alone dimmer next to another in the same wall box. Remove Inner Sides When using multiple units in a wall box, you must remove the inner sides, leaving the outer sides in place. Use pliers to bend a tab back and forth until it comes off. Remove only the sides that will touch another dimmer. Do not remove sides that will become outer sides. Resulting Capacity •With both sides intact (single unit), the capacity is 1000W maximum. •If you remove one side, the capacity is reduced to 800W maximum. •If you remove two sides, the capacity is reduced to 600W maximum. IMPORTANT: The National Electric Code (NEC) requires 6 inches of extended wire from the wall box. If your wiring does not meet this requirement, you will not meet code. Do NOT cut wire shorter than 6 inches. IMPORTANT: When installing thi…

Text truncated - open the document above for the full version.

Exhibit 13 11734 South Election Drive Suite 200 Draper, Utah 84020 (801) 523-3100 To: Federal Communications Commission Date: 4/29/04 445 12 th Street, SW Washington, DC 20554 Re: Non disclosure Request for FCC ID: R33LDZ1011 We are requesting that the following documents be held and treated as confidential and proprietary information. These materials contain technical trade secret information and should be guarded from competitors as stated under the Code of Federal Regulations Title 47 Section 0.459 (3), (4) and (5). 1) Schematic 2) Block Diagrams 3) Operational Description James K. Russell Senior Electrical Engineer Control4 Technologies

Page 1 of 2 Exhibit 3 (External Photographs) Photograph 1 – Front View of the EUT Page 2 of 2 Photograph 2 – Back View of the EUT

1 MPE Calculations R33LDZ1011 2 1.0 SCOPE_________________________________________________________3 2.0 REVISION LEVEL_______________________________________________4 3.0 REFERENCE DOCUMENTS______________________________________4 4.0 CALCULATIONS________________________________________________5 5.0 CONCLUSION___________________________________________________6 3 1.0 SCOPE: This Report Demonstrates Evaluation and Compliance for Human Exposure to Radiofrequency Electromagnetic Fields as Outlined by the Federal Communications Commission Office of Engineering and Technology Bulletin 65. 2.0 REVISION LEVEL: DATE COMMENTS REVISION 10/13/2004 Created. 1.0 9/29/04 Updated FCC ID number 2.0 3.0 REFERANCE DOCUMENTS: (A) Limits for Maximum Permissible Exposure (MPE). Code of Federal Regulations Title 47, Volume 1, Section 1.1310. (B) Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields. OET Bulletin 67 Edition 97-01. 4.0 CALCULATIONS: The following worst case emissions are based on a PPt (Peak Power Total) measurement of 10.4 dBm. And the worst case antenna gain on axis is found to be 3.64 dBi. Total radiated power at the Transmitter: A) Pt = 10.4 dBm + 3.64 dBi = 14.4 EIRP 14.04 EIRP = 25.35 mW or .02535 Watts. Power density at a distance of .02 meters is: B) S = EIRP/4π·R^2 S = Power density (mW/cm^2) EIRP = Equivalent isotropically radiated power (mW) R = Distance to the center of radiation of the antenna (cm) 4 S = 100.869 mW per meter squared. Power density based on a Per Centimeter Squared is: 10.08 μW per centimeter squared. 5.0 CONCLUSION: Based on the FCC Limits for Maximum Permissible Exposure (MPE) given in Table 1 of reference document (A) this device falls under the required limits.

Exhibit 6 TEST REPORT FROM: COMMUNICATION CERTIFICATION LABORATORY TEST OF: LDZ-101-x FCC ID: R33LDZ1011 To FCC PART 15, Subpart B ICES-003 Test Report Serial No: 73-7955 TEST REPORT FROM: COMMUNICATION CERTIFICATION LABORATORY 1940 W. Alexander Street Salt Lake City, Utah 84119-2039 Type of Report: Certification TEST OF: LDZ-101-x FCC ID: R33LDZ1011 To FCC PART 15, Subpart C (15.203, 15.207, 15.247) Test Report Serial No: 73-7955 Applicant: Control4 11734 S. Election Drive, Suite 200 Draper, UT 84020 Date of Test: April 26, 2004 Issue Date: May 4, 2004 Equipment Receipt Date: April 25, 2004 COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-7955 FCC ID#: R33-LDZ-101-X Page 2 of 51 CERTIFICATION OF ENGINEERING REPORT This report has been prepared by Communication Certification Laboratory to document compliance of the device described below with the requirements of Federal Communications Commission (FCC) Part 15, Subpart C, Sections 15.203, 15.207, and 15.247. This report may be reproduced in full, partial reproduction may only be made with the written consent of the laboratory. The results in this report apply only to the sample tested. - Applicant: Control4 - Manufacturer: Control4 - Brand Name: Control4 - Model Number: LDZ-101-x - FCC ID Number: R33LDZ1011 On this 4 th day of May 2004, I, individually, and for Communication Certification Laboratory, certify that the statements made in this engineering report are true, complete, and correct to the best of my knowledge, and are made in good faith. Although NVLAP has recognized that the Communication Certification Laboratory EMC testing facilities are in good standing, this report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. COMMUNICATION CERTIFICATION LABORATORY Tested by: Norman P. Hansen EMC Technician COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-7955 FCC ID#: R33-LDZ-101-X Page 3 of 51 TABLE OF CONTENTS PAGE SECTION 1.0 CLIENT INFORMATION .................................4 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) ..........................5 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES ...........8 SECTION 4.0 OPERATION OF EUT DURING TESTING ...................14 SECTION 5.0 SUMMARY OF TEST RESULTS ...........................16 SECTION 6.0 MEASUREMENTS, EXAMINATIONS AND DERIVED RESULTS .....17 APPENDIX 1 TEST PROCEDURES AND TEST EQUIPMENT ..................33 APPENDIX 2 PHOTOGRAPHS .........................................42 COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-7955 FCC ID#: R33-LDZ-101-X Page 4 of 51 SECTION 1.0 CLIENT INFORMATION 1.1 Applicant: Company Name: Control4 11734 S. Election Drive, Suite 200 Draper, UT 84020 Contact Name: James Russell Title: Senior Design Engineer 1.2 Manufacturer: Company Name: Control4 11734 S. Election Drive, Suite 200 Draper, UT 84020 Contact Name: James Russell Title: Senior Design Engineer COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-7955 FCC ID#: R33-LDZ-101-X Page 5 of 51 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) 2.1 Identification of EUT: Brand Name: Control4 Model Name or Number: LDZ-101-x Serial Number: None Options Fitted: N/A Country of Manufacture: U.S.A. 2.2 Description of EUT: The LDZ-101-x is a solid state wireless network able wall box decora™ style dimmer. It has been designed to handle a maximum of 1000 watts. The LDZ-101-x replaces standard mechanical On/Off switches using conventional electrical residential wiring. It fits into all standard plastic or metal electrical wall box sizes. The LDZ-101-x has a fully programmable dimming curve, ramp rate, maximum on and fade control . The LDZ-101-x is network able via a standard 2.4 GHz 802.15.4 low power RF transceiver enabling a full range of system control functions including Lighting Scene Control, Security Lighting, Automatic Shut Off, Scheduled Events and more. The 802.15.4 transceiver uses 15 channels in the 2400 to 2483.5 MHz band. The individual channels are shown in the following plots. dBm 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Control4 Zigbee radio frequencies Trace A Start: 2.402500 GHzStop: 2.427500 GHz Res BW: 100 kHzVid BW: 300 kHzSweep: 20 ms 04/26/2004 2:48:40 PMHP8566BLCHANS.SPT Lower channels 1 1 2.405375 GHz 5.8000 dBm 2 2 2.409825 GHz 5.2000 dBm 3 3 2.414875 GHz 5.3000 dBm 4 4 2.420525 GHz 4.6000 dBm 5 5 2.425650 GHz 4.6000 dBm COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-7955 FCC ID#: R33-LDZ-101-X Page 6 of 51 dBm 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Contorl4 Zigbee radio frequencies Trace A Start: 2.427500 GHzStop: 2.452500 GHz Res BW: 100 kHzVid BW: 300 kHzSweep: 20 ms 04/26/2004 2:54:11 PMHP8566B Middle channels 1 1 2.429800 GHz 4.7000 dBm 2 2 2.434900 GHz 4.2000 dBm 3 3 2.440000 GHz 5.2000 dBm 4 4 2.445050 GHz 3.8000 dBm 5 5 2.450175 GHz 5.2000 dBm dBm 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Control4 Zigbee radio frequencies Trace A Start: 2.452500 GHzStop: 2.477500 GHz Res BW: 100 kHzVid BW: 300 kHzSweep: 20 ms 04/26/2004 2:59:12 PMHP8566B Upper channels 1 1 2.454850 GHz 3.9000 dBm 2 2 2.460175 GHz 3.4000 dBm 3 3 2.465100 GHz 3.7000 dBm 4 4 2.470750 GHz 3.7000 dBm 5 5 2.475800 GHz 3.1000 dBm COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-7955 FCC ID#: R33-LDZ-101-X Page 7 of 51 2.3 EUT and Support Equipment: The FCC ID numbers for all the EUT and support equipment used during the test (including inserted cards) are listed below: Brand Name Model Number Serial No. FCC ID Number Description Name of Interface Ports / Interface Cables BN: Control4 MN: LDZ-101-x (1) R33LDZ1011 Wireless Solid State Dimmer See Section 2.4 Note: (1) EUT. The support equipment listed above was not modified in order to achieve compliance with this standard. 2.4 Interface Ports on EUT: Name of Ports No. of Ports Fitted to EUT Cable Descriptions/Length AC power 1 3 conductor power cord/6 feet Load 1 Single conductor/3 ½ feet 2.5 Modification Incorporated/Special Accessories on EUT: There w…

Text truncated - open the document above for the full version.

Page 1 of 4 Exhibit 7 (Setup Photographs) Photograph 1 – Front View Radiated Disturbance Worst Case Configuration Page 2 of 4 Photograph 2 – Back View Radiated Disturbance Worst Case Configuration Page 3 of 4 Photograph 3 – Front View Conducted Disturbance Worst Case Configuration Page 4 of 4 Photograph 4 – Back View Conducted Disturbance Worst Case Configuration