RXZ-WA25TD2ADSL 2 PLUS ROUTER WIRELESS

802.11g Wireless Four Port Ethernet ADSL2+ Router User’s Manual November 2007 1 FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which - Consult the dealer or an experienced radio/TV technician for help. the receiver is connected. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of about eight inches (20cm) between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Notice Changes or modifications to the equipment, which are not approved by the party responsible for compliance could affect the user's authority to operate the equipment. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. 2 Copyright 2007 All Rights Reserved. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies. Revision History Revision History V1.1 1 st release 3 Table of Contents 1. Introduction ........................................................................6 1.1 Introduction .................................................................................................. 6 1.2 Product Features ......................................................................................... 6 2. Hardware Installation........................................................10 2.1 System Requirements ............................................................................... 10 2.2 Package Contents ...................................................................................... 10 2.3 Front Panel Indicators and Description ................................................... 10 2.4 Back Panel.................................................................................................. 11 2.5 Connect Related Devices .......................................................................... 11 3. Connecting Wireless ADSL2+ Router via Ethernet .............12 3.1 Setup Wireless ADSL2+ router via Ethernet Cable ................................. 12 3.2 Configure TCP/IP........................................................................................ 12 4. Configure Wireless ADSL2+ Router via HTML ....................26 4.1 Login ........................................................................................................... 26 4.2 Navigating the Web Configurator ............................................................. 27 5. Quick Start Wizard.............................................................28 5.1 Setting a New Password............................................................................ 30 5.2 Choose your Time Zone ............................................................................ 30 5.3 Set your Internet Connection .................................................................... 31 5.3.1 Configuring Dynamic IP Address................................................... 31 5.3.2 Configuring Static IP Address ........................................................ 32 5.3.3 Configuring PPPoE ......................................................................... 33 5.3.4 Configuring PPPoA ......................................................................... 33 5.3.5 Configuring Bridge Mode ............................................................... 34 5.3.6 Multiplexing ..................................................................................... 35 5.3.7 VPI and VCI ...................................................................................... 35 5.4 Finishing the Wizard .................................................................................. 36 6. Interface Setup .................................................................37 6.1 Internet ........................................................................................................ 37 6.1.1 ATM VC & QoS.................................................................................... 38 6.1.2 Encapsulation..................................................................................... 39 6.2 LAN .............................................................................................................. 43 6.2.1 Router Local IP....................................…

Text truncated - open the document above for the full version.

47 6.3 Wireless 6.3.1 Access Point Settings Beacon Interval: The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake. Set this attribute to be larger than the maximum MSDU (MAC Service Data Unit) size TURNS OFF the RTS/CTS handshake. Set this attribute to ZERO TURNS ON the RTS/CTS 48 handshake. Enter a value between 0 and 2432. Fragment Threshold: The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Enter a value between 256 and 2432. DTIM: This value is between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). 6.3.2 Multiple SSIDs Settings SSID: The SSID is a unique name to identify the ADSL Router in the Wireless LAN. Wireless Clients associating to the ADSL Router must have the same SSID. The define SSID name is Default_WLAN. Broadcast SSID: Select No to hide the SSID such that a station can not obtain the SSID through passive scanning. Select Yes to make the SSID visible so a station can obtain in the SSID through Passive scanning. Channel ID: The range of radio frequencies used by IEEE 802.11b/g wireless devices us called a channel. [Authentication Type] WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. Select Disable to allow all wireless computers to communicate with the access points without any data encryption. Select 64-bit WEP or 128-bit WEP to use data encryption. Key#1~Key#4 The WEP keys are used to encrypt data. Both the ADSL Router and the wireless clients must use the same WEP key for data transmission. If you chose 64-bit WEP, then enter any 10 hexadecimal digits (“0-9”, “A-F”) preceded by 0x for each key (1-4). If you choose 1280bit WEP, then enter 26 hexadecimal digits (“0-9”, “A-F”) preceded by 0x for each key (1-4). The values must be set up exactly the same on the Access Points as they are on the wireless client stations. The same value must be assigned to Key 1 on both access point (your ADSL Router) and the client adapters, the same value must be assigned to Key 2 on both access point and the client stations and so on, for all four WEP keys. WPA-PSK Wi-Fi Protected Access, pre-shared key. Encrypts data frames before transmitting over the wireless network. Pre-shared Key is used to encrypt data. Both the ADSL Router and the wireless clients must use the same WPA-PSK Key for data transmission. 6.3.3 MAC Address Filter You can allow or deny a lust of MAC addresses associated with the wireless stations access to the ADSL Router. Status: Use the drop down list box to enable or disable MAC address filtering. 49 Action: Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router. Select Allow Association to permit access to the router, MAC addresses not lusted will be denied access to the router. 7 Advanced Setup 7.1 Firewall User can enable or disable firewall feature of the ADSL router in the page. Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacts, such as Ping of Death, SYN Flood, Port Scan and Land Attack. SPI: Select this option to Enabled or Disabled the SPI feature. (NOTE: If you enable SPI, all traffics initiate from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side) 7.2 Routing This table lists IP address of Internet destinations commonly accessed by your network. When a computer requests to send data to a listed destination, the device uses the Gateway IP to identify the first Internet router it should contact to route the data most efficiently. Select this option will list the routing table information. You can press ADD ROUTE to edit the static route. (As below screen) 50 [Static Route] Select this option to set Static Routing information. Destination IP Address: This parameter specifies the IP network address of the final destination of packets routed by this rule. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. A gateway does the actual forwarding of the packets. Enter the gateway’s IP address in the field or select which PVC you wish to act as a gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. Metric: Metric represents the “cost” of transmission for routing purposes. IP Routing uses hop count as the measurement of cost, with a minimum of 1 for directly connected networks. Enter a number that approximates the cost for this link. The number need not to be precise, but it must between 1 and 15. In practice, 2 or 3 is usually a good number. Announced in RIP: This parameter determines if the ADSL router includes the router to this 51 remote node in its RIP broadcasts. If you choose Yes, the router in this remote node will be propagated to other hosts through RIP broadcasts. If you choose No, this route is kept private and is not included in the RIP broadcasts. When you are done making changes, click on SAVE to save your changes, DELETE to delete the rule with the parameters you set, BACK to return to the previous screen or CANCEL to exit without saving. 7.3 NAT Network Address Translation (NAT) is a method for disguising the private IP addresses you use on your LAN as the public IP address you use on the Internet. You define NAT rules that specify exactly how and when to translate between public and private IP addresses. Simply select this option to setup the NAT f…

Text truncated - open the document above for the full version.

61 8. Access Management 8.1 ACL Go to Access Management Æ ACL to enable remote management. Access Control Listing (ACL) is a management tool that acts as a filter for incoming or outgoing packets, based on application. You may use telnet or Web to remotely manage the ADSL Router. User just needs to enable Telnet or Web and give it an IP address that wants to access the ADSL Router. The default IP 0.0.0.0 allows any client to use this service to remotely manage the ADSL Router. ACL: There has Activated & Deactivated option. The default setting is Deactivated which means all IP can access via router. If you choose Activated, you only can access via router by listed IP addresses. ACL Rule Index: Index number from 1 and up to 16. Active: Once you choose Yes then you can access the IP via router. Application: Each of these labels denotes a service that you may use to remotely manage the Router. Choices are Web, FTP, Telnet, SNMP, Ping, ALL. Interface: Select the access interface. Choices are WAN, LAN and Both. 62 For Example: How to set your ACL? 1. You must choose Activated to enable your ACL function. 2. Select the ACL Rule Index number (up to 16 number) 3. You can set the specific Secure IP address or set 0.0.0.0 for all IPs. 4. Choose the Application which you want to access for this ACL Rule index. 5. Select the Interface you want to access from. 6. After all settings are ready, click SAVE and continue next ACL Rule Index setting. [Note] 1. You must set one ACL index to access your router via LAN interface. If you don’t, your router cannot access other listed IP Address. (Refer to Index 1). 2. Remember! Once you active your ACL function, you only can access via router by listed Secure IP Address. 8.2 Filter The Router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attackers. Go to Access Management Æ Filter to set different IP filter rules of a given protocol (TCP, UDP, or ICMP) and a specific direction (incoming, outgoing, or both) to filter the packets. IP Filter is a more complex filtering tool, based more on IP and custom rules. Each of the indices can hold six rules, and each interface can have four associated indices, allowing 24 rules per interface. If all six rules in an index are Next rules, the data will be sent to the next index for filtering. 63 Filter Type: You can select IP/MAC Filter, Application, and URL Filter type. IP/MAC Filter Set Index: The IP/MAC Filter Set Index from 1 to 12 and each index can set up to 6 IP Filter. Interface: Choices from PVC0 to PVC7 and LAN. Direction: Choices are Both, Incoming and Outgoing. Select which direction of data flow you wish to apply the filters to. Note that Incoming and Outgoing are from the point of view of your router, relative to the interface you select. For WAN, data coming from outside your system is considered Incoming and data leaving your system is Outgoing. For LAN, data leaving your system is considered Incoming and data entering your system is Outgoing. IP/MAC Filter rule Index: The IP/MAC Filter rule Index from 1 to 6. 64 IP/MAC Filter Rule Editing: Select the IP/MAC Filter Rule Index you wish to modify. Active: Toggle this rule index on or off with Yes or No, respectively. Source IP Address: Enter the source IP address you wish to deny access to your system. Subnet Mask: Enter the subnet mask of the source IP address. Port Number: Enter the port number of the source IP address. Note that 0 means all that ports are allowed. Destination IP Address: Enter the destination IP address that you wish to deny access to your system. Subnet Mask: Enter the subnet mask of the destination IP address Port Number: Enter the port number of the destination IP address. Note that 0 means that all ports are allowed Protocol: Select the protocol to filter. Choices are TCP, UDP, and ICMP. Rule Unmatched: Choices are Forward and Next. Select what happens to the data in question if the rule you are currently editing is unmatched. Next means that the data is then compared to the next IP filter rule. Forward means that the data will be allowed into your system. Note that a Forward rule should be the last rule, as no data will be compared to rules after a Forward rule. IP/MAC Filter Set Index: Select the IP/MAC filter set you wish to view. For Example Please follow below steps to set your IP Filter: 1. IP/MAC Filter Set Editing: Choose your IP/MAC Filter Set Index, Interface and Direction options. Remember, Interface and Direction functions are affected with IP/MAC Filter Set Index. EX: if your 1 st index set of IP filter set PVC0 as Interface and Outgoing as Direction, so the list of 1 st IP Filter will be PVC0 and Outgoing as their settings. 2. IP/MAC Filter Rule Editing: Select the IP/MAC Filter Rule Index (up to 6 numbers for each set index) and choose Active option. As below example, Source IP Address is 192.168.1.4, Subnet Mask is 255.255.255.255, Destination IP Address & Subnet Mask is 0.0.0.0, Port Number is 80. And, Protocol sets TCP. From this setting, it filters 192.168.1.14, so it cannot access the web. Notice, each IP Filter Set Index can has up to 6 filters IP. At “Rule Unmatched” option, you must choose NEXT until the last filter IP choose Forward. 3. After every setting is done, click SAVE to continue next IP Filter Editing. 65 66 8.3 SNMP The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. It enables a host computer to access configuration, performance, and other system data that resides in a database on the modem. The host computer is called a management station and the modem is called an SNMP agent. The data that can be accessed via SNMP is stored in a Management Information Database (MIB) on the modem. Get Community: Select to set the password for incoming Get- and GetNext request from management station. Set Community: Select to set the password for incoming Se…

Text truncated - open the document above for the full version.

74 10. Status 10.1 Device Info The Device Info screen is a tool that you use to monitor your ADSL Router. It shows the Firmware Version, WAN, LAN, and MAC address information. Note that these fields are read-only and are not meant for diagnostic purposes. Except the Virtual Circuit, click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. [Device Information] Firmware Version: This filed displays current firmware version. MAC Address: The MAC (Media Access Control) or Ethernet address unique to your modem. 75 [LAN] IP Address: The LAN port IP address Subnet Mask: The LAN port IP subnet mask. DHCP Server: The status of DHCP Server (Enabled or Disabled) [WAN] Virtual Circuit: Click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. Status: Connected or Not Connected Connection Type: The WAN Connection Type. IP Address: The WAN port IP address Subnet Address: The WAN port IP subnet mask. Default Gateway: The IP address of the default gateway, if applicable. DNS Server: The IP address of the DNS Server [ADSL] ADSL Firmware Version: This field displays current ADSL firmware version. Line States: This field displays the ADSL connection process and status. Modulation: This field displays the ADSL modulation status for G.dmt or T1.413. Annex Mode: This field displays the ADSL annex modes for Annex A or Annex B. Downstream and Upstream: Status of SNR Margin, Line Attenuation and Data Rate SNR Margin: Amount of increased noise that can be tolerated while maintaining the designed BER (bit error rate). The SNR Margin is set by Central Office DSLAM. If the SNR Margin is increased, bit error rate performance will improve, but the data rate will decrease. Conversely, if the SNR Margin is decreased, bit error rate performance will decrease, but the data rate will increase. Line Attenuation: Attenuation is the decrease in magnitude of the ADSL line signal between the transmitter (Central Office DSLAM) and the receiver (Client ADSL Modem), measured in dB. It is measured by calculating the difference in dB between the signal power level received at the Client ADSL Router and the reference signal power level transmitted from the Central Office DSLAM. Data Rate: This field displays the ADSL data rate. 76 10.2 System Log The System Log displays data generated or acquired by routine system communication with other devices, such as the results of negotiations with the ISP's computers for DNS and gateway IP addresses. The device keeps a running log of events and activities occurring on the Router. You can click Save Log to display a Windows File Download dialog box that enables opening or saving the contents of the log to your PC. To remove all entries from the list, click Clear Log. New entries will begin accumulating. If the device is rebooted, the logs are automatically cleared. 77 10.3 Statistics The ADSL Router keeps statistic of traffic that passes through it. You are able to view the amount of packets that passes through the Router on both the WAN port & the LAN port. The traffic counter will reset if the device is rebooted. You can select Ethernet/ADSL to view the statistics report of LAN/WAN. [Ethernet] The Ethernet screen gives you information on how much data your router has transmitted and received across the Ethernet connection. Click on REFRESH to update the screen. [ADSL] The ADSL screen gives you information about how much data your router has transmitted or received across the ADSL connection. Click on REFRESH to update the screen. 78 [WLAN] The WLAN screen gives you information about how much data your router has transmitted or received across the ADSL connection. Click on REFRESH to update the screen. 79 11. Troubleshooting If the router is not function properly, first check this session for simple troubleshooting before contacting your Internet service provider (ISP) for support. 11.1 Using LEDs to Diagnose Problems The LEDs are useful aides for finding possible problem causes. 11.1.1 Power LED The PWR LED on the front panel does not light up. STEPS CORRECTIVE ACTION 1 Make sure that the power adaptor is connected to the router and plugged in to an appropriate power source. Use only the supplied power adaptor. 2 Check that the router and the power source are both turned on and the router is receiving sufficient power. 3 Turn the router off and on. 4 If the error persists, you may have a hardware problem. In this case, you should contact your vendor. 11.1.2 LAN LED The LAN LED on the front panel does not light up. STEPS CORRECTIVE ACTION 1 Check the Ethernet cable connections between your router and the computer or hub. 2 Check for faulty Ethernet cables. 3 Make sure your computer’s Ethernet card is working properly. 4 If these steps fail to correct the problem, contact your local distributor for assistance. 11.1.3 ADSL LED The ADSL LED on the front panel does not light up. STEPS CORRECTIVE ACTION 1 Check the telephone wire and connections between the router ADSL port and the wall jack. 2 Make sure that the telephone company has checked your phone line and set it up for ADSL service. 3 Reset your ADSL line to reinitialize your link to the DSLAM. 4 If these steps fail to correct the problem, contact your local distributor for assistance. 80 11.2 Problems with the Web Interface I cannot access the web Interface. STEPS CORRECTIVE ACTION 1 Make sure you are using the correct IP address of the router. Check the IP address of the router. 2 Make sure that there is not a console session running. 3 Check that you have enabled web service access. If you have configured a secured client IP address, your computer’s IP address must match it. Refer to the chapter on remote management for details. 4 For WAN access, you must configure remote management to allow server access from the WAN (or all). 5 Your computer’s and the router’s IP addresses must be on the same subnet for LAN access. 6 If you changed…

Text truncated - open the document above for the full version.

Device Name: ADSL 2 PLUS ROUTER WIRELESS Model No.: WA25TD2 Date: 1311 112007 To whom it may concern: We, the undersigned, hereby authorize ELECTRONICS TESTING CENTER, TAIWAN, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by ELECTRONICS TESTING CENTER, TAIWAN on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certifythat weare not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: comply with the relevant provisions of the certification program; make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; make claims regarding certification only in respect of the scope for which certification has been granted; do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; use certification only to indicate the products are certified as being in conformity with specified standards; endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the reauirements of the Certification - Division; i) keep a record of all complaints made known to the us relating to the product compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant Sincerely Yours, By: Alex Chen Title : Director I R&D Applicant : PRO-NETS Technology Corp. Address : 7F, No.95, Lide St,Chung Ho City 235,Taipei. Taiwan, R.0.C Tel : +886-2-82218385 Fax. +886-2-82217229

FCC ID: RXZ-WA25TD2 Device Name: ADSL 2 PLUS ROUTER WIRELESS Model No.: WA25TD2 Date: 1311 112007 Federal Communications Commission Dear Sir: Pursuant to Section 0.457 and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Descriptions The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely Yours, By: Alex Chen Title : Director I R8D Applicant : PRO-NETS Technology Corp. Address : 7F, No.95, Lide St,Chung Ho City 235,Taipei, Taiwan, R.O.C. Tel : +886-2-82218385 Fax: +886-2-82217229

PRO-NETS Technology Corp., FCC ID: RXZ-WA25TD2, Assessment NO.: AN07T7447, Notice#1 Inbox X from [email protected] to [email protected], cc [email protected], date Dec 20, 2007 5:27 PM subject PRO-NETS Technology Corp., FCC ID: RXZ- WA25TD2, Assessment NO.: AN07T7447, Notice#1 hide details 5:27 PM (2 hours ago) Reply Dear Joe, The application review is complete. The only issue is that the label exhibit shows the label with FCCID RXZ-WA25TC2. The application and other exhibits show RXZ- WA25TD2. Please send a revised Label exhibit. Best regards, Tim Dwyer Technical Reviewer The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Reply Reply to all Forward from Joe Hsieh <[email protected]> to [email protected], cc [email protected], date Dec 20, 2007 7:46 PM subject Re: PRO-NETS Technology Corp., FCC ID: RXZ-WA25TD2, Assessment NO.: AN07T7447, Notice#1 hide details 7:46 PM (18 minutes ago) Reply Dear Tim, Thank you for your fast and kindly reply. And thank you so much to note the error at label. Attached please find the revise ID label format. Any questions please feel free to contact with me. Best regards, Joe - Show quoted text - ID Label_Location.pdf 58K View as HTML Download

FCC ID: RXZ-WA25TD2 Sheet A1 of A7 Sheets ETC Report No. : 07-10-MAS-236-01 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT FCC ID: RXZ-WA25TD2 Sheet A2 of A7 Sheets ETC Report No. : 07-10-MAS-236-01 3. Outside view 1 of Adaptor 1 4. Outside view 2 of Adaptor 1 FCC ID: RXZ-WA25TD2 Sheet A3 of A7 Sheets ETC Report No. : 07-10-MAS-236-01 5. Outside view 3 of Adaptor 1 FCC ID: RXZ-WA25TD2 Sheet A4 of A7 Sheets ETC Report No. : 07-10-MAS-236-01 6. Outside view 1 of Adaptor 2 7. Outside v…

Text truncated - open the document above for the full version.