TW4AT1012.4G Wireless Camera Kit

Please read this manual carefully and thoroughly before any attempt to install and operate this product and retain it for your future reference. User's Manual 2.4GHz Color Wireless Camera Kit MODEL: A101 English R EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. TABLE OF CONTENTS SPECIFICATIONS 14 TROUBLESHOOTING 15 PRODUCT 5~7 Package Contents Feature Locations Adapter & Battery Clip 5 6 7 INSTALLATION & USAGE 8~13 Installation Fix the Camera Camera Channel Setup Receiver Mode Setup 8~10 12 12 13 Locate the Receiver INTRODUCTION 1~4 Notice Restrictions Maintenance Warranty Copyright Approval Information () FCC/CE 1 3 3 4 4 1~2 11~12 INTRODUCTION Thank you for your interest and support in our product and purchasing this wireless camera kit. This product eel confident that you will be pleased with the quality and features of this product. The camera features one CMOS image sensor and a transmitting module to capture the image and transmit them wirelessly. The receiver features a receiving module to receive and output AV signals. works at ISM-2.4GHz frequency band, which could be legally used worldwide without permission. We f Notice Notice:This product may cause interferences with other wireless equipment that operates at 2.4GHz ISM band. Please turn off one of the equipments to eliminate the interference. Product Assurance: . This camera will emit electromagnetic wave, just like other wireless products. But its transmitting power is lesser than other wireless products such as mobile phones. The 2.4GHz wireless camera meets wireless frequency security standards and recommended indexes while working. These standards and indexes are certificated by academic organization and represent the cogitative research of the scientific workers who continuously explore and annotate the involved fields. So we believe that our products are safe for customers 1 All our products meet the requirements ofFCC or CE, and are granted the FCC or CE approval certification. They are authorized to bear FCC or CE mark. Approval Information After testing the product, we confirm that it complies with the provision for class C digital equipment in the 15th part in FCC regulation; and the receiver complies with the limitations for class B digital equipment in Part 15 of FCC regulation. The product generates, applies and emits radio waves. It might cause harmful interferences to wireless communication if not be installed and used following the description of the manual. The product may cause interference in residential area, and the customer should take remedies to eliminate the interference at their own costs. If the product causes any harmful interference to wireless equipment or disturbs the receiving of TV signals (it can be identified by turning on and off the product), you can solve the trouble by following methods: FCC This product complies with standards including ow oltage evice Directive 73/23/EEC;Directive 89/336/EEC and Directive 1999/5/EC. It passed the subject tests by the authority concerned and is authorized to bearmark. LVD EMCR&TTE CE CE 2 This product meets the requirements specified in Part 15 of FCC Regulation. Operation rests with the following two conditions: (1) The equipment should not cause any harmful interference; (2) The equipment must receive and process any interference, including any possible interference caused by operation mistakes. (1) Readjust the product or put it in another place; (2) Extend the distance between the equipment interfered and the product; and (3) Refer to dealers or experienced radio electrician for help. Copyright This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of AEE Technology. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by AEE Technology. AEE Technology assumes no responsibility or liability for any errors or inaccuracies that may appear in this booklet. All other product names, trademarks and registered trademarks in this document are the properties of their respective holders. Warranty AEE Technology warrants that this product will be free from defects in materials and workmanship for period of time specified. This limited warranty shall commence from the date of purchase. product warranty is not transferable and is limited to the original purchaser. If the product is found to be defective then, as your sole remedy and as the manufacturer's only obligation, will repair or replace the product. This warranty shall not apply to products that have been subjected to abuse, misuse, abnormal electrical or environmental conditions, normal wear and tear or any condition other than what can be considered normal use. Should you have problems, please consult the local dealer. AEE Technology's AEE Technology 3 DO NOT use this product to violate one's privacy. Monitoring one's activities without consent is illegal and this product is not designed and manufactured for such purpose; DO NOT put this product near any medical equipment. Radio waves might potentially cause breakdown of electrical medical equipment. So this product should be placed at least 1 feet away from any heart pacemaker. Radio waves might potentially influence heart pacemaker and lead to respiratory disturbance; DO NOT use this product for any illegal activities. AEE Technology shall not be responsible for any consequences of illegal acts committed by the user. 1. 2. 3. Restrictions Ensure the su…

Text truncated - open the document above for the full version.

Applicant: Shenzhen AEE Technology Co., Ltd. FCC ID: TW4AT101 EUT top view EUT bottom view

Applicant: Shenzhen AEE Technology Co., Ltd. FCC ID: TW4AT101 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Label must not be a stick-on paper label. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Bottom View/Proposed FCC ID Label Location FCC ID: TW4AT101

Applicant: Shenzhen AEE Technology Co., Ltd. FCC ID: TW4AT101 EUT inside whole view Main & RF board component side Main & RF board solder side

The test report consists 26 pages in total. It may be duplicated completely for legal use with the allowance of the applicant. It shall not be reproduced except in full, without the written approval of Ke Mei Ou Laboratory Corporation. The test result in the report only applied to the tested sample. FCC TEST REPORT Under FCC 15 Subpart C, Paragraph 15.249: 2003 Prepared For : Shenzhen AEE Technology Co., Ltd. 1 st Floor B Building Shenzhen Tsinghua Hi-Tech Park Nanshan Hi-Tech Park North Shenzhen P.R.C January 16, 2006 FCC ID: TW4AT101 EUT: 2.4G Wireless Camera Kit Model: AT101 Report Type: Original Report Test Engineer: Peter Lin Test Date: January 4, 2006 Review By: Apollo Liu / Manager FEDERAL COMMUNICATIONS COMMISSION Registration Number: 125782 INDUSTRY CANADA Registration Number: IC4986 Ke Mei Ou Laboratory Co., Ltd. 7A, Jiaxiangge, Jiahuixincheng, No.3027, Shennan Rd., Futian, Shenzhen, Guangdong, P.R.China. Zip Code: 518033 Tel: + 86 755 83642690 Fax: + 86 755 83297077 www.kmolab.com Shenzhen AEE Technology Co., Ltd. FCC ID: TW4AT101 KMO FCC ID Report Report #: KSZ2005122601J Page 2 of 26 TABLE OF CONTENTS 1. General Information....................................................................................................................................................3 1. 1 Notes......................................................................................................................................................................3 1. 2 Testing Laboratory..................................................................................................................................................3 1. 3 Details of Applicant................................................................................................................................................3 1. 4 Application Details..................................................................................................................................................3 1. 5 Test Item.................................................................................................................................................................3 1. 6 Test Standards.........................................................................................................................................................3 2. Technical Test...............................................................................................................................................................4 2. 1 Summary of Test Results.........................................................................................................................................4 3. EUT Modifications.......................................................................................................................................................4 4. Conducted Power Line Test.........................................................................................................................................5 4. 1 Test Equipment.......................................................................................................................................................5 4. 2 Test Procedure........................................................................................................................................................5 4. 3 Test Setup...............................................................................................................................................................5 4. 4 Configuration of the EUT........................................................................................................................................6 4. 5 EUT Operating Condition........................................................................................................................................7 4. 6 Conducted Power Line Emission Limits..................................................................................................................7 4. 7 Conducted Power Line Test Result...........................................................................................................................8 5. Radiated Emission Test..............................................................................................................................................10 5. 1 Test Equipment.....................................................................................................................................................10 5. 2 Test Procedure......................................................................................................................................................10 5. 3 Radiated Test Setup...............................................................................................................................................10 5. 4 Configuration of the EUT......................................................................................................................................11 5. 5 EUT Operating Condition......................................................................................................................................11 5. 6 Radiated Emission Limit.......................................................................................................................................11 5. 7 Radiated Emission Test Result...............................................................................................................................12 6. Band Edge..................................................................................................................................................................14 6. 1 Test Equipment.....................................................................................................................................................14 6. 2 Test Procedure....................................................................................…

Text truncated - open the document above for the full version.

Applicant: Shenzhen AEE Technology Co., Ltd. FCC ID: TW4AT101 Conducted emission test view Radiated emission test view