U4A-SCYMCA1KAperio V3 IN100 Keypad Variant RF Module

Bored Lock A8189-5 06/23 Attention Installer: Please read these instructions carefully to prevent missing important steps. Improper installations may result in damage to the lock and void the factory warranty. The accuracy of the door preparation is critical for proper functioning and security of this lock. Misalignment can cause premature wear and a lessening of security. Installation Instructions For specific security information, please contact your local ASSA ABLOY Door Security Solutions sales consultant or call 800-810-9473. Copyright © 2020-23 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Patent pending and/or patent - www.assaabloydss.com/patents. HID, iCLASS, and Edge are trademarks or registered trademarks of HID Global Corporation. IN IN100 Series (with Aperio™ Technology) Copyright © 2019, 2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 06/30/23 A8189-5 • 800-810-9473 • www.sargentlock.com 2 Installation Instructions Bored Lock IN100 Series 1 3 2 Table of Contents 5 6 4 7 8 9 Warning ..................................................................................................................3 Product & Technical Specifications .....................................................................4 Product Illustrations .............................................................................................5 Lock Installation ....................................................................................................7 Operational Check ..............................................................................................16 Communication Hub LED Indications ..............................................................17 Lock LED Indications ...........................................................................................18 Lock Self-Test LED Indications ............................................................................19 Lock Busy LED Indications ..................................................................................20 06/30/23 A8189-5 • 800-810-9473 • www.sargentlock.com3 Copyright © 2019, 2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Installation Instructions Bored Lock IN100 Series 1Warning Changes or modifications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment. FCC: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Industry Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.” Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT M…

Text truncated - open the document above for the full version.

A8208-5 09/23 Attention Installer: Please read these instructions carefully to prevent missing important steps. Improper installations may result in damage to the lock and void the factory warranty. The accuracy of the door preparation is critical for proper functioning and security of this lock. Misalignment can cause premature wear and a lessening of security. Installation Instructions For specific security information, please contact your local ASSA ABLOY Door Security Solutions sales consultant or call 800-810-9473. Copyright © 2020-23 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Patent pending and/or patent - www.assaabloydss.com/patents. HID, iCLASS, and Edge are trademarks or registered trademarks of HID Global Corporation. IN100 Series PE80 Series and 80 Series Exit Devices includes Rim & Mortise (with Aperio ® Technology) IN IN100 Series Exit Device Copyright © 2019-2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 09/30/23 A8208-5 • 800-810-9473 • www.sargentlock.com 2 Table of Contents All images in document are 80 Series Warning ..........................................................................................................................3 Product & Technical Specifications .............................................................................4 Product Illustrations ......................................................................................................5 Installation Instructions for: 8800 & PE8800 Rim Exit Device .................................................................................10 8900 & PE8900 Mortise Exit Device ..........................................................................15 PE8600 Concealed Vertical Rod Exit Device (EA Option) .......................................22 PE8700 Surface Vertical Rod Exit Device (EA Option) .............................................26 IN100 Installation ........................................................................................................30 Operational Check ......................................................................................................33 Communication Hub LED Indications .......................................................................34 Lock LED Indications ...................................................................................................35 Lock Self-Test LED Indications ....................................................................................36 Lock Busy LED Indications ..........................................................................................37 3 2 5 6 7 8 9 10 11 12 13 1 4 IN100 Series Exit Device 09/30/23 Copyright © 2019-2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. A8208-5 • 800-810-9473 • www.sargentlock.com 3 1Warning Changes or modifications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment. To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components: • Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door. • Leave components (reader and controller) protected in their respective anti-static bags until ready for installation • Do not touch pins, leads or solder connections on the circuit boards This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.P65warnings.ca.gov. Ce produit peut vous exposer au plomb qui, dans l’état de la Californie, est reconnu pour causer le cancer, des anomalies congénitales ou d’autres problèmes de reproduction. Pour plus d’informations, visitez: www.P65warnings.ca.gov. Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. General Regulatory Compliance: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil contient des émetteurs/réceptuers exemptés de licence conformes aux RSS d’Innovation, Sciences et Développment économique Canada. Cet appareil est conforme à la section 15 de la réglementation de la FCC. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. This equipment complies with FCC and IC radiation exposure limits set forth for general population (uncontrolled environment). This device must not be co- located or operating in…

Text truncated - open the document above for the full version.

A8190-6 06/23 Attention Installer: Please read these instructions carefully to prevent missing important steps. Improper installations may result in damage to the lock and void the factory warranty. The accuracy of the door preparation is critical for proper functioning and security of this lock. Misalignment can cause premature wear and a lessening of security. Installation Instructions For specific security information, please contact your local ASSA ABLOY Door Security Solutions sales consultant or call 800-810-9473. Copyright © 2020-23 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Patent pending and/or patent - www.assaabloydss.com/patents. HID, iCLASS, and Edge are trademarks or registered trademarks of HID Global Corporation. IN IN100 Series Mortise Lockset (with Aperio™ Technology) Installation Instructions Mortise Lock IN100 Series 2 1-800-810-9473 • www.sargentlock.com • A8190-6 Copyright © 2019, 2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 1-800-810-9473 • www.sargentlock.com • A8190-6 3 06/30/23 Table of Contents Warning ..................................................................................................................3 Product & Technical Specifications .....................................................................4 Product Illustrations .............................................................................................5 Lock Installation ....................................................................................................7 Operational Check ..............................................................................................16 Communication Hub LED Indications ..............................................................17 Lock LED Indications ...........................................................................................18 Lock Self-Test LED Indications ............................................................................19 Lock Busy LED Indications ..................................................................................20 1 3 2 5 6 4 7 8 9 2 1-800-810-9473 • www.sargentlock.com • A8190-6 06/30/23 1-800-810-9473 • www.sargentlock.com • A8190-6 3 Copyright © 2019, 2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Installation Instructions Mortise Lock IN100 Series 1Warning Changes or modifications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment. FCC: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Industry Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.” Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. Any retrofit or other…

Text truncated - open the document above for the full version.

L. Page Heslin General Counsel and Secretary Americas Division ASSA ABLOY Americas Phone: +1 203 499 6868 110 Sargent Drive Fax: +1 498 5592 New Haven, CT 06511 Mobile: +1 203 376 5977 Email: [email protected] Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to 47 CFR part §2.911(d)(7) of the FCC rules To whom it may concern, This letter is to certify that ASSA ABLOY Inc. (“Applicant”) accepts responsibilities to act as its own agent pursuant to 47 CFR part §2.911(d)(7) of the FCC rules for service of process. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated below. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : ASSA ABLOY Inc. Contact Name : L. Page Heslin Address : 110 Sargent Drive, New Haven, CT 06511 Telephone No : 203-499-6868 Email : [email protected] FCC ID : U4A-SCYMCA1K Applicant FRN : 0021548276 Signature: Date: __05/01/2024____________________________

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: ASSA ABLOY, Inc. FCC ID: U4A-SCYMCA1K To whom it may concern, ASSA ABLOY, Inc. (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. James W. Forte, P.E. Senior Product Compliance Engineer ASSA ABLOY, Inc. 05/01/2024

Attention: Application Examiner Re: Request for confidentiality Applicant: ASSA ABLOY, Inc. FCC ID: U4A-SCYMCA1K To whom it may concern, Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request is hereby submitted by ASSA ABLOY, Inc. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: • Schematics • Detailed Block diagrams • Detailed Operational/Functional Description Rationale for request for confidentiality: ASSA ABLOY, Inc. has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. The fee for confidentiality has been submitted along with the fee for certification. If you have questions or need further information, please contact the undersigned. Sincerely, James W. Forte, P.E. Senior Product Compliance Engineer ASSA ABLOY Inc.

IN100 Keypad Variant Host Photos External Inside (Secured Side) of Door Exterior (Unsecured Side) of Door All Plastic Cover – Keypad Variant Exterior (Unsecured Side) of Door Plastic Cover with Metal Wings -Keypad Variant Exterior (Unsecured Side) of Door All Plastic Cover – Non Keypad Variant Exterior (Unsecured Side) of Door Plastic Cover with Metal Wings – Non Keypad Variant

INCH MM 63 X.X X.XX X.XXX ANGLES FRACTIONS SURFACE FINISH UNLESS OTHERWISE SPECIFIED TOLERANCES .03 .01 .005 0°30' 1/64 4 DISASSEMBLY OF 52-4871TAB 1 NON-KEYPAD VERSIONS (BIPS) 1a 4X 1c 1b 12 NON-KEYPAD VERSIONS (BIPS) KEYPAD VERSIONS (BIKPS) 1a 4X 1b 1c 5 5 2 2 3 2X 12 KEYPAD VERSIONS (BIKPS) 6 METAL WING VERSIONS (-MB) 1b 1a 4X 4 NON-KEYPAD VERSIONS (BIPS) 1a 4X 1b 3 2X 4 KEYPAD VERSIONS (BIKPS) 3 ALL BLACK PLASTIC VERSIONS (-B) 4 1 NOTES: THESE PART NUMBERS ARE FOR SARGENT COMPONENT PACKS. BOM ONLY, NO ASSEMBLY.1. REMOVE READER ASSEMBLY 1 FROM PACKAGING (BOX & ANTI-STATIC BAG). RETAIN PACKAGING FOR LATER USE.2. FOR ALL BLACK PLASTIC VERSIONS (-B) ONLY: SKIP DIRECTLY TO NOTE 9.3. UNSCREW SCREWS 1a 4X AND DISASSEMBLE, AS SHOWN. KEEP ELECTRONICS, PLATE, AND KEYS (FOR KEYPAD VERSION) 1b TOGETHER.4. DISCARD ORIGINAL READER COVER 1c .5. FOR METAL WING VERSIONS ONLY: SLIDE FINISHED WINGS 3 2X ONTO READER FRONT FACE & LENS 2 .6. PLACE READER ASSEMBLY ELECTRONICS 1b FROM STEP 4 INTO READER FRONT FACE & LENS FROM PREVIOUS STEP.7. SECURE READER TOGETHER WITH SCREWS 1a 4X (REMOVED IN STEP 4).8. SCREW TORQUE: 0.45 - 0.68 Nm (4.0 - 6.0 INCH-POUND). DO NOT OVER-TIGHTEN. APPLY READER LABEL 4 OVER EXISTING LABEL ON READER PLATE, AFTER TESTING.9. SEE LABEL DRAWING FOR APPROPRIATE LABEL INFORMATION. PLACE FULLY ASSEMBLED READER BACK IN ANTI-STATIC BAG, THEN IN BOX. 10. APPLY MODULE LABEL 5 WITH NEW INFORMATION OVER EXISTING MODULE LABEL ON BOX.11. SEE LABEL DRAWING FOR APPROPRIATE LABEL INFORMATION. LABEL COLOR ON WIRE HARNESS DENOTES READER SERIES: RED FOR IN120/220, BLUE FOR IN100.12. MATERIAL AND MANUFACTURING PROCESS MUST COMPLY WITH ASSA ABLOY AMERICAS PRODUCT COMPLIANCE SPECIFICATION DOCUMENT ID# D00111736013. ITEM DRAWING NO. SARGENT PART NO. CORBIN RUSSWIN PART NO. DESCRIPTION SERIESIN120/220IN100 READER - COLOR & STYLE BIPS-BBIKPS-BBIPS-MBBIKPS-MBBIPS-MBBIKPS-MBBIPS-BBIKPS-BBIPS-MBBIKPS-MBBIPS-MBBIKPS-MB SARGENT P/N52-641052-641152-641252-641352-641452-641552-641652-641752-641852-641952-642052-6421 CORBIN RUSSWIN P/N890F509890F519890F525890F535--890F549890F559890F565890F575-- 152-4871TAB 52-4871886F599READER ASSEMBLY - IN120/IN220 - NO KEYPAD - BLACK1-1-1------- 52-4872886F609READER ASSEMBLY - IN120/IN220 - KEYPAD - BLACK-1-1-1------ 52-4873886F619READER ASSEMBLY - IN100 - NO KEYPAD - BLACK------1-1-1- 52-4874886F629READER ASSEMBLY - IN100 - KEYPAD - BLACK-------1-1-1 252-1970TAB 52-1974886F549READER FRONT FACE & LENS - NO KEYPAD - BLACK W/ WINGS--1-1---1-1- 52-1976886F569READER FRONT FACE & LENS - KEYPAD - BLACK W/ WINGS---1-1---1-1 3-52-1978886F585 FINREADER WING--22----22-- 4-52-1985889F659READER LABEL111111111111 552-1540TAB52-1708-MODULE LABEL (NOT SHOWN)111111111111 NOTES: 3 36611336611 REVISIONS ZONEREV.DESCRIPTIONDATEENG 1ORIGINAL RELEASE PER EN XXXXXX/XXXXXX5/19/2023RL E B A A B C D 87654 DRAWN BY riclei MATERIAL SEE BOM V10_7/16/2020 SURFACE/FINISH THIRD ANGLE PROJECTION C HEAT TREATMENT DRAWING COMPLIES WITH ASME Y14.5M - 1994 NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFORMATION The material disclosed herein is the confidential and proprietary information of Sargent Manufacturing Company (the “Company”). This drawing and/or technical information is issued in confidence for engineering information only and may not be reproduced or used to manufacture anything, including the items shown or referred to hereon, without direct written permission from the Company. This drawing and/or technical information is the property of the Company and is loaned for mutual assistance to be returned when its purpose has been served or upon the request of the Company. LEGACY ID SHEET 1 OF 1 FINAL READER ASSEMBLY IN SERIES CONFIGURATION _Dis-assemble Step - no KP 4 8 65 DRAWING NUMBER (ALT ID) VOLUME 5.440 in³ SURFACE AREA 210.811 in² SIZE C DATE CREATED 10/18/2022 DESIGNED BY riclei REV 1 SCALE 1:2 DOCUMENT ID D001408315-000 MASS 0.359 lb E F G H 7 D F G H 123 New Haven, CT Sargent Manufacturing Company Work In Progress

IN100 Keypad Variant Host Photos Internal IN100 Non Keypad Variant Host Photos Internal

SARGENT MANUFACTURING CO. MPE CALCULATION REPORT SCOPE OF WORK MPE Calculation of Aperio RF Module, Model IN100 REPORT NUMBER 105746284BOX-001mpe.1 ISSUE DATE REVISION DATE April 30, 2024 June 3, 2024 DOCUMENT CONTROL NUMBER Non-Specific Radio Report Shell Rev. December 2017 © 2017 INTERTEK Non-Specific Radio Report Shell Rev. December 2017 Page 2 of 11 Client: Sargent Manufacturing Co. – Model: IN100 MPE CALCULATION REPORT (FULL COMPLIANCE) Report Number: 105746284BOX-001mpe.1 Project Number: G105746284 Report Issue Date: April 30, 2024 Report Revision Date: June 3, 2024 Model(s) Tested: IN100 Standards: FCC Part 1 Subpart I, April 2021 Procedures Implementing the National Environmental Policy Act of 1969 §1.1307 Actions that may have a significant environmental effect, for which Environmental Assessments (EAs) must be prepared. ISED RSS-102 Issue 6 December 15, 2023 Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) Tested by: Client: Intertek 70 Codman Hill Road Boxborough, MA 01719 USA Sargent Manufacturing Co. 110 Sargent Drive New Haven, CT 6511 USA Report prepared by Report reviewed by Kouma Sinn / Sr. EMC Staff Engineer Vathana Ven / Sr. EMC Staff Engineer This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Report Number: 105746284BOX-001mpe.1 Issued: April 30, 2024 Revised: June 3, 2024 Non-Specific Radio Report Shell Rev. December 2017 Page 3 of 11 Client: Sargent Manufacturing Co. – Model: IN100 Table of Contents 1 Introduction and Conclusion ..................................................................................................................... 4 2 Evaluation Summary ................................................................................................................................ 4 3 Client Information .................................................................................................................................... 5 4 Description of Equipment Under Test and Variant Models ......................................................................... 5 5 Power Density Calculation ........................................................................................................................ 6 6 ISED RSS-102 Issue 5 §2.5.2 Exemption ...................................................................................................... 9 7 Revision History ..................................................................................................................................... 11 Intertek Repo…

Text truncated - open the document above for the full version.