V7T268R150Mbps Wireless‐N Router

11N Wireless Broadband Router User Guide 1 Wireless-N Broadband Router W268R Notice RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. 11N Wireless Broadband Router User Guide 2 Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co., Ltd, any individual or party is not allowed to copy, plagiarize, reproduce or translate it into other languages. All the photos and product specifications mentioned in this manual are for references only. Upgrades of software and hardware may occur, and if there are changes, Tenda is not responsible for notifying in advance. If you would like to know more about our product information, please visit our website at www.tenda.cn. 11N Wireless Broadband Router User Guide 3 11N Wireless Broadband Router User Guide 4 11N Wireless Broadband Router User Guide 5 11N Wireless Broadband Router User Guide 1 Chapter 1 Product Introduction Thank you for purchasing the Tenda W268R Wireless Broadband Router! This easy-to-use router provides simple configuration interface which enables you to configure it with ease. It is based on the latest IEEE802.11n standard, and is backward compatible with devices of IEEE802.11b/g standards. The W268Rincluding router, wireless AP, four-port switch and firewall in oneprovides powerful online monitor function and supports URL filter and MAC filter. With WDS function, it can repeat and amplify wireless signals so as to enlarge network coverage area. It truly supports UPnP and WMM to make your audio and video smoother. With QoS function, it can efficiently distribute the downloading rate for the clients. Additionally, with super compatibility, the router can break the access limits in some areas so that multiple computers can share the Internet access. 11N Wireless Broadband Router User Guide 2 1.1 Package Contents Please verify the following items after you open the package: ¾ One W268R Wireless Broadband Router ¾ One Quick Installation Guide ¾ One Power Adapter ¾ One Software CD If any of the listed items are missing or damaged, please contact the Tenda reseller for immediate replacement. 1.2 LED Indicators and Port Description Panel and LED indicators show: 11N Wireless Broadband Router User Guide 3 LED indicator description on the front panel Back panel port show 11N Wireless Broadband Router User Guide 4 Back panel port description 11N Wireless Broadband Router User Guide 5 Chapter 2 Product Installation 1. Please use only the included power adapter to power your router. (NOTE: Use of an unmatched power adapter could cause damage to this product). 2. Please connect the router’s LAN port to your computer with an Ethernet cable as shown below. 11N Wireless Broadband Router User Guide 6 3. Please connect your broadband line provided by your ISP to the router’s WAN port. 4. Insert the included software CD into the CD drive of your computer. After the software automatically initiates, double click the “Setup” icon and follow the instructions to complete the installation. You can also enter the router’s Web-based Utility to complete the configuration. 11N Wireless Broadband Router User Guide 7 Chapter 3 How to configure to access the Internet 3.1 How to Set the Network Configurations Network Configurations under windows XP 1. Right click “My Network Places” on your computer desktop and select “Properties”. 2. Right click “Local Area Connection” and select “Properties”. 11N Wireless Broadband Router User Guide 8 3. Select “Internet Protocol (TCP/IP)” and click “Properties”. 4. Select “Obtain an IP address automatically” and 11N Wireless Broadband Router User Guide 9 “Obtain DNS server address automatically”. Click “OK” to save the configurations. Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as follows: ¾ IP Address: 192.168.0.XXX: (XXX is a number from 2~254) ¾ Subnet Mask: 255.255.255.0 ¾ Gateway: 192.168.0.1 ¾ DNS server: You should input the DNS server address provided by your ISP. Otherwise, you can enter 192.168.0.1. Click “OK” to save the configurations. 11N Wireless Broadband Router User Guide 10 Network Configurations under windows 7 1. Click the network icon on the lower right corner of your computer desktop, and then click” Open Network and Sharing Center”. 11N Wireless Broadband Router User Guide 11 2. Click “Change adapter settings” on the left side of the window. 3. Right click “Local Area Connection” and select “Properties”. 11N Wireless Broadband Router User Guide 12 4. Double click” Internet Protocol Version 4(TCP/IPv4)". 11N Wireless Broadband Router User Guide 13 5. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click “OK” to save the configurations. Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as follows: 11N Wireless Broadband Router User Guide 14 ¾ IP Address: 192.168.0.XXX: (XXX is a number from 2~254) ¾ Subnet Mask: 255.255.255.0 ¾ Gateway: 192.168.0.1 ¾ DNS server: You should input the DNS server address provided by your ISP. Otherwise, you can enter 192.168.0.1. Click “OK” to save the configurations. 3.2 Log in to the Router 1. To access the Router’s Web-based Utility, launch a web browser such as Internet Explorer or Firefox and enter http://192.168.0.1. Press “Enter”. 11N Wireless Broadband Router User Guide 15 2. Type “admin” in the “Password” field. Click “OK”. 3. If you enter the correct password, you will come to the router’s web-based utility as is shown below. 11…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 SHENZHEN TENDA TECHNOLOGY CO., LTD 2011-8-18 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, SHENZHEN TENDA TECHNOLOGY CO., LTD hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): (150Mbps Wireless‐N Router, W268R) We affirm that between SIEMIC and SHENZHEN TENDA TECHNOLOGY CO., LTD any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Liao bin/ Engineer E-mail: : [email protected] Phone: 86-755-27657068 Fax: 86-755-27657178 Address : Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao'an District, Shenzhen, China 518108

SCS-F19: Confidentiality Request Letter Rev 1.0 Nov 14, 2006 Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 SCS-F19: Confidentiality Request Letter Rev 1.0 Nov 14, 2006 SHENZHEN TENDA TECHNOLOGY CO., LTD (2011-9-7) To: Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: V7T 268R We here by request confidential treatment of information accompanying this application as outlined below: - Block diagram - Operation description - Schematic The applicant understands that pursuant to Section 0.457 and 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Liao bin/ Engineer E-mail: : [email protected] Phone: 86-755-27657068 Fax: 86-755-27657178 Address : Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao'an District, Shenzhen, China 518108

SHENZHEN TENDA TECHNOLOGY CO., LTD Date: 2011-08-18 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: V7T2 68R To Whom It May Concern: This letter is to ascertain that SHENZHEN TENDA TECHNOLOGY CO., LTD, 150Mbps Wireless‐N Router has been the units used for conducting FCC compliance testing, the DoC part will be tested by FCC recognized test lab. If you have any question or concerns, pls. contact us. Sincerely, Liao bin/ Engineer E-mail: : [email protected] Phone: 86-755-27657068 Fax: 86-755-27657178 Address : Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao'an District, Shenzhen, China 518108

External of EUT

FCC ID Label FCC ID: V7T268R Model Number: W268R Made in China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Label Location Proposed Label Location on EUT

Internal of EUT Antenna WiFi Module

RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure(MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300-1500 -- -- F/1500 6 1500-100000 -- -- 1 30 11.1 Friis transmission formula: Pd=(Pout*G)\(4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= gain of antenna in linear scale Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1mW/cm 2 . If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. 11.2 Measurement Result Antenna gain: 2 dBi 802.11b Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) gain of antenna in linear scale G Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 1 2412.00 14.26 26.669 1.585 0.008 1 6 2437.00 14.19 26.242 1.585 0.008 1 11 2462.00 14.57 28.642 1.585 0.009 1 802.11g Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) gain of antenna in linear scale G Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 1 2412.00 12.69 18.578 1.585 0.006 1 6 2437.00 12.55 17.989 1.585 0.006 1 11 2462.00 12.83 19.187 1.585 0.006 1 802.11n HT20 Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) gain of antenna in linear scale G Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 1 2412.00 12.61 18.239 1.585 0.006 1 6 2437.00 12.26 16.827 1.585 0.005 1 11 2462.00 12.75 18.836 1.585 0.006 1 802.11n HT40 Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) gain of antenna in linear scale G Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 3 2422.00 11.87 15.382 1.585 0.005 1 6 2437.00 11.68 14.723 1.585 0.005 1 9 2452.00 11.59 14.421 1.585 0.005 1

SHENZHEN EMTEK CO., LTD. REPORT NO: ES110728180F FCC ID: V7T268R DATE: 08/18/2011 Page 1 of 68 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF 150Mbps Wireless‐N Router MODEL No.: W268R FCC ID: V7T268R REPORT NO: ES110728180F ISSUE DATE: August 18, 2011 Prepared for SHENZHEN TENDA TECHNOLOGY CO., LTD Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao’an District, Shenzhen, P.R.China 518108 Prepared by SHENZHEN EMTEK CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 SHENZHEN EMTEK CO., LTD. REPORT NO: ES110728180F FCC ID: V7T268R DATE: 08/18/2011 Page 2 of 68 VERIFICATION OF COMPLIANCE Applicant: SHENZHEN TENDA TECHNOLOGY CO., LTD Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao’an District, Shenzhen, P.R.China 518108 Manufacturer: SHENZHEN TENDA TECHNOLOGY CO., LTD Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao’an District, Shenzhen, P.R.China 518108 Trademark: N/A Product Description: 150Mbps Wireless‐N Router Model Number: W268R File Number: ES110728180F Date of Test: August 3, 2011 to August 18, 2011 We hereby certify that: The above equipment was tested by SHENZHEN EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247. The test results of this report relate only to the tested sample identified in this report. Date of Test : August 3, 2011 to August 18, 2011 Prepared by : (Engineer) Reviewer : (Quality Manager) Approve & Authorized Signer : (Manager) SHENZHEN EMTEK CO., LTD. REPORT NO: ES110728180F FCC ID: V7T268R DATE: 08/18/2011 Page 3 of 68 Ta b l e o f C o n t e n t s 1. GENERAL INFORMATION................................................................................................... 5 1.1 P RODUCT DESCRIPTION......................................................................................................... 5 1.2 R ELATED SUBMITTAL(S) / GRANT(S) ..................................................................................... 5 1.3 T EST METHODOLOGY............................................................................................................ 6 1.4 S PECIAL ACCESSORIES.......................................................................................................... 6 1.5 E QUIPMENT MODIFICATIONS................................................................................................. 6 1.6 T EST FACILITY...................................................................................................................... 6 2. SYSTEM TEST CONFIGURATION...................................................................................... 7 2.1 EUT CONFIGURATION........................................................................................................... 7 2.2 EUT EXERCISE...................................................................................................................... 7 2.3 T EST PROCEDURE.................................................................................................................. 7 2.4 C ONFIGURATION OF TESTED SYSTEM.................................................................................... 7 3. DESCRIPTION OF TEST MODES ........................................................................................ 9 4. SUMMARY OF TEST RESULTS ......................................................................................... 10 5. CONDUCTED EMISSIONS TEST....................................................................................... 11 5.1 M EASUREMENT PROCEDURE............................................................................................... 11 5.2 T EST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)....................................................... 11 5.3 M EASUREMENT EQUIPMENT USED...................................................................................... 11 5.4 C ONDUCTED EMISSION LIMIT............................................................................................. 12 5.5 M EASUREMENT RESULT...................................................................................................... 12 5.6 C ONDUCTED MEASUREMENT PHOTO.................................................................................. 13 6. RADIATED EMISSION TEST.............................................................................................. 14 6.1 M EASUREMENT PROCEDURE............................................................................................... 14 6.2 T EST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)....................................................... 14 6.3 M EASUREMENT EQUIPMENT USED...................................................................................... 15 6.4 R ADIATED EMISSION LIMIT................................................................................................. 15 6.5 M EASUREMENT RESULT...................................................................................................... 16 6.6 R ADIATED MEASUREMENT PHOTOS.................................................................................... 40 7. OCCUPIED BANDWIDTH TEST........................................................................................ 41 7.1 M EASUREMENT PROCEDURE............................................................................................... 41 7.2 T EST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)....................................................... 41 7.3 M EASUREMENT EQUIPMENT USED...................................................................................... 41 7.4 M EASUREMENT RESULTS....................…

Text truncated - open the document above for the full version.

RADIATED EMISSION TEST CONDUCTED EMISSION TEST