V7TMESH12AC2100 Tri-band Whole Home Mesh WiFi System

Connect the primary node 1. Power off your modem, and remove its battery (if any). 2. Use the included Ethernet cable to connect a LAN port of your modem or the Ethernet jack to the (WAN/LAN) port of any node. This node is your primary node. 4. Use the included power adapter to connect the primary node to a power source. Its LED indicator lights solid green. Wait about for 40 seconds. The system completes startup when the LED indicator blinks green. 3. Reinstall the battery of your modem, and power it on. * The first node you set up functions as the primary node, while the rest are referred to as the secondary nodes. II Set up the primary node for internet access 1. Go to the WiFi network list on your mobile device; select the SSID of the primary node, and enter its password. The default SSID and password are specified on the bottom label of any node. 2. Run the Tenda WiFi App and follow the onscreen instructions to set up the primary node. After the primary node is connected to the internet, its LED indicator lights solid green. III 1. Place each node: − In an elevated, open position within the coverage area of your existing nova WiFi network. − Keep your nodes away from electronics with strong interference, such as microwave oven, induction cooker, and refrigerator. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Operations in the 5.15-5.25GHz band are restricted to indoor use only. This equipment should be installed and operated with minimum distance 20cm between the device and your body. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable. Declaration of Conformity Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type Mesh12, MW12 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.tendacn.com/en/service/download-cata-101.html For EU/EFTA, this product can be used in the following countries: Download and install the Tenda WiFi App I Download the Tenda WiFi App on your mobile device by searching for Tenda WiFi in App Store/Google Play, or by scanning the QR code. Then, install the App. Tenda WiFi Available for and iOSAndroid Or 2. Use the other power adapters to connect the remaining secondary nodes to separate power sources, and their LED light solid green. Wait for about 40 seconds. The secondary node is connecting to another node when its LED indicator blinks green. 3. Observe the LED indicators of the secondary nodes until their LED indicators light one of the following colors: 4. If the LED indicator of a node does not light solid green, relocate it according to step in IV to get better connection. Solid green Good connection Solid yellow Fair connection Solid red Disconnected FAQ Quick Installation Guide Copyright © 2019 Shenzhen Tenda Technology Co., Ltd. All rights reserved. is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice. *MW12 is a serial name coming with one, two or three Mesh12. Technical Support Shenzhen Tenda Technology Co., Ltd. 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 USA hotline: 1-800-570-5892 Toll Free: 7 x 24 hours Canada hotline: 1-888-998-8966 Toll Free: Mon-Fri 9 am - 6 pm PST Hong Kong Hotline: 00852-81931998 Website: www.tendacn.com Email: [email protected] A1: Run the Tenda WiFi App, tap Settings in the lower-right corner, tap Wireless Settings, change your SSID and password, and tap Save. Then, you need to reconnect your mobile devices using the new SSID and password. A2: Tap the node on the Tenda WiFi App, tap “...” in the upper-right corner, and choose “Delete”. Note: Removing operation restores the node to factory settings. A 4: With the nodes powered on, hold the Reset button of your primary node down using a paper clip for about 6 seconds, release when the LED indicator blinks fast. Your network is reset successfully when the LED indicator lights solid on then blinks again. And all nodes are restored to factory settings A3: Yes. Run the Tenda WiFi App, tap Settings in the lower-right corner, tap Add Nova, and follow the on-screen instructions to add. Q1: How can I change my SSID and password? Q2: How can I remove node from my WiFi network? Q4: How to restore my network to factory settings? Q3: Can I add another new set of node to expand my network coverage? Done. To access the internet with: − Wired devices: Connect wired devices to the LAN ports of any node. − Wireless devices: Connect wireless devices to the WiFi network using the SSID and the WiFi password you set. If you want to manage the network anytime, anywhere, tap and use your account to login. Operating Environment Temperature: 0°C-40°C Humidity: (10 - 90)% RH, non-condensing Adapter Model: BN067-A18012E/BN067-A18012U/BN074-A18012B Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD. Input: 100 – 240V AC 50/60Hz 0.6A Output: 12V DC 1.5A : DC Voltage This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment. BEBGCZDKDEEE IE ELESFRHRITCYLV L…

Text truncated - open the document above for the full version.

         !!""#$%&   '(  )**)  +" , - !  "  "   ,    ,   -. "  / + 0"0 !, + +  . , 12  !!"" (3 "+ +)"- !  4   + '  , +   ,  "   ! ..,    !" + +!!  "   ' +. !5"6 ! +7( ) 5"6 8 !!"  .  9)** $: !  0" & ," ,.!" +  0")9 0 )9 0 )9 0 )9 0)9 !; ! &2<70)9 :   9 *9*$*7$*9  ,      &    +   + = ========= >?@ABC DEFCGAHIJKALM?KNOOPQQRJSP@J?T UVWXYZ[Y\\]^_`a^bc^dce[fg^cc\ZhciZjgc[kZ[^dcf`^dZ[ ]lchfmcg^n

            !    "#$"%&'()&'(*'(+,*'-&(./.0 1-.23/*+2 4  56789::;3*:<=;'>3(:2?@@?3)A:BCDAEBFGEB H:EI3(EBDAEB+JDK;JLK  $%A=BMA=B   $-AJBE   *:N* =9=OJLEKJ:BP2QR+=SK28--*-P 'IJD:BDK;EEK?T, 5U@TVW)'Q'(,,H *A=(=KA=;9EBID   %GXY=L KN      $QZ*['%&?T  H=O=;= BL=BG\X=;N]]]]]]   ^_  ?2/:BC 6*=;\-:BOJI=BKJE9JKF     `ab  R`cdefdgehi g$           "   i   h!"    g"  ##      ##    _d e j  _ k! "   l#     #  bi" ! " ^#    4g "        # #   $ i "  hiih  " $g !  " "#   `a   R`adedeR    #g   $#    i  "#$   "    i #     g   "#  i "#  m  g    "#  R     T2%A:; K6*=;\-:BOJI=BKJE9JKFn%*-o      g 4`pqrstuvwxytzz{||{t}~|t€{‚ƒ{}t„…x„vttz€‚†{vwvwxz‡„ˆxv{}‰ !    `aŠR‹ i"#     `aŠR`## i g$   bi ^ "     "   i  h!"   dŒŽ‘’“”e     i •|x„~|–‡}—‡€^ b # i ˜™   i     š           T@T@6@Z6@T" !   ## %A=B1G=   ›‘œ žŸ ¡¢£Ž¤¥¦§ ¡¢£Ž¡ ̈ŽŽ“¥© ̈ª«›¬¥¦§¡Ž§­ Ž­ ̈“­¥® ̄žŒ©¤°±¤£¡Ž§­ Ž­ ̈“­¥­‘­Ž¦¤­Ž¡­¦“§¤²³ ̈¥‘§¤£ ̈§ ́¤ ̈Žμ­¡ ̈Ž’¶Ž  £ ̈¶·­£‘ ̧ ̈“­£¹º ̈¥‘£ ̈¶»ž® ±© ¦“ ̈ŽŽ  ̈‘©¢“ ‘ ̈ ­Ž©¼½¾· ̈¦¦“­¡ ̈­Ž§¤£» ·ž½¿¿£¢‘’­Ž§¤£ ”©Ž£ ̈¤À­Ž ́’ ́­Ž‘ ̈¤“­¤» ²ž¼“ ̈‘ ̈À‘¦“ ̈¡ ̈¢£ ̈­¡ ̈““¥©¢‘¶Ž‘­Ž£¢‘’¤Á¢‘ ­Ž­£»±“§­¡ ̈­Ž ‘Ž¤£­Ž ¥¢§©­‘® ³ž¼Á¢‘§¤¶Ž‘­Ž¤§¤¤“ ̈‘£¢‘’¤¡­ª ’¥±“§­¡ ̈­Ž ̈“ ̈‘¾ ̈¥‘’§¤ ̈§ ̈¡¢ ̈“£ ̈¤À­Ž ́¤’§¤ ¶¦­¤ ̈­Ž§©Œ±¿¦¤­  

          ! " #$%&"'%&"(&")*(&!%"+,+-.!+/,()/ *#01234(5&6"/7887' 9")$:!  %;  <<445#  = #*!>788(1;4%?3$  ( #?7>? 7>? 7>? 7>!?7> (@#(  (  *44A <?4?7>? 7>? 7>? 7>!?7>444 B4C <445 <<# +4 <<4/    )#>8>81 8D18> "#$. (4#201DEE1>D0ED8F2 &14#G/ $# 

       !"#$""!  %&'()*+*+,+-,+*  .(/'0(123 (45672(389:;&2<  #=>?@ =ABCDEFCDEGDE%HGDICEJKJLMIJN/KG%N O!PPAQ,RST994/G9U(4DV/E9NW++W/F092750&2<1&2X9&3/E&250&2%65'468' B0(2Y0(2I062&  %(8T&4('0&' )  Z!#[ "P !>"#AHI*W++G46,\&23.09T(C9:(](50.6S6B<5'(: ^?>P_"#A](50W*/]. W*/]. W*&/]. W*8/I]W* `!AG(23& aAb-G]DBCW*   J2T<80&22(T5WcWWU6TT\(15(362dBHNI912'4<893(5(T(8'69265365&\T(3N   ef<910&g( &2<h1(5'69254(7&43627'0(&1'0946Y&'692/;T(&5(3929'0(56'&'('9892'&8'15/ '0&2i<91c   B628(4(T</     B672&'14()j jjjjjjjjjjjjjjjjjjjjjjj E&:()B0(2M1( G(T)RQ,-kk,*-Qk-+lR D:&6T)8(4'm'(23&N82  

Project No.: 2003C093 Page 2 of 15 Project No.: 2003C093 Page 3 of 15 Project No.: 2003C093 Page 4 of 15 Model: BN067-A18012U Project No.: 2003C093 Page 5 of 15

Project No.: 2003C093 Page 6 of 15 Project No.: 2003C093 Page 7 of 15 Project No.: 2003C093 Page 8 of 15 Project No.: 2003C093 Page 9 of 15 Project No.: 2003C093 Page 10 of 15 5G band 4Ant.2 5G band 4 Ant.1 2.4G & 5G band 1 Ant.2 2.4G & 5G band 1 Ant.1 Project No.: 2003C093 Page 11 of 15 Project No.: 2003C093 Page 12 of 15 Project No.: 2003C093 Page 13 of 15 Project No.: 2003C093 Page 14 of 15 Project No.: 2003C093 Page 15 of 15

Report No.: BTL-FCCP-3-2003C093 Page 1 of 5 FCC RF EXPOSURE REPORT FCC ID: V7TMESH12 Project No. : 2003C093 Equipment : AC2100 Tri-band Whole Home Mesh WiFi System Brand Name : Te n d a Test Model : Mesh12 Series Model : MW12, MW12a, MW12c, CM12 Applicant : SHENZHEN TENDA TECHNOLOGY CO.,LTD Address : 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 Manufacturer : SHENZHEN TENDA TECHNOLOGY CO.,LTD Address : 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 Date of Receipt : Mar. 12, 2020 Date of Test : Mar. 19, 2020 ~ Apr. 09, 2020 Issued Date : Jun. 28, 2020 Report Version : R00 Test Sample : Engineering Sample No.: DG2020031237 Standard(s) : FCC Guidelines for Human Exposure IEEE C95.1 & FCC Part 2.1091 FCC Title 47 Part 2.1091, OET Bulletin 65 Supplement C The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. Prepared by : Nick Chen Approved by : Ethan Ma Add: No.3, Jinshagang 1st Road, Shixia, Dalang Town,Dongguan, Guangdong, China. Tel: +86-769-8318-3000 Web: www.newbtl.com Report No.: BTL-FCCP-3-2003C093 Page 2 of 5 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue Jun. 28, 2020 Report No.: BTL-FCCP-3-2003C093 Page 3 of 5 1. MPE CALCULATION METHOD Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Table for Filed Antenna: For 2.4GHz Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 N/A N/A Internal N/A 3.52 2 N/A N/A Internal N/A 3.52 Note: This EUT supports CDD, and all antennas have the same gain, so, 1) For Non Beamforming, Directional gain=G ANT +Array Gain. For output power measurements, Array Gain=0 (N ANT ≤ 4), so the Directional gain=3.52. For power spectral density measurements, Array Gain=10log(N ANT /N SS ) dB, so the Directional gain=3.52+10log(2/1)=6.53. So, the power spectral density limit is 8-(6.53-6)=7.47. 2) For Beamforming, Beamforming Gain: 3dB. So the Directional gain=3+3.52=6.52. So the output power limit is 30-(6.52-6)=29.48 For 5GHz: Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 N/A N/A Internal N/A 4 2 N/A N/A Internal N/A 4 Note: This EUT supports CDD, and all antennas have the same gain, so, 1) For Non Beamforming, Directional gain=G ANT +Array Gain. For output power measurements, Array Gain=0 (N ANT ≤ 4), so the Directional gain=4. For power spectral density measurements, Array Gain=10log(N ANT /N SS ) dB, so the Directional gain=4+10log(2/1)=7.01. So, the UNII-1 power spectral density limit is 17-(7.01-6)=15.99, the UNII-3 power spectral density limit is 30-(7.01-6)=28.99. 2) For Beamforming, Beamforming Gain: 3dB. So the Directional gain=3+4=7. So the output power limit is 30-(7-6)=29. Report No.: BTL-FCCP-3-2003C093 Page 4 of 5 Table for Antenna Configuration: For 2.4GHz: Non Beamforming: Operating Mode TX Mode 1TX 2TX IEEE 802.11b V (Ant. 1) - IEEE 802.11g V (Ant. 1) - IEEE 802.11n(HT20) - V (Ant. 1+ Ant. 2) IEEE 802.11n(HT40) - V (Ant. 1+ Ant. 2) Beamforming: Operating Mode TX Mode 2TX IEEE 802.11n(HT20) V (Ant. 1+ Ant. 2) IEEE 802.11n(HT40) V (Ant. 1+ Ant. 2) For 5GHz: Non Beamforming: Operating Mode TX Mode 1TX 2TX IEEE 802.11a V (Ant.1) - IEEE 802.11n (HT20) - V (Ant. 1 + Ant. 2) IEEE 802.11n (HT40) - V (Ant. 1 + Ant. 2) IEEE 802.11ac (VHT20) - V (Ant. 1 + Ant. 2) IEEE 802.11ac (VHT40) - V (Ant. 1 + Ant. 2) IEEE 802.11ac (VHT80) - V (Ant. 1 + Ant. 2) Beamforming: Operating Mode TX Mode 2TX IEEE 802.11n (HT20) V (Ant. 1 + Ant. 2) IEEE 802.11n (HT40) V (Ant. 1 + Ant. 2) IEEE 802.11ac (VHT20) V (Ant. 1 + Ant. 2) IEEE 802.11ac (VHT40) V (Ant. 1 + Ant. 2) IEEE 802.11ac (VHT80) V (Ant. 1 + Ant. 2) Report No.: BTL-FCCP-3-2003C093 Page 5 of 5 2. TEST RESULTS For 2.4GHz Non Beamforming: Directional Gain (dBi) Directional Gain (numeric) Max. Output Power (dBm) Max. Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 3.52 2.2491 29.98 995.4054 0.33694 1 Complies For 2.4GHz Beamforming: Directional Gain (dBi) Directional Gain (numeric) Max. Output Power (dBm) Max. Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 6.52 4.4875 26.42 438.5307 0.29618 1 Complies For 5GHz UNII-1 Non Beamforming: Directional Gain (dBi) Directional Gain (numeric) Max. Output Power (dBm) Max. Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 4 2.5119 23.9 245.4709 0.09280 1 Complies For 5GHz UNII-3 Non Beamforming: Directional Gain (dBi) Directional Gain (numeric) Max. Output Power (dBm) Max. Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 4 2.5119 29.93 984.0111 0.37201 1 Complies For 5GHz UNII-1 Beamforming: Directional Gain (dBi) Directional Gain (numeric) Max. Output Power (dBm) Max. Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 7 5.0119 23.94 247.7422 0.18688 1 Complies For 5GHz UNII-3 Beamforming: Directional Gain (dBi) Directional Gain (numeric) Max. Output Power (dBm) Max. Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 7 5.0119 29.37 864.9679 0.65246 1 Complies For the max simultaneous transmission MPE: Power Density (S) (mW/cm 2 ) Power Density (S) (mW/cm 2 ) To t a l Limit of Power Density (S) (mW/cm 2 ) Test Result 2.4GHz 5GHz 0.33694 0.65246 0.9894 1 Complies Note: The calculated distance is 23 cm. End of Test Report

Report No.: BTL-FCCP-2-2003C093 Page 32 of 167 10. EUT TEST PHOTOS AC Power Line Conducted Emissions Test Photos Report No.: BTL-FCCP-2-2003C093 Page 33 of 167 Radiated Emissions Test Photos 9 kHz to 30 MHz Report No.: BTL-FCCP-2-2003C093 Page 34 of 167 Radiated Emissions Test Photos 30 MHz to 1 GHz Report No.: BTL-FCCP-2-2003C093 Page 35 of 167 Radiated Emissions Test Photos Above 1 GHz