V7TRX12PAX3000 Dual Band Gigabit WiFi 6 Router

II. Connect the router to the internetLED indicators&Jack, ports and buttonsI. Connect the router Scenario1: Set up the device as a router Method 2: Setup through web UI The "new router" and "router" in this guide refer to the router in the package. Step 1: Import your PPPoE user name and password into the new router (Optional) 1. Power on your original and new routers. 2. Connect the WAN port of the original router to a LAN port (1, 2 or IPTV/3) of the router using an Ethernet cable. After the LED indicator of the new router blinks fast for 8 seconds, the PPPoE user name and password are imported to your new router. 3. Remove the original router. 1. Connect the client to the router. Method 1: Connect the wireless client such as a mobile phone to the WiFi network of the router. The SSID and password can be found on the bottom label of the device. Method 2: Use an Ethernet cable to connect the computer to the 1, 2 or IPTV/3 port of the router. 3. The router detects your connection type automatically. − If you have imported your PPPoE user name and password into the router, click Next. − If you did not import your PPPoE user name and password into the router, select the ISP Type based on your region and ISP and enter required parameters (if any). Then, click Next. 4. Set the WiFi name, WiFi password and login password for the router. Click Next. To access the internet with: - Wired devices: Connect to the LAN port of your router. - Wireless devices: Connect to your WiFi network using the WiFi name and password you set. 2. Start a browser on the client (computer used as an example) and enter tendawifi.com in the address bar to access the web UI. Then, click Start Now. After the router is powered on for about 40 seconds, the system completes startup. The status of the LED indicator is shown in the following table. Node Type Primary node Secondary node LED indicator Status Description Solid green Blinking green fast Blinking green fast Blinking red slowly Solid green Solid orange Solid red The router is pending for or performing WPS negotiation or Mesh networking. The router failed to connect to the internet. Networking succeeds. Good connection quality. Networking succeeds. Fair connection quality. Networking succeeds. Poor connection quality. Networking by the WPS button or performing WPS negotiation. Blinking green slowly Waiting to connect to another node. Blinking red slowly The router failed to connect the internet. The system is starting up, or the router is already connected to the internet. Done. • To access the internet with: - Wired devices: Connect to the LAN port of your router. - Wireless devices: Connect to your WiFi network using the WiFi name and password you set. • If you want to manage the network remotely, tap on the App home page and use your account to log in. Tips This function is only applicable when the connection type of the original router is PPPoE, except for PPPoE of some special ISPs or PPPoE connection set up manually with VLAN information. Description Jack/Port/ Button Power jack. Please use the included power adapter to connect this jack to a power source for power supply. Reset button. When the router is working normally, hold the button down using a needle-like item (such as a pin) for about 8 seconds, and then release it when the LED indicator blinks red fast. The router is reset. 10/100/1000 Mbps auto-negotiation WAN port. Used to connect to a modem or the Ethernet jack using an Ethernet cable for internet access. After the router is connected to an existing network as a secondary node, this WAN port is used as a LAN port. 10/100/1000 Mbps auto-negotiation LAN port. Used to connect to computers, switches or game machines, etc. POWER WPS RST 1, 2 10/100/1000 Mbps auto-negotiation LAN/IPTV port. It is a LAN port by default. When the IPTV function is enabled, it can only serve as an IPTV port to connect to a set-top box. IPTV/3 WPS/Mesh button. • WPS: When it is used as a WPS negotiation button, you can connect to the WiFi network of the router without entering the WiFi password. Method: Short press the button (for about 1 second), and the LED indicator blinks fast. Within 2 minutes, enable the WPS function of the other WPS-supported device to establish a WPS connection. • Mesh: When it is used as a Mesh networking button, you can extend your network with another device that supports the Mesh function. Method: Press this button for about 3 seconds. The LED indicator blinks green fast, which indicates the device is searching for another device to form a network. Within 2 minutes, press the MESH/WPS button of another device for 1 to 3 seconds to negotiate with this device. WAN AX3000 Dual Band Gigabit Wi-Fi 6 Router RX12 Pro/TX12 Pro Quick Installation Guide • Wireless router x 1 • Power adapter x 1 • Ethernet cable x 1 • Quick installation guide x 1 Package contents Please read this guide before you start with the quick setup upon the first use. This guide instructs how to install and connect the device. For more information such as the description of symbols displayed on relevant materials, please visit www.tendacn.com. Tips 1. Ensure that the router is powered on. 2. Connect the WAN port of the router to the LAN port of your modem or the Ethernet jack using an Ethernet cable. 1. Download the Tenda WiFi App onto your mobile device by scanning the QR code or searching for Tenda WiFi in Google Play or App Store. Then install the Tenda WiFi App. 2. Connect the mobile phone to the WiFi network of the router. The SSID and password can be found on the bottom label of the router. 3. Run the Tenda WiFi App and follow the onscreen instructions to connect the router to the internet. After the router is connected to the internet, its LED indicator lights solid green. Step 2: Connect the WAN port of the routerMethod 1: Setup through Tenda WiFi App Note If you use the modem for internet access, please power off the modem first before connecting the WAN port of the router …

Text truncated - open the document above for the full version.

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

       !"# $%# &## "# '"(')( *  ' # ++, -++,-+-.#/-++,-+-- 0#')(1( #)  234567689:;:<=9>956798? @ABCDEFEEGHFGEI  JK@KLMNOPQQRSTOMUTPSVOPQQTVVTPS MWBXYZ[\AB[Y]A]^K_A`WAB[Y]@[_[a[Y] bcdePAf`A]^Q[``aLYA^ OY`Wgh[AiQ@EHFcI  @CAZV[ZYZQ A^AgD  jCiVkKSlkKSUKS@MUKOkSPNPmnOPoiNU@oiXCZChp^Cq`AZCBXABBXCrZY^WqBDMsdFFF@WA` tA]^m[uAh[Bj[J[ILYWBCZigY^C`DUsHEvZY AZCC`CqBZ[qA``p[^C]B[qA`w[BXBXCgY^C`D LsHEvZYwX[qX wAaBCaBC^hp OX[]AOCZB[x[qAB[Y]TOUOYoiNB^y@Y]uuWA]zw[BXBXCaAgCC`CqBZYgAu]CB[qCg[aa[Y]a A]^C`CqBZYgAu]CB[qqYgrAB[h[`[BpqXAZAqBCZ[aB[qao  M^CaqZ[rB[Y] YxBXC^[xxCZC]qCahCBwCC]BXYaCgY^C`aA]^BXABAZC^Cq`AZC^a[g[`AZAZCAaxY``YwaD UXCpAZCBXCaAgCrZY^WqBiA]^{WaBBXC^[xxCZC]BgY^C`]AgCoBXCZCaBAZCBXCaAgCo UXC^CBA[`[]xYZgAB[Y]ir`CAaCqXCqfBXCZCrYZBao  v`CAaCqY]BAqBgCaXYW`^BXCZChC]CC^xYZA]pA^^[B[Y]A`q`AZ[x[qAB[Y]YZ[]xYZgAB[Y]o  tCaBLCuAZ^ai  V[u]ABWZCD  |' (#0    % '( !'  

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS 2.4G Chain 0 2.4G RX 2.4G Chain 1 5G Chain 0 5G Chain 1

China Certification ICT Co., Ltd (Dongguan) Report No.: CR22080019-00A Page 76 of 76 5. RF EXPOSURE EVALUATION 5.1 Applicable Standard According to §1.1307(b)(3)(i) (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). P th is given by: 5.2 Measurement Result Operation Modes Frequency (MHz) Distance (mm) P th Maximum Conducted Power including Tune-up Tolerance (dBm) Antenna Gain (dBi) ERP (P) (dBm) ERP (P) (mW) Exemption (mW)(dBm) WLAN 2.4G 2412-2462 200 3060 34.86 25.3 8.0 31.15 1303.17 Compliant WLAN 5G 5150-5250 200 3060 34.86 22 9.0 28.85 767.36 Compliant 5250-5350 200 3060 34.86 17 9.0 23.85 242.66 Compliant 5725-5850 200 3060 34.86 25.5 9.0 32.35 1717.91 Compliant Note: Antenna gain includes bearmforming gain. The Maximum Conducted Power including Tune-up Tolerance was declared by manufacturer. WLAN 2.4G and 5G can transmit simultaneously: = P 2.4G /P th-2.4G +P 5G /P th-5G =1303.17/3060+1717.91/3060 =0.99 Result: The device compliant the Exemption at 20cm distances. ===== END OF REPORT =====

TEST REPORT Applicant: SHENZHEN TENDA TECHNOLOGY CO.,LTD. Address: 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 FCC ID: V7TRX12P Product Name: AX3000 Dual Band Gigabit WiFi 6 Router Model Number: RX12 Pro, TX12 Pro Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR22080019-00A Date Of Issue: 2022-10-22 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR22080019-00A Page 2 of 76 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR22080019-00A Page 3 of 76 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 1. GENERAL INFORMATION .................................................................................................... 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 5 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 7 1.2.1 EUT Operation Condition: ............................................................................................................................. 7 1.2.2 Support Equipment List and Details .............................................................................................................. 7 1.2.3 Support Cable List and Details ...................................................................................................................... 7 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 8 1.3 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 2. SUMMARY OF TEST RESULTS .......................................................................................... 10 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 11 3.1.1 Applicable Standard ..................................................................................................................................... 11 3.1.2 EUT Setup.................................................................................................................................................... 12 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 12 3.1.4 Test Procedure ............................................................................................................................................. 13 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 13 3.2 RADIATION SPURIOUS EMISSIONS .................................................................................................... 14 3.2.1 Applicable Standard ..................................................................................................................................... 14 3.2.2 EUT Setup.................................................................................................................................................... 14 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 15 3.2.4 Test Procedure ............................................................................................................................................. 15 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 15 3.3 6 DB EMISSION BANDWIDTH: ............................................................................................................ 16 3.3.1 Applicable Standard ..............................…

Text truncated - open the document above for the full version.

SHENZHEN TENDA TECHNOLOGY CO.,LTD. Measurement of Antenna for RX12 Pro Project Manufacture：SHENZHEN TENDA TECHNOLOGY CO.,LTD. Add: 6-8 Floor,Tower E3,No.1001,Zhongshanyuan Road, Nanshan District,Shenzhen,China.518052 1. Antenna Appearance: 2. Electrical performance test results at normal temperature SHENZHEN TENDA TECHNOLOGY CO.,LTD. a)2.4G Antenna No Test Item Unit Demand Performance Test Result Judgement 1 Frequency Range MHz 2400-2483 2400-2483 OK 2 Gain dBi 5 2400 4.49 OK 2450 4.47 OK 2483 5.00 OK 3 Isolation dB ≤-15 2400 -26 OK 2450 -25 OK 2483 -24 OK 4 Return loss dB ≤-10 2400 -21 OK 2450 -19 OK 2483 -14 OK B)5G Antenna No Test Item Unit Demand Performance Test Result Judgement 1 Frequency Range MHz 5150-5850 5150-5850 OK 2 Gain dBi 6.0 5150 5.93 OK 5500 5.49 OK 5850 5.34 OK 3 Isolation dB ≤-15 5150 -25 OK 5500 -27 OK 5850 -28 OK 4 Return loss dB ≤-10 5150 -14 OK 5500 -25 OK 5850 -22 OK SHENZHEN TENDA TECHNOLOGY CO.,LTD. Directional diagram for 2.4GHz EUT Remark Frequency E Total. dB(dB) Efficiency( ) 2400MHz 4.49 70% 2410MHz 4.56 73% 2420MHz 4.75 78% 2430MHz 4.83 82% 2440MHz 4.70 84% 2450MHz 4.47 85% 2460MHz 4.58 87% 2470MHz 4.84 92% 2480MHz 5.00 97% 2490MHz 5.09 98% 2500MHz 4.94 96% XOY PLANE XOZ PLANE 3D Radiation patterns at 2450 MHz H PLANE V PLANE 2D Radiation patterns SHENZHEN TENDA TECHNOLOGY CO.,LTD. Directional diagram for 5GHz Frequency E Total. dB(dBi) Efficiency( ) 5000MHz 5.43 68% 5050MHz 5.68 73% 5100MHz 5.75 76% 5150MHz 5.93 77% 5200MHz 5.90 79% 5250MHz 5.86 79% 5300MHz 5.97 80% 5350MHz 6.00 82% 5400MHz 5.85 80% 5450MHz 5.85 81% 5500MHz 5.49 77% 5550MHz 5.41 76% 5600MHz 5.24 74% 5650MHz 4.98 75% 5700MHz 5.12 76% 5750MHz 5.24 77% 5800MHz 4.99 74% 5850MHz 5.34 77% 5900MHz 5.30 74% 5950MHz 5.91 84% 6000MHz 5.58 80% XOY_PLANE XOZ PLANE 3D Radiation patterns at5150 MHz 2D Radiation patterns SHENZHEN TENDA TECHNOLOGY CO.,LTD. 2.4G Return loss test 2.4G Isolation SHENZHEN TENDA TECHNOLOGY CO.,LTD. 5G Return loss test 5G Isolation

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View