VOB-P1001ATango Multimode PCI �E Embedded Module

NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 91 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 15 EXHIBIT C - EUT PHOTOGRAPHS 15.1 EUT- Front Side View 15.2 EUT- Back Side View

NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 86 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 13 EXHIBIT A - FCC ID LABELING REQUIREMENTS 13.1 FCC ID Label Requirements As per FCC §2.925, (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID: XXX123 Where: XXX—Grantee Code, 123—Equipment Product Code As per FCC §15.19, (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID: XXXXXX” (5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 13.2 IC Label Requirements As per IC RSS-Gen §5, the certification number shall appear as follows: IC: XXXXXX-YYYYYYYY Where: • "XXXXXX-YYYYYYYY" is the certification number • "XXXXXX" is the Certificate Holder Number (CHN), made of at most 6 alphanumeric characters (A-Z, 0- 9), assigned by Industry Canada; and • "YYYYYYYY" is the Unique Product Number (UPN), made of at most 11 alphanumeric characters (A-Z, 0-9) assigned by the applicant. • Note 1: The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. • Note 2: Note 1 shall be conspicuously placed in the equipment user manual. • Note 3: Permitted alphanumeric characters used in the CHN and UPN are limited to capital letters (A-Z) and digits (0-9). Other characters, such as "#", "/" or "-", shall not be used. NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 87 of 93 FCC Part 22H/24E, RSS-132/133 Test Report As per IC RSS-Gen §5.2 Equipment Labeling: Equipment subject to certification under the applicable RSS, shall be permanently labeled on each item, or as an inseparable combination. The label must contain the following information for full compliance: (a) the certification number, prefixed by the term “IC:”; (b) the manufacturer's name, trade name or brand name; and (c) a model name or number. Equipment for which a certificate has been issued is not considered certified if it is not properly labeled. The information on the Canadian label can be combined with the manufacturer’s other labeling requirements. If the device size is too small to put a label, the label can be included in the user’s manual, upon agreement with Industry Canada. 13.3 FCC ID & IC Label Contents and Location

NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 92 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 15.3 EUT- Front Side View (Without Shielding) 15.4 EUT- Back Side View (Without Shielding) NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 93 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 15.5 EUT on the Supporting Host View --- END OF REPORT --- EUT

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*＂ (Rev.2) SAR EVALUATION REPORT For NVIDIA Corporation 2701 San Tomas Expressway, Santa Clara, CA 95050, USA FCC ID: VOB-P1001A IC: 7361A-P1001A Report Type: Original Report Product Type: 2G/3G WWAN PCI-E Module for Tablet PC Model E1290 Test Engineer: Arthur Tie Report Number: R1111165-WWAN SAR Report Date: 2011-12-29 Reviewed By: Victor Zhang EMC/RF Lead Prepared By: (SP) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Avenue, Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732 9164 NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1110135-SAR SAR Evaluation Report Page 2 of 89 Summary of Test Results Rule Part(s): FCC §2.1093 IC RSS-102, Issue 4 Test Procedure(s): FCC Bulletin 65OET -C; IEEE 1528-2003 RSS-102, Issue 4 Device Category: Exposure Category: Portable Device General Population/Uncontrolled Exposure Device Type: 2G/3G WWAN PCI-E Module for Tablet PC Model E1290 Modulation Type: GMSK/QPSK/WCDMA 824.2-848.8 MHz GPRS/EDGE 850 826.4-846.6 MHz WCDMA 850 1850.2-1909.8 MHz GPRS/EDGE 1900 TX Frequency Range: 1852.4-1907.6 MHz WCDMA 1900 32.67 dBm GPRS 850 22.57 dBm WCDMA 850 29.68 dBm GPRS 1900 Maximum Conducted Power Tested: 22.45 dBm WCDMA 1900 Antenna Type(s) Tested: Internal Antenna Body-Worn Accessories: None Face-Head Accessories: None 0.218 W/Kg ,Body 1g Tissue GPRS 850 0.176 W/Kg ,Body 1g Tissue WCDMA 850 0.511 W/Kg, Body 1g Tissue GPRS 1900 Max. SAR Level (s) Measured: 1.03 W/Kg, Body 1g Tissue WCDMA 1900 NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1110135-SAR SAR Evaluation Report Page 3 of 89 TABLE OF CONTENTS 1 GENERAL DESCRIPTION ................................................................................................................................5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .......................................................................5 1.2 EUT TECHNICAL SPECIFICATION....................................................................................................................5 2 TEST FACILITY..................................................................................................................................................6 3 REFERENCE, STANDARDS AND GUILDELINES .......................................................................................7 3.1 SAR LIMITS....................................................................................................................................................8 4 DESCRIPTION OF TEST SYSTEM..................................................................................................................9 4.1 IEEE SCC-34/SC-2 P1528 RECOMMENDED TISSUE DIELECTRIC PARAMETERS...........................................10 4.2 MEASUREMENT SYSTEM DIAGRAM..............................................................................................................11 4.3 SYSTEM COMPONENTS..................................................................................................................................12 4.4 DASY4 MEASUREMENT SERVER..................................................................................................................12 4.5 DATA ACQUISITION ELECTRONICS...............................................................................................................13 4.6 PROBES.........................................................................................................................................................13 4.7 ET3DV6 PROBE SPECIFICATION...................................................................................................................13 4.8 E-FIELD PROBE CALIBRATION PROCESS.......................................................................................................14 4.9 DATA EVALUATION......................................................................................................................................14 4.10 LIGHT BEAM UNIT........................................................................................................................................16 4.11 MEDIUM........................................................................................................................................................16 4.12 SAM TWIN PHANTOM..................................................................................................................................17 4.13 DEVICE HOLDER FOR SAM TWIN PHANTOM................................................................................................17 4.14 SYSTEM VALIDATION KITS...........................................................................................................................18 4.15 ROBOT..........................................................................................................................................................19 5 EQUIPMENT LIST AND CALIBRATION.....................................................................................................20 5.1 EQUIPMENTS LIST & CALIBRATION INFO......................................................................................................20 6 SAR MEASUREMENT SYSTEM VERIFICATION .....................................................................................21 6.1 SYSTEM ACCURACY VERIFICATION..............................................................................................................21 6.2 SYSTEM SETUP BLOCK DIAGRAM....................................…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 22H, 24E IC RSS-132, ISSUE 2, SEP 2005 IC RSS-133, ISSUE 5, FEB 2009 TEST AND MEASUREMENT REPORT For NVIDIA Corporation 2701 San Tomas Expressway, Santa Clara, CA 95050, USA Report Type: Original Report Product Type: 2G/3G WWAN PCI-E Module Test Engineer: Lionel Lara Report Number: R1111165-2224 Report Date: 2011-12-28 Reviewed By: Victor Zhang EMC/RF Lead Prepared By: (84) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Avenue, Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732 9164 FCC ID: VOB-P1001A IC: 7361A-P1001A NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 2 of 93 FCC Part 22H/24E, RSS-132/133 Test Report TABLE OF CONTENTS 1 GENERAL INFORMATION ..............................................................................................................................5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT).........................................................................5 1.2 MECHANICAL DESCRIPTION............................................................................................................................5 1.3 OBJECTIVE.......................................................................................................................................................5 1.4 RELATED SUBMITTAL(S)/GRANT(S) ................................................................................................................5 1.5 TEST METHODOLOGY......................................................................................................................................6 1.6 MEASUREMENT UNCERTAINTY.......................................................................................................................6 1.7 TEST FACILITY.................................................................................................................................................6 2 SYSTEM TEST CONFIGURATION..................................................................................................................7 2.1 JUSTIFICATION.................................................................................................................................................7 2.2 EUT EXERCISE SOFTWARE..............................................................................................................................7 2.3 SPECIAL ACCESSORIES....................................................................................................................................7 2.4 EQUIPMENT MODIFICATIONS...........................................................................................................................7 2.5 LOCAL SUPPORT EQUIPMENT..........................................................................................................................7 2.6 POWER SUPPLY AND LINE FILTERS..................................................................................................................7 2.7 INTERFACE PORTS AND CABLING....................................................................................................................8 2.8 INTERNAL PARTS LIST AND DETAILS...............................................................................................................8 3 SUMMARY OF TEST RESULTS.......................................................................................................................9 4 FCC §2.1046, §22.913(A), §24.232 & IC RSS-132 §4.4, RSS-132 §6.4 – RF OUTPUT POWER .................10 4.1 APPLICABLE STANDARD................................................................................................................................10 4.2 TEST PROCEDURE..........................................................................................................................................10 4.3 TEST EQUIPMENT LIST AND DETAILS............................................................................................................10 4.4 TEST ENVIRONMENTAL CONDITIONS.............................................................................................................11 4.5 TEST RESULTS...............................................................................................................................................11 5 FCC §2.1047 & IC RSS-132 §4.2, RSS-132 §6.2 - MODULATION CHARACTERISTIC ..........................13 5.1 APPLICABLE STANDARD................................................................................................................................13 6 FCC §2.1049, §22.917, §22.905, §24.238 & IC RSS-132 §4.5, RSS-133 §6.5 - OCCUPIED BANDWIDTH14 6.1 APPLICABLE STANDARD................................................................................................................................14 6.2 TEST PROCEDURE..........................................................................................................................................14 6.3 TEST EQUIPMENT LIST AND DETAILS............................................................................................................14 6.4 TEST ENVIRONMENTAL CONDITIONS.............................................................................................................14 6.5 TEST RESULTS & PLOTS................................................................................................................................15 7 FCC §2.1051, §22.917 & §24.238(A), IC RSS-132 §4.5 & RSS-132 §6.5 - SPURIOUS EMISSIO…

Text truncated - open the document above for the full version.

NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 88 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 14 EXHIBIT B - TEST SETUP PHOTOGRAPHS 14.1 Radiated Emissions - Front View 14.2 Radiated Emissions below 1 GHz - Rear View NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 89 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 14.3 Radiated Emissions above 1 GHz - Rear View 14.4 RX Radiated Emissions - Front View NVIDIA Corporation FCC ID: VOB-P1001A, IC: 7361A-P1001A Report Number: R1111165-2224 Page 90 of 93 FCC Part 22H/24E, RSS-132/133 Test Report 14.5 Radiated Emissions below 1 GHz - Rear View 14.6 Radiated Emissions above 1 GHz - Rear View