VPYLB1YMCommunication Module

1 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 05 December 2020 LBEE5XV1YMUser Manual for FCC Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). FCC ID:VPYLB1YM 2 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 05 December 2020 LBEE5XV1YM User Manual for FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This devicecomplies with below part 15 of FCC Rules. Part 15 Subpart C Part 15 Subpart E The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This module designed for mounting inside of the end product by us professionally. Therefore, it complies with the antenna and transmission system requirements of §15.203. Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. 3 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 05 December 2020 LBEE5XV1YM User Manual for FCC No.Maker Supported Antenna P/NFormfactorType Gain [dBi] SizeDetail 2.4GHz5GHz 10Molex146153u.FL/flexibleDipole3.24.2535 x 9 x 0.1 mm Flexible// horizontal 11Molex146187u.FL/flexibleDipole3.44.7540.95 x 9 x 0.7 mm Rigid // horizontal We do not mix two antenna ports with the P/N of another antenna. There is only one set of trace line patterns between the U.FL connector and the moduleRF OUT PIN. 4 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 05 December 2020 LBEE5XV1YM User Manual for FCC This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: ±20 ppm ●The following statements must be described on the user manual of the host device of this module; FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. *If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. or Contains Transmitter Module FCC ID:VPYLB1YMContains FCC ID: VPYLB1YM 5 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 05 December 2020 LBEE5XV1YM User Manual for FCC This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. ●When installing it in a mobile equipment. Please describe the following warning to the manual. 6 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 05 December 2020 LBEE5XV1YM User Manual for FCC Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm. ●When installing it in a portable equipment. Please describe the following warning to the manual. It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth). Class II permissive change application is necessary using the SAR report. Please contact Murata. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. Type1VY has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.

RF_160, Issue 04 Declaration of Authorization We Name: Murata Manufacturing Co., Ltd. Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi City: Kyoto Country: Japan 617-8555 Declare that: Name Representative of agent: Jim Chang Agent Company name: SGS Taiwan Ltd. Address: 134, Wu Kung Road, Wu ku Industrial Zone TW- New Taipei City 24803 City: New Taipei City Country: Taiwan is authorized to apply for Certification of the following product(s): Product description: Communication Module Type designation: LBEE5XV1YM Trademark: muRata Validity/ expiry date 2021/1/29 on our behalf. Date: December 1, 2020 City: Kyoto Name: Kenji Hayashikoshi Function: Senior Manager Signature:

FCC, Request for non-disclosure Date: 19-Oct-10 RF_501, Issue 7 Page 1 of 1 Company Name: Murata Manufacturing Co., Ltd. Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi City: Kyoto Country: Japan 617-8555 To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: VPYLB1YM Reference number: Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. Planned Release Date STC: 180 days (notes 2, 3, 4, 5). If no date is given, 45 days from grant date will be used. Date: 01 December 2020 Name and signature of applicant: Kenji Hayashikoshi Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: ____VPYLB1YM____ Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes, the EUT provides the RF shielding 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation. The module and data input(s) are buffered. The EUT has buffered data inputs, it is integrated in IC chip. 3. The modular transmitter must have its own power supply regulation. The module complies the single modular approval request. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The EUT meets the FCC antenna Requirements. Instructions are described in Operational Description. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. The modular transmitter has been performed the testing in a state of being installed on a test jig board simulating the board of the installed end product. It has been performed the testing as a stand-alone and then confirmed the compliance. The module and antenna will be mounted on a board similar to the one shown in the test set photo, and the board will be installed in the end product. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). No. Due to the small size of this module, the FCC ID cannot be printed on the module body. Post the FCC ID in the User manual. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The EUT is compliant with all applicable FCC rules. Details instructions for maintaining compliance are given in the User Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. The EUT is comply with RF exposure re requirement. RF exposure is addressed in the User Manual RF_734_02 04 April 16 Items to be covered by Split modular transmitters. Answer from applicant 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. N/A 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. N/A 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. N/A 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. N/A 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. N/A Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): _Kenji Hayashikoshi _ Date: 01 December 2020 Signature: ___________________________

EUT Photo No.: ER/2020/C0062~67-P Page: 1 of 1 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon ref lects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in f ull, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsif ication of the content or appearance of this document is unlawf ul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group EXTERNAL PHOTOGRAPHS OF EUT Front View of EUT

1 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 24 November 2020 LBEE5XV1YM:Module type SS1234567:Inspection Number BBBBBBBBB:Serial Number :Pin 1 Marking :Name of manufacture(Murata Logo mark) LBEE5XV1YM Label Design to FCC 0.6mm 8.4mm 11.8mm FCC ID:VPYLB1YM Since there is no space which indicates FCC ID. FCC ID is indicated in a manual. LBEE５XV１YM S S 1 2 3 4 5 6 7 BBBBBBBBB : Prohibition labeling area 0.8mm 0.8mm 0.8mm 0.7mm 0.6mm 0.7mm 2.8mm 1.7mm 2.8mm

EUT Photo No.: ER/2020/C0062~67-P Page: 1 of 2 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon ref lects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in f ull, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsif ication of the content or appearance of this document is unlawf ul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group INTERNAL PHOTOGRAPHS OF EUT Internal View of EUT – 1 EUT Photo No.: ER/2020/C0062~67-P Page: 2 of 2 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon ref lects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in f ull, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsif ication of the content or appearance of this document is unlawf ul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Internal View of EUT – 2

Report No: ER/2020/C0067 Page: 1 of 11 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon ref lects the Company’s f indings at the timeof its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction f rom exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group RF EXPOSURE REPORT OF Applicant:Murata Manufacturing Co., Ltd. 1-10-1, Higashikotari, Nagaokakyo-shi, Kyoto 617-8555 Japan Product Name:Communication Module Brand Name:muRata Model No.:LBEE5XV1YM Model Difference:N/A Report Number:ER/2020/C0067 FCC ID:VPYLB1YM IC:772C-LB1YM FCC Rule PartPart 2.1091 IC Rule:RSS-102 issue 5 Mar. 19, 2015 Issue Date:Dec. 30, 2020 We hereby certify that: The above equipment was verified by SGS Taiwan Ltd. The evaluation in this report is in compliance with the above rule(s). The results of this report relate only to the sample identified in this report. Approved By: JohnYeh/ Asst. Manager Report No: ER/2020/C0067 Page: 2 of 11 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon ref lects the Company’s f indings at the timeof its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction f rom exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Revision History Report NumberRevisionDescriptionIssue DateRemark ER/2020/C0067Rev.00Original.Dec. 30, 2020Revised By: Elle Chang Note: 1、Disclaimer Antenna information is provided by the applicant, test results of this report are applicable to the sample EUT received. 2、Measurement results in the original test report ER/2020/80124 are fully leveraged in this test report without further verification test. Report No: ER/2020/C0067 Page: 3 of 11 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon ref lects the Company’s f indings at the timeof its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction f rom exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Table of Contents 1DESCRIPTION OF EQUIPMENT UNDER TEST (EUT)..................................................... 4 2FCC MAXIMUM PERMISSIBLE EXPOSURE (MPE)......................................................... 8 Report No: ER/2020/C0067 Page: 4 of 11 Unless otherwise stated the results shown in this test …

Text truncated - open the document above for the full version.

Report No.: ER/2020/C0062 Page 1 of 75 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues def ined therein. Any holder of this document is advised that information contained hereon reflects the Company’s f indings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction f rom exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsification of the content or appearance of this document is unlawf ul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT Applicant:Murata Manufacturing Co., Ltd. 1-10-1, Higashikotari, Nagaokakyo-shi, Kyoto 617-8555 Japan Product Name:Communication Module Brand Name:muRata Model No.:LBEE5XV1YM Model Difference:N/A Report Number:ER/2020/C0062 FCC ID:VPYLB1YM IC:772C-LB1YM FCC Rule Part:§15.247, Cat: DSS IC RSS:RSS-247 issue 2 Feb 2017 Issue Date:Dec. 30, 2020 Date of Test:Aug. 19, 2020 ~ Sep. 22, 2020 Date of EUT Received: Aug. 19, 2020 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. Central RF Lab The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10:2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits. The test results of this report relate only to the tested sample identified in this report. Approved By: Jay Lin /Asst. Supervisor Report No.: ER/2020/C0062 Page 2 of 75 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible athttp://www.sgs.com.tw/Terms-and-Conditionsand for electronic format documents, subject to Terms and Conditions for Electronic Documents athttp://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues def ined therein. Any holder of this document is advised that information contained hereon reflects the Company’s f indings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction f rom exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or f alsification of the content or appearance of this document is unlawf ul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路 134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Revision History Report NumberRevisionDescriptionIssue DateRemark ER/2020/C0062Rev.00Original.Dec. 30, 2020Revised By: Elle Chang Note: 1、Disclaimer Antenna information is provided by …

Text truncated - open the document above for the full version.