VPYLB2AJCommunication Module

1 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). FCC ID:VPYLB2AJ 2 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This devicecomplies with below part 15 of FCC Rules. Part 15 Subpart C Part 15 Subpart E The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This module designed for mounting inside of the end product by us professionally. Therefore, it complies with the antenna and transmission system requirements of §15.203. Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. 3 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Dimensions. Marking and Terminal Configuration 4 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Pin Layout No.PIN NameNo.PIN NameNo.PIN NameNo.PIN Name 1LTE_UART_RXD30JTAG_TDO59GPIO_1388GND 2PCM_IN/I2S_SD_IN31JTAG_TDI60GPIO_1289VDD_CORE_VM 3PCM_OUT/I2S_SD_OUT32JTAG_TCK61GPIO_990GND 4PCM_CLK/I2S_SCK33JTAG_TRST62NC91GND 5PCM_SYNC/I2S_WS34JTAG_TMS63NC92GND 6GND35NC64NC93GND 7WL_PCIE_RST_L36GND65NC94GND 8WL_PCIE_WAKE_L37BT_RF66NC95GND 9WL_PCIE_CLKREQ_L38GND67GND96GND 10HST_SW_CTRL39NC68WL_EN97GND 11GND40NC69BT_EN98GND 12WL_PCIE_RX_P41DNC70GND99GND 13WL_PCIE_RX_N42DNC71VDD18_IO100GND 14GND43GND72BT_UART_RTS101VDD_FEM_5G 15WL_PCIE_TX_P44GND73BT_UART_CTS102VDD_FEM_5G 16WL_PCIE_TX_N45WL_RF074BT_UART_TXD103GND 17GND46GND75BT_UART_RXD104GND 18WL_PCIE_CLK_N47GND76LTE_UART_TXD105VDD_FEM_2G 19WL_PCIE_CLK_P48NC77VDD_CORE_VH106VDD_FEM_2G 20WL_DB_UART_RXD49NC78GND107GND 21WL_DB_UART_TXD50NC79VDD_CORE_VL108GND 22SLEEP_CLK51NC80GND109GND 23GND52GND81GND110GND 24NC53GND82GND111GND 25NC54WL_RF183VDD_CORE_VH112GND 26GND55GND84GND------ 27HST_CLK_REQ_OUT56GND85VDD_CORE_VL------ 28NC57NC86VDD_CORE_VL------ 29GND58GPIO_887GND------ 5 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Min.Typ.Max.Unit Operating Temperature-40+25+85deg. C DUT_PIN_NameMin.Typ.Max.unit VDD_CORE_VH1.851.952.05V VDD_CORE_VM1.281.351.42V VDD_CORE_VL0.900.951.00V VDD18_IO1.701.801.90V VDD_FEM_2G VDD_FEM_5G 3.503.854.20V Power to VDD_FEM_2G and VDD_FEM_5G must be supplied via an external regulator. Supply Voltage Operating Temperature 6 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Antenna Outline 7 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC No.Maker Supported Antenna P/NFormfactorType Gain [dBi] 2.4GHz5GHz 1TE955-011-901FAKRA Pattern Antenna Max. 2.8dBiMax. 5dBi 2TE955-011-901FAKRA Pattern Antenna Max. 2.8dBiMax. 5dBi 3TE955-011-901FAKRA Pattern Antenna Max. 2.8dBiMax. 5dBi Antenna 8 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Antenna 9 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Antenna 10 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC Antenna Maximum antenna gain including RF cable is below: Antenna PortMax. Gain [dBi] 2.4GHz5GHz WLAN1-3.3-5.0 WLAN2/BT-1.9-2.3 11 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 21 January 2021 LBEE6ZZ2AJ User Manual for FCC This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: ±20 ppm ●The following statements must be described on the user manual of the host device of this module; FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. *If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause und…

Text truncated - open the document above for the full version.

RF_160, Issue 04 Declaration of Authorization We Name: Murata Manufacturing Co., Ltd. Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi City: Kyoto Country: Japan 617-8555 Declare that: Name Representative of agent: Jim Chang Agent Company name: SGS Taiwan Ltd. Address: 134, Wu Kung Road, Wu ku Industrial Zone TW- New Taipei City 24803 City: New Taipei City Country: Taiwan is authorized to apply for Certification of the following product(s): Product description: Communication Module Type designation: LBEE6ZZ2AJ Trademark: muRata Validity/ expiry date March 31, 2021 on our behalf. Date: January 20, 2021 City: Kyoto Name: Kenji Hayashikoshi Function: Senior Manager Signature:

FCC, Request for non-disclosure Date: 19-Oct-10 RF_501, Issue 7 Page 1 of 1 Company Name: 10-1, Higashikotari 1-chome, Nagaokakyo-shi Address: 9200 Cody, Overland Park , Kansas, United States City: Kyoto Country: Japan 617-8555 To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: VPYLB2AJ Reference number: Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. Planned Release Date STC: 180 days (notes 2, 3, 4, 5). If no date is given, 45 days from grant date will be used. Date: 20 January 2021 Name and signature of applicant: Kenji Hayashikoshi Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: ____ VPYLB2AJ ____ Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes, the EUT provides the RF shielding 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation. The module and data input(s) are buffered. The EUT has buffered data inputs, it is integrated in IC chip. 3. The modular transmitter must have its own power supply regulation. No. VDD_FEM does not have a regulator inside the module. Therefore, we show our customers that VDD_FEM power is supplied via an external regulator. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The EUT meets the FCC antenna Requirements. Instructions are described in Operational Description. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. The modular transmitter has been performed the testing in a state of being installed on a test jig board simulating the board of the installed end product. It has been performed the testing as a stand-alone and then confirmed the compliance. The module and antenna will be mounted on a board similar to the one shown in the test set photo, and the board will be installed in the end product. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). The FCC ID is marked with a laser on the metal case as shown in Label Drawing & Location. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The EUT is compliant with all applicable FCC rules. Details instructions for maintaining compliance are given in the User Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. The EUT is comply with RF exposure re requirement. RF exposure is addressed in the User Manual RF_734_02 04 April 16 Items to be covered by Split modular transmitters. Answer from applicant 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. N/A 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. N/A 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. N/A 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. N/A 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. N/A Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): _Kenji Hayashikoshi _ Date: 21 January 2021 Signature: ___________________________

Date: January 20, 2021 DTS-UNII Device Declaration Letter To Whom It May Concern, we declare below featured for equipment authorization regarding FCC ID: VPYLB2AJ ISED Certification Number: 772C-LB2AJ (1) DFS Device -- ☐ Master, ☐ Client with Radar detection capability, ☒ Client without radar detection capability, ☐ N/A (2) Active / Passive Scanning Frequency Band(MHz) Active Scanning (able to select a channel and initiate a network by sending enabling signals to other devices) passive scanning (not able to initiate a network) Non Applicable 2412 - 2462 ☒ Yes , ☐ No ☐ Yes , ☒ No ☐ 5150 - 5250 ☒ Yes , ☐ No ☐ Yes , ☒ No ☐ 5250 - 5350 ☐ Yes , ☒ No ☒ Yes , ☐ No ☐ 5470 - 5725 ☐ Yes , ☒ No ☒ Yes , ☐ No ☐ 5725 - 5850 ☒ Yes , ☐ No ☐ Yes , ☒ No ☐ (3) Country code selection ability - ☒ Yes , ☐ No If yes, pls explain how it was implemented : Country code is factory set in the UI and cannot be changed by end users. (4) Meet 15.202 requirement - ☒ Yes , ☐ No pls check below : ☐ A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices. ☒ A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. Signature: Name (Printed) / Title: Kenji Hayashikoshi / Senior Manager On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: +81-75-955-6173 Address: 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto Japan 617-8555

EUT Photo No.: ER/2020/B0044~49-P Page: 1 of 1 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.com.tw Member of SGS Group PHOTOGRAPHS OF EUT Front View of EUT Back View of EUT

1 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 22 January 2021 CONFIDENTIAL LBEE6ZZ2AJ Label drawing and Location 22.6mm M D123 2AJxxx 123456789ABCDEFG (2) (3) (4) (5) (9) (1) Model:LBEE6ZZ2AJ(6) FCCID:VPYLB2AJ(7) IC:772C-LB2AJ(8) 22.6mm MarkingInformationonsurface (1)2DBarcode (2)MurataCompanyLogo (3)WeeklyCode (4)MurataPartNumber (5)MurataUniqueNumber (6)ModelNumber (7)FCCID (8)ICID (9)#1pinDirectionMarking

EUT Photo No.: ER/2020/B0044~49-P Page: 1 of 1 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.com.tw Member of SGS Group PHOTOGRAPHS OF EUT Internal View of EUT

Report No: ER/2020/B0049 Page: 1 of 12 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.com.tw Member of SGS Group RF EXPOSURE REPORT OF Applicant: Murata Manufacturing Co., Ltd. 1-10-1, Higashikotari, Nagaokakyo-shi, Kyoto 617-8555 Japan Product Name: Communication Module Brand Name: muRata Model No.: LBEE6ZZ2AJ Model Difference: N/A Report Number: ER/2020/B0049 FCC ID: VPYLB2AJ IC: 772C-LB2AJ FCC Rule Part Part 2.1091 IC Rule: RSS-102 issue 5 Mar. 19, 2015 Issue Date: Feb. 08, 2021 We hereby certify that: The above equipment was verified by SGS Taiwan Ltd. The evaluation in this report is in compliance with the above rule(s). The results of this report relate only to the sample identified in this report. Approved By: John Yeh / Asst. Manager Report No: ER/2020/B0049 Page: 2 of 12 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.com.tw Member of SGS Group Revision History Report Number Revision Description Issue Date Remark ER/2020/B0049 Rev.00 Original. Feb. 08, 2021 Revised By: Yuri Tsai Note: 1、 Disclaimer Antenna information is provided by the applicant, test results of this report are applicable to the sample EUT received. Report No: ER/2020/B0049 Page: 3 of 12 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.com.tw Member of SGS Group Table of Contents 1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................... 4 2 FCC MAXIMUM PERMISSIBLE EXPOSURE (MPE)....................................................... 10 Report No: ER/2020/B0049 Page: 4 of 12 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣…

Text truncated - open the document above for the full version.

Report No.: ER/2020/B0047 Page: 1 of 455 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.com.tw Member of SGS Group ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT Applicant: Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555 Japan Product Name: Communication Module Brand Name: muRata Model No.: LBEE6ZZ2AJ Model Difference: N/A Report Number: ER/2020/B0047 FCC ID VPYLB2AJ IC: 772C-LB2AJ FCC Rule Part: §15.407, Cat: U-NII ISED RSS: RSS-247 issue 2 Feb. 2017 Issue Date: Feb. 22, 2021 Date of Test: Nov. 19, 2020 ~ Jan. 12, 2021 Date of EUT Re- ceived: Nov. 19, 2020 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. Central RF Lab The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10: 2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits. The test results of this report relate only to the tested sample identified in this report. Approved By: Jim Chang / Manager Report No.: ER/2020/B0047 Page: 2 of 455 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.sgs.…

Text truncated - open the document above for the full version.